Sonos RM002 802.11 b/g MIMO Mini-PCI Card User Manual WMP N06 User Guide 20090911
Sonos, Inc. 802.11 b/g MIMO Mini-PCI Card WMP N06 User Guide 20090911
Sonos >
User manual
Product External Specifications For 802.11b/g /n MIMO Mini-PCI Card (Atheros Solution) WMP-N06 Revision: 1.2 Alpha Networks Proprietary and Confidential Information FCC Statement : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. FCC RF Radiation Exposure Statement: 1.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Modular Approval This device is intended only form OEM integrator under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Alpha Networks Proprietary and Confidential Information End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment). The final end product must be labeled in visible area with the following: “Contains RF Module FCC ID: SBVRM002 End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.” Alpha Networks Proprietary and Confidential Information 1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11b/g MIMOMini-PCI Card. This Mini-PCI Card is based on Atheros AR5008 chipset that complied with IEEE 802.11n draft 1.0 standard from 2.4~2.5GHz, and it can be used to provide up to 11Mbps for IEEE 802.11b and 54Mbps/108Mbps for 2.4GHz IEEE 802.11g to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11b/g MIMOMini-PCI Card offers absolute interoperability with different vendors’ 802.11b/g MIMO Access Points through the wireless LAN. 1.2 Product Features Compatible with IEEE 802.11b high rate standard to provide wireless 11Mbps data rate Compatible with IEEE 802.11g higher speed standard to provide wireless 54Mbps data rate, and the turbo mode of 108Mbps (For USA) Operation at 2.4 ~ 2.5GHz frequency band to meet worldwide regulations Dynamic date rate scaling at 6, 9, 12, 18, 24, 36, 48, 54 and 108Mbps for 802.11g Dynamic date rate scaling at 1, 2, 5.5, and 11Mbps for IEEE 802.11b Compatible with IEEE 802.11n draft 1.0 higher speed standard in High Throughput mode from MCS-0 to MCS15. The HT data rate refers to Appendix I. Maximum reliability, throughput and connectivity with automatic data rate switching Supports wireless data encryption with 64/128/152-bit WEP for security Support Super G mode to provide the higher data rate and throughput Supports WPA and AES enhanced security Supports DFS/TPC for European operation Supports VLAN tagging Friendly user configuration and utilities Drivers support Windows 98SE, ME, 2K, and XP Supports Mini-PCI Type IIIA form factor 2.0 Requirements The following sections identify the detailed requirements of the 802.11g Mini-PCI Card. 2.1 Functional Block Diagram Mini AR5416 ( EWC MIMO ) MAC/BB SoC RF-Front End Circuit Chain 3 PCI RF-Front End Circuit Chain 2 I/O AR2133 ( EWC MIMO ) 2400~2497MHz Transceiver RF-Front End Circuit Chain 1 Alpha Networks Proprietary and Confidential Information 2.2 General Requirements 2.2.1 IEEE 802.11b Section Feature Detailed Description 2.2.1.1 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK 2400 ~ 2497MHz ISM band Data Rate Media Access Protocol Transmitter Output Power 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK 2.2.1.3 2.2.1.4 2.2.1.5 2.2.1.6 2.2.1.7 2.2.1.8 Receiver Sensitivity Typical RF Output Power at each RF chain, Data Rate and at room Temp. 25degree C( tolerance ±2dB) under 3.3VDC operating voltage 18dBm at 11, 5.5, 2, and 1Mbps Typical –84dBm for 11Mbps @ 8% PER Typical –90dBm for 2Mbps @ 8% PER 2.2.2 IEEE 802.11g Section Feature Detailed Description 2.2.2.1 2.2.2.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers IEEE 802.11g BPSK, QPSK, 16QAM, 64QAM, and OFDM 2400 ~ 2483.5MHz ISM band Data Rate Media Access Protocol Transmitter Output Power 11 channels for United States 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK 2.2.2.3 2.2.2.4 2.2.2.5 2.2.2.6 2.2.2.7 2.2.2.8 Receiver Sensitivity Typical RF Output Power at each RF chain, Data Rate and at room Temp. 25degree C (tolerance ± 2dB) under 3.3VDC operating voltage 19dBm at 6~24 Mbps 17dBm at 36 Mbps 16dBm at 48 Mbps 15dBm at 54 Mbps Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% –86dBm at 6Mbps –86dBm at 9Mbps –84dBm at 12Mbps –82dBm at 18Mbps –78dBm at 24Mbps –75dBm at 36Mbps –71dBm at 48Mbps Alpha Networks Proprietary and Confidential Information # Feature Detailed Description –70dBm at 54Mbps 2.2.3 IEEE 802.11n Section Feature Detailed Description 2.2.3.1 2.2.3.2 Standard Radio and Modulation Type Operating Frequency Channel Numbers IEEE 802.11n draft 1.0 BPSK, QPSK, 16QAM, 64QAM with OFDM Data Rate Media Access Protocol Transmitter Output Power 2400 ~ 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 13 channels for Japan From MCS – 0 to MCS –15 as shown in Appendix A CSMA/CA with ACK 2.2.3.3 2.2.3.4 2.2.3.5 2.2.3.6 2.2.3.7 2.2.3.8 Receiver Sensitivity Typical RF Output Power at each RF chain, Data Rate and at room Temp. 25degree C (tolerance ± 2dB) under 3.3VDC operating voltage HT20: 19dBm at MCS - 0 ~ 4, MCS 8 ~ 12 17dBm at MCS - 5, 13 13dBm at MCS - 6, 14 8dBm at MCS - 7, 15 HT40: 15dBm at MCS - 0 ~ 4, MCS 8 ~ 12 15dBm at MCS - 5, 13 13dBm at MCS - 6, 14 8dBm at MCS - 7, 15 Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% –88dBm at BPSK, coding rate 1/2 (MCS-0) –84dBm at QPSK, coding rate 1/2 (MCS-1) –81dBm at QPSK, coding rate 3/4 (MCS-2) –78dBm at 16-QAM, coding rate 1/2 (MCS-3) –75dBm at 16-QAM, coding rate 3/4 (MCS-4) –70dBm at 64-QAM, coding rate 2/3 (MCS-5) –69dBm at 64-QAM, coding rate 3/4 (MCS-6) –68dBm at 64-QAM, coding rate 5/6 (MCS-7) 2.2.4 General Section Feature 2.2.4.1 2.2.4.2 2.24.3 Antenna Connector Three UFL antenna connectors Operating Voltage 3.3VDC +/- 10% Current 800mA at continuous transmit mode (2 Tx chains on ) Consumption 450mA at continuous receive mode (3 Rx chains on ) Form Factor and Mini-PCI Type IIIA form factor Alpha Networks Proprietary and Confidential Information 2.2.4.4 Detailed Description 2.2.4.5 Interface LEDs External LED function supported Alpha Networks Proprietary and Confidential Information 2.3 Software Requirements The Configuration Software supports Microsoft Windows 98SE, ME, 2000, and XP. This configuration software includes the following functions: Information Information allows you to monitor network status. Configuration Configuration allows you to configure parameters for wireless networking. Security Supports enhanced security WEP, 802.1x,WPA. 2.3.1 Information Feature Detailed Description 2.3.1.1 General Information 2.3.1.2 Current Link Information 2.3.1.3 Site survey General Information shows the name of Wireless Adapter, Adapter MAC Address, Regulatory Domain, Firmware Version, and Utility Version. Current Link Information shows the Current Setting ESSID, Channel Number, Associated BSSID, Network Type (infrastructure or Ad-hoc network), WEP Status (enable or disable), Link Status (Connect or Disconnect), 802.11g Transmit Speed (6, 9, 12, 18, 24, 36, 48, 54Mbps), 802.11b Transmit Speed (1, 2, 5.5, 11Mbps), Signal Strength, and Link Quality. To search the neighboring access points and display the information of all access points. 2.3.2 Configuration Feature Detailed Description 2.3.2.1 ESS ID 2.3.2.2 Network Type Input an SSID number if the roaming feature is enabled Supports for ASCII printable characters. Ad-hoc Mode and 802.11 Ad-hoc Mode for network configurations that do not have any access points Infrastructure Mode for network configurations with access points Extend the battery life of clients by allowing the client to sleep for short periods of time while the Access Point buffers the messages. Set the number of bytes used for fragmentation boundary for messages Set the number of bytes used for RTS/CTS boundary This indicates the communication rates. Select appropriate transmission speed to match your wireless LAN settings Support Automatic or Manual Rescan to associate with access point. 2.3.2.3 Power Save 2.3.2.4 RTS Threshold 2.3.2.5 2.3.2.6 Fragment Threshold Transmission Speed 2.3.2.7 Roaming Feature Detailed Description 2.3.3.1 Encryption 2.3.3.2 WEP Management 2.3.3 Security RC4 encryption algorithm Support 64/128/152 bit WEP encryption Support open system and shared key authentication Four WEP keys can be selected Alpha Networks Proprietary and Confidential Information # Feature Detailed Description 2.3.3.3 2.3.3.4 802.1x WPA STA with WEP off will never associate any AP with WEP enabled WEP Key Format: Option for Hex format Support EAP-TLS, EAP-TTLS, and EAP-PEAP Support WPA-PSK and WPA-EAP Support Cipher Mode AES and TKIP 2.4 Mechanical Requirements Feature Detailed Description 2.4.1 2.4.2 2.4.3 Length Width Height 50.8mm 59.59mm 0.99mm 2.5 Compatibility Requirements This device passes the following compatibility requirements. Feature Detailed Description 2.5.1 2.5.2 2.5.3 Wi-Fi WHQL Physical Layer and Functionality Meet Wi-Fi certification for IEEE 802.11 product Meet applicable WHQL certification requirements Meet ALPHA Engineering Test Plan and Test Report 2.6 Requirements of Reliability, Maintainability and Quality Feature Detailed Description 2.6.1 2.6.2 2.6.3 MTBF Maintainability Quality Mean Time Between Failure > 30,000 hours There is no scheduled preventive maintenance required The product quality is followed-up by ALPHA factory quality control system 2.7 Environmental Requirements Feature Detailed Description 2.7.1 Operating Temperature Conditions Non-Operating Temperature Conditions The product is capable of continuous reliable operation when operating in ambient temperature of 0 ℃ to +55℃. Operating Humidity conditions Non-Operating Humidity Conditions Neither subassemblies is damaged nor the operational performance is degraded when restored to the operating temperature after exposing to storage temperature in the range of –20 ℃ to +75 ℃. The product is capable of continuous reliable operation when subjected to relative humidity in the range of 10% and 90% non-condensing. The product is not damaged nor the performance is degraded after exposure to relative humidity ranging from 5% to 95% non-condensing 2.7.2 2.7.3 2.7.4 Alpha Networks Proprietary and Confidential Information Appendix I: Rate Dependent Parameters for High Throughput . Modulation and Coding Schemes (MCS) The parameters in the table are: ■ Rate: Rate in Mbps ■ NES: Number of FEC encoders used ■ NSD: Number of Data Subcarriers ■ NCBPS: Number of Code Bits Per Symbol (total of all spatial streams) ■ NSS: Number of Spatial Streams Alpha Networks Proprietary and Confidential Information 10 Test Environment Diagram Fixed Attenuator (30dB) * 3 pcs Splitter (1 對 3) IP: 192.168.100.254 (Note: :For IQ-View / IQ-Flex) ) Normal Test Operating Procedure 1. Testing Steps: 8 steps in total P.S.:Pls. Install driver before insert the card. [Step 1] Run ” BC_LOG.exe ” at DUT (see Figure 1) to open test window Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\ BC_LOG.exe (Figure 1) Alpha Networks Proprietary and Confidential Information 11 [Step 2] Run ” GUI.exe ” at DUT (see Figure 3) to open test window (see Figure 4). Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\ GUI.exe (Figure 3) (Figure 4) Alpha Networks Proprietary and Confidential Information 12 [Step 3] Then Kevin Serial number (see Figure 5) (Figure 5) [Step 4] (a) Plug DUT into MINI PCI / CARD BUS Interface (b) Plug RF Cable on DUT antenna three point and user a special line (MAIN-From Left to Right 0.1.2) [Step 5] Click “Run Production Test Software” to begin test. (See Figure 6) (Figure 6) Alpha Networks Proprietary and Confidential Information 13 [Step 6] Testing. (See Figure 7) (Figure 7) Alpha Networks Proprietary and Confidential Information 14 [Step 7] When test finish, it will show “PASS”(see Figure 8). (Figure 8) Alpha Networks Proprietary and Confidential Information 15 [Step 8] When show “PASS”, click “ Test ” and change the next one to continue (see Figure 8). Test Program setup [步驟 步驟 1] search the program file of ” IQ_attn.txt ” see Figure 1), (Ex: Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\iq_setup\ IQ_attn.txt) (Figure 1) Alpha Networks Proprietary and Confidential Information 16 [步驟 步驟 2] Test Fail (see Figure 2), (Figure 2) Alpha Networks Proprietary and Confidential Information 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 17 Producer : GPL Ghostscript 8.15 Create Date : 2009:09:11 11:51:39 Modify Date : 2009:09:11 11:51:39 Title : Microsoft Word - WMP-N06_User Guide_20090911.doc Creator : PScript5.dll Version 5.2 Author : 05777EXIF Metadata provided by EXIF.tools