Sonova USA HUB Inspiro Audio hub User Manual Manual

Phonak Inc Inspiro Audio hub Manual

Manual

Inspiro audioHub legal information (029-3138) Inspiro audioHub Equipment and accessories  inspiro audioHub  Universal power supply US/EU  Audio cable 3.5 mm jack-jack (1m)  Cinch to 3.5 mm  Packaging insert  Declaration of Conformity Declaration of Conformity Hereby, Phonak Communications AG, Länggasse 17, CH-3280 Murten, declares that the inspiro audioHub is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. To obtain a copy of the Declaration of conformity, please contact the manufacturer or the local Phonak representative whose address can be taken from the list on www.phonak.com (worldwide locations). This device complies with Part 15 and part 95 of the FCC Rules and with RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. To comply with FCC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. This transmitter is authorized by rule under the Low Power Radio Service (47 CFR part 95) and must not cause harmful interference to TV reception or United States Navy SPASUR installations. You do not need an FCC license to operate this transmitter. This transmitter may only be used to provide: auditory assistance to persons with disabilities, persons who require language translation, or persons in educational settings; health care services to the ill; law enforcement tracking services under agreement with a law enforcement agency; or automated maritime telecommunications system (AMTS) network control communications. Two way voice communications and all other types of uses not mentioned above are expressly prohibited. This device may not interfere with TV reception or Federal Government radar. For Canada: if TV channel 13 is used in the area, the installer shall reduce or adjust the radio frequency radiated power so that nearby TV channel 13 receivers do not receive radio interference from the system installed. Suggestions: A test with a TV receiver equipped with a “rabbit-ear antenna” and tuned to channel 13 should be conducted at the perimeter of the user’s intended coverage area and should not overlap other users’ areas without the latter’s consent. If this does not solve the problem, a channel near the 217 MHz edge and not near 216 MHz should be tried. This Class B digital apparatus complies with Canadian ICES-003. To comply with Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Information and explanation of symbols The CE symbol is confirmation that this Phonak product meets the requirements of the R&TTE Directive 1999/5/EC on Radio and Telecommunication Terminal Equipment. The alert sign means that potential restrictions on its use are applicable in one or more EU Member States. The symbol with the crossed out disposal bin indicates that the product shall not be treated as household waste. Please hand over your old or unused product to the applicable collection point for the recycling of electrical and electronic equipment or bring your old product to your hearing care professional for appropriate disposal. By ensuring this product is disposed of correctly, you will help prevent potential negative effects on the environment and human health. Connecting the device to mains power Select an easily accessible socket outlet and plug the power supply unit into the socket outlet. The device features input and output mini-USB connectors which both have the following electrical characteristics: 5V 1A in, 0.77A out Alternatively to plugging the power supply to the mains, this device can be power-supplied through USB (version 2.0 or higher) using a USB cable. Procedure for charging an inspiro Switch OFF inspiro device and place it on the USB holder of inspiro audio Hub mechanical top housing.

Navigation menu