Sony Engineering FFS-U RF glow-stick receiver User Manual FFS R
Sony Engineering Corporation RF glow-stick receiver FFS R
User Manual
FreFlow® Instruction Manual 4-545-184-01(1) ©2014 Sony Engineering Corporation Printed in Japan Before operating the product, please read this manual thoroughly and retain it for future reference. Design and specifications are subject to change without notice. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Notes on Use Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. You are cautioned that any changes or modifications not expressly approved in this manual could void the user’s authority to operate the equipment. Do not put small parts or batteries in your mouth. Doing so may lead to choking or serious injury. Keep out of reach of children as there is a risk of choking or serious injury due to accidental swallowing. If batteries are swallowed, seek medical treatment immediately. Material leaked from batteries getting in the eyes, on skin, or on clothing may lead to loss of sight or other injury. Flush any battery material with large volumes of water, and consult a physician. Do not look into the light from the product or shine it directly at eyes. Doing so may lead to vision disorders. Do not disassemble or modify the product. Doing so may lead to fire, injury, etc. The product is not waterproof. Do not allow it to get wet nor use it in water. Doing so may lead to electrical shock or damage to the product. Do not apply strong impact or swing the product around. Doing so may lead to injury or damage to the product. Do not use the product if malfunctioning or damaged. Doing so may lead to shock or injury. Immediately remove the batteries and discontinue use if... the product is dropped or subjected to an impact in which the interior is exposed. the product emits a strange smell, heat, or smoke. When dirty, this unit may be cleaned with a clean, dry cloth. Do not allow this unit to come in contact with alcohol or other chemicals. Signal reception may be impaired in some wireless operating environments. If you feel ill while using the product, turn off the power and discontinue use. How to Use Pull out insulation sheet. Insulation sheet Slide to power switch to the ON position, to turn on the light. It may take a few seconds to light up. Power switch Color change button The light color set will change each time the color change button is pressed. 4-545-184-01(1) Operation With a FreFlow® Wireless System Wait with the power switch set to ON. You do not need to make any special operations. Operation will start automatically when a wireless signal is received. Light color will change by wireless command only in a venue where a FreFlow® wireless system is set up. Light color cannot be changed by the color change button while a wireless signal is being received. When a wireless signal is no longer received, you can operate the product as you like. How to Replace Batteries Push the tab in the direction indicated by the arrow, and remove the battery box cover. Tab Cover Set the batteries with the + and – terminals in the correct direction. Remove the batteries when they are depleted or when not using for a long period of time. Do not use or leave in places with intense direct sunlight or in hot locations such as a car in the sun. Use new batteries when replacing the batteries. Do not mix with old batteries, different types of batteries, etc. Do not subject batteries to fire or high temperatures. Tape over battery contacts to avoid short-circuit when disposing of batteries, and follow local regulations for battery disposal. Specifications Model Name: FFS-R series Materials Grip, cover: ABS / Cylinder: PET Power Requirement Two size AAA (LR03) alkaline batteries: 3.0 V DC MADE IN VIETNAM [For inquires] Antinos Management America, Inc. freflow.service@amaa-us.com FreFlow® and its logo are trademarks or registered trademarks of Sony Engineering Corporation. Insert the batteries, making sure the + and – terminals are in the correct direction, and close the cover securely. 4-545-184-01(1)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : Sony Engineering Corporation Create Date : 2014:05:16 14:01:21+09:00 Modify Date : 2014:05:28 13:34:19+09:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Adobe InDesign CS5.5 (7.5.3) Metadata Date : 2014:05:28 13:34:19+09:00 Format : application/pdf Title : FFS-R Creator : Sony Engineering Corporation Trapped : False Producer : Acrobat Distiller 10.1.9 (Windows) GTS PDFX Conformance : PDF/X-1a:2001 GTS PDFX Version : PDF/X-1:2001 Version ID : 1 Document ID : uuid:885d7cbb-30e3-4cb2-8070-763adf2df345 Instance ID : uuid:771dea15-cd94-4ad8-85c2-45b2f3d3e283 Page Count : 2EXIF Metadata provided by EXIF.tools