Sony Group CPWL0102U 802.11bgn WLAN Module User Manual B010 datasheet V03 201008023 Sony

Sony Corporation 802.11bgn WLAN Module B010 datasheet V03 201008023 Sony

User Manual

CWPL Series 第 1 頁，共 15 頁 CWPL series Hardware Specification Rev. 0.3
CWPL Series 第 2 頁，共 15 頁 Document Revision History Document Revision Date Modifier Comments 0.1 Apr. 19, 2010 Yishin Wu Initial release 0.2 Aug. 13, 2010 Yishin Wu Add Power consumption, Tx power Spec, Rx Sensitivity, Module perspective, Mechanical drawing, Label drawing, 0.3 Aug. 23, 2010 Yishin Wu Update Label content, Ragulatory
CWPL Series 第 3 頁，共 15 頁 Contents 1. INTRODUCTION ...................................................................................... 6 1.1 Product Overview ......................................................................................... 6 1.2 Key Features ................................................................................................. 6 3. ELECTRICAL SPECIFICATIONS ............................................................ 7 3.1 Pin Definitions .............................................................................................. 7 3.2 DC Specifications ......................................................................................... 8 3.2.1 Power Consumption Specifications......................................................... 8 4. RF SPECIFICATION .............................................................................. 9 4.1 TX Specifications .......................................................................................... 9 4.2 RX Specifications ....................................................................................... 10 4.3 Antenna Specifications .............................................................................. 11 5. MECHANICAL SPECIFICATIONS ........................................................ 12 5.1 Mechanical Drawing ................................................................................... 12 5.2 RF connector .............................................................................................. 13 5.2.1 Specification ............................................................................................ 13 5.2.2 Dimensions: (Unit: mm) .......................................................................... 13 5.3 Label Specifications ................................................................................... 13 6. ENVIRONMENTAL SPECIFICATIONS ................................................. 14
CWPL Series 第 4 頁，共 15 頁 7. PART NUMBERING ............................................................................... 14 7.1 Part Numbering ........................................................................................... 14 7.2 ID Definitions .............................................................................................. 15 8. REGULATORY ....................................................................................... 15
CWPL Series 第 5 頁，共 15 頁 Figures Figure 2.2 CWPL010 Series block diagram .................................................... 7 Figure 4.1 Two Connector- CWPL010 series perspective ............................. 11 Figure 5.1 Two Connector- CWPL010 series mechanical drawing .............. 12 Figure 5.2 RF connector Dimensions ............................................................. 13 Figure 5.3 CWPL0102U Label drawing ........................................................... 13 Figure 7.1 Part Numbering ............................................................................... 14 Tables Table 3.1 Pin Definitions .................................................................................... 7 Table 3.2 DC Specifications ............................................................................... 8 Table 3.3 Power Consumption Specifications ................................................. 8 Table 4.1 TX Specifications ............................................................................... 9 Table 4.2 RX Specifications ............................................................................. 10 Table 6.1 Operating Conditions ....................................................................... 14 Table 6.2 Non-operating Conditions ............................................................... 14 Table 7.1 ID Definitions .................................................................................... 15
CWPL Series 第 6 頁，共 15 頁 1. Introduction 1.1 Product Overview The Sony CWPL010 series wireless LAN module contains the Ralink® RT3370 single chip which is a highly integrated MAC/BBP for 2.4GHz RF transmission and supporting 150Mbps PHY rate. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance. The optimized radio frequency architecture and baseband algorithms provide super performance and low power consumption. Deploy a high efficient USB engine and hardware data processing accelerators without overloading the host processor. Security, quality of service and international regulation are supported by CWPL010 series and giving end users the greatest performance anytime in any circumstance. 1.2 Key Features  Legacy data rates 1, 2 in DSSS mode and rates 5.5, and 11 Mbps in CCK mode, 6, 9, 12, 18, 24, 36, 48, and 54 in OFDM mode  Support 40MHz wide channel bandwidth  Uses the 2.412 to 2.497GHz ISM frequency band defined by the IEEE 802.11b/g/n specifications  Reverse direction grant data flow and frame aggregation  WEP 64/128, WPA, WPA2, TKIP, AES  QoS-WMM, WMM-PS, WPS, PIN, PBC  Multiple BSSID Support  Form Factor: PCI Express 1.1 Half Mini Card(single side)  International Regulation – 802.11d + h  Cisco CCX Support up to v5.0  Operating Systems – Windows XP 32/64, 2000, Vista 32/64, Linux, Macintosh,Win7 32/64
2. System Architecture Figure 2.1 3. Electrical Specifications3.1 Pin Definitions Signal Group Signal USB Interface D+ D- Power +5.0V +5.0V GND WSP WSP GND GND 第 7 頁，共 15 頁 2. System Architecture Figure 2.1 CWPL010 Series block diagram Electrical Specifications Table 3.1 Pin Definitions Name Pin No. Direction UDP 2 Input/Output differential pairUDM 3 Input/Output differential pairUV+ 4 Input +5.0V sourceGND 1 N/A Return current pathWSP 6 Input/Output GND 5 N/A Return current pathCWPL Series Description differential pair for transmit differential pair for receive V source Return current path Return current path
CWPL Series 第 8 頁，共 15 頁 3.2 DC Specifications The Max Power (as max defined in USB Spec) is 2500mW  500mA For all USB voltage rails (5.0V), it is recommended not to exceed 100mVpp noise in the frequency range of 10-500KHz. Table 3.2 DC Specifications Parameters Symbol Conditions Min. Typ. Max. Unit 5V Supply Voltage +UV - 4.75 5.0 5.25 V 3.2.1 Power Consumption Specifications Power consumption is measured using current probe loop on the Power rails of the USB interface (Pins). Assuming ASMP enabled (L1-active enabled and L0s is disabled). Table 3.3 Power Consumption Specifications Test Mode Description Idle Power Consumption of idle. Assuming average power consumption is in room temperature. Average Power: 575 mW 1 Stream Transmitting and Receiving Power Consumption of Transmit and Receive state, assuming Single spatial stream transmission for 802.11b network Average Power: 1085 mW 1 Stream Transmitting and Receiving Power Consumption of Transmit and Receive state, assuming Single spatial stream transmission for 802.11g network Average Power: 930 mW 1 Stream Transmitting and Receiving Power Consumption of Transmit and Receive state, assuming Single spatial stream transmission for 802.11n (HT20) network Average Power: 985 mW 1 Stream Transmitting and Receiving Power Consumption of Transmit and Receive state, assuming Single spatial stream transmission for 802.11n (HT40) network Average Power: 975 mW
CWPL Series 第 9 頁，共 15 頁 4. RF Specification 4.1 TX Specifications Table 4.1 TX Specifications ModData Rate (Mbps) Modulation Tx Target Power (dBm) Data Rate (Mbps) Modulation Tx Target Power (dBm) 1 DBPSK 15 HT20-7.22 BPSK 15 2 DQPSK 15 HT20-14.44 QPSK 15 5.5 CCK 15 HT20-21.67 QPSK 15 11 CCK 15 HT20-28.89 16-QAM 15 6 OFDM 15 HT20-43.33 16-QAM 15 9 OFDM 15 HT20-57.78 64-QAM 15 12 OFDM 15 HT20-65 64-QAM 14 18 OFDM 15 HT20-72.22 64-QAM 14 24 OFDM 15 HT40-15 BPSK 15 36 OFDM 15 HT40-30 QPSK 15 48 OFDM 15 HT40-45 QPSK 15 54 OFDM 15 HT40-60 16-QAM 15 HT40-90 16-QAM 15 HT40-120 64-QAM 15 HT40-135 64-QAM 14 HT40-150 64-QAM 14 ※Each tolerance is ±1.5dBm
CWPL Series 第 10 頁，共 15 頁 4.2 RX Specifications Table 4.2 RX Specifications Data Rate (Mbps) Modulation Rx Sensitivity (dBm) Data Rate (Mbps) Modulation Rx Sensitivity (dBm) 1 DBPSK -92 HT20-7.22 BPSK -87 2 DQPSK -91 HT20-14.44 QPSK -83 5.5 CCK -91 HT20-21.67 QPSK -82 11 CCK -88 HT20-28.89 16-QAM -79 6 OFDM -88 HT20-43.33 16-QAM -76 9 OFDM -87 HT20-57.78 64-QAM -72 12 OFDM -85 HT20-65 64-QAM -70 18 OFDM -83 HT20-72.22 64-QAM -67 24 OFDM -81 HT40-15 BPSK -85 36 OFDM -77 HT40-30 QPSK -81 48 OFDM -73 HT40-45 QPSK -79 54 OFDM -70 HT40-60 16-QAM -77 HT40-90 16-QAM -73 HT40-120 64-QAM -69 HT40-135 64-QAM -67 HT40-150 64-QAM -65
CWPL Series 第 11 頁，共 15 頁 4.3 Antenna Specifications Nominal antenna port impedance specification is 50 ohms for the Sony CWPL010 series hardware. For regulatory requirements, it is assumed that the antenna gain is:  Antenna gain for the 2.4GHz band : 1.6dBi There are two antennas supporting 2.4-2.5GHz band. The Sony HD96017 connector will be used on the Sony CWPL010 series hardware. The antenna will be defined Main and Aux where is listing below: Figure 4.1 Two Connector- CWPL010 series Perspective
CWPL Series 第 12 頁，共 15 頁 5. Mechanical Specifications 5.1 Mechanical Drawing Figure 5.1 Two Connector- CWPL010 series mechanical drawing
CWPL Series 第 13 頁，共 15 頁 5.2 RF connector Manufacturer: Sony Manufacturer P/N: HD96017 5.2.1 Specification Operating temperature range: -40℃℃℃℃~90℃℃℃℃ Storage temperature range: -40℃℃℃℃~90℃℃℃℃ Characteristic impedance: 50Ω (0~3GHz) Voltage standing wave ratio: VSWR<=1.3 (0.045~3GHz) 5.2.2 Dimensions: (Unit: mm) Figure 5.2 RF connector dimensions 5.3 Label Specifications Figure 5.3 CWPL0102U Label Drawing
CWPL Series 第 14 頁，共 15 頁 6. Environmental Specifications The following tables provide normal operating conditions and maximum rating requirements for CWPL010 series hardware. Table 6.1 Operating Conditions Environment Limits Operating 0-70℃ ※The radio parts at operating state and above temperature of T-shield. Table 6.2 Non-operating Conditions Environment Temperature Humidity Min. Typ. Max. Unit Min. Typ. Max. Unit Non-Operating -25 25 65 ℃ 45 - 90 % ※ Temperature condition for storage (Packaged) in warehouse is Maximum 40℃ up to 6 months. 7. Part Numbering 7.1 Part Numbering Figure 7.1 Part Numbering
CWPL Series 第 15 頁，共 15 頁 7.2 ID Definitions Table 7.1 ID Definitions WLAN Type Mode PID VID CPWL101UXXX-RT3370 BGN 0x0006 0x0489 8. Regulatory Channel Setting Active Passive Disable FCC Ch1-Ch11 Ch12-Ch13 Ch14
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirement, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:AK8CPWL0102U”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu