Sony Group DRBT1 Bluetooth Earset User Manual GB1U p65

Sony Corporation Bluetooth Earset GB1U p65

User Manual

Operating InstructionsManual de instruccionesBluetooth® EarsetSystem2-186-671-11(1)© 2004 Sony Corporation Printed in KoreaDR-BT1KTHIS PRODUCT IS MANUFACTURED UNDERONE OR MORE OF THE FOLLOWING SONYU.S. PATENTS:4,429,194; 4,736,435; 4,668,842; AND OTHERPATENTS ISSUED OR PENDING IN U.S. ANDOTHER COUNTRIES EnglishOwner’s RecordThe model and serial number are located at the rear ofthe Bluetooth earset and at the belt clip of the Bluetoothearset adaptor.Record these numbers in the spaces provided below.Refer to them whenever you call upon your Sony dealerregarding this product.Model No. DR-BT1KBluetooth earset : DR-BT1Bluetooth earset adaptor : DRC-BT1Serial No.Bluetooth earset:------------------------Bluetooth earset adaptor:------------------WARNINGTo prevent fire or shock hazard, do not exposethe unit to rain or moisture.To avoid electrical shock, do not open thecabinet. Refer servicing to qualified personnelonly.InformationThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received,including interference that may cause undesiredoperation.You are cautioned that any changes or modifications notexpressly approved in this manual could void yourauthority to operate this equipment.Note :This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interfer-ence in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications.However, there is no guarantee that interference will notoccur in a particular installation. If this equipment doescause harmful interference to radio or televisionreception, which can be determined by turning theequipment off and on, the user is encouraged to try tocorrect the interference by one or more of the followingmeasures:–Reorient or relocate the receiving antenna.–Increase the separation between the equipment andreceiver.– Connect the equipment into an outlet on a circuitdifferent from that to which the receiver isconnected.–Consult the dealer or an experienced radio/ TVtechnician for help.This transmitter must not be co-located or operated inconjunction with any other antenna or transmitter.This equipment complies with FCC radiation exposurelimits set forth for uncontrolled equipment and meetsthe FCC radio frequency (RF) Exposure Guidelines inSupplement C to OET65. This equipment has very lowlevels of RF energy that it is deemed to comply withouttesting of specific absorption ratio (SAR).The Bluetooth word mark and logos are owned by theBluetooth SIG, Inc. and any use of such marks bySONY is under license.Nokia is a registered trademark of Nokia Corporation.N Getting startedUnpackingCheck that you have the following items:• Bluetooth earset (1)• Hanger (Size S) (1)R• Bluetooth earset adaptor (1)•AC power adaptor (1)•Car Air-vent clip (1)•Warranty (1)•Operating Instructions (1)IdentifyingBluetooth earsetRL123456781Hanger2Multifunction buttonControls various functions of the Bluetooth earset.3LED indicatorIndicates the status of the Bluetooth earset.4VOLUME +5VOLUME -6Pipe microphone7Housing8Contact terminalBluetooth earset adaptor1345621LED indicatorIndicates the status of the Bluetooth earset adaptor.2Power on button3Pairing / Power off button4Contact pin5Belt clip6DC IN 4.5 V jackCharging the unitsThe Bluetooth earset contains a rechargeable Lithium-Ion battery and the Bluetooth earset adaptor contains aNickel-Metal Hydride battery, which should be chargedbefore using for the first time.1Dock the Bluetooth earset with theBluetooth earset adaptor.2Connect the supplied AC poweradaptor to DC IN 4.5 V jack on theBluetooth earset adaptor.When the AC power adaptor connected to an ACoutlet, both units will turn off automatically.3Make sure that the indicator lights upgreen.Charging is completed in about 2.5 hours* and theindicator goes off.*Time required to fully charge empty battery.Notes•Charge in an environmental temperature of between0˚C and 40˚C (between 32˚F and 104˚F).•Avoid exposure to temperature extremes, directsunlight, moisture, sand, dust or mechanical shock.Never leave in a car parked in the sun.•Use only the supplied AC power adaptor. Do not useany other AC power adaptor.Polarity of the plugRecommended accessoryCar Multi-Voltage DC Adaptor : DCC-E345Buy Sony Accessories at URL :http://www.sony.com/sonyaccessoriesor call 1-888-559-7669 (SONY)Charging and usage hoursIt is usage time from fully charged.Bluetooth Bluetoothearset earset adaptor<DR-BT1> <DRC-BT1>Talk time 7 hours 5 hours(up to)Standby time 160 hours 100 hours(up to)Time stated above may vary, depending on thetemperature or conditions of use.NoteCharge the built-in rechargeable battery or if the LEDindicator is still off after charging the built-inrechargeable battery, take the Bluetooth earset andBluetooth earset adaptor to a Sony dealer for replace-ment of the rechargeable battery.To DC IN 4.5 jackAC power adaptor(supplied)To an AC outletBoth indicators lightup greenFor the customers in the USA– Recycling of battery in Bluetooth earsetRECYCLING LITHIUM-ION BATTERIESLithium-Ion batteries arerecyclable. You can helppreserve our environment byreturning your usedrechargeable batteries to thecollection and recycling locationnearest you.For more information regarding recycling ofrechargeable batteries, call toll free1-800-822-8837, or visit http://www.rbrc.org/Caution:Do not handle damaged or leaking Lithium-Ionbatteries.–Recycling of battery in Bluetooth earsetadaptorRECYCLING NICKEL METAL HYDRIDEBATTERIESNickel Metal Hydride batteriesare recyclable. You can helppreserve our environment byreturning your usedrechargeable batteries to thecollection and recycling locationnearest you.For more information regarding recycling ofrechargeable batteries, call toll free1-800-822-8837, or visit http://www.rbrc.org/Caution:Do not handle damaged or leaking Nickel MetalHydride batteries.Welcome!Thank you for purchasing the Sony DR-BT1KBluetooth earset system. Before operating the unit,please read this manual thoroughly and retain it forfuture reference.Some features are:•Wireless system that allows you to talk by mobilephone.•Car Air-vent clip for car use.•Fits on either your right or left ear.•Convenient earset adaptor with belt clip• Up to 5 hours for talking. Up to 100hours for standby.•Flexible pipe microphone.•Volume control function on the earset.What's Bluetooth?Bluetooth is a new technology that enables wireless datacommunication by mobile phones, computers or othermobile devices.Bluetooth wireless technology operates within a rangeof about 10 meters* (about 30 feet).*Obstacles (body, metal, wall etc.) or receptionconditions may adversely affect the usable range.Notes•The communication with Bluetooth wirelesstechnology may be affected by the conditions below.–Obstacles between the Bluetooth earset and theBluetooth earset adaptor or mobile phones withBluetooth wireless technology: Body, metal, walls, etc.–Electromagnetic waves: A place where a wireless LAN is installed, amicrowave oven is used, or where electromagneticenergy exists•The above is also subject to the mobile phone’santenna and reception conditions.
DTo callTake the calling, finish the talking ordial by operating the mobile phone.If your mobile phone equipped with voice-dialfunction, you can dial by the pipe microphone.ETo discommunicate of the unitsPress the Multifunction button once.SCO LINK disconnects. The Bluetooth earset andthe Bluetooth earset adaptor return to the standbymode.To shut down the unitsFTo shut down the BluetoothearsetHold down the POWER/TALK buttonon the Bluetooth earset until LEDturned off.GTo shut down the Bluetoothearset adaptorHold down the Pairing/Power offbutton with the point of the plug orsimilar instrument until LED turnedoff.When the telephone isreceivedPress your mobile phone buttons.There is a mobile phone that can receive pressingthe POWER/TALK button.To adjust the volumePress the VOLUME + or – while SCO Link.The beep of current volume is heard every time bypressing each button.When the volume setting is maximum or minimum, thebeep does not sound for the exceeded operations.N Operating the systemWearing the headset1Hook the Bluetooth earset aroundyour ear, as you would glasses.2Adjust the position of the Bluetoothearset to fit comfortably.Changing the direction ofthe hangerThis unit can be worn on the right or left ear by thefollowing procedure.1Holding the housing firmly, unlatchthe hanger assembly.RL2Holding the housing, rotate thehanger, and then pull out in thedirection of the arrow.LR gLRTipThe unit comes with 2 hanger sizes to ensure acomfortable fit.LR3Turn the hanger around as illustratedbelow, and attach in the direction ofthe arrow.LL4Rotate the housing.RLLNoteThe housing and the hanger are marked left (L) andright (R). For example, when using the left ear, thehousing is set in the L position, and the hanger isattached with the L mark visible.Operating the unitsGeneral operation flow is described as follows:To shut down the unitsTo change into a standby modeThe mobile phone provided function may notcorrespond. Refer to the manual supplied with yourmobile pone.To change into a standbymodeATo prepare the Bluetooth earsetHold down the Multifunction buttonon the Bluetooth earset about 7seconds.When the LED blinks fast blue, release the button.The LED becomes to blink slowly blue.NoteTake care that if the Maltifunction button hold downabout 10 seconds, the status goes pairing mode.BTo prepare the Bluetooth earsetadaptor1Press the POWER ON button a fewseconds.When the LED lights up blue and green, after theLED becomes to blink slowly blue.2Connect the Bluetooth earset adaptorto your mobile phone.If there are not obstacles between the Bluetooth earsetand the Bluetooth earset adaptor, the communicationsensitivity goes up.CTo communicate of the units(SCO LINK)Press the Multifunction button.The Bluetooth earset and the Bluetooth earsetadaptor start communication (SCO LINK), so thatthe sound from mobile phone is heard by theBluetooth earset.And the voice talking by the pipe microphone istransmitted to the mobile phone.When the SCO LINK has been started, the LED onBluetooth earset adaptor lights up green, then thatblinks blue.The LED on Bluetooth earset blinks 3 times blue.VOLUME + VOLUME -How to use the carattachmentThe car attachment (supplied) can be used hold theBluetooth earset adaptor, by installing it in the vent ofthe air conditioner of your car.It is convenient for charging/using while driving.Standard installationHorizontal fin9 mm (min)7 mm (min)17 mm (min)3 mm (min)Vertical fin17 mm (min)9 mm (min)7 mm (min)3 mm (min)2.5 mm tripepolarity jackPairing the unitsTo pair Bluetooth earset with Bluetooth earsetadaptorThe Bluetooth earset and Bluetooth earset adaptor comealready paired from factory. To pair the Bluetooth earsetand Bluetooth earset adaptor again after use, do thefollowing.1Place the Bluetooth earset and theBluetooth earset adaptor closetogether, as illustrated.1m*2While the Bluetooth earset is turnedoff, hold down the Maltifunctionbutton.The LED will blink in blue for the first 7 seconds(approx.). Keep pressing until the LED blinks blueand green.3Press the Power on button on theBluetooth earset adaptor.4Hold down the Pairing / Power offbutton with the point of the plug orsimilar instrument (for about 3seconds) until the LED lights up blueand green.After a few seconds, both units the blue/greenblinking will change to blink only blue, indicatingStandby mode.NoteTime out for pairing mode is as follows:The Bluetooth earset : about 60 seconds.The Bluetooth earset adaptor : about 20 seconds.To pair Bluetooth earset with a mobile phonefor Bluetooth wireless technologyThe Bluetooth earset can pair directly a mobile phonewith Bluetooth wireless technology. Do the following.1Place the Bluetooth earset and themobile phone close together within1 m.2Repeat above step 2.See “To pair Bluetooth earset with Bluetoothearset adaptor”.3Search the Bluetooth earset by themobile phone.If the mobile phone detects the Bluetooth earset,“DR-BT1” will appear in the display of the mobilephone.4Select “DR-BT1” in the list, then inputthe passkey* (0000).After a few seconds, the setting is completed.*Passkey may also be called the following.– Pass code, PIN code, PIN number, Password.NoteRefer to the manual supplied with your mobile phone.
To install the carattachment1Attach the hook to the rear of theattachment. Ensure it is the correctway round. (See illustration)2Attach the spacer under the hookfirmly after peeling off the double-faced tape.3Insert the hook in the vent of the airconditioner. Confirm the hook isfirmly clipped to the fin.4Dock the Bluetooth earset adaptor’sbelt clip in the attachment.Tips•Use the other hook (L) if the air conditioner is sloped.•You can adjust the inclination of the attachment bysliding the rear of the car attachment.•Install the hook to face side ways if the fin of the airconditioner is vertical. g To remove the attachment1Push the car attachment back, andpush gently it off the fin.2Remove the attachment whilesuppressing the fin.NoteIf the attachment is pulled out and catches the fin, itmay damage it.SpacerN Additional informationDisposing of theBluetooth earset andadaptorFor environmental conservation, be sure to remove thebuilt-in rechargeable battery from the units before youdispose of them, and dispose of the battery appropri-ately.In the case of theBluetooth earset1Remove the two screws from the rear.RL2Push hard around the arrow asillustrated to unlatch the unitassembly.3Lift lightly by the pipe microphone.4Remove each XXX first, and thenremove the battery from the XXX.5Remove the connector.In the case of theBluetooth earset adaptor1Remove the screw from the rear.2Raise the cover by the belt clip.3Remove the connector.4Pull out the battery.NoteBe careful not to touch the circuit board attached to thebattery box. Hold the battery box (black plastic box)when you remove them.Precautions•Do not leave the Bluetooth earset system in a locationsubject to direct sunlight, heat or moisture.•Consult local lows and regulations regarding use ofthe Bluetooth earset while driving or cycling.• Using the Bluetooth earset may not functiondepending on radio wave conditions and locationwhere the equipment is being used.•If you experience discomfort after wearing the earset,take off the Bluetooth earset immediately.•Start dialing after connecting the Bluetooth earset toyour mobile phone.Notes on earsetPreventing hearing damage avoid using earset at highvolume. Hearing experts advise against continuous, loudand extended play. If you experience a ringing in yourears, reduce the volume or discontinue use.Caring for othersKeep the volume at a moderate level. This will allowyou to hear outside sounds and to be considerate to thepeople around you.If you have any questions or problems concerning thesystem that are not covered in thismanual, please consult the nearest Sony dealer.Be sure to bring the Bluetooth earset and the Bluetoothearset adaptor to the Sony dealer when requiring repairwork.SpecificationsDR-BT1GeneralBluetooth Compliance:Bluetooth standard Ver. 1.1Output power: Bluetooth standard Power Class2( 2.5mW )Frequency band:2.4GHz band ( 2.4000GHz -2.4835GHz )Max. Communication range:Line of sight approx. 10mSupplied accessory:AC adaptor (1), Hanger (S) (1),Car Air-vent clip (1)Bluetooth earset DR-BT1Supported Bluetooth Profiles:Headset Profile, Hands-free ProfilePower source: DC 3.7V: Built-in Li-ionrechargeable batteryTypical Talktime: 7 hoursTypical Standby Time:160 hoursMass: Approx. 20gReceiverType: Open air, dynamicDriver unit: 13.5mm dome type (CCAWVoice Coil)Sensitivity: 104dB/mWImpedance: 16Ω at 1kHzPower handling capacity:50mW(IEC)Reproduction frequency range:50-20,000HzMicrophoneType: Flexible pipe microphoneUnit: Electric condenserOutput impedance: Under 2.2kΩOpen circuit voltage level:-42dB(0dB = 1V/Pa)Effective frequency range:100 - 5,000HzBluetooth earset adaptor DRC-BT1Supported Bluetooth Profiles:Headset ProfilePower source: DC 1.2V: Built-in Ni-MHrechargeable batteryTypical Talktime: 5 hoursTypical Standby Time:100 hoursCord: 0.20m (Max. stretch length 0.7m)Plug: 2.5mm triple/four-pole plugMass: Approx. 35g (without cord)Design and specifications are subject to change withoutnotice.SolutionTurn on the transmitter first, then puton the headphones.Check the connection of the audio/video equipment or the AC poweradaptor.Check that the audio/video equipmentis turned on.Turn up the volume on the connectedaudio/video equipment, if thetransmitter is connected to theheadphones jack.DR-BT1:Change the radio frequency with theCHANNEL selector on the transmitter,then tune the headphones with theTUNE control.DR-BT1:Change the radio frequency with theCHANNEL selector on the transmitter,then press the TUNE button again.The mute function is activated.Use the headphones near the transmit-ter.The headphones’ POWER indicatorlight is weak or turned off.• Charge the supplied rechargeablebatteries or if the POWER indicator isstill off after charging the suppliedrechargeable batteries, take theheadphones to a Sony dealer forreplacement of the rechargeablebattery.If you connect the transmitter to theLINE OUT or REC OUT jacks of anaudio reproducer, make sure that theNOISE FILTER switch is set to OFF.Make sure that the NOISE FILTERswitch is set to either ON or OFF (Ifthe switch gets stuck between ON andOFF, the sound will be cut off).TroubleshootingProblemNo sound/Muffled sound

Navigation menu