Sony Group DTPT1001 PSP Development Tool User Manual DTP T1000 A

Download:
Mirror Download [FCC.gov]
Document ID	544947
Application ID	DiYJzb0iWOWgnbHT6xw6Lg==
Document Description	Manual 1000
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	152.93kB (1911679 bits)
Date Submitted	2005-05-23 00:00:00
Date Available	2005-05-23 00:00:00
Creation Date	2005-02-10 05:16:39
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2005-02-10 17:40:50
Document Title	DTP-T1000 A
Document Author:	Sony Computer Entertainment Inc.

Development Tool
Instruction manual
SCE CONFIDENTIAL
This manual contains safety precautions for the prevention of accidents,
and instructions for the use and handling of this product.
Read this manual carefully and use the product in a safe manner. After
reading the manual, store it in an accessible location for future reference.
DTP-T1000 A
2-515-713-13(1)
WARNING
WARNING
To avoid electrical shock, do not
open the cabinet. Refer servicing to
qualified personnel only.
Use the supplied AC adaptor only. If
you use other types, it may cause fire,
electrical shocks or a malfunction.
Laser specifications
UMDTM
Wave length:
Power:
Type:
DVD-ROM
Wave length:
Power:
Type:
655-665 nm
max 0.28 mW
Semiconductor, continuous
640-660 nm (DVD)
775-805 nm (CD)
max 0.3 mW (DVD)
0.23 mW (CD)
Semiconductor, continuous
For customers in the U.S.A. and Canada
CAUTION
The use of optical instruments with this product will
increase eye hazard. As the laser beams used in the DVDROM and UMD™ drives are harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
FCC Radio-Frequency Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20 cm between the radiator and body. This
transmitter must not be co-located or operating in
conjunction with any antenna or transmitter.
Owner’s Record
The model and serial numbers are located on the side of the
unit. Record the serial number in the space provided below.
Refer to these numbers whenever you call for technical
assistance at the number shown in "Contact information" on
the back cover of this instruction manual.
Model No. DTP-T1000 A
Serial No.______________
For customers in Canada
This Class A digital apparatus complies with Canadian
ICES-003.
The term “IC” before the equipment certification number
only signifies that the Industry Canada technical
specifications were met.
Operation is subject to the following two conditions; (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may
cause undesired operation of the device.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Le terme “IC” avant le numéro d’homologation ne signifie
seulement que les normes d’Industrie Canada ont été
respectées.
This label is located on the DVD-ROM laser protective
housing inside the enclosure.
For customers in the U.S.A.
CAUTION
Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial enviroment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
WARNING
L'utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de
brouillage et (2) l'utilisateur du dispositif doit être prêt à
accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le
fonctionnement du dispositif.
WARNING
For customers in Europe
For customers in Korea
CAUTION
The use of optical instruments with this product will
increase eye hazard. As the laser beams used in the DVDROM and UMD™ drives are harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
This label is located on the DVD-ROM laser protective
housing inside the enclosure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER product marking is located on the side
of the product.
This equipment complies with EN55022 CLASS B and
EN55024 for use in the following areas: residential,
business, and light-industrial.
This equipment has been tested and found to comply with
the limits set out in the R&TTE Directive using a connection
cable shorter than 3 metres.
Audio and picture distortion may occur if this equipment is
positioned in close proximity to any equipment emitting
electromagnetic radiation.
If this unit is affected by static electricity or burst-noise, it
may not work correctly.
Dit apparaat bevat een vast ingebouwde batterij die niet
vervangen hoeft te worden tijdens de levensduur van het
apparaat. Raadpleeg uw leverancier indien de batterij toch
vervangen moet worden. De batterij mag alleen vervangen
worden door vakbekwaam servicepersoneel.
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Lever het apparaat aan het einde van de levensduur in voor
recycling, de batterij zal dan op correcte wijze verwerkt
worden.
0412
WARNING
Important safeguards
For your protection, please read these
safety instructions completely before
operating the appliance, and keep this
manual for future reference.
Water and moisture
Carefully observe all warnings,
precautions and instructions on the
appliance, or those described in the
instruction manual and adhere to them.
Do not use the powerline operated unit near water –
for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement or near a
swimming pool, etc.
INSTALLATION
Power cord protection
USE
Power sources
This unit should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of electrical power supplied
to your home, consult your dealer or local power
company. For those units designed to operate from
battery power, or other sources, refer to the
operating instructions.
Overloading
Do not overload wall outlets, extension cords or
convenience receptacles beyond their capacity,
since this can result in fire or electric shock.
Liquid and foreign objects
Never push objects of any kind into the unit through
openings as they may touch dangerous voltage
points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the
unit.
Attachments
Do not use attachments not recommended by the
manufacturer, as they may cause hazards.
Cleaning
Unplug the unit from the wall outlet before cleaning
or polishing it. Do not use liquid cleaners or aerosol
cleaners. Use a cloth lightly dampened with water
for cleaning the unit exterior.
Important safeguards
Route the power cord so that it is not likely to be
walked on or pinched by items placed upon or
against it, paying particular attention to the plugs,
receptacles, and the point where the cord exits from
the unit.
Ventilation
The slots and openings in the cabinet are provided
for necessary ventilation. To ensure reliable
operation of the unit, and to protect it from
overheating, these slots and openings must never be
blocked or covered.
– Never cover the slots and openings with a
cloth or other materials.
– Never block the slots and openings by placing
the unit on a bed, sofa, rug or other similar
surface.
Accessories
Do not place the unit on an unstable cart, stand,
bracket or table. The unit may fall, causing serious
injury to a child or an adult, and serious damage to
the unit.
Use only a cart, stand, tripod, bracket, or table
recommended by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
– Never place the unit in a confined space, such
as a bookcase, or built-in cabinet, unless
proper ventilation is provided.
– Do not place the unit near or over a radiator or
heat register, or where it is exposed to direct
sunlight.
Important safeguards
SERVICE
Damage requiring service
Unplug the unit from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
– When the power cord or plug is damaged or
frayed.
– If liquid has been spilled or objects have fallen
onto the unit.
– If the unit has been exposed to rain or water.
– If the unit has been subject to strong physical
shock by being dropped, or the cabinet has
been damaged.
– If the unit does not operate normally when
following the instruction manual. Adjust only
those controls that are specified in the
instruction manual. Improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the unit to normal
operation.
– When the unit exhibits a distinct change in
performance – this indicates a need for service.
Servicing
Do not attempt to service the unit yourself as
opening or removing the exterior casing may expose
you to dangerous voltage or other hazards.
Refer all servicing to an authorized service center.
Refer to the contact information on the back cover
to receive instructions on obtaining repair/
replacement services.
Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original parts.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
Safety check
Upon completion of any service or repairs to the
unit, ask the service technician to perform routine
safety checks (as specified by the manufacturer) to
determine that the unit is in safe operating
condition.
Important safeguards
Table of contents
WARNING ................................................................................. 2
Important safeguards ............................................................. 4
Precautions .............................................................................. 7
Chapter 1
Overview
About this product .................................................................. 9
Part names and usage .......................................................... 10
System configuration example ............................................ 14
Chapter 2
Preparing to use
the unit
Connecting to a network ...................................................... 15
Unit or accessories necessary for connecting ....................... 15
Connection diagrams ............................................................ 15
Connecting peripherals ......................................................... 16
Setting up ............................................................................... 17
Information necessary for setup ........................................... 17
Preparing for setup ............................................................... 17
Turning on the unit ............................................................... 17
Confirming information settings .......................................... 18
Starting the Administration Tool .......................................... 18
Setting up .............................................................................. 19
Showing status ...................................................................... 24
Usage notice ......................................................................... 25
Chapter 3
Appendices
Table of contents
Troubleshooting .................................................................... 26
Specifications ........................................................................ 28
R&TTE Directive "Informal DoC" statement ....................... 29
Limitations of liability ........................................................... 30
Precautions
Safety
Use and handling
• Do not use the unit or accessories outdoors.
• Do not throw or drop the unit or accessories, or expose the devices to strong physical shock. Handle
the analog stick with care.
• Do not forcibly twist the controller or expose it to strong physical shock, as doing so can cause
damage.
• Do not place the unit or accessories on surfaces that are unstable, tilted or subject to vibration.
• Do not expose the unit or accessories to high temperatures, high humidity or direct sunlight.
• Do not block the vents.
• Do not wrap the unit or accessories in cloth or similar materials.
• Do not allow dust to build up on the unit.
• Do not place the unit in locations of poor ventilation, such as small, enclosed areas, directly against a
wall or on a thick carpet or bedding.
• Do not expose the unit to dust, smoke or steam.
• Do not allow liquid or small particles to get into the unit.
• Do not put heavy objects on the unit.
• Do not place anything in front of the disc tray.
• Do not use damaged, reshaped or repaired discs.
• Do not touch or insert foreign objects into the connectors of the unit or accessories.
• Do not insert cords and cables at an angle. Doing so may damage the connector pins or create the risk
of fire.
• Do not set the unit other than in the vertical position.
• If a spring or screw is provided to secure a cable connector, use the provided spring or screw to secure
it. Take care to prevent making faulty connections.
Precautions
Overview
This product has been designed with the highest concern for safety. However, any electrical device, if
used improperly, has the potential for causing fire, electrical shock or personal injury. To help ensure
accident-free operation, follow these guidelines.
• Observe all warnings, precautions and instructions.
• Stop use and unplug the AC power cord from the electrical outlet if the unit functions in an abnormal
manner, or produces unusual sounds or smells.
• Call the number listed on the back cover for technical assistance if the device does not operate
properly.
• Do not remove the unit’s exterior or disassemble the unit. The laser beam emitted from the lens of this
unit may be harmful to the eyes.
• Do not use the unit near water.
• Stop using the unit immediately if you experience any of the following symptoms. If the condition
persists, consult a doctor.
– Lightheadedness, nausea or a sensation similar to motion sickness
– Tired, uncomfortable or aching hands or arms
– Tired, dry or aching eyes
• Avoid looking at the screen for prolonged periods of time.
• Listening to sound continuously for a long time with a high volume may adversely affect the ears. Be
careful, especially when using headphones. Adjust the volume so that surrounding sounds can be
heard.
• Do not close the disc tray or disc cover in a way that could pinch your hand or fingers, as personal
injury or damage to the unit could result.
• The socket outlet shall be installed near the equipment and shall be easily accessible.
Precautions
AC adaptor and AC power cord use
Overview
• To help ensure safe operation, during initial setup and regularly thereafter, inspect the AC adaptor and
AC power cord. If damaged, stop use immediately and call the number on the back cover for assistance.
• Do not use AC adaptors or AC power cords other than those provided or designated in the instruction
manual. If the provided or designated AC adaptor or power cord is not used, electrical shock may
result or the unit may not operate.
• Do not modify or damage the AC power cord.
• Do not place the AC adaptor between the unit and a wall or shelf.
• Do not place heavy objects on the AC power cord.
• Check that there is no dust or lint on the power plug before inserting into an electrical outlet. If the
plug becomes dirty, wipe it off with a dry cloth before connecting.
• When inserting the AC power cord into an electrical outlet, insert the plug straight into the electrical
outlet and not at an angle.
• Unplug the AC power cord from the electrical outlet before cleaning or moving the unit, or when you
do not intend to use the unit for an extended period of time. When disconnecting, grasp the power cord
by the plug and pull straight out of the electrical socket. Never pull by the cord and do not pull out at
an angle.
• Do not touch the plug of the AC power cord with wet hands.
• Do not touch the power plug during an electrical storm.
• Do not touch the unit or AC adaptor for extended periods of time while the unit is turned on, as
extended contact may cause low-temperature burns.
Cleaning
• For safety reasons, before cleaning the unit or connected accessories, 1) turn off the unit, 2) disconnect
the power plug for the unit from the electrical outlet.
Moisture condensation
• If the unit or disc is brought directly from a cold location to a warm one, moisture may condense on
the lens inside the unit or on the disc. Should this occur, the unit may not operate properly. In this case,
remove the disc and turn off and unplug the unit. Do not put the disc back in until the moisture
evaporates (this may take several hours). If the unit still does not operate properly, obtain technical
assistance using the contact information on the back cover.
Photosensitivity
• A very small percentage of individuals may experience epileptic seizures when exposed to certain light
patterns or flashing lights. Exposure to certain patterns or backgrounds on a television screen or while
playing video games, including games played on the unit, may trigger an epileptic seizure in these
individuals. Certain conditions may trigger previously undetected epileptic symptoms even in persons
who have no history of prior seizures or epilepsy. If you, or anyone in your family, has an epileptic
condition, consult your physician prior to playing. If you experience any of the following symptoms
while playing a video game - dizziness, altered vision, eye or muscle twitches, loss of awareness,
disorientation, any involuntary movement or convulsions - IMMEDIATELY discontinue use and
consult your physician before resuming play.
Radio waves
• Radio waves may affect electronic equipment or medical devices (for example, pacemakers), which
may cause malfunctions and possible injuries.
- If you use a pacemaker or other medical device, consult your physician or the manufacturer of your
medical device before using the wireless networking feature.
- Keep the unit at least 9 inches (23 cm) away from a pacemaker or other medical devices when using
the wireless networking feature.
Precautions
1
Chapter
About this product
This unit is equipped with features for the development of PSPTM software.
The unit can download software or data from a local area network, allowing for the efficient debugging,
running and checking of programs.
• PSPTM features are provided for efficient software development.
• A built-in communication processor allows software, data etc. to be easily sent and received through
the development PCs and networks.
• A direct network connection can be established for easy installation and additions. Also, the load on
development PCs can be reduced.
• Two types of drives are built in: a UMDTM drive, and a DVD-ROM drive, which is used during
development. A switch is used to select the desired drive.
For proper operation, separate development software and a development PC are required.
For details, contact technical support using the contact information on the back cover.
About this product
Overview
Overview
Part names and usage
Unit front
• Press the on/standby button and hold it down
for three seconds. The power indicator will
flash and then turn orange, at which point the
power will be turned off (and the system will
enter standby mode).
• Remove the power plug from the electrical
outlet after the power indicator turns a solid
orange. If the plug is removed before the
indicator turns orange, failure of the unit may
result.
UMD
DRIVE SELECT
DVD
POWER
Overview
Turning the unit off (standby mode)
SYSTEM INIT
q;
NETWORK INIT
CONTROLLER
qa
GPO
qd
qs
qf
GPI
ON OFF
qg
qh
1 On/standby button, power
indicator
This button turns the unit on and off.
To turn on the unit
Press the on/standby button while it is in standby
mode. The power indicator flashes green as the
power turns on. The indicator then turns solid
green when the system is ready. The system
status can be determined by the color and status
of the power indicator.
Flashing green
The system is preparing to
start up (flashes until the
system becomes available
after the on/standby button
is pressed)
Solid green
The system is starting up
(the unit can now be used)
Flashing red
During system initialization
(auto-recovery)
Solid red
System initialization or
update failure (indicates the
need to initialize the
system)
Flashing orange
During network initialization
Solid orange
Standby mode
10
Part names and usage
2 Disc cover
The open button (3) is used to open the cover
so that UMDTM can be inserted. When closing,
press the middle of the upper edge of the disc
cover.
3 Open button
This button is used to open the disc cover (2).
4 Memory Stick DuoTM access
indicator
Turns orange while the unit is accessing a
Memory Stick DuoTM or Memory Stick PRO
DuoTM that has been inserted into the unit.
5 Memory Stick DuoTM slot
This slot accepts Memory Stick DuoTM or
Memory Stick PRO DuoTM media.
6 USB connector
For connecting USB connectors (mini-B type).
When the included controller is connected to the
USB connector, the controller’s USB connector
becomes functional.
7 Drive select button
Switches between the UMDTM drive and the
DVD-ROM drive.
The selected drive is identified by the UMDTM/
DVD-ROM drive indicators (8). The drive
select button (7) can be used only when the
power indicator of the controller is not lit.
8 UMDTM/DVD-ROM drive indicator
The indicator for the drive, UMDTM or DVDROM, turns orange to indicate which drive is
selected.
9 Open/close button
This button is used to open/close the DVD-ROM
drive.
Part names and usage
qd Controller port
Connects with the commander interface
connector of the attached controller.
qf GPO indicator
These are eight indicators that are user-definable
by PSPTM software developers.
qg Headset connector
A dedicated PSPTM headset remote controller or a
commercially sold headset (with a stereo miniplug) can be connected here.
qh GPI switch
These are eight dip switches that are userdefinable by PSPTM software developers.
Unit rear
1 Aerial
For wireless LAN use.
2 Extension connector
For use by service personnel only.
3 Dedicated connector for servicing
For use by service personnel only.
Caution
EXT
Usage of this port may cause irreparable damage to the
system.
RF (EXT)
q;
5 Network connector
Connector for a network cable. Allows
connection to a local area network.
qa
6 VGA connector
Connects to a device with a VGA IN connector.
FOOT SW
DC IN
19.5V
AUDIO
OUT
4 Foot switch connector
Connects to the supplied foot switch.
7 AUDIO OUT connector
Connects to a device with an AUDIO IN
connector.
8 Vent fan
Vent for internal fan used to cool unit. Be sure
not to obstruct this vent, as doing so may cause a
fire. Also, to prevent any hindrance to air flow,
position the unit an adequate distance from walls.
Part names and usage
11
Overview
q; System initialise button
While holding down this button, pressing the
on/standby button (1) returns the
communication processor software to the factory
default initial state.
qa Network initialise button
While holding down this button, pressing the
on/standby button (1) restores the factory
default values for the IP address settings.
qs DVD-ROM drive
This drive accepts DVD-ROM discs. Use the
open/close button (9) to insert and remove
discs.
Part names and usage
9 RF (extension) connector
Connects to an access point using a coaxial cable.
qa DC IN 19.5V connector
For attaching the included AC adaptor.
Overview
q; Clamp
For securing the aerial and
AC adaptor to the unit.
Controller front
POWER
q;
qa
qs
HOLD
HOME
VOL
SELECT
START
qd
qf qg qh
qjqkqlw;
1 LCD screen
qa Strap holder
2 L button
qs Left speaker
3 R button
qd Right speaker
4 Up, down, left, right buttons
qf Home button
5 △, ○, ×, □ buttons
qg Volume - button
6 Power indicator
qh Volume + button
qj Display button
7 Hold indicator
8 Memory Stick Duo
indicator
TM
access
9 WLAN access indicator
q; Analog stick
12
Part names and usage
qk Sound button
ql Select button
w; Start button
Part names and usage
Controller front
Overview
1 IR port
2 USB connector
Controller bottom
1 Left speaker
2 Right speaker
Caution
Do not cover or insert foreign objects into the speakers as doing so may result in damage to the controller.
Controller left
Controller right
1 WLAN switch
1 Power/hold switch
Caution
For this product, the debugger (dstdb) reset command cannot
be used when the power/hold switch of the controller is in the
hold position. Make sure that the controller's power/hold
switch is not in the hold position when operating the
debugger.
Part names and usage
13
System configuration example
The following accessories may be connected to the unit.
To UMD
TM
drive
USB device
TM
UMD
To Memory Stick Duo
slot
DRIVE SELECT
To USB connector
DVD
POWER
Overview
Unit front
SYSTEM INIT
To USB
connector
NETWORK INIT
CONTROLLER
To DVD-ROM drive
GPO
POWER
HOLD
HOME
SELECT
VOL
START
To controller port
GPI
ON OFF
To headset
connector
Headset
remote controller
Caution
When you connect or disconnect the controller, turn off power to the unit (keep it in standby mode). If the power is left on, it may
result in damage to the unit or the controller.
Unit rear
Before connecting a cable, rotate the
aerial in a clockwise direction, and raise it
upright. If the cable is connected first, it
may not be possible to rotate the aerial.
EXT
To RF (extension)
connector
RF (EXT)
Foot switch
To foot switch
connector
Wireless LAN
access point
To network connector
FOOT SW
Hub
Monitor
DC IN
19.5V
To VGA connector
AUDIO
Speaker
To AUDIO OUT
connector
14
System configuration example
OUT
Development PC
2
Chapter
Connecting to a network
The unit
Unit or accessories
necessary for connecting
The following devices and accessories are
necessary in order to use this unit as a
development machine:
• Development Tool
• Network cable
• Hub
• Development PC
Connection diagrams
Before connecting a cable, rotate the aerial in a
clockwise direction, and raise it upright. If the
cable is connected first, it may not be possible to
rotate the aerial.
Connecting to a network without a
DHCP server
You can build a local network with this unit and
a development PC in the following manner.
Hub
Controller
Development PC
At this time, the following static IP addresses are
automatically set for the unit:
• IP address : 192.168.0.10
• Subnet mask : 255.255.255.0
Caution
• The IP address and subnet mask settings are default factory
settings. When the network settings for the unit are
modified, these settings are also modified accordingly.
• To modify the IP address, start up both the unit and the
development PC, and configure their respective settings to
support the network to which they are to be connected.
After configuration, use a network cable to connect the unit
and the development PC to a hub within the network in use.
Refer to “Setting up” on page 17 for infomation on how to
set up the unit.
Connecting to a network
15
Preparing to use the unit
Preparing to use
the unit
Connecting to a network
Connecting to a network with a DHCP
server
When using the unit in Europe,
Oceania and Korea
Connect the unit and a development PC running
the DHCP client software to a hub on the
network.
Install the supplied RFI filter on the network
cable (unshielded twisted pair cable). Install the
RFI filter near the main unit.
Preparing to use the unit
Network
The unit
Hub
When installing the RFI filter on the cable, wind
the cable once around the RFI filter, as shown
below.
There is a band supplied for use with the RFI
filter. Use the band to attach the RFI filter to the
cable. Fit the band to the cable, as shown below.
Monitor
Controller
Development PCs
cable
Install near the unit
In this case, the IP address and subnet mask
settings will be obtained automatically when the
unit is turned on. Depending on the settings of
the DHCP server, other network settings, such as
the DNS server and default gateway, may also be
obtained. For details on which settings can be
automatically obtained, contact your network
administrator.
Connecting peripherals
Connect the unit to a hub using a
network cable.
Connect the hub to the development
PC using a network cable.
Caution
When using the wireless LAN function, keep the controller
away from the unit’s aerial. If the unit is used with the
controller and aerial in close proximity, radio frequency
interference from the controller can affect the radio waves of
the wireless LAN.
16
Connecting to a network
RFI filter
Cut after fitting
Band
Setting up
Information necessary for
setup
The following information is required for the
setup of the unit.
Connecting to a network with a DHCP
server
Turn on the development PC.
Configure the DHCP server.
When the IP address is automatically
obtained by the DHCP server, the specific IP
address allotted to a device is generally
different each time the device is connected to
the network. However, the use of the unit can
be made more convenient by setting the same
IP address to be allotted each time the device
is connected. Contact your network
administrator for details on how to set a static
IP address.
• DHCP server availability
• IP address
• Subnet mask
• IP address of the default gateway
Check with your network administrator about the
structure of the network to which this unit will be
connected.
Preparing for setup
Before setting up the unit, you need to configure
your development PC.
Connecting to a network without a
DHCP server
Turn on the development PC.
Configure the TCP/IP settings of the
development PC.
Configure the TCP/IP settings as follows:
• IP address of the development PC
192.168.0.2
• Subnet mask of the development PC
255.255.255.0
Activate the Web browser on the
development PC, and configure it so that it
does not use a proxy.
Refer to the development PC’s instruction
manual for details.
Configure the development PC.
Run the DHCP client software and configure
it so that the development PC can obtain the
IP address and other settings from the DHCP
server. Refer to the instructions supplied with
the development PC for details on how to
configure the PC to run the software and
obtain an IP address. Next, configure the
development PC to run a Web browser.
Turning on the unit
After configuring the TCP/IP settings of the
development PC, turn on the unit.
Connect the AC power cord to the AC
adaptor, then connect the AC adaptor
to the unit.
Insert the AC power cord into an
electrical outlet.
The power indicator turns orange, and the
unit enters standby mode.
Press the on/standby button.
This turns on the unit and starts system
initialization. During initialization, the power
indicator flashes green. This indicator stops
flashing when initialization is complete.
Caution
• When turning on the unit, be sure to use the supplied AC
adaptor.
• Do not operate the unit during initialization.
Setting up
17
Preparing to use the unit
Setting up
Confirming information
settings
Login
Log in with a user name and password.
Confirm that the information below is displayed
on the controller LCD:
Preparing to use the unit
• IP Address
• Subnet mask
• Broadcast address
• IP address of the default gateway
• Mac address
• Host name
Caution
When you connect or disconnect the controller, turn off
power to the unit (keep it in standby mode). If the power is
left on, it may result in damage to the unit or the controller.
Enter the user name and password.
Starting the Administration
Tool
• user name: Administrator
• password: Administrator
* These are the factory default settings.
Start up the Administration Tool on the
development PC. The following section assumes
use of the IP address 192.168.0.10 for the unit.
Enter the user name and password as
follows.
To log in as the administrator, enter the
“Administrator” user name and password as
follows:
When logged in as the administrator, all of
the functions shown in the Administration
Tools menu are active.
Start the Web browser on the
development PC.
To log in as a user, enter the user name and
password as follows:
Type “http://192.168.0.10/” and press
the “Enter” key.
The language selection screen is displayed.
• user name: User
• password: User
* These are the factory default settings.
When logged in as a user, only the “Status
Display” functions shown in the
Administration Tools menu are active. The
“Settings” functions cannot be used.
Select the display language for the
administration tool.
The login screen is displayed.
Select the language (for example English) here.
18
Setting up
Click [OK].
Upon successfully logging in, the main
screen of the Administration Tool is
displayed.
Setting up
Setup
These options allow the user to modify settings,
update the software and shut down the unit.
Change the administrator
password
User password
Change the user password
Date & time
Configure the time and time
zone
Shutdown
Reboot/Shutdown
Network
Configure the necessary
network settings
Access control
Configure dsnet access
control
Reset of setting
Initialize the selected
settings
Save & load
Save settings, and
synchronize the saved
settings with this unit
Update
Update the system
Restart of dsnetm
Restart programs
communicating with the
host PC
Self-diagnostic
program
Conduct a variety of tests
Setting up
Click on the items to the right of “Setup” to
configure each setup.
Preparing to use the unit
Administrator
password
Online help
You can view the Help for the Administration
Tool.
Administrator password
Upon clicking “Administrator password”, the
following screen is displayed. This screen is
utilized to change the password used for
administrator authentication.
Show status
The following unit settings can be displayed.
Network
Verify the network settings
Softwave version
Verify the version numbers
of installed software
packages
Access control
Display dsnet access
control settings
Enter the desired password in the “Password” and
“Retype Password” fields. Click “Setting” to
complete the configuration.
Caution
• For security purposes, be sure to change the default
password.
• The password must be a combination of both letters and
numeric characters. Passwords consisting of all lowercase,
all uppercase or all numeric characters are not allowed.
• A password may be seven or eight characters long.
Passwords fewer than seven characters long are not allowed.
Also, if nine or more characters are entered, only the first
eight characters are set as the password.
• If an error is made in entering the password, or the values
entered into the “Password” and “Retype password” fields
do not match, an error message is displayed. If this occurs,
enter the password again.
Setting up
19
Setting up
User password
Date & time
Upon clicking “User password”, the following
screen is displayed. This screen is utilized to
change the user password used to log in to the
system.
Upon clicking “Date & time”, the following
screen is displayed. This screen is used to
configure the date, time and time zone.
Preparing to use the unit
Enter the desired password in the “Password” and
“Retype Password” fields. Click “Setting” to
complete the configuration.
Caution
• For security purposes, be sure to change the default
password.
• The password must be a combination of both letters and
numeric characters. Passwords consisting of all lowercase,
all uppercase or all numeric characters are not allowed.
• A password may be seven or eight characters long.
Passwords fewer than seven characters long are not allowed.
Also, if nine or more characters are entered, only the first
eight characters are set as the password.
• If an error is made in entering the password, or the values
entered into the “Password” and “Retype password” fields
do not match, an error message is displayed. If this occurs,
enter the password again.
Enter values for the year, month, day and time,
and select the time zone. Click “Setting” to
complete the configuration.
Network
Upon clicking “Network”, the following screen is
displayed. This screen is used to change the
method for obtaining an IP address and to change
the values required for network configuration.
If you want to change the network settings, enter
the new network settings in the appropriate fields
in this screen and then click “Setting
confirmation”. The following confirmation screen
is then displayed.
20
Setting up
Setting up
Update
Upon clicking “Update”, the following screen is
displayed. This screen is used to update the
software required by the unit.
Click “Setting” to begin processing the settings.
After the configuration is set, the following
screen is displayed.
Caution
Upon clicking “Setting confirmation” (see the step below),
the versions of files that are already installed and the versions
of the update files are checked to confirm whether the update
files are more recent and to confirm the dependency
relationships between files.
This check is not performed if “No version checking” is
selected. It is recommended that the default setting (“Check
versions”) be used.
Modify the network connection mode as needed,
and access the URL displayed on the screen.
Enter the path to the file to be
updated, and click “Setting
confirmation”.
The following screen is displayed, and the
contents of the update file are displayed.
Setting up
21
Preparing to use the unit
Place the files to be updated in the
appropriate directories on the
development PC, and click “Update”.
The following screen appears.
Setting up
Verify the contents of the files, and
click “Setting”.
The installation will begin.
If the contents are incorrect, click “Back” to
make corrections.
To save the unit’s settings on the
development PC:
Reset of setting
This procedure may vary depending on the web browser used.
For details, refer to the instructions for the web browser.
Upon clicking “Reset of setting”, the following
screen is displayed. This screen is used to restore
the factory default network settings and
administrator password.
To configure the unit using settings
saved on the development PC:
Right-click on “psptool.conf” and then select
“Save Target As” or “Save Link As”.
Caution
Preparing to use the unit
Select the setting(s) to be initialized and click
“Setting confirmation” to complete initialization.
Check that the IP address defined in
the development PC’s settings file is
the same as the IP address assigned
to the unit.
If the IP address defined in the settings file
and the unit’s IP address are different, use a
text editor to change the IP address in the
settings file of the development PC.
Click “Browse” and select a file to use
for configuring the unit.
Click “Setting”.
The settings will be saved on the unit, and
the information will be modified.
Save & load
Access control
Upon clicking “Save & load”, the following
screen is displayed. This screen is used to save
the settings and to synchronize the settings with
the unit.
Upon clicking “Access control”, the following
screen is displayed. This screen is used to
configure the PCs that will be allowed to access
dsnet.
“dsnet” is a program package for operating the
unit.
22
Setting up
Setting up
To deactivate access control:
Self-diagnostic program
Upon clicking “Self-diagnostic program”, the
following screen is displayed. This screen is used
to perform a variety of self-diagnostic tests.
Select “Disable”, and click “Setting”.
This allows access from a PC that has been
configured with any IP address.
To activate access control:
Select “Enable”, and click “Setting”.
This allows access only from a PC that has
been configured with one of the set IP
addresses.
Enter the IP address to be registered,
and then click “Add IP address”.
This registers the IP address to which access
is permitted.
Click on “Delete” next to an IP address that
has already been registered to delete that
address.
Caution
Enter an IP address using one of the following formats:
• xxx.xxx.xxx.xxx (xxx = 0-255)
• xxx.xxx.xxx.xxx/yy (xxx = 0-255, yy = 0-32)
Preparing to use the unit
Click on the process to be performed.
The test will begin.
Restart of dsnetm
“dsnetm” is a program used to communicate
between the TCP/IP sockets on the unit and a
host PC.
Upon clicking “Restart of dsnetm”, the following
screen is displayed.
Click “Restart” to restart dsnetm and display the
restart status. After completing the restart, the
following screen is displayed.
Setting up
23
Setting up
Showing status
Click on the items to the right of “Show status”
to verify the settings.
Network
Preparing to use the unit
Upon clicking “Network”, the following screen is
displayed. This screen allows the user to verify
the unit's network settings.
Shutdown
Upon clicking “Shutdown”, the following screen
is displayed. This screen is used to reboot or shut
down the unit.
Software version
Upon clicking “Software version”, the following
screen is displayed. This screen displays the
versions of the software packages installed on the
unit and allows the user to verify the unit's update
history.
To reboot:
Select “Reboot” and click “Setting”.
The reboot process will begin. It will take a
few minutes to complete.
To shutdown:
24
Select “Shutdown” and click
“Setting”.
This starts the termination process. The
power will be automatically turned off and
the unit will enter standby mode. The power
can also be turned off (thereby putting the
unit into standby mode) by pressing the
on/standby button on the front of the unit.
Setting up
Setting up
Access control
Upon clicking “Access control”, the following
screen is displayed. This screen lists the dsnet
access control status and the IP addresses that
have been granted access. This allows the user to
verify this information.
Preparing to use the unit
Usage notice
For this product, the debugger (dstdb) reset
command cannot be used when the power/hold
switch of the controller is in the hold position.
Make sure that the controller’s power/hold switch
is not in the hold position when operating the
debugger.
Setting up
25
Chapter
Appendices
Appendices
Troubleshooting
The power does not turn on.
Check that the AC adaptor and the AC power cord are securely connected.
The unit cannot be accessed over the network while in use.
Check that the power indicator lights up in green to verify that the unit is turned on.
Check that the network cable is securely connected.
Check that the unit's settings have not been changed by other PCs. Contact your network
administrator for assistance.
When network settings are modified, the unit can no longer be accessed.
The network setting may not be correct.
Check the settings displayed on the connected controller. If no settings are displayed on the
controller, disconnect and reconnect the power. The settings will then be displayed on the
controller.
About checking settings
Check that you can access the currently connected network using the values for IP address/subnet mask
that have been configured. For details, please consult your network administrator.
To check whether the development computer and the unit are correctly communicating, start the ping
command from the development computer. For details regarding the use of the ping command, see the
“About the ping command” section below, or refer to the instruction manual supplied with the
development computer.
Also, by pressing the network initialise button, you can return the IP address settings to their factory
default state.
About the ping command
If your development PC’s operating system supports the “ping” command, enter the ping
command as shown below.
# ping (the IP address of the unit)
26
Troubleshooting
Troubleshooting
When network communications are functioning, you will see information like the following at a
fixed interval:
PING 192.168.0.10 (192.168.0.10): 56(84) data bytes
64 bytes from 192.168.0.10: icmp_seq=0
ttl=64 time=0.1 ms
64 bytes from 192.168.0.10: icmp_seq=1
ttl=64 time=0.1 ms
64 bytes from 192.168.0.10: icmp_seq=2
ttl=64 time=0.1 ms
(continued below)
• When the indicator flashes orange:
The communications are functioning properly.
• When the indicator is not turned on:
The communications are not functioning properly. This may be due to disconnected
cables, damaged connections, or a unit malfunction.
The unit cannot be accessed, even though five minutes have elapsed since it was
turned on.
Check that the power indicator lights up in green.
If so,
there may be a problem with the network cable or the connected hub. Change the network cable
or hub, or contact your network administrator for assistance.
Wireless LAN communications are not working properly.
High-frequency noise from the controller may be affecting network communications. Try moving
the controller away from the unit’s aerial. Also try adjusting the position of the aerial or moving
the unit to a different location.
Troubleshooting
27
Appendices
When network communications are not functioning, the information will stop after the following:
PING 192.168.0.10 (192.168.0.10): 56 data bytes
If the display appears as shown above, check the following items:
• Is the network cable securely connected to the network connector on the unit?
• Is the network cable securely connected to the hub?
• Is the network cable securely connected to the development PC?
• Do the network settings of the development PC match those of the unit?
After checking the above items, start the ping command from the development PC. Then check
the indicator next to the network connector on the rear of the unit.
Specifications
Main unit (DTP-T1000 A)
Appendices
Compatible discs
CD-ROM / CD-R / DVD-ROM / DVD-R /
UMDTM
Power
Input voltage
DC IN 19.5V
Power consumption
5A
Operating environment
Operating temperature 10°C - 35°C
Operating humidity
30% - 70%
(not condensed)
Dimensions (excluding protrusions)
Development tool 100 x 280 x 298 mm
Controller
170 x 74 x 23 mm
(w/h/d)
Weight
Development tool
5.0 kg or less
Controller
Approx. 470 g
(including cables)
Processor
Dedicated processor (max 333 MHz)
Built-in memory
64 MB (fixed)
Built-in peripherals
Communication processor (300 MHz)
External interfaces
USB connector x 1
Memory Stick DuoTM slot x 1
Controller connector x 1
Foot switch connector x 1
Headset connector x 1
RF (extension) connector x 1
Aerial x 1
(For wireless LAN IEEE 802.11b)
Network connector x 1
(100 BASE-TX/10 BASE-T)
VGA connector x 1
(Analog RGB, D-SUB, 15-pin)
AUDIO OUT (audio output) connector x 1
(RCA pin)
Dedicated connector for servicing x 1
(For use by service personnel only.)
Extension connector x 1
(Devices other than those designated
cannot be used.)
Wireless LAN channels
USA and Canada
Europe
1-11 ch.
1-13 ch.
AC adaptor (DTP-H100)
Power
Input voltage AC
Output voltage DC
Rated frequency
Power consumption
100 - 240V (±10%)
19.5 V
50/60Hz (±2%)
1.6A (100V), 0.7A
(240V)
External dimensions
160 x 38 x 80 mm
(w/h/d)
Weight
Approx. 570 g
Supplied accessories
Instruction manual x 1
AC power cord for use in Oceania x 1
AC power cord for use in Europe x 1
AC power cord for use in Korea x 1
AC power cord for use in the UK x 1
AC power cord for use in the USA and
Canada x 1
AC adaptor x 1
Controller x 1
(With controller-interface cable [1.5 m])
Foot switch [1.9 m] x 1
RFI filter for use in Europe, Oceania and
Korea x 1
Fitting band for use in Europe, Oceania and
Korea x 1
Design and specifications are subject to
change without notice.
28
Specifications
R&TTE Directive "Informal DoC" statement
For customers in Europe
"Informal DoC"
Danish
Undertegnede Sony Computer Entertainment Inc. erklærer herved, at følgende
udstyr DTP-T1000 overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF. For yderligere information gå ind på følgende hjemmeside:
http://www.compliance.sony.de/
Dutch
Hierbij verklaart Sony Computer Entertainment Inc. dat het toestel DTP-T1000 in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG. Nadere informatie kunt u vinden op:
http://www.compliance.sony.de/
English
Hereby, Sony Computer Entertainment Inc. declares that this DTP-T1000 is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. For details, please access the following URL:
http://www.compliance.sony.de/
Finnish
Sony Computer Entertainment Inc. vakuuttaa täten että DTP-T1000 tyyppinen laite
on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen. Halutessasi lisätietoja, käy osoitteessa:
http://www.compliance.sony.de/
French
Par la présente Sony Computer Entertainment Inc. déclare que l’appareil
DTP-T1000 est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE. Pour toute information complémentaire,
veuillez consulter l’URL suivante: http://www.compliance.sony.de/
German
Hiermit erklärt Sony Computer Entertainment Inc. dass sich dieser/diese/dieses
DTP-T1000 in Übereinstimmung mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Weitere
Informationen erhältlich unter: http://www.compliance.sony.de/
Greek
Με την παρούσα η Sony Computer Entertainment Inc. δηλώνει τι DTP-T1000
συµµορφώνεται προς της ουσιώδεις απαιτήσεις και της λοιπές σχετικές
διατάξεις της οδηγίας 1999/5/EK. Για λεπτοµέρειες παρακαλούµε πως
ελένξετε την ακλουθη σελίδα του διαδικτύου:
http://www.compliance.sony.de/
Italian
Con la presente Sony Computer Entertainment Inc. dichiara che questo
(DTP-T1000) è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE. Per ulteriori dettagli, si prega di consultare il
seguente URL: http://www.compliance.sony.de/
Portuguese
Sony Computer Entertainment Inc. declara que este DTP-T1000 está conforme
com os requisitos essenciais e outras provisões da Directiva 1999/5/CE. Para mais
informacoes, por favor consulte a seguinte URL: http://www.compliance.sony.de/
Spanish
Por medio de la presente Sony Computer Entertainment Inc. declara que el
(DTP-T1000) cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Para mayor
información, por favor consulte el siguiente URL: http://www.compliance.sony.de/
Swedish
Härmed intygar Sony Computer Entertainment Inc. att denna DTP-T1000 står I
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG. För ytterligare information gå in
på följande hemsida: http://www.compliance.sony.de/
R&TTE Directive "Informal DoC" statement
29
Appendices
Language
Limitations of liability
This product is supplied pursuant to and subject to the terms of the tool loan agreement with Sony
Computer Entertainment Inc. or its affiliates. Other than as expressly set forth by SCEI and/or any of its
affiliates, except to the extent prohibited by applicable laws, SCEI and/or any of its affiliates shall not be
liable for any damages, including special, incidental or consequential damages, or fees arising out of the
use or inability to use this product.
Appendices
30
Limitations of liability
Appendices
31
This product may fall within the scope of national export control legislation.
You must comply fully with the requirements of such legislation and of all other applicable laws of any
jurisdiction in relation to this product.
Contact information:
Japan
3rd Party Relations Division
Sony Computer Entertainment Inc.
7-1-1 Akasaka, Minato-ku,
Tokyo 107-0052 Japan
TEL: +81-3-6438-8635 (direct)
Korea
Technology Group
Sony Computer Entertainment Korea Inc.
14Fl. Koosan Tower, 3250, Bangbae2-Dong
Seocho-Gu, Seoul, #137-853 Korea
E-mail: psp_support@scek.co.kr
TEL: +82-2-6230-3596 (direct)
United Kingdom (Europe)
Technology Group
Sony Computer Entertainment Europe
25 Golden Square
London W1F 9LD UK
TEL: +44-207859-5777 (direct)
http://www.scee.sony.co.uk/
USA
Developer Support
Sony Computer Entertainment America
919 East Hillsdale Boulevard, 2nd Floor
Foster City, CA 94404-2175 USA
TEL: +1-650-655-5566 (direct)
FAX: +1-650-655-5511 (direct)
Without obtaining the consent of the owner, no part of the content of this document may be copied, pursuant
to the provisions of the Copyright Act.
“
” is a registered trademark and “
Entertainment Inc.
” and “UMD” are trademarks of Sony Computer
“SONY” and “ ” are registered trademarks and “Memory Stick Duo”, “Memory Stick PRO Duo” and “
are trademarks of Sony Corporation.
© 2005 Sony Computer Entertainment Inc. All rights reserved.
”
Printed in Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Page Count                      : 32
Page Mode                       : UseOutlines
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:02390ccd-08ab-4d10-9d4f-5826a5a262bf
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Create Date                     : 2005:02:10 05:16:39Z
Modify Date                     : 2005:02:10 17:40:50+09:00
Metadata Date                   : 2005:02:10 17:40:50+09:00
Document ID                     : uuid:1970f54c-2084-4fe5-83ec-eef1299a801d
Format                          : application/pdf
Title                           : DTP-T1000 A
Creator                         : Sony Computer Entertainment Inc.
Author                          : Sony Computer Entertainment Inc.

EXIF Metadata provided by EXIF.tools