Sony S480C Sony Remote Card System Reader/Writer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	86124
Application ID	MjndAB93EkJLSqw7iRlBIg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	29.41kB (367617 bits)
Date Submitted	2000-02-11 00:00:00
Date Available	2000-03-17 00:00:00
Creation Date	2001-04-13 17:11:18
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-04-13 17:11:19
Document Title	User Manual

Sony Confidential
Reader/Writer RC-S480C Users Manual
(Version 1.50)
 Sony Corporation
30 November 1999
Contents
1 Definition
General
2.1
Basic Specification
2.1.1
Dimensions
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
2.1.2
2.1.3
Communication Protocol
Re-sending Protocol
ACK/NACK Packet
Mutual Authentication
Encryption and Decryption
Communication Commands
4.1
General
4.2
Reader/Writer Internal Operation Commands
4.2.1
Attention Command
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
4.2.9
4.2.10
4.2.11
4.3
4.4
Authentication 1 Command
Authentication 2 Command
Disconnect Command
Change Reader/Writer Access Key Command
Self-Diagnosis Command
Check Firmware Version Command
Change Communication Mode Command
Kill Module Command
Reader/Writer Reset Command
Firmware Maintenance Command
Card Operation Command
4.3.1
Polling Command
4.3.2
4.3.3
Request Service Command
Request Response Command
4.3.4
Mutual Authentication Command
4.3.5
4.3.6
4.3.7
4.3.8
4.3.9
Read Block Command
Write Block Command
Release Command
Read Without Encryption Command
Write Without Encryption Command
Card Management Command
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
Specification Table
Encryption Technique
Reader/Writer Operation
3.1
Connection with Controller
3.2
Transaction Overview
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
Sony Confidential ii
Register Issue ID Command
Register Area Command
Register Service Command
Register Manufacture ID Command
Card Self-Diagnosis Common Security Key Command
Fundamental Specifications
5.1
Operating Temperature
5.2
Storage Temperature
5.3
Humidity
5.4
Cold and Heat Shock
5.5
Shock
5.6
Vibration
5.7
Spurious Emissions
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
5.8
5.9
5.10
5.11
Sony Confidential iii
Bump
Electrostatic Discharge
Multiple cards
Anti-Collision
Reader/Write Specification Table
6.1
B-antenna Reader/Writer
6.1.1
6.1.2
6.2
B-antenna Reader/Writer Specification Table
B-antenna Reader/Writer Schematic Drawing
C-antenna Reader/Writer
6.2.1
6.2.2
C-antenna Reader/Writer Specification Table
C-antenna Reader/Writer Schematic Drawing
13
15
15
17
List of Table
Table 1
Table 2
Table 3
Table 4
Reader/Writer Internal Operation Command
Card Operation Command
Card Management Command
Pin Assignment of Interface Connector CN2
11
List of Figures
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Fig.7
Fig.8
Communication Protocol and Packet Structure
Printed Model No. (B-antenna)
RF/Control Board Attached to External Board
Pin Assignment of Connectors CN1-2
RF/Control Board
Antenna Board (B-antenna)
Printed Model No. (C-antenna)
Antenna Board (C-antenna)
10
11
13
14
15
17
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
Definition
In this document, following words are used in the following sense.
Controller - An external computer, a gate controller or equivalent equipment directly
connected to Reader/Writer through specified wired interface.
Reader/Writer - The equipment, specified in this document, for Sony Remote Card System:
FeliCa
Card - A Contactless Smart Card for Sony Remote Card System: FeliCa
General
2.1
Basic Specification
Reader/Writer consists of 3 parts – an antenna board, an RF/control board and the cable
that connects the antenna board and the RF/control board.
2.1.1
Dimensions
The dimension of each type is described in Chapter 6.
The tolerance is ±0.5mm.
2.1.2
Specification Table
Communication with Card
data transfer rate
: 250kbps or 211.875kbps
carrier frequency
: 13.56MHz (±50ppm)
modulation
: Receive - ASK, Manchester Coding
: Transmit - ASK(12±2%), Manchester Coding
modulation bandwidth
: ±300kHz (-30dB relative to carrier level)
radiation level
: less than 2000µV/m at 10m distance (C-antenna)
: less than 300µV/m at 10m distance (B-antenna)
Communication method
: half-duplex, CRC16
Power Supply (see Chapter 6)
Digital Processing Unit (DPU)
IC CXD8680R (designed by Sony)
CXD8680R has 32 bit CPU core, 8 kbyte ROM, 3 kbyte SRAM, 2 kbyte
Block Erasable Flash Memory and 4x32 kbyte Flash Memory inside.
Controller Interface (serial interface)
number of ports
: 1 (one)
signal level
: CMOS logic level
baud rate for operation
: 7.2kbps ~ 1.2288Mbps
(7.2, 8.192, 9.6, 14.4, 16.384, 19.2, 28.8, 32.768, 38.4, 57.6, 65.536, 76.8, 115.2,
131.072, 153.6, 230.4, 262.144, 460.8, 524.288, 921.6, 1048.576, 1228.8 kbps)
communication method : half-duplex, check sum
2.1.3
Encryption Technique
All communications to and from the Card, with the exception of Polling Command,
are encrypted.
All the communications to and from the Controller, with the exception of the Attention
Command, are encrypted.
3 kinds of Encryption algorithm, Single-DES 56bit, Triple-DES 56bit and SEAC (Sony
Encryption Algorithm for Card) 64bit, can be applied.
Reader/Writer Operation
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
3.1
3.2
Sony Confidential
Connection with Controller
The pin assignment is described in Chapter 6.
Transaction Overview
3.2.1
Communication Protocol
There are two communication protocols, namely, data link level and application level
protocol.
Either ACK or NACK packet is returned in every packet transfer. ACK indicates a
successful transfer, NACK means unsuccessful.
Controller
Reader/Writer
Command Packet
ACK
Max. 2ms
Start of Packet Code
Response Packet
Max. 2ms
00
00
FF
Packet Length Checksum
Packet Data Checksum
Command or Response Code
LEN LCS PD0
PD1
…
PDn DCS
00
ACK
Preamble
Packet Length
Packet Data
Postamble
Fig. 1 : Communication Protocol and Packet Structure
3.2.2
Re-sending Protocol
Reader/Writer supports the re-sending procedure in Controller interface. Re-sending
handling is triggered or required in the two cases below :
1. NACK packet is returned.
2. Neither ACK nor NACK response comes. (time out)
Controller should re-send the same packet within 5ms after receiving NACK or
detecting time out.
3.2.3
ACK / NACK Packet
ACK / NACK packet format is as follows :
ACK : LEN = 00h & LCS = ffh without Packet Data part and DCS
NACK : LEN = ffh & LCS = 00h without Packet Data part and DCS
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
3.2.4
Mutual Authentication
Mutual Authentication is a process that is performed between Controller and
Reader/Writer to authenticate each other mutually in order to avoid the fraud usage.
This authentication is based on the following elements :
1. two 8byte (64bit) keys
2. three pass authentication model (ISO 9758)
3. cryptography algorithm mentioned in section 3.2.5.
3.2.5
Encryption and Decryption
The cryptography algorithm is used for the following three stages :
1. mutual authentication between Controller and Reader/Writer
2. mutual authentication between Reader/Writer and Card
3. commands and data encryption through Reader/Writer
Communication Commands
4.1
General
In this section, the communication commands between Controller and Reader /Writer are
described.
Table 1-3 shows all commands between Controller and general Reader/Writer. All
commands are categorized into 3 groups as follows :
1. Reader/Writer internal operation command
2. Card operation command
3. Card management command
Card management command group is for issue Reader/Writer and not for general
Reader/Writer .
4.2
Reader/Writer Internal Operation Command
4.2.1
Attention Command
Attention Command enables Reader/Writer and Controller to recognize each other and
is the only command available before the authentication completes. The main purpose of
this Attention Command is to recognize its partner before authentication and to force
Reader/Writer to be in the idle state.
4.2.2
Authentication 1 Command
Authentication 1 Command enables Controller to authenticate Reader/Writer.
4.2.3
Authentication 2 Command
Authentication 2 Command enables Reader/Writer to authenticate Controller.
4.2.4
Disconnect Command
Disconnect Command is for Controller to terminate the communication with
Reader/Writer.
Command
Command Code
Response Code
Attention
00h
01h
Authentication 1
02h
03h
Authentication 2
04h
05h
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
Disconnect
06h
07h
Change Reader/Writer Access Key
20h
21h
Self-Diagnosis
40h
41h
Check Firmware Version
44h
45h
Change Communication Mode
46h
47h
Kill Module
4ah
4bh
Reader/Writer Reset
4ch
4dh
Firmware Maintenance
52h
53h
Table 1 : Reader/Writer Internal Operation Command
Command
Command Code
Response Code
Polling
80h
81h
Request Service
82h
83h
Request Response
84h
85h
Mutual Authentication
86h
87h
Read Block
88h
89h
Write Block
8ah
8bh
Release
8eh
8fh
Read Without Encryption
98h
99h
Write Without Encryption
9ah
9bh
Table 2 : Card Operation Command
Command
Command Code
Response Code
Register Issue ID
c0h
c1h
Register Area
c2h
c3h
Register Service
c4h
c5h
Register Manufacture ID
e0h
e1h
Card Self-Diagnosis
f0h
f1h
Table 3 : Card Management Command
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
4.2.5
Change Reader/Writer Access Key Command
Change Reader/Writer Access Key Command performs alteration of the access
keys, which are stored in Reader/Writer for the mutual authentication between Controller
and Reader/Writer.
4.2.6
Self-Diagnosis Command
Self-Diagnosis Command activates self-diagnosis test of Reader/Writer. After the
Diagnosis completion, Reader/Writer sends back the test result.
4.2.7
Check Firmware Version Command
Check Firmware Version Command is used for checking the version of
Reader/Writer firmware.
4.2.8
Change Communication Mode Command
Change Communication Mode Command performs the following changes : baud
rate, logic level interface(non-inverted or inverted), encryption on/off, time-out.
4.2.9
Kill Module Command
Kill Module Command is used for killing the specified module within Reader/Writer.
4.2.10
Reader/Writer Reset Command
Reader/Writer Reset Command executes the initialization routine.
4.2.11
Firmware Maintenance Command
Firmware Maintenance Command is used for updating the firmware within
Reader/Writer.
4.3
Card Operation Command
4.3.1
Polling Command
Polling Command enables Reader/Writer to give a call to Card and to detect existence
of Card by the response from Card.
4.3.2
Request Service Command
Request Service Command enables Reader/Writer to check whether the specified
service code is registered to Card or not. In case that the specified service is registered to
Card, key version of the service is available by the response from Card.
4.3.3
Request Response Command
Request Response Command enables Reader/Writer to check which mode Card is
in. There are 4 modes, ‘before Authentication’, ‘after Authentication 1’, ‘after
Authentication 2’ and ‘after Register xxx Command (see 4.4 Card Management
Command)’.
4.3.4
Mutual Authentication Command
Mutual Authentication Command activates the mutual authentication procedure
between Reader/Writer and Card.
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
4.3.5
Read Block Command
Read Block Command activates Reader/Writer to read the specified block data from
Card after the mutual authentication between the Reader/Writer and Card has been
established successfully.
Read Block Command enables a Service Provider with successful mutual authentication
to read blocks that this Service Provider has the right to access.
With one Read Block Command, up to 8 block can be read simultaneously. If more
than 8 blocks should be read, more than one Read Block Command shall be called
separately.
The response of Read Block Command is a 1byte Read result and Block Data that has
been read. In the Read result, a 1byte consequence of one block Read is given in 1bit. As
there are up to 8 blocks, 1byte is enough to record all the Read consequence.
4.3.6
Write Block Command
Write Block Command activates Reader/Writer to write the specified block data to
Card as new data after the mutual authentication between Reader/writer and Card has
been established successfully.
With one Write Block Command, up to 8 block can be written simultaneously. If more
than 8 blocks should be written, more than one Write Block Command shall be called
separately.
The response of Write Block Command is a 1byte Write result. In the Write result, a
1byte consequence of one block Write is given in 1bit. As there are up to 8 blocks, 1byte
is enough to record all the Write consequence.
The purse operation can be performed with Write Block Command.
4.3.7
Release Command
Release Command enables Card to be released from established communication
sequence with Reader/Writer.
4.3.8
Read Without Encryption Command
Read Without Encryption Command activates Reader/Writer to read the specified
block data from Card without the mutual authentication between the Reader/Writer and
Card. Read Without Encryption Command can be applied only to blocks which
service code is registered security-free.
The number of blocks that can be read simultaneously and the response of Read
Without Encryption Command are the same as those for Read Block Command (see
4.3.5).
4.3.9
Write Without Encryption Command
Write Without Encryption Command activates Reader/Writer to write the specified
block data to Card without the mutual authentication between the Reader/Writer and
Card, however can be applied only to blocks which service code is registered securityfree.
The number of blocks that can be write simultaneously and the response of Write
Without Encryption Command are the same as those for Write Block Command (see
4.3.6).
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
4.4
Card Management Command
The commands described in this section are for issue Reader/Writer and not for general
Reader/Writer .
4.4.1
Register Issue ID Command
Register Issue ID Command makes it possible to register Issue ID(IDi) , Issue
Parameter(PMi), System Code and Area 0000 Key to Card, and also makes it to erase
other services and to initialize Memory Allocation Information in Card.
4.4.2
Register Area Command
Register Area Command makes it possible to register new Area and the parameters of
new Area to Card, which are Service Code Range, Available Block Number and Area
Key.
4.4.3
Register Service Command
Register Service Command makes it possible to register new Service and the
parameters of new Service to Card, which are Service Code, Block Number and Service
Key.
4.4.4
Register Manufacture ID Command
Register Manufacture ID Command makes it possible to register Manufacture
ID(IDm) , Manufacture Parameter(PMm), System Code, System Key and Area 0000 Key
to Card, and also makes it to clear Issue ID of Card.
In order to execute Register Manufacture ID Command, Manufacture ID must be all
00h. This means that Register Manufacture ID Command is effective to Card once for
all.
4.4.5
Card Self-Diagnosis Command
Card Self-Diagnosis Command activates self-diagnosis test of Card. After the
Diagnosis completion, Card sends back the test result.
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
Fundamental Specifications
5.1
Operating Temperature
-20 to 70°C
Compliant to IEC 68-2-2 Part 2 Test Bd and IEC 68-2-1 Part 2 Test Ad, with duration 16
hours.
5.2
Storage Temperature
-40 to 80°C
Compliant to IEC 68-2-2 Part 2 Test Bb and IEC 68-2-1 Part 2 Test Ab, with duration 72
hours.
5.3
Humidity
Compliant to IEC 68-2-3 Part 2 Test Ca, with duration 4 days.
5.4
Cold and Heat Shock
Compliant to IEC 68-2-1 Part 2 Test Aa, with temperature -20°C and duration 2 hours, and
IEC 68-2-2 Part 2 Test Ba, with temperature 70°C and duration 2 hours.
5.5
Shock
Compliant to IEC 68-2-27 Part 2 Test Ea, severity 60g, duration 11ms.
5.6
Vibration
Compliant to IEC 68-2-6 with respect to the following parameters :
• Frequency Range : 10Hz to 500Hz
• Vibration Severity : 3gn
• Sweep rate : 1 octave per minute
• Endurance by sweeping : 20 sweep cycles for each X,Y and Z axis.
5.7
Spurious Emissions
Compliant to MPT 1339 clause 4.1.3 ; FCC Regulation Part 15.225 and Part 15.209 ; and
EC(EU) I-ETS 300 330 clause 7.2.1.3.
5.8
Bump
Compliant to IEC 68-2-29 Part 2 Test Eb, severity 40gn, duration 6ms and 4000 bumps.
5.9
Electrostatic Discharge
Compliant to IEC 801-2, with severity level 3 (Test Voltage Air discharge : 8kV ).
5.10 Multiple Card
The Reader/Writer allows addressing and authentication of up to four Cards in the
communication area. Each Card will only respond to commands intended for it and only
one Card can be addressed in a single command.
5.11 Anti-Collision
Reader/Writer supports anti-collision of multiple cards.
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
Reader/Writer Specification Table
6.1
B-antenna Reader/Writer
6.1.1
B-antenna Reader/Writer Specification Table
•
Model No. : RC-S480B
General model No. “RC-S480” is printed on the RF/Control board (see Fig.2). “Bantenna” means antenna type shown in Fig.6 and it is marked on “B” as in Fig.2. A
mark on numerals 1-5 (it is 1 in Fig.2) indicates the installed software version.
RC-S480
A B C D E F
1 2 3 4 5 6
Fig. 2 : Printed Model No. (B-antenna)
•
•
Operating Distance : 30mm
The Reader/Writer is adjusted by the combination of the RF/Control board and
the antenna board, both of which shall have the same serial number labels to
maximize the operating distance, and therefore, the operating distance cannot be
assured by the different combination of the boards.
The antenna board and the RF/Control board shall be placed more than 15mm
apart.
In the effective operating scope of the antenna, there shall be nothing that
generates electric or magnetic noise. Neither shall there be an electric or magnetic
shield or reflection.
Emission from another Reader/Writer affects the operating distance. In operating
plural Reader/Writers simultaneously, it is desirable for antenna boards to be
separated more than 30cm each other in order to keep the 30mm operating
distance. However, Reader/Writers can be operated under less than 30cm
separation each other with no problem except for decrease of the operating
distance.
Dimensions (see Fig.5 and 6)
antenna : 50mm x 25mm x 6mm (PCB thickness 1mm, connector height 5mm)
RF/Control board : 50mm x 60mm x 15mm (PCB thickness 1mm)
cable : length 120mm
The RF/Control board can be attached to external board by the interface connector
CN2 as is shown in Fig.3.
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Variable Capacitor
to Antenna Board
External Board
CN1 (4pin)
Sony Confidential
10
RF/ Control Board
CN2 (40pin)
Fig.3 : RF/Control Board Attached to External Board
•
Mounting Holes (see Fig.5,6)
antenna : (no mounting hole)
RF/Control board : M3 x 2, clearance 8mm
•
Interface Connector : HKP-40M1 (Honda Tsushin Kogyo Co., Ltd.)
The interface connector is a 40-pin double row C-antennaonnector located at the
lower edge of the RF/Control board which is shown in the schematic drawing of
Fig.5. The pitch of connector pins is 2.54mm.Connector pins are gilded.
The left end of the bottom row of connector pins is No. 1. Pin assignment of the
connector (CN2) is shown in Fig. 4 and Table 4.
12V
:DC input port (for RF power amplifier)
5V
:DC input port
GND
:Ground port
SI, SO
:Serial Data I/O (CMOS 5V)
DA0-7
:Parallel Data I/O (CMOS 5V)
DA0-7 are connected to PG0-7 of DPU IC CXD8680R. In order to
control DA0-7, it is necessary to load other program code to
RF/Control board. (see “Reader/Writer Programmer’s Reference
Manual“)
DB0-7
:Parallel Data I/O (CMOS 5V)
DB0-7 are connected to PH0-7 of DPU IC CXD8680R. In order to
control DB0-7, it is necessary to load other program code to
RF/Control board. (see “Reader/Writer Programmer’s Reference
Manual“)
HS0-3
:Parallel Data I/O (CMOS 5V)
HS0-2 are connected to PF4-6 of DPU IC CXD8680R, and HS3 is
connected to both PF7 and PF2. In order to control HS0-3, it is
necessary to load other program code to RF/Control board. (see
“Reader/Writer Programmer’s Reference Manual“)
Mode
:No connection in usual operation.
Only in loading program, high level voltage (5V) shall be applied to
the pin before RF/Control board is powered on
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Modu., Demodu. & Power Amp.
Sony Confidential
Controller
*WD
*WD
SO
RD
RD
SI
CN1
CARRIER
5V
*CARRIER
EN/*INH
*R/W
DA[0-7]
DA[0-7]
CARRIER
DB[0-7]
DB[0-7]
*CARRIER
HS[0-3]
EN/*INH
5V
*R/W
GND
RFIN+
RFINRFOUT+
RFOUT-
GND
12V
to Antenna
HS[0-3]
MODE
Fig.4 : Pin Assignment of Connectors CN1-2
Pin No.
Pin Assignment
Pin Assignment
Pin No.
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
12V
12V
No Connection
No Connection
DA0
DA1
DA2
DA3
DA4
DA5
DA6
DA7
HS0
HS1
HS2
HS3
No Connection
No Connection
GND
GND
No Connection
No Connection
GND
GND
SI
SO
No Connection
MODE
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
5V
5V
No Connection
No Connection
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Table 4 : Pin Assignment of Interface Connector CN2
11
CN2
12V 1
12V 3
DA0 7
10
DA1 9
11
12
DA2 13
14
DA3 15
16
DA4 17
18
DA5 19
20
DA6 21
22
DA7 23
24
HS0 25
26
HS1 27
28
HS2 29
30
HS3 31
32
33
34
35
36
GND 37
38
GND 39
40
CON40A
GND
GND
SI
SO
MODE
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
5V
5V
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
•
Sony Confidential
12
Power
voltage
:DC12V (CN2 pin1 and 3)
:DC5V (CN2 pin34 and 36)
voltage allowance
:DC12V +4V, -0.5V
:DC5V ±0.5V
current
:DC12V
≈ 90mA
:DC5V
≈150mA
voltage ripple allowance
:100mV (peak-to-peak)
The Reader/Writer can be operated in the voltage range of 5 - 11.5V and the
voltage ripple > 100mV for DC12V, however operating distance cannot be assured in
such condition.
•
External Interface
serial 1 port : CMOS logic level (5V)
software selectable, non-inverted or inverted, and baud rate
(default setting : non-inverted, 115.2kbps)
parallel 20bit I/O port : CMOS logic level (5V)
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
6.1.2
Sony Confidential
B-antenna Reader/Writer Schematic Drawing
Fig.5 : RF/Control Board (B-antenna & C)
13
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
Sony Confidential
Fig.6 : Antenna Board (B-antenna)
14
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
6.2
Sony Confidential
15
C-antenna Reader/Writer
6.2.1
C-antenna Reader/Writer Specification Table
•
Model No. : RC-S480C
General model No. “RC-S480” is printed on the RF/Control board (see Fig.7). “Cantenna” means antenna type shown in Fig.8 and it is marked on “C” as in Fig.7. A
mark on numerals 1-5 indicates (it is 1 in Fig.7) the installed software version.
RC-S480
A B C D E F
1 2 3 4 5 6
Fig. 7 : Printed Model No. (C-antenna)
•
Operating Distance : 100mm
The Reader/Writer is adjusted by the combination of the RF/Control board and
the antenna board, both of which shall have the same serial number labels to
maximize the operating distance, and therefore, the operating distance cannot be
assured by the different combination of the boards.
The antenna board and the RF/Control board shall be placed more than 15mm
apart.
In the effective operating scope of the antenna, there shall be nothing that
generates electric or magnetic noise. Neither shall there be an electric or magnetic
shield or reflection.
Emission from another Reader/Writer affects the operating distance. In operating
plural Reader/Writers simultaneously, it is desirable for antenna boards to be
separated more than 70cm each other in order to keep the 20mm operating
distance. However, Reader/Writers can be operated under less than 70cm
separation each other with no problem except for decrease of the operating
distance.
•
Dimensions (see Fig.5 and 8)
antenna :104mm x 67mm x 6mm (PCB thickness 1mm, connector height 5mm)
RF/Control board : 50mm x 60mm x 15mm (PCB thickness 1mm)
cable : length 120mm
The RF/Control board can be attached to external board by the interface connector
CN2 as is shown in Fig.3.
•
Mounting Holes (see Fig.5 and 8)
antenna
: M3 x 4, clearance 8mm
RF/Control board
: M3 x 2, clearance 8mm
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
•
•
•
Sony Confidential
16
Interface Connector : HKP-40M1 (Honda Tsushin Kogyo Co., Ltd.)
The interface connector is a 40-pin double row C-antennaonnector located at the
lower edge of the RF/Control board which is shown in the schematic drawing of
Fig.5. Connector pins are gilded. The left end of the bottom row of connector pins is
No. 1. Pin assignment of the connector (CN2) is shown in Fig. 4 and Table 4.
12V
:DC input port (for RF power amplifier)
5V
:DC input port
GND
:Ground port
SI, SO
:Serial Data I/O (CMOS 5V)
DA0-7
:Parallel Data I/O (CMOS 5V)
DA0-7 are connected to PG0-7 of DPU IC CXD8680R. In order to
control DA0-7, it is necessary to load other program code to
RF/Control board. (see “Reader/Writer Programmer’s Reference
Manual“)
DB0-7
:Parallel Data I/O (CMOS 5V)
DB0-7 are connected to PH0-7 of DPU IC CXD8680R. In order to
control DB0-7, it is necessary to load other program code to
RF/Control board. (see “Reader/Writer Programmer’s Reference
Manual“)
HS0-3
:Parallel Data I/O (CMOS 5V)
HS0-2 are connected to PF4-6 of DPU IC CXD8680R, and HS3 is
connected to both PF7 and PF2. In order to control HS0-3, it is
necessary to load other program code to RF/Control board. (see
“Reader/Writer Programmer’s Reference Manual“)
Mode
:No connection in usual operation.
Only in loading program, high level voltage (5V) shall be applied to
the pin.
Power
voltage
:DC12V (CN2 pin1 and 3)
:DC5V (CN2 pin34 and 36)
voltage allowance : DC12V +4V, -0.5V
:DC5V ±0.5V
current
:DC12V
≈ 150mA
:DC5V
≈ 150mA
voltage ripple allowance
:100mV (peak-to-peak)
The Reader/Writer can be operated in the voltage range of 5 - 11.5V and the
voltage ripple > 100mV for DC12V, however operating distance cannot be assured in
such condition.
External Interface
serial 1 port : CMOS logic level(5V)
software selectable, non-inverted or inverted, and baud rate
(default setting : non-inverted, 115.2kbps)
parallel 20bit I/O port : CMOS logic level (5V)
FeliCa : Reader/Writer RC-S480 Users Manual
Version 1.50
6.2.2
Sony Confidential
C-antenna Reader/Writer Schematic Drawing
Fig.8 : Antenna Board (C-antenna)
17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:04:13 17:11:18
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:04:13 17:11:19-04:00
Page Count                      : 20

EXIF Metadata provided by EXIF.tools