Sony Icd P320 Users Manual
ICD-P320 Operating Instruction ICDP320
ICD-P320 to the manual 07cf57df-850f-f354-7d97-61ea2843ad2d
2015-01-23
: Sony Sony-Icd-P320-Users-Manual-295015 sony-icd-p320-users-manual-295015 sony pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
BGetting started BBasic Operations Step 1: Installing the Batteries IC Recorder 1 Operating Instructions Replacing the batteries The battery indicator in the display window shows the battery condition. When flashes, replace the batteries with new ones. When flashes, the batteries are exhausted and the unit will stop operation. Slide and lift the battery compartment lid. Owner’s Record The model number is located at the rear and the serial number is located inside the battery compartment. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. ICD-P320 2 2005 Sony Corporation Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink. Insert two LR03 (size AAA) alkaline batteries with correct polarity, and close the lid. Printed in China Make sure to insert both of the batteries from their – ends. Information IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT. For the customers in the U.S.A. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-7669 or http://www.sony.com/ Declaration of Conformity Trade Name: Model: Responsible Party: Address: SONY ICD-P320 Sony Electronics Inc. 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Troubleshooting Before taking the unit for repair, check the following sections. Should any problem persist after you have made these checks, consult your nearest Sony dealer. The unit does not operate. • The batteries have been inserted with incorrect polarity. • The batteries are weak. • The buttons are locked with the HOLD switch. (If you press any button, “HOLD” will flash three times.) No sound comes from the speaker. If the battery compartment lid is accidentally detached, attach it as illustrated. Clock setting display appears when you insert batteries for the first time, or or when you replace the batteries with new ones. Please refer to Steps 2 to 3 in “Step 2: Setting the Clock” to set the date and time. • The ear receiver or headphones are plugged in. • The volume is turned down completely. “FULL” is displayed and you cannot start recording. • The memory is full. Erase some of the messages. • 99 messages have been recorded in the selected folder. Select another folder or erase some of the messages. Noise is heard. • An object, such as your finger, etc., accidentally rubbed or scratched the unit during recording so that noise was recorded. • The unit was placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback. • Plug of the connected microphone was dirty when recording. Clean the plug. • Ear receiver/headphones plug is dirty. Clean the plug. Recording Messages You can record up to 99 messages in each of the four folders (A, B, C, and D). Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording. e.g. Message 1 Message 2 Newly recorded message Note Before making a long recording, be sure to insert new batteries and check the battery indicator. With continuous use, approx. 11 hours recording/7.5 hours playback in the HQ mode, and approx. 22 hours recording/11 hours playback in the SP and LP modes is possible. * Using Sony alkaline batteries LR03 (size AAA) * When playing back through the internal speaker with the medium volume level The battery life may shorten depending on the operation of the unit. Notes • Do not use manganese batteries for this unit. • When you replace the batteries with new ones, the clock setting display appears. In this case, set the date and time again. The recorded messages and alarm setting, however, will remain. • When replacing the batteries, be sure to replace both batteries with new ones. • Do not charge dry batteries. • When you are not going to use the unit for a long time, remove the batteries to prevent damage from battery leakage and corrosion. • The unit is accessing data while “ACCESS“ appears in the display window or the OPR indicator flashes in orange. While accessing, do not remove the batteries. Doing so may damage the data. 1 2 3 7 h. 20 min. See “Changing the Recording Mode” on the reverse side. LP*** 32 h. 10 min. Select the folder. (h.: hours/min.: minutes) * HQ: High quality recording mode (monaural sound) ** SP: Standard play recording mode (monaural sound) ***LP: Long play recording mode (monaural sound) Start recording. Recording mode Current message number Counter display* 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. The unit enters the menu mode. 2 Press – . or >+ to display “SET DATE”. 3 Press NxPLAY/STOP. The year digits will flash. Recording is interrupted. Stop recording. • You have not set the clock. 2 Set the date. 1 Press – . or >+ to select the digits of the year. “--Y--M--D” or “--:--” is displayed on the REC DATE display. 2 Press NxPLAY/STOP. The month digits will flash. 3 Set the month and day in sequence, then press NxPLAY/ STOP. The hour digits will flash. • The date and time of recording will not be displayed if you recorded the message when the clock was not set. You cannot divide a message. • You cannot divide a message in a folder which has 99 messages. • If you divide messages frequently, the unit may become unable to divide a message. • You cannot divide a message in the first or the last 1 second of a message. You cannot record messages up to the maximum recording time. • If you record messages in a mixture of HQ, SP and LP modes, the recordable time varies from the maximum HQ mode recording time to the maximum LP mode recording time. • No more recording can be made when 99 messages each have been recorded in a folder. • Due to the limitation of the IC recording system, this unit records in the minimum recording unit. If the length of each message cannot be divided by the minimum recording unit, the remaining recording time may decrease by more than the total length of the messages. The unit does not operate correctly. • Take out the batteries and insert them again. Please note that recorded messages may be erased during service or repair work. Press xSTOP. The unit stops at the beginning of the current recording. If you do not change the folder after you stop recording, the next time you record you will record in the same folder. To Do this pause recording* Press zXREC/PAUSE. During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window. release pause and resume recording Press zXREC/PAUSE. Recording resumes from that point. (To stop recording after pausing recording, press xSTOP.) listen to the current recording Press xSTOP to stop recording, then press NxPLAY/STOP. review the current recording instantly Press NxPLAY/STOP during recording. search backward during recording (Review) Hold down – . during recording or recording pause. Recording mode will be released, and reviewing of the current recording starts. If you release the button, playback starts from that point. select the microphone sensitivity You can select the microphone sensitivity using the menu. See “Selecting the Microphone Sensitivity”. H (high): To record at meeting or in a quiet and/or spacious place. L (low): To record for dictation or in a noisy place. * About one hour after you pause recording, recording pause is automatically released and the unit goes into the stop mode. 1 Tip To set the date to Year 2006, display “06Y”. Selecting the Folder 3 1 Set the time. 1 Press – . or >+ to select the digits of the hour. 2 Press NxPLAY/STOP. The minute digits will flash. The remaining time displayed in the display window is shorter than that displayed in the supplied “Digital Voice Editor“ software. • The unit requires a certain amount of memory for system operation. That amount is subtracted from the remaining time, which is the reason for the difference. NxPLAY/STOP – .(Review) • The advanced VOR function is activated. Set VOR to “OFF”. “--Y--M--D” or “--:--” is displayed. OPR indicator (lights in red during recording.) You do not need to keep pressing zXREC/PAUSE while recording. Clock setting display appears when you insert batteries for the first time, or when you replace the batteries with new ones. In this case, proceed from step 2. • Set the microphone sensitivity to “H (high)” using the menu. • This unit is designed to automatically adjust the recording level when recording meetings, etc., and is not suitable for music recording. 2 Speak to the built-in microphone. * The display selected with the DISPLAY/ MENU button appears. Remaining memory indicator Display the clock setting display. 3 Set the minute. 2 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. Press – . or >+ to select “FOLDER” and press NxPLAY/STOP. 4 Press NxPLAY/STOP at the time signal. The display will return to “SET DATE”. 3 Press – . or >+ to select the folder you want and press NxPLAY/STOP. 5 Press xSTOP to exit from the menu mode. If the unit is left unused for more than 3 seconds in the stop mode, the display will show the current time. 4 Press xSTOP to exit the menu mode. Current folder 1 Tip This unit does not have a power on/off switch. The display is shown at all times. 2 Press – . or >+ to select “SENS” and press NxPLAY/STOP. 3 Press – . or >+ to select “H (high sensitivity)” or “L (low sensitivity)” and press NxPLAY/STOP. 4 Press xSTOP to exit the menu mode. Notes Step 2: Setting the Clock 1 The maximum recording time of all the folders is as follows. You can record messages for the maximum recording time in a single folder. 19 h. 35 min. 1 Press zXREC/PAUSE. 4 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. Maximum recording time SP** See “Selecting the Folder”. 1 Note on recording Noise may be recorded if an object, such as your finger, etc., accidentally rubs or scratches the unit during recording. HQ* Select the recording mode. zXREC/PAUSE Recording level is low. Recording level is unstable (when recording music, etc.). Blank space Battery life* Serial No. _____________________________________ ICD-P320 Selecting the Microphone Sensitivity • To record in better sound quality, select the HQ mode. For switching the recording mode, see “Changing the Recording Mode” on the reverse side. • Before making a long recording, be sure to check the battery indicator. • The maximum recording time and the number of messages you can make vary depending on the conditions of use. • When you record messages in the mixture of HQ, SP and LP mode, the maximum recording time will be between those for the HQ and LP modes. • Due to the limitation of the IC recording system, this unit records in the minimum recording unit of approx. 2 seconds at most, therefore the following symptoms may occur: – When a message is shorter than the minimum recording unit, it is still counted as approx. 2 seconds at most so the remaining recording time will decrease by more than the actual length of the message. – When the message is longer than the minimum recording unit, the remaining recording time will decrease by more than the actual length of the message if it cannot be divided by the minimum recording unit without a remainder. – The sum of the number on the counter (elapsed recording time) and the remaining recording time may be less than the unit’s maximum recording time. Playing Back Messages When playing back a previously recorded message, start from Step 1. When playing back a message you have just finished recording, start from Step 3. 1 Select the folder. See “Selecting the Folder”. 2 Select the message number. Press – . or >+ to display the desired message number. Selected message number – .: for smaller message number Number of messages in a folder >+: for larger message number Counter display* * The display selected with the DISPLAY/MENU button appears (see the reverse side). 3 Remaining memory indication Start playback. i (earphone) jack 1 Press NxPLAY/STOP. During recording, the remaining memory indicator decreases one by one. OPR indicator (lights in green during playback.) 2 Adjust the volume with the VOL control. The memory is nearly full. Counter display (or the selected display mode) Flashing When the remaining time of recording reaches 5 minutes, the last one of the indication flashes. If the remaining recording time display mode is selected, the remaining recording time display will also flash when the remaining time reaches 1 minute. When the memory is full, recording automatically stops and “FULL” will flash in the display window with an alarm sound. To continue recording, first erase some of the messages. Notes • If you press zXREC/PAUSE when the memory is full, “FULL” will flash with an alarm sound. Erase some of the messages before you start recording again. • If you press zXREC/PAUSE after you have recorded 99 messages, “FULL” will flash with an alarm sound. Select another folder or erase some of the messages. Starting recording automatically in response to the sound — Advanced VOR function When VOR (voice operated recording) is set to ON in the menu, recording starts when the recorder detects sound. (“VOR” is displayed in the display window.) Recording stops when no sound is heard. (“VOR PAUSE” flashes in the display window.) Note VOR function is affected by the sound around you. Set the microphone sensitivity to “H (high)” or “L (low)” using the menu. If recording is not satisfactory after you have changed the microphone sensitivity, or for important recording, set VOR to OFF. xSTOP After playing back one message, the unit stops at the beginning of the next message. When the continuous play function is set to “ON” (see the reverse side), the unit stops after playing all messages in a folder. When the last message on a folder has been played back, the unit stops at the beginning of the last message. For private listening Connect an ear receiver or headphones (not supplied) to the i (earphone) jack. The built-in speaker will be automatically disconnected. If noise is heard, wipe the headphones plug. Other operations To Do this stop at the current position Press NxPLAY/STOP or xSTOP. To resume playback from that point, press NxPLAY/STOP again. go back to the beginning of the current message Press – . once.* skip to the next message Press >+ once.* go back to previous messages/skip to succeeding messages Press – . or >+ repeatedly. (During stop mode, keep the button pressed to skip the messages continuously.) * These operations are for when EASY-S (Easy Search function) of the menu is set to “OFF”. Playing back a message repeatedly — Repeat Play During playback, press NxPLAY/STOP for more than one second. “ “ will be displayed and the selected message will be played back repeatedly. To resume normal playback, press NxPLAY/STOP again. To stop playback, press xSTOP. Playing back all messages in a folder continuously — Continuous Play You can select the continuous play mode with the CONT in the menu. When you set CONT to ON, you can play back all messages in a folder continuously. Searching forward/ backward during playback (Cue/Review) To search forward, keep >+ pressed during playback and release the button at the point you wish to resume playback. To search backward, keep – . pressed during playback and release the button at the point you wish to resume playback. If you keep >+ or – .pressed, the unit starts to search at higher speed. For the first 7 seconds of cue/ review, fast playback sound can be heard. When searching at a higher speed, playback sound will not be heard. During cue/review, the counter will be displayed, regardless of the display mode setting. 1 Tip When fast playback is done to the end of the last message, “END” flashes 5 times. (You cannot hear the playback sound.) If you keep – . pressed while “END” is flashing, the messages are played back rapidly, and normal playback will start at the point you release the button. When “END” stops flashing and the OPR indicator goes off, the unit will stop at the beginning of the last message. If the last message is long and you wish to start playback at a later part of the message, keep >+ pressed to play back the message to the end and then press – . while “END” is flashing to go back to the desired point. (For messages other than the last one, go to the beginning of the next message and play backward to the desired point.) Locating quickly the point you wish to start playback (Easy Search) When EASY-S is set to “ON” in the menu, you can advance approx. 10 seconds by pressing >+. This function is useful when locating a desired point in a long recording. (“EASY-S” is displayed in the display window.) BVarious Ways of Recording Erasing Messages Adding a Recording You can erase the recorded messages one by one or all messages in a folder at a time. Note that once a recording has been erased, you cannot retrieve it. At a factory setting, you cannot add a recording not to erase the message by accidental operation. If you want to add a recording to a previously recorded message or add an overwrite recording, change the REC-OP setting in the procedures below. 1 When a message is erased, the remaining messages will advance and renumbered so that there will be no space between messages. Before erasing Message 1 Message 2 Message 3 Message 4 Message 5 2 Erase Message 3 After erasing Message 1 Message 2 Message 3 Message 4 1 Press ERASE while playing back the message you want to erase or press ERASE for more than 1 second during stop mode. A beep will sound and the message number and “ERASE” will flash while the whole message is played back 10 times. To cancel erasing 3 Press xSTOP before step 2. To erase other messages Repeat steps 1 and 2. First divide the message and then follow the steps to erase the message. You can divide a message during recording or playback, so that the message is divided into two and the new message number is added to the divided message. By dividing a message, you can easily find the point you want to play back when you make a long recording such as a meeting. You can divide messages until the total number of messages in the folder becomes 99. While recording or playing back a message, press DIVIDE at the point you want to divide. Press – . or >+ to display “REC-OP” and press NxPLAY/ STOP. 4 Press – . or >+ to select “ON” and press NxPLAY/STOP. Folder B Message 1 Message 2 Message 3 Blank space Message 1 Message 2 Blank space Message 1 Message 2 1 Select the folder you want to erase using DISPLAY/MENU. (See “Selecting the Folder” on the front side.) Message 3 To cancel erasing Press xSTOP before step 3. After adding a recording Message 3 2 While pressing xSTOP, press ERASE for more than 1 second. “ALL ERASE” will flash for 10 seconds. Message 4 Message 3 Added recording When “OVER” is selected in the menu You can add an overwrite recording after the selected point in a recorded message. The part of the message after the selected point is deleted. The starting point of an overwrite recording Message 4 Message 3 The deleted part of Message 3 3 While the display is flashing, press ERASE. Message 3 Message 4 Added overwrite recording in Message 3 1 During playback, press and hold zXREC/PAUSE. Note “ALARM OFF (or ON)” will not appear and the alarm cannot be set if the clock has not been set or no message has been recorded in the selected folder. Message 1 2 Main unit 3 i (earphone) jack (microphone) jack OPR (operation) indicator VOL (volume) control* DIVIDE xSTOP HOLD zXREC (record) /PAUSE NxPLAY/STOP (ENTER)** – .(review/fast backward)/ >+ (cue/fast forward) (SELECT) Speaker * There is a tactile dot beside the control to show the direction to turn up the volume. **The button has a tactile dot. Connect a plug-in-power type microphone or other equipment to the (microphone) jack. Rear mini-plug (monaural) Display window Folder indication Microphone sensitivity Alarm indicator USB connector Selected message number Battery compartment REC DATE (recorded date) indication Hook for handstrap (not supplied) REMAIN indicator Remaining memory indicator External microphone (not supplied) Remaining battery indicator Recording mode indication REC (recording) indicator Repeat play indicator EASY-S (Easy Search) indicator Number of messages in a folder/Menu indication/Counter / Remaining time indication /Recording date indication /Current time indication / Messages When you connect an external microphone, the built-in microphone is automatically cut off. When a plug in power type microphone is connected, power is automatically supplied to the microphone from the IC recorder. When recording from other equipment (micromini-plug (monaural) phone) Audio connecting cable with attenuator (not supplied) EAR, EARPHONE, v or REC OUT mini-plug (stereo or monaural) Tape recorder, TV, radio, etc. 2 Message 4 5 Press NxPLAY/STOP. “DATE” will flash in the display window. Press –. or >+ to display the message number as the divided messages each have message numbers. 1 To play the divided messages continuously Select ON for CONT in the menu as described in “Playing Back All Messages in a Folder Continuously”. 3 Notes 1 Press NxPLAY/STOP while “DATE” is flashing. The year digits will flash. 3 3 Press – . or >+ to select the month digits and press NxPLAY/STOP. The day digits will flash. 4 Press – . or >+ to select the day digits. Follow the steps in “Recording Messages” on the front side to record messages. Notes • Make sure that the plugs are connected securely. • We recommend you make a trial recording to check the connections and volume control. • When connecting equipment other than Sony’s, refer to the instruction manual of the equipment. Press – . or >+ to select the day of the week. To play back at the same time every day Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. 5 Press – . or >+ to select the folder to which you want to move the message (C in this case). Press – . or >+ to select “DAILY”. 4 Preventing Accidental Operation — HOLD function Slide the HOLD switch to “ON”. “HOLD” will flash three times, indicating that all the functions of the buttons are locked. When the HOLD function is activated during stop, all the display will be turned off after “HOLD” flashes. A beep will sound to indicate that operation has been accepted. BEEP OFF: No beep sound will be heard except for the alarm and timer. 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. 2 Press – . or >+ to display “BEEP ON (or OFF)” and press NxPLAY/STOP. “ON (or OFF)” will flash. 3 4 Note When the HOLD function is activated during recording, cancel the HOLD function first to stop recording. Even if the HOLD function is activated, you can stop the alarm playback. To stop the alarm or playback, press xSTOP. Press NxPLAY/STOP. 1 On the current time display If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting. Set the alarm time. 1 Press – . or >+ to select the hour digits and press NxPLAY/STOP. The minute digits will flash. HQ: You can record with the high quality sound (monaural sound). SP: You can record with better sound (monaural sound). LP: You can record for longer time (monaural sound). 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. 2 Make sure that “MODE” is displayed and press NxPLAY/ STOP. “HQ (or SP, LP)” will flash. 3 Press – . or >+ to select “HQ”, “SP” or “LP” and press NxPLAY/STOP. 4 Press xSTOP to exit the menu mode. The setting becomes effective and the normal screen will be displayed. If the unit is left unoperated for more than 3 seconds, the display will show the current time and the selected recording mode will be displayed. Playing Back All Messages in a Folder Continuously CONT ON: You can play back all messages in a folder continuously. CONT OFF: Playback stops at the end of each message. 1 2 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. Press – . or >+ to display “CONT” and press NxPLAY/ STOP. “OFF (or ON)” will flash. 3 Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. Now the setting is completed. 4 Press xSTOP to exit the menu mode. 2 Press – . or >+ to select the minute digits and press NxPLAY/STOP. “B-PLAY” will be displayed. 6 Set the alarm sound. 1 Press – . or >+ to select the alarm sound either from “B-PLAY” (playing back the message after the alarm) or “B-ONLY” (alarm only) Press xSTOP before step 5. 2 Press NxPLAY/STOP. “ALARM ON” will be displayed. Note 7 m Remaining time (REMAIN): In the playback mode: The remaining time of one message indication. In the stop and recording mode: The remaining recording time indication. m Recorded date (REC DATE)*: The date the current message was recorded. m Recorded time (REC DATE)**: The time the current message was recorded. Turning off the OPR Indicator (LED) During recording and playback, the OPR (operation) indicator lights or flashes. You can set the OPR indicator to turn off even in operation. 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. 2 Press – . or >+ to display “LED” and press NxPLAY/STOP. “ON (or OFF)” will flash. 3 Press xSTOP to exit the menu mode. “,” is displayed when the number of the message with alarm setting is selected. At the set time, the alarm will sound for about 10 seconds and the selected message will be played back. (If you have selected “B-ONLY”, only the alarm will sound.) During playback, “ALARM” will flash in the display window. When the playback ends, the unit will stop automatically at the beginning of that message. To listen to the same message again Press NxPLAY/STOP. The same message will be played back from the beginning. Press – . or >+ to select “OFF” and press NxPLAY/STOP. Now the setting is completed. * If the clock has not been set, “--Y--M--D” will be displayed. **If the clock has not been set, “--:--” will be displayed. To USB connector of your computer Changing the Recording Mode time in one message 5 To USB connector of IC recorder Connecting cable (supplied) Selecting the Display Mode You can select the display mode for the stop, recording and playback modes. Each time you press DISPLAY/MENU, the display mode will change as shown below: By connecting the IC recorder to your computer with the supplied USB cable, you can use the “Digital Voice Editor” software to do the following: • Saving the IC recorder messages on your computer’s hard disk. • Transferring the PC messages back to the IC recorder. • Playing or editing the messages on your computer. • Sending a voice e-mail message using MAPI e-mail software. For the details, see the supplied “Digital Voice Editor 2” software operating instructions. Press xSTOP to exit the menu mode. To cancel the HOLD function Slide the HOLD switch to “OFF” . Using the ”Digital Voice Editor“ Software Connection Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. The setting is completed. HOLD Counter: To cancel moving the message(s) The move function does not duplicate a message in another folder. When you move a message to another folder, the one in the previous folder will be deleted. 1 Select the message you set the alarm to play back, and press DISPLAY/MENU for more than 1 second to enter the menu mode. 2 Press – . or > + to select “ALARM ON”. 3 Press NxPLAY/STOP to flash “ON”. 4 To cancel the alarm setting: Press – . or > + to flash “OFF” and press NxPLAY/STOP. To change the alarm setting: Press NxPLAY/STOP. When the alarm date is displayed, follow the Steps 3 to 6 of “Playing Back a Message at a Desired Time with an Alarm” to change the alarm setting. 5 Press xSTOP to exit the menu mode. BEEP ON: B Elapsed playback/recording Press NxPLAY/STOP. Press xSTOP to exit the menu mode. To cancel or change the alarm setting The hour digits will flash. The message is moved in the destination folder. 6 • You cannot set the alarm if you have not set the clock or there is no message in the selected folder (the unit will not enter the alarm setting mode when you press DISPLAY/ MENU in Step 2). • If you try to set the alarm to play back a message at a previously set time on another message, “PRE SET” will be displayed, preventing new settings. • If the alarm time comes while another message is being played back with an alarm, the playback stops and the new message will be played back. • If the alarm time comes during recording, alarm will sound for 10 seconds after the recording is finished and playback begins. “,” will flash when the alarm time comes. • If more than one alarm time comes during recording, only the first message will be played back. • When the alarm time comes when the unit is in the menu mode, alarm will sound and the menu mode will be canceled. • If you erase the message you set the alarm to play back, the alarm setting will be canceled. • If you divide a message with the playback alarm, playback will stop at the point you divided a message. • You can adjust the playback volume with the VOL control. • If the alarm time comes during erasing, alarm will sound for 10 seconds after the erasing is finished and playback begins. • Alarm setting will not be canceled when the alarm playback finishes. To cancel alarm setting, see below. Turning off the Beep Sound To play back once a week The destination folder indication flashes. 4 Notes 1 Tip While the unit is stopped, select the message you want to move. Press – . or >+ to select “MOVE” and press NxPLAY/ STOP. Press xSTOP while the alarm sound is heard. You can stop even when the HOLD function is activated. 2 Press – . or > + to select the year digits and press NxPLAY/STOP. The month digits will flash. Moving Messages to a Different Folder — Move Function 2 To cancel the alarm setting before the playback starts Now the setting is completed. Set the alarm date. To play back on a desired date (the message will be played back at the same time on the same date every year until you erase the message) • If 99 messages have been recorded in a folder, you cannot divide a message. In that case, reduce the number of messages to 98 or less by erasing unnecessary messages or by moving some of the messages to another folder before dividing a message. • If you divide a message with an alarm setting, the alarm setting remains only with the former message divided. • You cannot divide a message in the first or the last 1 second. • If you divide a message frequently, the unit may become unable to divide a message. • Once a message is divided, you cannot combine the divided messages with the IC recorder. To combine the divided messages, use the supplied applicatio software. When recording with an external microphone (microphone) Message 3 To play the divided message Press xSTOP to stop the recording. Recording with an External Microphone or from Other Equipment 1 Message 2 The message numbers increase. While the “ADD” or “OVER” flashes, press zXREC/PAUSE again. • You cannot add or overwrite a recording if the remaining memory is not long enough. • The added or overwritten portion of a message will be recorded in the same recording mode (HQ, SP, or LP). ERASE DISPLAY/MENU 4 Press – . or >+ to select “ON”. “ON” starts to flash. A message is divided. Message 1 1 Notes Display window Message 3 Example: Moving Message 3 in Folder A to Folder C The OPR indicator will light in red. An add or overwrite recording starts. MIC (built-in microphone) Message 2 3 Press NxPLAY/STOP. “OFF” starts to flash. You can move the recorded messages to another folder. The “REC” indication appears. “ADD” or “OVER” will flash and the unit stops in the recording pause mode. Index to Parts and Controls 2 Press – . or >+ to select “ALARM OFF” (If the alarm has already set to the selected message, “ALARM ON” is displayed. If you do not wish to change the setting, press xSTOP and exit the menu mode.) 1 Tip In step 3 , select “OFF” and press NxPLAY/STOP. You can add a recording to the message being played back. When “ADD” is selected in the menu The added recording will be placed after the current message and counted as a part of the message. During Message 3 Message 4 playback of Message 3 Enter the alarm setting mode. 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. • When you press DIVIDE during playback: The message is divided into two at the point you pressed the button, and the new message number and “DIVIDE“ flash three times. The message numbers of the following messages will increase by one. Press xSTOP to exit the menu mode. Select the folder (See “Selecting the Folder” on the front side) and display the message you want to play back with an alarm. You can divide a message during recording pause. Adding a Recording to a Previously Recorded Message e.g. Folder A 2 A message is divided. Recording continues Press – . or >+ to select “ADD” or “OVER” and press NxPLAY/STOP. To prohibit to add a recording Erasing all messages in a folder 1 Message 1 Message 2 Message 3 •ADD: adds a recording to a previously recorded message •OVER: adds an overwrite recording. 5 You can sound an alarm and start playback of a selected message at a desired time. If you select “B-ONLY” in Step 6, an alarm sounds only and playback will not start. • When you press DIVIDE during recording: The new message number is added at the point you pressed the button, and the new message number and “DIVIDE“ flash three times. The message will be divided into two; however, the messages will be recorded without a break. The setting is changed. To erase a message partially 2 Press ERASE while the message is being played back. The message is erased and the remaining messages will be renumbered. (For example, if you erase Message 3, Message 4 will be renumbered as Message 3. When erasing is completed, the unit will stop at the beginning of the following message.) Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. The adding recording window will be displayed. Remaining messages are renumbered. Playing Back a Message at a Desired Time with an Alarm Dividing a Message Using an Adding Recording Erasing messages one by one BOther Functions 4 Press xSTOP to exit the menu mode. Precautions On power • Operate the unit only on 3 V DC. Use two LR03 (size AAA) alkaline batteries. On safety • Do not operate the unit while driving, cycling or operating any motorized vehicle. On handling • Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Should any solid object or liquid fall into the unit, remove the batteries and have the unit checked by qualified personnel before operating it any further. On noise • Noise may be heard when the unit is placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback. • Noise may be recorded when an object, such as your finger, etc., rubs or scratches the unit during recording. On maintenance • To clean the exterior, use a soft cloth slightly moistened in water. Do not use alcohol, benzine or thinner. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Backup recommendations To avoid potential risk of data loss caused by accidental operation or malfunction of the IC recorder, we recommend that you save a backup copy of your recorded messages on a tape recorder, etc. Specifications Recording media Built-in flash memory 64 MB, Monaural recording Recording time HQ: 7 hours 20 minutes SP: 19 hours 35 minutes LP: 32 hours 10 minutes Frequency range HQ: 260 Hz - 6,800 Hz SP/LP: 220 Hz - 3,400 Hz Speaker approx. 2.8 cm (1 1/8 in.) dia. Power output 250 mW Input/Output •Earphone jack (minijack) for 8 - 300 ohms ear receiver/headphones •Microphone jack (minijack, monaural) Plug in power Minimum input level 0.6 mV 3 kilohms or lower impedance microphone •USB connector Power requirements Two LR03 (size AAA) alkaline batteries: 3 V DC Dimensions (w/h/d) (not incl. projecting parts and controls) 34.6 × 109.5 × 18.0 mm (1 3/8 × 4 3/8 × 23/32 in.) Mass (incl. batteries) 68 g (2.4 oz) Supplied accessories Operating instructions (for the IC recorder (1)/ for the application software (1)) LR03 (size AAA) alkaline batteries (2) (for the U.S.A. and Canada only) Headphone (1) (excluding the U.S.A., Canada and Europe) Carrying pouch (1) (excluding the U.S.A., Canada and Europe) USB connecting cable (1) Application software (CD-ROM) (1) Optional accessories Electret Condenser Microphone ECM-DM5P, ECM-CZ10, ECM-Z60, ECM-TL1 (for telephone recording) Audio connecting cable RK-G64HG /RKG69HG (excluding Europe) Active speaker SRS-T88, SRS-T80 Your dealer may not handle some of the above listed optional accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2006:02:16 12:00:23Z Modify Date : 2006:02:16 21:05:07+09:00 Subject : Page Count : 2 Creation Date : 2006:02:16 12:00:23Z Mod Date : 2006:02:16 21:05:07+09:00 Producer : Acrobat Distiller 5.0.5 for Macintosh Author : Sony Corporation Keywords : Metadata Date : 2006:02:16 21:05:07+09:00 Creator : Sony Corporation Title : ICD-P320 Description :EXIF Metadata provided by EXIF.tools