For XDCAM, sent in a format like “200 MXF DISK 1” (“200” is a response code). SITE UMMD When C*.MXF file is sent with the STOR command, the copy source UMID is saved if this command is invoked immediately before the STOR command. SITE DF a) Acquires the amount of free disc space. SITE DF 6-3 FTP File Operations SITE UMMD Command name SITE CHMOD a) Description Command syntax Locks and unlocks clips. Also sets permissions for directories and files in the General directory. SITE CHMOD Specify one of the following values in , according to the specification in . • When a clip is specified in 444: Lock. 666: Unlock. • When a directory in the General directory is specified in 555: Forbid writing to the directory. 777: Allow writing to the directory. • When a file in the General directory is specified in 444: Forbid writing to and execution of the file. 555: Forbid writing to the file, but allow execution. 666: Allow writing to the file, but forbid execution. 777: Allow writing to and execution of the file. Input example: SITE CHMOD 444 Clip/C0001.MXF (Lock clip C0001.MXF) a) This is supported from firmware version 1.5. Chapter 6 File Operations 6-3 FTP File Operations 87 6-4 Recording Continuous Time Code With FAM and FTP Connections When you are connected to the unit by FAM or FTP, you can create new clips with time code that is continuous with the time code of the last frame of the last clip on the disc. To record continuous time code, first set the INT/EXT/ RP188 switch to INT, set the PRESET/REGEN switch to REGEN, and set extended menu item 629 “TC SELECT” to “tc.” Then proceed as follows. Note Continuous time code cannot be recorded if extended menu item 629 “TC SELECT” is set to “vitc.” See 7-3-2 “Extended Menu Operations” (page 108) for more information about how to make extended menu settings. Chapter 6 File Operations FAM connection Write clip files to the unit from the computer or other device that is connected to this unit. FTP connection Use the “STOR” command to transfer clip files from the computer that is connected to this unit. If you issue the “SITE UMMD” command immediately before the “STOR” command, the original time code of the transferred file is recorded, regardless of the settings of the INT/EXT/RP188 switch and the PRESET/REGEN switch. 88 6-4 Recording Continuous Time Code With FAM and FTP Connections Menus 7-1 Menu System Configuration The settings for this unit use the following menus. • Setup menu See the next item. • Maintenance menu This provides audio control, and network and setup menu settings, and also shows version information. For details, see 7-4 “Maintenance Menu” (page 112). • System menu This provides disc formatting, date setting, and similar operations. For details, see 7-5 “System Menu” (page 117). Setup menu The setup menu system of this unit comprises the basic setup menu (also referred to simply as “basic menu”) and extended setup menu (also referred to simply as “extended menu”). • Basic menu This menu is used to make settings relating, for example, to the following. - the digital hours meter - the preroll time - the text information superimposed on the video output to the monitor - the menu banks for retaining menu settings • Extended menu This menu is used to make a wide range of settings relating to the functions of this unit, for example, the control panel functions, video and audio control, and digital data processing. Configuration of the basic setup menu The basic setup menu comprises the following groups of items. Chapter 7 Item group Function Refer to Items H01 to H15 Display of the total number of hours the unit has been powered on, and other information collected by the digital hours meter page 120 Items 001 to 099 Settings relating to the preroll page 90 time, superimposed text information, switching between 525(U) line, 525(J) line and 625 line operation modes, etc. Items B01 to B20 Settings relating to the menu page 93 banks for saving menu settings Configuration of the extended setup menu The extended setup menu comprises the following groups of items. Item group Function Refer to Items 100 to 199 Settings relating to control panels page 97 Items 200 to 299 Settings relating to the remote control interface page 98 Items 300 to 399 Settings relating to editing operations page 99 Items 400 to 499 Settings relating to preroll page 100 Items 500 to 599 Settings relating to disc protection page 101 Items 600 to 699 Settings relating to the time code, metadata, and UMID page 101 Items 700 to 799 Settings relating to video control page 103 Items 800 to 899 Settings relating to audio control page 106 Items 900 to 999 Settings relating to digital processing page 108 7-1 Menu System Configuration 89 7-2 Basic Setup Menu 7-2-1 Items in the Basic Setup Menu The basic menu items (excluding the items related to the digital hours meter) are listed in the following table. • Item names are the names which appear in the video panel and on an external monitor, when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector. An abbreviated name appears in the time data display section when you press the NEXT button. • The values in the Settings column are the values which appear in the time data display section. (The values may appear in a different format in the video panel and on an external monitor. In this case, the video panel values are shown in parentheses.) Underlined values are the factory defaults. Item number Item name Settings 001 PREROLL TIME 0 s (0 sec)... 5 s (5 sec)... 30 s (30 sec): Set the preroll time to between 0 and 30 seconds in steps of 1 second. A preroll time of at least 5 seconds is recommended when using this unit for editing. 002 CHARACTER H-POSITION Adjust the horizontal screen position (as a hexadecimal value) of the text information displayed on the monitor. a) 00... 0A ...2A (525(U)/525(J) line modes) /00... 09 ...29 (625 line mode): The hexadecimal value 00 is for the far left of the screen. Increasing the value moves the position of the characters to the right. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Set this item by adjusting to the required position while viewing the monitor. 003 CHARACTER V-POSITION Chapter 7 Menus Adjust the vertical screen position (as a hexadecimal value) of the text information displayed on the monitor. a) 00... 2E ...38 (525(U)/525(J) line modes)/00... 37 ...43 (625 line mode): The hexadecimal value 00 is for the top of the screen. Increasing the value lowers the position of the characters. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Set this item by adjusting to the required position while viewing the monitor. 005 DISPLAY INFORMATION SELECT Determine the kind of text information to be displayed on the monitor. a) off (display off): Do not output text information. T&sta (time data & status) : Time data and the units status. T&UB (time data & UB): Time data and user bit data. (When UB (user bit data) is selected with the COUNTER SEL button, the user bit data and time data arranged in that order are displayed.) T&CNT (time data & CNT): Time data and counter count. (When COUNTER is selected with the COUNTER SEL button, the counter count and time data arranged in that order are displayed.) T&T (time data & time data): Time data and time code (TC or VITC). T&clp (time data & clip name): Time code and clip name time (time data only): Time data only. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) 90 7-2 Basic Setup Menu Item number Item name Settings 006 LOCAL FUNCTION ENABLE Determine which recording and playback control buttons on the control panel are enabled when this unit is controlled from external equipment. dis (all disable): All buttons and switches are disabled. st&ej (stop & eject) : Only the STOP button and EJECT button are enabled. ena (all enable): All buttons and switches are enabled. 007 TAPE TIMER DISPLAY Determine whether to display the counter in 12-hour mode or 24-hour mode. + –12H (+ /–12H) : 12-hour mode 24H: 24-hour mode 009 CHARACTER TYPE Determine the type of characters such as time code displayed on the monitor. a) white: White letters on a black background. black: Black letters on a white background. W/out: White letters with black outline. B/out: Black letters with white outline. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Set this item by selecting the required type while viewing the monitor. 011 CHARACTER V-SIZE Determine the vertical size of characters such as time code displayed on the monitor. a) ×1 :Standard size ×2 :2 times standard size a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Set this item by selecting the required size while viewing the monitor. 012 CONDITION DISPLAY ON VIDEO MONITOR Select whether to display disc condition marks on the monitor. a) dis (disable): Do not display. ena (enable): Display. Chapter 7 Menus a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) 013 525/625 SYSTEM SELECT Specify whether to enable switching between 525(U) line, 525(J) line and 625 line modes. off: Do not enable system switching. on: Enable system switching. For the switching between 525(U)/525(J)/625 line modes, see page 95. Note When you switch line modes, all basic menu and extended menu items are set to the factory defaults for the selected line mode. 015 LCD CHARACTER TYPE Specify the type of characters used to display information on the monitor a) when the STATUS button is pressed. W/out: White letters with black outline. white: White letters on a black background. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Set this item by selecting the required type while viewing the monitor. 7-2 Basic Setup Menu 91 Item number Item name Settings 016 Select whether or not to display alarm messages. off: Do not display alarm messages. (However, certain important alarms are displayed). limit (on (limited)): Display only a minimum number of alarm messages. on: Display all alarm messages. ALARM DISPLAY For details about alarm message display conditions, see 8-4-1 “Alarm List” (page 122). 017 SUB STATUS DISPLAY SELECT Determine the kind of sub status information to be displayed on the monitor. a) off: Do not output sub status information. rmain (disc remain): Available disc space (unit: minute) clip (clip no): Order of playback of the selected clip/total number of clips posi (playback position): Playback position within clip pbr (playback remain): The remaining playback time of the selected clip from the current playback position (hours:minutes:seconds:frames). a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Note When menu item 005 is set to “off,” sub status information is not displayed when this item is set to anything other than “off.” 024 MENU CHARACTER TYPE Determine the type of characters in menu text displayed on the monitor. a) white: White letters on a black background. black: Black letters on a white background. W/out: White letters with black outline. B/out: Black letters with white outline. a) Video panel and external monitor (when the input signals to the monitor are the video signals output from the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector) Chapter 7 Menus Set this item by selecting the required type while viewing the monitor. 029 STORED OWNERSHIP Specify whether to enable changing UMID ownership information settings (COUNTRY, ORGANIZATION and USER). off: Do not enable. on: Enable. 031 RECORDING FORMAT Select the recording format. IMX50 (IMX 50Mbps): MPEG IMX 50 Mbps IMX40 (IMX 40Mbps): MPEG IMX 40 Mbps IMX30 (IMX 30Mbps): MPEG IMX 30 Mbps DVCAM: DVCAM 032 LCD MONITOR MODE Set the aspect ratio for the video panel. auto: the aspect ratio of the display screen automatically adjusts to the aspect ratio of the input material. 16:9: set the aspect ratio to 16:9. 4:3: set the aspect ratio to 4:3. 034 MENU STATUS DISPLAY ON VIDEO MONITOR Specify whether to display the setup menu status at the left edge of the status display line when basic menu item 005 “DISPLAY INFORMATION SELECT” is set to “T&sta.” dis (disable): Do not display. ena (enable): Display. (The display is visible only when no disc is loaded, and during insertion and ejection of a disc.) See 7-3-3 “Using UMID Data” (page 109) for more information about UMID. 92 7-2 Basic Setup Menu Item number Item name Settings 035 Specify whether or not to allow user definition of the titles assigned to clips. off: Do not allow assignment. on: Allow assignment. CLIP TITLE NAMING SELECT Sub-item 036 See 6-1-3 “Assigning User-Defined Clip Titles” (page 75) for more information about assigning titles. 1 TITLE Specify whether to assign titles to recorded clips. disable: Do not assign titles to clips. enable: Assign titles to clips. 2 PREFIX Set the prefix of the title (up to 10 characters). The allowable characters are alphanumeric characters, symbols (! # $ % & ' ( ) + , - . ; = @ [ ] ^ _ { } ~), and the space character. TITLE 3 NUMERIC Set the initial value of the numeric part of the title (00001 to 99999, five-digit number). 00001 FILE NAMING a) Sub-item Specify whether to allow use of clip and clip list files with user-defined names. See 6-1-4 “Assigning User-Defined Clip and Clip List Names” (page 76) for details about how to make the settings. 1 NAMING FORM Specify the clip and clip list naming format. (Specify whether to allow use of files with user-defined names.) C****: Standard format (Do not allow use of files with user-defined names) free: Free format (Allow use of files with user-defined names) 2 AUTO NAMING When “free” is selected under the sub-item “NAMING FORM,” specify whether to use the standard format name or the same name as the title for clips recorded on this unit. C****: Use the standard format for clip names. title: Use the title set in basic menu item 035 “CLIP TITLE NAMING SELECT” for clip names. RECALL SETUP BANK-1 Set to “on” to recall menu settings from menu bank 1. B02 RECALL SETUP BANK-2 Set to “on” to recall menu settings from menu bank 2. B03 RECALL SETUP BANK-3 Set to “on” to recall menu settings from menu bank 3. B11 SAVE SETUP BANK-1 Set to “on” to save current menu settings to menu bank 1. B12 SAVE SETUP BANK-2 Set to “on” to save current menu settings to menu bank 2. B13 SAVE SETUP BANK-3 Set to “on” to save current menu settings to menu bank 3. B20 RESET SETUP MENU Set to “on” to return the settings of the current menu to the factory default settings. Set to “bank-4” to set the current menu to the settings saved in menu bank 4. off on (on (default)): Return the current menu to the factory default settings. bank-4: Set the current menu to the settings saved in menu bank 4. Chapter 7 Menus B01 a) This is supported from firmware version 1.5. 7-2 Basic Setup Menu 93 7-2-2 Basic Menu Operations Display in video panel and on external monitor Cursor indicating the currently selected item Basic setup menu operations Group name for the currently selected item This section explains how to select setup menu items and how to change their values. The operations are common to both the basic menu and the extended menu. ------- HOUR METER *HO1 : OPE HOURS H11 : OPE HOURS r- Time data display Video panel DATA dB OVER 0 DATA DATA dB OVER 0 dB OVER 0 DATA VITC VITC VIUB COUNTER HOLD PB NDF EXT-LK dB OVER 0 -12 -12 -12 -12 -20 -20 -20 -20 -30 -40 -30 -40 -30 -40 -30 -40 HOURS MINUTES -60 -60 -60 -60 DISC E B BATT E F CH- 15 CH- 26 CH- 37 AUDIO INPUT CH INPUT SEL CH- 48 VIDEO INPUT SEL KEY INHI WARNING SECONDS PROCESS CONTROL STATUS CHARACTER REC INHI OFF ON FRAMES LIGHT OFF ON Display in time data display MONITOR OFF L H 1,5 5 4 Item number (flashing) TC KEY INHI ON NETWORK LOCAL REMOTE OFF ACCESS ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN COUNTER SEL HOLD SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK METER SEL MONITOR SEL MENU PLAY SHUTTLE RP188 REGEN CH-3 R-RUN CH-4 L/ST/R NEXT STOP SYSTEM MENU SET RESET F REV F FWD To display the item name in the time data display Hold down the NEXT button. S.SEL MARK1 REC OUT IN TOP END 2 MARK2 3 Chapter 7 Menus Press the MENU button. The setup menu appears in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. A cursor indicates the currently selected menu item. The item number and current setting (elapsed time in the case of the digital clock) of the currently selected menu item also appear in the time data display section. The item number flashes to indicate that you can switch to another item. 94 7-2 Basic Setup Menu Rotate the jog dial or shuttle dial to select a menu item. Rotate in the clockwise direction to select higher numbers, and in the counterclockwise direction to select lower number. The cursor moves in the direction of the rotation (the screen scrolls when the cursor reaches the top or bottom of the screen). The speed at which the cursor moves and speed with which menu items change vary with the rotation speed of the jog dial or the rotation angle of the shuttle dial. The STOP button lights when you select an item that contains sub items. 2 NEXT button 1 Setting JOG SHIFT EXT CH-2 AUDIO PREV 109 109 3 When the selected item contains sub items, you can select a sub item by holding down the STOP button and rotating the jog dial or shuttle dial. The displays in the video panel, on an external monitor, and in the time data display section change as shown below when you hold down the STOP button. In the time data display section, the currently selected sub item number flashes to indicate that you can switch to another sub item. To abandon making a change Press the MENU button before pressing the SET button. The menu display disappears from the video panel, the external monitor, and the time data display section without the new setting value being saved. Display in video panel and on external monitor Cursor indicating the currently selected sub-item ITEM-703 BLANK LINE SELECT ALL LINE LINE 12 - --blnk ---- * Resetting the menu settings to their factory default values To reset the current active menu settings to their factory default values, proceed as follows. 1 Display in time data display TC KEY INHI NETWORK ON LOCAL REMOTE OFF ACCESS ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN REGEN R-RUN 3 2 COUNTER SEL HOLD RP188 CH-2 CH-3 CH-4 METER SEL MONITOR SEL L/ST/R AUDIO Sub-item number (flashing while changing) PREV PLAY SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC OUT IN TOP F REV JOG SHIFT EXT F FWD END MARK2 4 With the SHUTTLE button held down, rotate the jog dial or shuttle dial to change the setting. The displays in the video panel, on an external monitor, and in the time data display section change as shown below when you hold down the SHUTTLE button. In the time data display section, the currently selected setting value flashes to indicate that you can change it to another value. 1 Press the MENU button. The menu appears in the video panel, on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input, and in the time data display section. 2 Press the RESET button. Chapter 7 Menus Display in video panel and on external monitor The message “INITIALIZE ALL ITEMS TO FACTORY PRESET VALUES?” appears in the video panel and on the external monitor. The message “Init setup?” appears in the time data display. Setting value ITEM-001 PREROLL TIME To abandon operations and return to the setup menu display Press the RESET button again. 5 sec 3 Press the SET button. The menu settings are reset to their factory default settings. Display in time data display Switching between 525(U) line, 525(J) line and 625 line modes (menu item 013) Setting value (flashing while changing) 5 Press the SET button. This saves the new setting value, and the menu display disappears from the video panel, the external monitor, and the time data display section. To switch between 525(U) line, 525(J) line and 625 line operation modes, proceed as follows. 1 Press the MENU button. 2 Turn the jog dial or shuttle dial to display menu item 013 in the time data display. 7-2 Basic Setup Menu 95 3 4 5 Hold down the SHUTTLE button, and turn the jog dial or shuttle dial to set menu item 013 to “on.” Recall Current active menu settings Press the SET button. Save Menu bank 1 Hold down the SHUTTLE button, and turn the jog dial or shuttle dial to select the line mode 525(U), 525(J) or 625. Recall 6 Press the SET button. Save 7 Menu bank 2 Turn the unit off (press the on/standby switch to put the unit in the standby state). Next time the unit is turned on (when the unit is put in the operating state by pressing the on/standby switch), it operates in the new mode. Recall Menu bank 3 Save Menu bank operations (menu items B01 to B13) Recall This unit allows menu settings to be saved in what are termed “menu banks.” Saved sets of menu settings can be recalled for use as required. To jump to menu item B01 You can recall any required menu by turning the jog dial or shuttle dial after pressing the MENU button. If you press the MENU button first, then the COUNTER SEL button, you can jump directly to menu item B01 or H01. The recalled menu item toggles between B01 and H01 every time you press the COUNTER SEL button. Chapter 7 Menus Saving the current active menu settings Set one of basic menu items B11 “SAVE SETUP BANK1” to B13 “SAVE SETUP BANK-3” to “on,” depending on which of the menu banks you wish to save in, then press the SET button. Recalling settings from a menu bank Set one of basic menu items B01 “RECALL SETUP BANK-1” to B03 “RECALL SETUP BANK-3” to “on,” depending on which of the menu banks you wish to recall from, then press the SET button. To recall menu bank 4, select “bank-4” under menu item B20 “RESET SETUP MENU.” Refer to the maintenance manual for more information about menu bank 4. Menu bank 4 Save Note The following message appears if the line mode of the menu bank that you are about to recall differs from the current line mode. Display in the video panel and on an external monitor ITEM-B01 RECALL SETUP BANK-1 System will be changed. Are you sure you want to execute? EXECUTE : SET KEY ABORT : MENU KEY Message in time data display Press the SET button to recall the settings and switch to the line mode saved in the menu bank. When you power the unit off and then on again, it will use the line mode and settings of the selected bank. To cancel the recall, press the MENU button. 96 7-2 Basic Setup Menu 7-3 Extended Menu 7-3-1 Items in the Extended Menu The following tables show the items in the extended menu. • Item names are the names which appear in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. An abbreviated name appears in the time data display section when you press the NEXT button. • The values in the Settings columns are the values which appear in the time data display section. (The values may appear in a different format in the video panel and on an external monitor. In this case, the video panel values are shown in parentheses.) Underlined values are the factory defaults. Menu items in the 100s, relating to the control panels Settings 101 SELECTION FOR SEARCH DIAL ENABLE Select how the unit enters the shuttle or jog mode. dial (dial direct): Press the SHUTTLE or JOG button or, except during recording/editing, turn the jog dial or shuttle dial. key (via search key): Press the SHUTTLE or JOG button. 105 REFERENCE SYSTEM ALARM Select whether or not to display a warning when the reference video signal is not supplied or is out of phase with the input video signal. off: No warning. on: Flash the STOP button as a warning. 107 REC INHIBIT LAMP FLASHING Select whether or not to flash the REC INHI indicator when recording is prevented (see “REC INHI (recording inhibited) indicator” on page 18). off: Light the REC INHI indicator. on: Flash the REC INHI indicator. 108 AUTO EE SELECT When a disc is inserted, select the operation modes in which input video and audio signals are automatically handled in E-E mode. S/F/R (stop/f.fwd/f.rev): In stop/fast-forward/fast-reverse modes stop: In stop mode off: Do not put the unit into E-E mode automatically. 109 FORCED EE WHEN DISC UNLOAD When “off” is selected in menu item 108, during disc loading/unloading and when no disc is inserted, select whether or not to control the output signal PB/EE setting. on: Do not control (the signal is always an E-E signal). off: Control. 114 AUDIO MONITOR OUTPUT LEVEL When “moni” is selected in menu item 820, select whether or not to control the level of the audio signal output from the AUDIO OUT 1/3, 2/4 connectors with the volume control knob for the PHONES jack. var (variable): Control. fixed: Do not control. 118 KEY INHIBIT When the KEY INHI switch is set to ON, select which buttons can be operated. The following sub-items control different sets of buttons independently. Sub-item 121 1 MON./INPUT SEL Select whether the AUDIO MONITOR SEL, the AUDIO METER SEL, the AUDIO INPUT CH, and the VIDEO INPUT SEL buttons are enabled. dis: Disabled. ena: Enabled. 2 CONTROL PANEL Select whether all switches and buttons other than the buttons specified with sub-item 1 and the MENU button are enabled. dis: Disabled. ena: Enabled. FRAME PB MODE Chapter 7 Menus Item number Item name Specify the frame mode for variable speed playback. field: Field playback frame: Frame playback. Compared to field playback, frame playback gives still pictures with higher precision. 7-3 Extended Menu 97 Menu items in the 100s, relating to the control panels Item number Item name Settings 131 AUDIO VOLUME Select whether each of the ALL/CH-1, CH-2 to CH-4 adjustment knobs on the control panel is effective to control the audio recording level and playback level on each channel or the ALL/CH-1 adjustment knob alone functions as a master control to control the audio level on all channels together. each: Each of the ALL/CH-1, CH-2 to CH-4 adjustment knobs is effective to control each channel. all: The ALL/CH-1 adjustment knob alone functions as a master control. When “all” is selected, the ALL indicator to the right of the ALL/CH-1 adjustment knob lights up. 142 REPEAT MODE Put the unit into repeat playback mode, or exit from repeat playback mode. off: Exits from repeat playback mode. play: Puts the unit into repeat playback mode. 143 INDEX PICTURE POSITION Select the frame of the clip to use as the thumbnail image (index picture) when recording. 0sec to 10sec: Can be set in the range from 0 seconds (first frame of the clip) to10 seconds, in units of 1 second. 145 MODE KEY ENABLE DURING RECORDING Specify whether only the STOP button stops recording. ena (all enable): Recording stops when the EJECT button is pressed a) and when the PLAY, STOP, SHUTTLE, and JOG buttons are pressed. b) stop: Recording stops only when the STOP button is pressed. a) The disc is ejected after recording stops. b) The unit enters stop mode when the PLAY button is pressed, and enters still image mode (jog/shuttle mode) when the SHUTTLE or JOG button is pressed. 146 POWER SAVE MODE Chapter 7 Menus Specifies whether to put the unit into power save mode. off: Do not put the unit into power save mode. on: Put the unit into power save mode. The following operations take slightly longer to start in power save mode. • Recording, playback, jog and shuttle mode playback, search • Display of the thumbnail screen and essence marks Menu items in the 200s, relating to the remote control interface Item number Item name Settings 214 REMOTE INTERFACE When the remote control switch is set to REMOTE, select the device from which to remote-control this unit. 9PIN: Device connected to the REMOTE connector. i.LNK (i.LINK): Device connected to the S400 (i.LINK) connector. 215 i.LINK MODE Select the connection method for the S400 (i.LINK) connector. AV/C: Connect with AV/C. FAM (FAM (PC REMOTE)): Connect with FAM. 216 PARALLEL RECORDING MODE Specifies whether recording of video and audio on this unit should start and stop at the same time as recording on a camcorder connected to this unit by i.LINK(AV/C). off: Do not conduct parallel recording. on: Conduct parallel recording. 257 NETWORK ENABLE Select the remote control switch positions which enable network connections. net (network): Only when the switch is set to “NETWORK.” n&9P (network & remote(9PIN)): When the switch is set to “NETWORK,” and when the switch is set to “REMOTE” and extended menu item 214 is set to “9PIN.” a) a) FTP connections can be made only when the device connected to the REMOTE connector (D-sub 9 pin) is in stop mode. During FTP connections, the device connected to the REMOTE connector cannot be used to control this unit. 98 7-3 Extended Menu Menu items in the 200s, relating to the remote control interface Item number Item name Settings 258 Enable or disable the live logging function when using the PDZ-1 Proxy Browsing Software. off: Disable. on: Enable. LIVE LOGGING Note During live logging, regardless of the settings of the switches (INT/EXT/ RP188, PRESET/REGEN, and F-RUN/R-RUN) in the time data settings section, the internal time code generator always runs in free run mode. Time code cannot be recorded in internal preset mode. Menu items in the 300s, relating to editing operations Item number Item name Settings 308 Select the STD or NON-STD mode in accordance with a composite video or S-video input. STD (forced STD): The STD mode is always used (forced STD mode). N-STD (forced non-STD): Use this setting when the input video signal is unstable (forced NON-STD mode). SELECTION OF STD/NON-STD FOR COMPOSITE VIDEO IN Note When using a VCR with no built-in time base corrector (e.g. a home-use VHS-system VCR), select N-STD. REC INHIBIT Select whether recording is inhibited. off: Do not inhibit recording. on: Inhibit recording. 320 DIGITAL AUDIO PB PROCESS ON EDIT POINT Select the treatment of audio playback at edit points. cut: Carry out a cut (possibly resulting in audio discontinuities at the edit point). fade: Fade out and fade in. 335 OUTPUT REFERENCE SEL Select the reference signal of this unit. ref (ref. video): Use the signal input to the REF VIDEO IN connector as the reference signal. auto: According to the operation mode, automatically select either the signal input to the REF VIDEO IN connector or the input video signal selected with the VIDEO INPUT SEL button as the reference signal. Chapter 7 Menus 310 For more details, see the following item “External synchronization to reference signal generators” (page 100). The input digital audio signals and video signals must be synchronized with the reference signal input to the REF VIDEO IN connector. 7-3 Extended Menu 99 External synchronization to reference signal generators The internal reference signal generator is synchronized either to a reference signal input to the REF VIDEO IN connector or an input video signal. Depending on the settings of extended menu items 335 and 308, and the input signal selection, the external synchronization status is as shown in the following table. The video signals are output always synchronized to the internal reference signal. VIDEO INPUT SEL button setting COMPOSITE Item 335 setting ref Item 308 setting STD Operation mode External synchronization status When a signal is input E-E mode to the REF VIDEO IN Normal playback connector REF a) auto N-STD REF a) STD N-STD REF a) REF a) REC button pressed Recording When no signal is input to the REF VIDEO IN connector INPUT/Free b) INPUT/Free b) E-E mode Free RUN d) Free RUN d) Normal playback REC button pressed Recording Chapter 7 Menus VIDEO INPUT SEL button setting SDI Item 335 setting ref Item 308 setting STD/N-STD Operation mode External synchronization status When a signal is input E-E mode to the REF VIDEO IN Normal playback connector REC button pressed REF a) SG auto ref/auto ref/auto STD/N-STD STD/N-STD STD/N-STD REF a) REF a) Free RUN d) Free RUN d) REF a) Recording When no signal is input to the REF VIDEO IN connector i.LINK SDI IN/Free c) SDI IN/Free c) E-E mode Normal playback REC button pressed Recording a) Synchronize to the reference signal input to the REF VIDEO IN connector. b) Synchronize to the signal input to the VIDEO IN connector. If no signal is input to the connector, no synchronization is made. c) Synchronize to the signal input to the SDI IN connector. If no signal is input to the connector, no synchronization is made. d) No external synchronization is made. Menu items in the 400s, relating to preroll Item number Item name 401 100 Settings FUNCTION MODE AFTER CUE-UP Select the state that the unit goes into after a cuing-up operation. stop: Stops (the stop mode). still: Still playback (in jog and shuttle mode). 7-3 Extended Menu Menu items in the 500s, relating to disc protection Item number Item name Settings 501 To protect the disc against shock and vibrations, and to lengthen the life of the laser diodes, the unit automatically enters standby off mode whenever a specified time elapses in a disc stop mode (stop mode or the still picture mode of search mode). This allows you to set the time after which the unit exits a disc stop mode and enters standby off mode. 0.5 s (0.5 sec)... 8 m (8 min)... 30 m (30 min): Can be set in the range from 0.5 seconds to 30 minutes. off: Do not put into standby off mode. STILL TIMER Menu items in the 600s, relating to the time code, metadata, and UMID Item number Item name Settings 601 Select a line into which to insert VITC signals for IMX recording signals a) and DVCAM playback signals. b) 12 H (12 line)... 16 H (16 line)... 20 H (20 line) (in 525(U)/525(J) line modes) 9 H (9 line)... 19 H (19 line)... 22 H (22 line) (in 625 line mode) VITC POSITION SEL-1 Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. a) In the IMX format, VITC is inserted as video signals in vertical blanking sections. Because these signals are output as video signals during playback, the insertion line can be specified only for recording. b) In the DVCAM format, VITC is recorded as VAUX (Video Auxiliary) data. Because VITC is inserted into video signals by the VITC generator only during playback, the insertion line can be specified only for playback. 602 VITC POSITION SEL-2 Chapter 7 Menus Select a line into which to insert VITC signals for IMX recording signals a) and DVCAM playback signals. b) 12 H (12 line)... 18 H (18 line)... 20 H (20 line) (in 525(U)/525(J) line modes) 9 H (9 line)... 21 H (21 line)... 22 H (22 line) (in 625 line mode) Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. a) In the IMX format, VITC is inserted as video signals in vertical blanking sections. Because these signals are output as video signals during playback, the insertion line can be specified only for recording. b) In the DVCAM format, VITC is recorded as VAUX (Video Auxiliary) data. Because VITC is inserted into video signals by the VITC generator only during playback, the insertion line can be specified only for playback. 605 TCG REGEN MODE Select the signal to be regenerated when the time code generator is in the regeneration mode (i.e., when the PRESET/REGEN switch is set to REGEN). TC&UB: Both the time code and user bits are regenerated. TC: Only the time code is regenerated. UB: Only the user bits are regenerated. 607 U-BIT BINARY GROUP FLAG Select the user bits to be used in the time code generated by the time code generator. 000 (000:not specified): Character set not specified. 001 (001:iso character): 8-bit characters compliant with ISO 646 and ISO 2022. 010 (010:unassigned-1): Undefined. 011 (011:unassigned-2): Undefined. 100 (100:unassigned-3): Undefined. 101 (101:page / line): SMPTE 262M page/line multiplex system. 110 (110:unassigned-4): Undefined. 111 (111:unassigned-5): Undefined. 7-3 Extended Menu 101 Menu items in the 600s, relating to the time code, metadata, and UMID Item number Item name Settings 611 TC OUTPUT PHASE IN EE MODE Select the time code output mode for output from the TC OUT connector in E-E mode. mutng (muting): Suppress the output. thru (through): Output the time code input to the TC IN connector as it is. v-in (video input phase): Output the time code with the same phase as the input video signal phase. v-out (video output phase): Output the time code with the same phase as the output video signal phase. 612 TC OUTPUT MUTING IN SEARCH MODE Select whether to suppress the output from the TC OUT connector in jog/ shuttle mode. on: Suppress. off: Do not suppress. 619 VITC Specify whether or not to record the VITC generated by the internal time code generator. off: Do not record internally generated VITC. on: Record internally generated VITC. Note Even if this item is set to “off,” VITC is recorded if the input video signal contains VITC and the VITC line is set to “thru” with item 723. 628 DF MODE In 525(U)/525(J) line modes, when the INT/EXT/RP188 switch is set to INT and the PRESET/REGEN switch is set to PRESET, select the frame mode of the internal time code generator and counter. df (on (df)): Drop-frame mode ndf (off (ndf)): Non-drop frame mode 629 TC SELECT Select the type of time data to show in the time data display, and the type of external time code when the INT/EXT/RP188 switch is set to EXT and the PRESET/REGEN switch is set to REGEN. vitc: Display time code as VITC, or select VITC as the external time code. tc: Display time code as TC, or select TC as the external time code. Chapter 7 Menus See 4-1-2 “Recording Time Code and User Bit Values” (page 44) for more information about selecting external time code. 632 TC UBIT SELECT When item 629 is set to “tc,” specify whether to synchronize the user bits of the time code generator to the internal clock. fix: Do not synchronize user bits. time: Synchronize user bits to the internal clock. 633 VITC UBIT SELECT When item 629 is set to “vitc,” specify whether to synchronize the user bits of the time code generator to the internal clock. fix: Do not synchronize user bits. time: Synchronize user bits to the internal clock. 634 WATCH AUTO ADJUST When external time code input contains real-time clock user bits, specify whether to adjust the internal clock to match the real-time clock. off: Do not adjust the internal clock to match the real-time clock. on: Adjust the internal clock to match the real-time clock. 651 UMID SDI OUTPUT Select whether to output UMID in the VANC of the SDI output. off: Do not output. on: Output. See 7-3-3 “Using UMID Data” (page 109) for more information about UMID. 102 7-3 Extended Menu Menu items in the 600s, relating to the time code, metadata, and UMID Item number Item name Settings 652 Select the line in which UMID is output when menu item 651 is set to “on.” 12 H (12 line), 13 H (13 line), 15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line), 19 H (19 line) (525(U)/525(J) line modes) 9 H (9 line), 10 H (10 line), 12 H (12 line), 13 H (13 line), 14 H (14 line), 15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line) (625 line mode) UMID SDI VANC LINE See 7-3-3 “Using UMID Data” (page 109) for more information about UMID. 657 ESSENCE MARK SDI OUTPUT Select whether to output essence marks in the SDI output VANC. off: Do not output. on: Output. 660 ESSENCE MARK SDI VANC LINE When item 657 is set to “on,” select the line to which to output essence marks. 12 H (12 line), 13 H (13 line), 15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line), 19 H (19 line) (525(U)/525(J) line modes) 9 H (9 line), 10 H (10 line), 12 H (12 line), 13 H (13 line), 14 H (14 line), 15 H (15 line), 16 H (16 line), 17 H (17 line), 18 H (18 line) (625 line mode) Menu items in the 700s, relating to video control Item name Settings 701 SELECTION OF VIDEO/SYNC DELAY An E-E video signal is output delayed with respect to the video input signal by the time for video circuit processing. With this item, select whether or not to delay the sync signal attached to the output video signal by an amount corresponding to the video signal delay. sync (sync delay): Delay the sync signal by the corresponding amount before attaching it. video (video delay): Attach a sync signal with the same timing as the input signal. 7-3 Extended Menu Chapter 7 Menus Item number 103 Menu items in the 700s, relating to video control Item number Item name Settings 703 BLANK LINE SELECT Switch blanking of the video output signal on or off for individual lines in the vertical blanking interval. The Y/C signal and odd/even fields are blanked simultaneously. Sub-item 1 ALL LINE 2 ... 9 LINE 12 ... LINE 19 10 LINE 20 2 ... 10 LINE 12 ... LINE 20 11 LINE 21 2 ... 15 LINE 9, 322 ... LINE 22, 335 16 LINE 23 - - -: Specify the blanking for each line separately. blnk (blank): Regardless of the setting of other sub-items, blank all lines which can be specified in this menu item. thru (throu): Regardless of the setting of other sub-items, switch off blanking for all lines which can be specified in this menu item. In 525(U) line Specify blanking for lines 12 to 19. mode blnk (blank): Carry out blanking. thru (throu): Switch off blanking. Specify blanking for line 20. blnk (blank): Carry out blanking. half: Carry out half-blanking. thru (throu): Switch off blanking. In 525(J) line mode Specify blanking for lines 12 to 20. blnk (blank): Carry out blanking. thru (throu): Switch off blanking. Specify blanking for line 21. blnk (blank): Carry out blanking. half: Carry out half-blanking. thru (throu): Switch off blanking. In 625 line mode Specify blanking for lines 9, 322 to 22, 335. blnk (blank): Carry out blanking. thru (throu): Switch off blanking. Specify blanking for line 23. half: Carry out half-blanking. thru (throu): Switch off blanking. Chapter 7 Menus 705 EDGE SUBCARRIER REDUCER MODE Select whether to enable the edge subcarrier reducer (ESR). on: Enable. off: Do not enable. When playing back a composite signal, set this to “on.” 707 FORCED VERTICAL INTERPOLATION OFF The “Y-add” function is normally switched on automatically during jog or variable speed playback. This item selects whether or not to force the “Y-add” function off. auto: Automatically switch the “Y-add” function on. off (forced YADD off): Force the “Y-add” function off. The “Y-add” function is off while a disc image is displayed in stop mode (menu item 108 “AUTO EE SELECT” is “off”). The “Y-add” function is a circuit operation to interpolate the video signal vertically during jog or variable speed playback for the purpose of reducing the vertical movement of the playback picture. 710 104 INTERNAL VIDEO SIGNAL GENERATOR 7-3 Extended Menu Select the test signal to be output from the internal test signal generator. When “SG” is selected using the VIDEO INPUT SEL button, the internal test signal generator operates to output the selected test signal. This signal can also be recorded. BB (Black Burst): Black burst signal CB75 (75% Color Bars): 75% color bar signal CB100 (100% Color Bars): 100% color bar signal The factory default settings for each line mode are as follows: In 525(U)/525(J) line modes: CB75 (75% Color Bars) In 625 line mode: CB100 (100% Color Bars) Menu items in the 700s, relating to video control Item number Item name Settings 713 VIDEO SETUP REFERENCE Select whether to remove the setup (7.5%) from the input analog video signals and whether to add the setup (7.5%) to the output analog video signals (when 525(U) or 525(J) line mode is selected). Sub-item 723 1 INPUT LEVEL Whether to remove the setup (7.5%) from the input analog video signals. 0.0%: Do not remove. 7.5%: Remove. The factory default settings for each line mode are as follows: 525(U) line mode: 7.5% 525(J) line mode: 0.0% 2 OUTPUT LEVEL Whether to add the setup (7.5%) to the output analog video signals. 0.0%: Do not add. 7.5%: Add. The factory default settings for each line mode are as follows: 525(U) line mode: 7.5% 525(J) line mode: 0.0% INPUT VIDEO BLANK Sub-item Switch blanking on or off for individual lines in the vertical blanking interval of an input video signal. The Y/C signal and odd/even fields are blanked simultaneously. A signal with blanking carried out according to this setting is recorded. 1 ALL LINE - - -: Specify the blanking for each line separately. blnk (blank): Regardless of the setting of other sub-items, blank all lines which can be specified in this menu item. thru (throu): Regardless of the setting of other sub-items, switch off blanking for all lines which can be specified in this menu item. 2 ... 10 LINE 12 ... LINE 20 In 525(U)/ 525(J) line modes Specify blanking for lines 12 to 20. blnk (blank): Carry out blanking. thru (throu): Switch off blanking. 2 ... 15 LINE 9, 322 ... LINE 22, 335 In 625 line mode Specify blanking for lines 9, 322 to 22, 335. blnk (blank): Carry out blanking. thru (throu): Switch off blanking. H BLANKING WIDTH Select the horizontal blanking width of the output analog video signal. narow (narrow): Digital blanking (narrow) wide: Analog blanking (wide) When “wide” is selected, the horizontal blanking width complies with RS170A, and normally the blanking is widened and the image becomes narrower. It is recommended to select “narow” at the editing stage, then later, for broadcast transmission to select “wide,” to output a signal conforming to the standard. Note, however, that “narow” has to be always selected for SDI signals. 728 OUTPUT SCH PHASE Set the subcarrier H phase. –512 (–512 (DEC))... 0 (0 (DEC))... 511 (511 (DEC)) 7-3 Extended Menu Chapter 7 Menus 726 105 Menu items in the 700s, relating to video control Item number Item name Settings 731 WIDE MODE Specify whether to record and play back with the addition of wide picture information. Sub-item 1 INPUT Specify whether to save wide picture information on a disc during recording. auto: Automatically record wide picture information when it is detected in the selected input video signal. on: Always record wide picture information. off: Do not record wide picture information. 2 OUTPUT Specify whether to add wide picture information to the output signal during MPEG IMX playback. thru (through): Output the video signals of the disc being played back without adding wide picture information. auto: When wide picture information is detected on the disc being played back, add wide picture information to the output video signals. Notes • To add wide picture information to the output signal, it is necessary, in addition to setting this item to “thru,” to operate extended menu item 703 to set line 20 (in 525 line mode) to “thru” or set line 23 (in 625 line mode) to “thru.” • In 525 line mode, wide picture information may not be output if VITC signal insertion position is set to line 20 in extended menu item 601 or 602. Menu items in the 800s, relating to audio control Chapter 7 Menus 106 Item number Item name Settings 802 DIGITAL AUDIO MUTING IN SHUTTLE MODE Set the audio muting conditions during shuttle playback. off: Not muted. on: Muted. 807 AUDIO OUTPUT PHASE Set the output timing of digital audio playback signals (SDI, AES/EBU only), with 80H as a reference position. Output timing is earlier for values smaller than 80H and later for values greater than 80H. (80H, 128 samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs) 0 (0 (HEX))... 80 (80 (HEX))... FF (FF (HEX)): Values can be set in this range. 808 INTERNAL AUDIO SIGNAL GENERATOR Select the operation of the internal audio test signal generator. silnc (silence): Silent signal. 1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal. When you select SG as the audio input in the input selection section of the control panel, the audio test signal generated by the internal audio test signal generator is input. 815 AUDIO SAMPLING RATE CONVERTER Select the mode of operation of the sampling rate converter for AES/ EBU input to channels 1 to 4. off: Do not operate. on: Operate. 820 AUDIO OUTPUT CH1/CH2 SELECT Select the signals to be output from the AUDIO OUT 1/3 and AUDIO OUT 2/4 connectors. line (line out): Output the audio channel signals selected with item 824 “just as they are” from the AUDIO OUT 1/3 and 2/4 connectors. moni (monitor out): Output the monitor audio L-channel (CH-1) and monitor audio R-channel (CH-2) signals from the AUDIO OUT 1/3 and AUDIO OUT 2/4 connectors, respectively. 7-3 Extended Menu Menu items in the 800s, relating to audio control Item number Item name Settings 823 Control non-audio flags in digital audio output. NON-AUDIO FLAG PB Sub-item 824 1 CH1/CH2 2 CH3/CH4 3 CH5/CH6 4 CH7/CH8 ANALOG LINE OUTPUT SELECT During playback (except E-E mode), set non-audio flags in digital audio output to the following states. on: Set to on (data is non-audio) auto: Set as follows. • When data is read from disc and confirmed: Follow the data. • When data from disc is not confirmed: Maintain current state. Select the analog audio signals (tracks 1 to 8) to be assigned to audio output channels 1 and 2. tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2. tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2. tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2. tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2. Note When item 820 is set to “moni,” the left channel (CH-1) and right channel (CH-2) of monitor audio are output from the AUDIO OUT 1/3 and 2/4 connectors respectively, regardless of the setting of this item. 827 AES/EBU AUDIO OUTPUT SELECT Select the audio signals to assign to AES/EBU audio output channels. Sub-item 828 1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2. tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2. tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2. tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2. 2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4. tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4. tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4. tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4. SDI/DV AUDIO OUTPUT SELECT Sub-item Select the audio signals to assign to SDI and i.LINK(AV/C) audio output channels. 1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2. tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2. tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2. tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2. 2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4. tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4. tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4. tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4. 831 DV OUT AUDIO MODE Select the audio mode for 4ch: 12 bit/32 kHz/4ch 2ch: 16 bit/48 kHz/2ch 837 AUDIO MONITOR CHANNEL ARRANGE Together with item 838, select the audio signals (tracks 1 to 4) to assign to the left and right channels of the audio monitor. Chapter 7 Menus s S400 (i.LINK) connector (output). Sub-item L-1 Lch/tr1 L-2 Lch/tr2 L-3 Lch/tr3 L-4 Lch/tr4 No display: Do not assign. on: Assign. The factory default settings are as follows. Lch: tr1 Rch: tr2 R-1 Rch/tr1 R-2 Rch/tr2 R-3 Rch/tr3 R-4 Rch/tr4 7-3 Extended Menu 107 Menu items in the 800s, relating to audio control Item number Item name Settings 838 Together with item 837, select the audio signals (tracks 5 to 8) to assign to the left and right channels of the audio monitor. AUDIO MONITOR CHANNEL ARRANGE Sub-item L-5 Lch/tr5 L-6 Lch/tr6 L-7 Lch/tr7 L-8 Lch/tr8 No display: Do not assign. on: Assign. The factory default settings are as follows. Lch: No display Rch: No display R-5 Rch/tr5 R-6 Rch/tr6 R-7 Rch/tr7 R-8 Rch/tr8 Menu items in the 900s, relating to digital process Item number Item name Settings 920 Select whether or not to add information to the SDI output. SD-SDI H-ANC CONTROL Sub-item 1 AUDIO 5CH-8CH off: Do not add digital audio data channels 5 to 8. on: Add digital audio data channels 5 to 8. 2 RP188 ATC off: Do not add RP188 time code data. on: Add RP188 time code data. 7-3-2 Extended Menu Operations Chapter 7 Menus The extended menu can be used with the same procedures as in the basic menu. However, since with the factory default settings the extended menu is not displayed, it is first necessary to enable display of the extended menu. See “Basic setup menu operations” (page 94) for more information about how to select menu items and how to change their values. Enabling display of the extended menu To enable display of the extended menu, an internal switch must be set to on, and extended menu display must be enabled in the maintenance menu. (The internal switch is set to on when the unit is shipped from the factory. Unless you have set it to off, there is no need to change the switch setting.) To set the internal switch to on 1 108 Using a Phillips screwdriver, remove the cover on the rear panel of this unit 7-3 Extended Menu 2 Use a ballpoint pen or other sharp implement to set the leftmost of the DIP switches on the right side to the ON (top) position. Note Do not use a pencil for this operation, as graphite deposits can cause short circuits and lead to failure. MAINTENANCE MENU DRIVE MAINTENANCE ADJUST CHECK BATTERY CONFIG AUDIO CONFIG NETWORK CONFIG SETUP MAINTENANCE SERVICE SUPPORT OTHERS 1234 1234 1234 1234 Set this switch to “ON.” 3 4 Press the g button. 5 Use the F/f buttons to select “EXTENDED MENU.” MAINTENANCE MENU SETUP MAINTENANCE T EXTENDED MENU : dis t SETUP BANK4 SAVE MENU DATA LOAD MENU DATA AU BANK RECALL: off RESET ALL SETUP Replace the cover. Note Tighten the screws firmly. To enable extended menu display in the maintenance menu The menu screens in the following procedure are those that appear in the video panel, and on a monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. Proceed as follows. 1 ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN REGEN R-RUN COUNTER SEL RP188 CH-2 PLAY F REV 7 Press the f button to select “ENABLE.” MAINTENANCE MENU SETUP MAINTENANCE EXTENDED MENU : dis * DISABLE T ENABLE 8 SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE JOG SHIFT CH-3 CH-4 METER SEL MONITOR SEL L/ST/R NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC OUT IN TOP Press the g button. EXT AUDIO PREV HOLD 6 Chapter 7 Menus TC KEY INHI ON NETWORK LOCAL REMOTE OFF ACCESS 2 t F FWD END MARK2 8 3,5,7 1 4,6 Hold down the COUNTER SEL button, and press the SET button. The screen switches to the maintenance menu. 3 When you next display the menu and change the item display, the extended menu will appear after the basic menu. Press the MENU button. The setup menu appears in the video panel and on the external monitor. 2 Press the SET button. Use the F/f buttons to select “SETUP MAINTENANCE.” 7-3-3 Using UMID Data To perform operations from interviewing to editing effectively and to detect audio-visual materials easily when reusing them, metadata that provides additional information is recorded along with audio-visual data. As one of application of metadata, the UMID (Unique Material Identifier) is internationally standardized. 7-3 Extended Menu 109 What is a UMID? The UMID (Unique Material Identifier) is a unique identifier for audio-visual material defined by the SMPTE330M-2003 standard. The UMID may be used either as the 32-byte Basic UMID or as the Extended UMID, which includes an additional 32 bytes of Source Pack to make a total 64 bytes. For details, refer to SMPTE 330M. Extended UMID (64 bytes) Basic UMID (32 bytes) Source Pack (32 bytes) Universal label L Inst. No. Material Number Time/Date Spatial Co-ordinates 12 bytes 1 3 bytes 16 bytes 8 bytes 12 bytes Globally unique ID is automatically recorded in clip units. The Extended UMID is metadata that provides additional information such as location, time/date, company and so on. Instance No. Country Org User 4 bytes 4 bytes 4 bytes The UMID is applied as follows. Material No. ID generated when recording Same as the above Source Pack Shooting information (when, where and who) Same as the above M Material source ID/detecting material M Metadata pack that identifies the source of material unit by defining the when, where and who of the material unit with which it is associated. Chapter 7 Menus Original material: 00 00 00 Copied material: generation number (1 byte) + random number (2 bytes) M Distinguishing between the original material and copied material Using the Extended UMID You have to enter a country code, organization code and user code. Set the country code referring to the ISO-3166 table, and set the organization code and user code independently. For details, see “About UMID ownership information” (page 111). Functions of UMID data The UMID data enables the followings: • Add a globally unique ID to every clip of audio-visual material. The unique ID is used to detect the material source and to link it with the original source material. • Distinguishing between original material and copied material. 00 is added to the Instance Number for original material. 110 7-3 Extended Menu • Recording based on the UTC. The UTC is used when recording the UMID. This enables uniform control of source material recorded all over the world based on the universal time code. • Calculating the date difference among source materials. The source material is recorded based on the MJD (Modified Julian Date), which enables easy calculation of date difference among source materials. Setting UMID ownership information Proceed as follows. 1 Set extended menu item 029 “STORED OWNERSHIP” to “on.” See 7-2-2 “Basic Menu Operations” (page 94) for more information about how to make this setting. 2 Set the following item. Item Contents COUNTRY Country code ORGANIZATION Organization code USER User code To change the currently selected item Hold down the STOP button, and turn the jog dial or shuttle dial. To select a different digit to be changed Turn the jog dial or shuttle dial. • There are no problems in recording or playing back audio-video signals, if ORGANIZATION is not set. USER (user code) Enter the 4-byte alphanumeric strings for user identification. The user code is registered with each organization locally. It is usually not centrally registered. When the country code is less than 4 bytes, enter the country code from the beginning of the 4 bytes and enter the space character (20h) in the remaining strings. This user code is determined by the organization. The methods used depend on the organization. Note To change the value of a digit Hold down the SHUTTLE button, and turn the jog dial or shuttle dial. 3 User code cannot be entered when no organization code has been entered. Press the SET button. About UMID ownership information COUNTRY (country code) Enter an abbreviated alphanumeric string (4-byte alphanumeric strings) according to the values defined in ISO 3166-1. There are about 240 country codes. Find your own country code on the following home page. Chapter 7 Menus Refer to ISO-3166-1: http://www.evertype.com/standards/iso3166/iso3166-1en.html When the country code is less than 4 bytes, the active part of the code will occupy the first part of the 4-bytes and the remainder must be filled with the space character (20h). Example: In the case of Japan For Japan, if the country code is JP, it is 2 bytes, if JPN, it is 3 bytes. Thus, enter the following: JP_ _ or JPN _ where _ represents a space. ORGANIZATION (organization code) Enter an abbreviated 4-byte alphanumeric string for the organization code. Notes • Organization codes must be acquired by applying to the SMPTE registration office. When no organization code has been acquired, it is forbidden to enter an arbitrary string. As a rule, the code “00” must be entered. Freelance operators who do not belong to an origination should enter “~.” 7-3 Extended Menu 111 7-4 Maintenance Menu 7-4-1 Items in the Maintenance Menu The following tables show the items in the maintenance menu. • Item names are the names which appear in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. • The values in the Settings columns are the values which appear in the time data display section. (The values may appear in a different format in the video panel and on an external monitor. In this case, the video panel values are shown in parentheses.) Underlined values are the factory defaults. For information about the DRIVE MAINTENANCE, ADJUST, CHECK, BATTERY CONFIG and SERVICE SUPPORT items, refer to the Maintenance Manual. AUDIO CONFIG: items relating to audio control Item Setting METR HEAD ROOM Select the audio reference level (headroom). –12dB,–16dB, –18dB, –20dB (525(U)/525(J) line modes) –12dB, –16dB, –18dB, –20dB, EBUL (625 line mode) DATA LENGTH When “IMX50,” “IMX40,” or “IMX30” is selected in setup menu item 031, this selects the audio quantization bit count and number of recording channels. 16×8 (16bit × 8ch): 16 bits × 8 channels 24×4 (24bit × 4ch): 24 bits × 4 channels Note When item 031 is set to “DVCAM,” the setting is automatically fixed at 16 bits × 4 channels. NON-AUDIO INPUT Sub-item Select whether to handle digital audio signals as non-audio signals during recording. Audio (audio): Handle as audio signals. data: Handle as non-audio signals. Chapter 7 Menus tr1/tr2 tr3/tr4 tr5/tr6 tr7/tr8 INPUT LEVEL Sub-item Set the upper limit for the signal level input to audio channels 1/3 or 2/4. +4dB, 0dB, –3dB, –6dB (525(U)/525(J) line modes) +4dB, 0dB, –3dB, –6dB, EBUL (625 line mode) CH1/CH3 CH2/CH4 OUTPUT LEVEL Set the reference level for audio output signals. +4dB, 0dB, –3dB, –6dB (525(U)/525(J) line modes) +4dB, 0dB, –3dB, –6dB, EBUL (625 line mode) NETWORK CONFIG: items relating to network settings Item Setting DHCP Set whether to assign an IP address automatically with the DHCP server. DISABLE: Do not assign automatically. ENABLE: Assign automatically. IP ADDRESS PRESET Set IP address. 192.168.001.010 Note When DHCP is set to “ENABLE,” it is not possible to set the IP address. 112 7-4 Maintenance Menu NETWORK CONFIG: items relating to network settings Item Setting SUBNET MASK PRESET Set the subnet mask. 255.255.255.000 Note When DHCP is set to “ENABLE,” it is not possible to set the subnet mask. DEFAULT GATEWAY PRESET Set the default gateway. 000.000.000.000 Note When DHCP is set to “ENABLE,” it is not possible to set the default gateway. LINK SPEED Set the communications speed. AUTO, 10Mbps, 100Mbps DUPLEX Set the communications method. AUTO, Full (Full Duplex), Half (Half Duplex) For details of how to make settings, see “To change network settings” (page 115). SETUP MAINTENANCE: items relating to the setup menu Setting EXTENDED MENU Select whether or not to display the extended menu. DISABLE: Do not display. ENABLE: Display. SETUP BANK4 Select the bank to be stored in menu bank 4, or reset menu bank 4. Cur to 4 (CURRENT TO BANK4): Store the current menu settings in menu bank 4. 1 to 4 (BANK1 TO BANK4): Store the menu bank 1 settings in menu bank 4. 2 to 4 (BANK2 TO BANK4): Store the menu bank 2 settings in menu bank 4. 3 to 4 (BANK3 TO BANK4): Store the menu bank 3 settings in menu bank 4. Reset (RESET BANK4): Reset menu bank 4. SAVE MENU DATA Select whether to temporarily back up (save) setup menu settings before operations such as software upgrades. SET button: Back up (save) the settings. MENU button: Return to next highest menu level without backing up. LOAD MENU DATA Select whether to restore (load) setting that were backed up (saved) with the “SAVE MENU DATA” item. SET button: Restore (load) the settings. MENU button: Return to the next highest menu level without restoring. AU BANK RECALL Select whether to recall settings automatically from a menu bank when the system is powered on, and if so which menu bank to recall from. off: Do not recall settings from a menu bank. Bank1 (from BANK1): Recall settings from menu bank 1. Bank2 (from BANK2): Recall settings from menu bank 2. Bank3 (from BANK3): Recall settings from menu bank 3. Bank4 (from BANK4): Recall settings from menu bank 4. RESET ALL SETUP Reset the current menu settings to the factory settings. SET button: Reset. MENU button: Return to the next highest menu level without resetting. Chapter 7 Menus Item Notes • The line mode setting is also cleared. If you execute this item, reset the line mode (see page 7). • Date and time settings are not cleared, but the time zone setting is cleared. After executing this item, reset the time zone (see page 34). 7-4 Maintenance Menu 113 OTHERS Item Setting SDI SUPER Select whether to output superimpose characters to the SDI OUT (SUPER) connector. ON: Output. OFF: Do not output. For details about OTHERS items other than the above, refer to the Maintenance Manual. highlighted, and the arrow (c) flashes to indicate that you can move to a lower-level menu. 7-4-2 Maintenance Menu Operations Group selection screen Basic maintenance menu operations The following explains how to select maintenance menu items and how to change their values. The menu screen shown are those that appear in the video panel and on a monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. First change the switch setting within the unit, then carry out the following operations. MAINTENANCE MENU DRIVE MAINTENANCE ADJUST CHECK BATTERY CONFIG AUDIO CONFIG NETWORK CONFIG SETUP MAINTENANCE SERVICE SUPPORT OTHERS For information about how to change the switch setting within the unit, see page 108. t Flashing Video panel To select the item group Use the F/f buttons. 3 DATA dB OVER 0 DATA DATA dB OVER 0 dB OVER 0 Chapter 7 Menus -12 -12 -12 -12 -20 -20 -20 -20 -30 -40 -30 -40 -30 -40 -30 -40 -60 -60 -60 -60 CH- 15 CH- 26 CH- 37 AUDIO INPUT CH INPUT SEL VITC VITC VIUB COUNTER HOLD PB NDF EXT-LK CH- 48 VIDEO INPUT SEL KEY INHI WARNING HOURS MINUTES DISC E B BATT E SECONDS F PROCESS CONTROL STATUS CHARACTER REC INHI OFF ON LIGHT OFF ON MONITOR OFF L H ALL/CH-1 VARIABLE REC PRESET PB 2 TC KEY INHI ON NETWORK LOCAL REMOTE OFF INT PRESET F-RUN REGEN R-RUN COUNTER SEL RP188 CH-2 PLAY HOLD 6 SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK MENU SET SHUTTLE F REV JOG SHIFT CH-3 CH-4 METER SEL MONITOR SEL L/ST/R NEXT STOP SYSTEM MENU S.SEL MARK1 REC OUT F FWD END MARK2 2,3,5 1 3,4 Hold down the COUNTER SEL button, and press the SET button. The group selection screen of the maintenance menu appears. The currently selected item group is 114 MAINTENANCE MENU NETWORK CONFIG T DHCP : dis t IP ADDRESS SUBNET MASK DEFAULT GATEWAY LINK SPEED : auto DUPLEX : auto Press the MENU button. The menu appears in the video panel and on the external monitor. 2 Flashing RESET IN TOP Item selection screen EXT AUDIO PREV A lower-level menu (item selection screen) appears. The currently selected item is highlighted, and the arrow (C/c) flashes to indication that you can move to a higher- or lower-level menu. FRAMES 1 ACCESS Press the g button. DATA dB OVER 0 7-4 Maintenance Menu To return to the item group Press the G button. To select the menu item Use the F/f buttons. 4 Press the g button. A lower-level menu (setting modification screen) appears. The current setting is highlighted, and the arrow (C) flashes to indicate that you can move to a higher-level menu. If the current setting is the factory default, a colon (:) appears between the item name and the setting. A midpoint (•) appears if you change the factory default setting to another value and then display the setting modification screen again. For details of the settings, consult your network administrator. When the IP address is assigned automatically Check that the network cable is connected to this unit before carrying out the operation. 4 Setting modification screen TC KEY INHI ON NETWORK LOCAL REMOTE OFF ACCESS ALL/CH-1 PRESET F-RUN REGEN R-RUN COUNTER SEL HOLD RP188 CH-3 CH-4 METER SEL MONITOR SEL L/ST/R AUDIO PREV SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE PLAY NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC IN TOP MAINTENANCE MENU NETWORK CONFIG DHCP : dis T * DISABLE ENABLE Current setting Indicates that the current setting is the factory default (change to “•” if the default setting is changed) Indicates a factory default setting F FWD OUT END MARK2 1,3 2 1 Using the F/f buttons to select “DHCP.” 2 Press the g button. 3 Press the f button to select “ENABLE.” 4 Press the SET button. To check the assigned IP address In the NETWORK CONFIG menu, using the F/f buttons to select “IP ADDRESS,” then press the g button. Chapter 7 Menus To return to the menu item Press the G button. F REV JOG SHIFT EXT CH-2 VARIABLE REC PRESET PB Flashes INT Note When there is a sub-item Repeat steps 3 and 4 until the setting modification screen appears. 5 Using the F/f buttons to select the desired setting. 6 Press the SET button. This saves the new setting, and the menu disappears from the video panel or an external monitor. To cancel changing a setting Before pressing the SET button, press the MENU button. The menu disappears from the video panel or an external monitor, without saving the new setting. If the IP address cannot be assigned, this is shown as “000.000.000.000.” In this case, consult the network administrator. To set the IP address First set DHCP to “DISABLE.” (See the previous item, “When the IP address is assigned automatically.”) 7 4,6 TC KEY INHI ON NETWORK LOCAL REMOTE OFF ACCESS ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN REGEN R-RUN COUNTER SEL RP188 CH-2 PLAY SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE CH-3 CH-4 METER SEL MONITOR SEL L/ST/R NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC OUT IN TOP F REV JOG SHIFT EXT AUDIO PREV HOLD 3 F FWD END MARK2 To change network settings To change network settings, carry out steps 1 to 3 in the procedure of “Basic maintenance menu operations” above, to display the NETWORK CONFIG menu item, then carry out the following operations. 1,3 2,3 7-4 Maintenance Menu 115 1 Using the F/f buttons to select “IP ADDRESS.” 2 Press the g button. The IP ADDRESS PRESET menu appears, and the digit that can be changed flashes. Item selection screen Flashing IP ADDRESS PRESET IP : 192.168.001.010 DHCP: disable SHIFT INC/DEC CLEAR DATA SET TO MENU 3 : (C)(c)KEY : JOG DIAL : RESET KEY : SET KEY : MENU KEY Set the IP address. To select a different digit to be changed Use the G/g buttons. Chapter 7 Menus To change the value of a digit Turn the jog dial or shuttle dial. Turning clockwise increases the value, and turning counterclockwise decreases the value. The F/f buttons can be used. To return to the factory default setting Press the RESET button. 4 When all digits are set, press the SET button. This returns to the NETWORK CONFIG menu. To cancel a setting Before pressing the SET button, press the MENU button. This returns to the NETWORK CONFIG menu, without saving the new setting. 116 5 Repeat steps 1 to 4 as required, to set the subnet mask and default gateway. 6 In the NETWORK CONFIG menu, press the SET button. 7 When the “NOW SAVING...” message vanishes, power the unit off and then on again with the on/ standby switch. 7-4 Maintenance Menu Setting the communications speed Set the communications speed (LINK SPEED) and communications method (DUPLEX) to match the network environment. For details of the operation, see “Basic maintenance menu operations” (page 114). 7-5 System Menu 7-5-1 Items in the System Menu The following tables show the items in the system menu. Item names are the names which appear in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. DISC MENU: items relating to disc Item Setting STATUS Display disc status or clip status. Sub-item Note Although the PDZ-1 Proxy Browsing Software can write TITLE1 and TITLE2, only TITLE1 is displayed here. 1 DISC Display disc status. 2 CLIP Display clip status. DELETE Delete clips on the disc. Sub-item 1 LAST CLIP Delete the last clip. 2 ALL CLIP Delete all the clips. (Locked files and files in the General directory cannot be deleted.) FORMAT Select the disc format, and carry out formatting. Sub-item 1 QUICK FORMAT Quick format (Deletes all data on the disc, including the contents of the General directory.) DATE/TIME PRESET: items relating to date and time setting Setting YEAR Set the year, month, day, time, and time zone. Chapter 7 Menus Item MONTH DAY TIME TIME ZONE 7-5-2 System Menu Operations MENU button SET button SHIFT button RESET button TC KEY INHI NETWORK ON LOCAL REMOTE OFF ACCESS ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN REGEN R-RUN COUNTER SEL RP188 CH-2 CH-3 CH-4 PLAY METER SEL MONITOR SEL L/ST/R AUDIO PREV HOLD SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC IN TOP F REV JOG SHIFT EXT F FWD OUT END MARK2 Arrow buttons 7-5 System Menu 117 To display disc status and clip status To return to the previous menu page Press the MENU button. Insert a disc and proceed as follows. 1 The system menu appears in the video panel or on an external monitor. 2 Press the F button or f button to select “DISC MENU,” then press the g button. The DISC MENU page appears. 3 Press the F button or f button to select “STATUS,” then press the g button. The “STATUS” menu item appears. 4 To exit the menu system Press the MENU button twice. Hold down the SHIFT button and press the MENU button. To delete clips Notes • Clips cannot be deleted when the Write Inhibit tab of the disc is set to the recording disabled position, or when extended menu item 310 “REC INHIBIT” is set to “on.” • Locked clips (see page 55) are not deleted. Proceed as follows. 1 Carry out steps 1 and 2 in the previous section “To display disc status and clip status.” 2 Press the F button or f button to select “DELETE,” then press the g button. Display the disc status or the status of the current clip. To display the disc status Press the F button or f button to select “DISC,” then press the g button. The status of the loaded disc appears. The “DELETE” menu item appears. 3 DISC STATUS USER ID: TITLE : To delete the last clip Press the F button or f button to select “LAST CLIP,” then press the g button. (no ID) (no name) Chapter 7 Menus REMAIN REWRITE SALVAGE FILE SYSTEM The name of the clip to be deleted appears. To cancel the deletion and return to the previous page, press the MENU button. : 029 min : 0002 times : OK : OK To delete all clips Press the F button or f button to select “ALL CLIP,” then press the g button. TO MENU : MENU KEY To display the status of the current clip Press the F button or f button to select “CLIP,” then press the g button. The status of the clip at the current position appears. (When the current clip changes because of playback or a search, the display switches to the status of the new clip.) CLIP STATUS CLIP NO : 001/010 NAME : C0001 TITLE: (no name) RECORD DEVICE: PDW-R1 SERIAL: 10001 DATE : 01/01/06 TIME : 19:54:38 TO MENU : 118 7-5 System Menu MENU KEY Delete the last clip or all clips. The message “ALL DELETE OK?” appears. To cancel the deletion and return to the previous page, press the RESET button. To cancel the deletion and exit the menu system, press the MENU button. 4 Press the SET button. The last clip is deleted, or all clips are deleted. You can use the THUMBNAIL MENU to delete the selected clip or all clips. For details, see page 56. To format discs See 3-6-5 “Formatting a Disc” (page 39). To set the date and time See 3-4 “Setting the Date and Time” (page 34). Chapter 7 Menus 7-5 System Menu 119 Maintenance and Troubleshooting 8-1 Periodic Maintenance 8-1-1 Digital Hours Meter The digital hours meter can provide six items of information about the operational history of the unit. This information appears in the time data display section, in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. Use the information as a guide in scheduling periodic maintenance. Chapter 8 H14: SPINDLE RUNNING mode (resettable) This shows the cumulative spindle rotation time, in units of hours. The count is resettable. This can be used as a guide in determining when to replace the spindle motor. H15: LOADING COUNTER mode (resettable) Display the total number of times disc has been loaded in the unit. The count is resettable. To display the digital hours meter Press the MENU button, then turn the jog dial or shuttle dial to display the required item in the time data display and in the video panel or on an external monitor. For periodic maintenance, consult your Sony dealer. TC KEY INHI NETWORK ON LOCAL REMOTE OFF ACCESS Display modes of the digital hours meter ALL/CH-1 VARIABLE REC PRESET PB INT PRESET F-RUN REGEN R-RUN COUNTER SEL RP188 CH-2 CH-3 CH-4 H11: OPERATION mode (resettable) Same as H01 except that the count is resettable. This can be used as a guide in determining when to replace parts. H12: LASER PARAMETER mode (resettable) This shows a counter of the cumulative light output time by the optical head in units of hours. 1) The count is resettable. This can be used as a guide in determining when to replace the optical head. 1) The counter advances at different rates during recording and playback. It is also affected by the ambient temperature. H13: SEEK RUNNING mode (resettable) This shows the cumulative seek operation time for the optical head in units of hours. The count is resettable. This can be used as a guide in determining when to replace the seek motor. 120 8-1 Periodic Maintenance PREV PLAY METER SEL MONITOR SEL L/ST/R AUDIO H01: OPERATION mode Displays the total number of hours the unit has been powered on in units of 1 hour. HOLD SUB CLIP THUMB NAIL CLIP MENU ESSENCE MARK SHUTTLE NEXT STOP MENU SYSTEM MENU SET RESET S.SEL MARK1 REC OUT IN TOP F REV JOG SHIFT EXT F FWD END MARK2 Shuttle dial Jog dial MENU button To exit from the digital hours meter Press the MENU button. To jump to H01 Press the MENU button, then the COUNTER SEL button. Every time you press the COUNTER SEL button, menu item H01 or B01 is recalled alternately. 8-2 Condensation 8-3 Error Messages When this unit is moved from a cold place to a warmer place, or operated in high humidity, condensation may form on the optical pickup. This is called condensation, and if the unit is operated in this state, it may make correct recording and playback impossible. Note the following points, to avoid problems with condensation. • When moving the unit under conditions in which condensation is likely, first insert the disc, and close the lid on the disc slot. • If when you move the on/standby switch to the ` position the indication “HUMID” appears in the status display, do not insert a disc until the indication disappears. Error codes appear in the time data display when an error (usually a hardware problem) occurs. Error codes and error messages appear in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input. When an error message appears, follow the instructions in the error message to resolve the problem. Display in video panel and on external monitor Error code ERROR AN ERROR HAS BEEN DETECTED. INFORM SERVICE OF FOLLOWING CODE: 50-010 PRESS EJECT KEY TO EJECT DISC. Display in time data display Error code Chapter 8 Maintenance and Troubleshooting 8-2 Condensation / 8-3 Error Messages 121 8-4 Alarms An alarm (warning message) appears in the time data display when an operation is attempted which is inappropriate for the settings on this unit or the state of the disc. The video panel and an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input displays the alarm message and also the action to take to resolve the problem. Display in video panel and on external monitor ALARM REMOTE MODE IS SELECTED. SET REMOTE/LOCAL/NETWORK SWITCH TO LOCAL. Display in time data display 8-4-1 Alarm List Chapter 8 Maintenance and Troubleshooting The following tables list the alarms displayed by this unit, categorized according to the state of the unit when the alarms occur. The setting of basic menu item 016 “ALARM DISPLAY” determines whether or not some of these alarms appear. The “Display condition” column in the tables shows whether the alarm is displayed according to or regardless of the setting of menu item 016. See 7-2-2 “Basic Menu Operations” (page 94) for more information about how to set menu item 016. 122 8-4 Alarms When the unit is powered on Message in time Display data display condition a) Description Action MENU Ver.UP Setup menu settings were reset, because this unit was upgraded. Reset the setup menu items. on, limit, off See 7-2-2 “Basic Menu Operations” (page 94) and 7-3-2 “Extended Menu Operations” (page 108) for information about making setup menu settings. Maintenance menu item “SETUP MAINTENANCE” - “SAVE MENU DATA/ LOAD MENU DATA” (see page 113) can be used to temporarily back up and restore the current menu settings. ILL. SETUP! on, limit, off Setup menu data is invalid, or data recalled with the maintenance menu item “SETUP MAINTENANCE” – “AUTO BANK RECALL” is invalid. Reset the items in the setup menu. Exchg batt! on, limit, off NVRAM battery is exhausted. It is time to exchange the battery on the board. Contact your Sony service representative. LOW BATT! on, limit, off Battery pack power is low. Exchange with a charged battery pack. BATT EMPTY! on, limit, off Battery pack power is exhausted. See 3-2-3 “Using a Battery Pack” (page 33) for more information about exchanging battery packs. a) With respect to setting of basic menu item 016 When a disc is inserted Message in time Display data display condition a) Description Action Unknown FS! The loaded disc was formatted by an unknown file system. Eject or format the disc. Eject the disc. on, limit, off See 3-6-5 “Formatting a Disc” (page 39) for more information about formatting. on, limit, off The file system cannot be detected. ILL. Disc! on, limit, off An unsupported disc was inserted. Salvage NG on, limit, off Recovery of disc contents (salvage) failed. See 3-6-7 “Handling of Discs When Recording Does Not End Normally (Salvage Function)” (page 40). 525/60 Clip on, limit A disc recorded in NTSC format was inserted when this unit is in 625 line mode (PAL system). Use a disc recorded with the PAL system. 625/50 Clip on, limit A disc recorded in PAL format was inserted when this unit is in 525(U) or 525(J) line mode (NTSC system). Use a disc recorded with the NTSC system. IMX50 Clip IMX40 Clip IMX30 Clip DVCAM Clip on, limit The recording format of the loaded disc differs from the format specified with basic menu item 031 “RECORDING FORMAT.” To record on the disc, change the setting of basic menu item 031. Chapter 8 Maintenance and Troubleshooting No FS! See 7-2-2 “Basic Menu Operations” (page 94) about how to change this setting. 8-4 Alarms 123 Message in time Display data display condition a) Description Action 4CHx24 Clip 8CHx16 Clip on, limit The number of channels and quantizing To record on the disc, change the setting of bits of the loaded disc differ from the maintenance menu item “AUDIO CONFIG” specifications of maintenance menu item - “DATA LENGTH.” “AUDIO CONFIG” - “DATA LENGTH.” See 7-4-2 “Maintenance Menu Operations” (page 114) about how to change this setting. No Support! on, limit, off A disc recorded in an unsupported recording format was inserted. Use a disc recorded in the MPEG IMX or DVCAM format. ILL. Index! on, limit, off An index file error was detected. Format the disc. For details, see 3-6-5 “Formatting a Disc” (page 39). FORMAT NG! on, limit, off Automatic format failed. Use another disc. DI read err on, limit, off A disc read error occurred. DRV ADJ err on, limit, off Adjustment processing failed when a disc was inserted. Try ejecting the disc and inserting it again, or insert another disc. a) With respect to setting of basic menu item 016 During playback Chapter 8 Maintenance and Troubleshooting Message in time Display data display condition a) Description Action 525/60 Disc on, limit An attempt was made to play back a disc Use a disc recorded with the PAL system. recorded with the NTSC system when this unit is in 625 line mode (PAL system). 625/50 Disc on, limit An attempt was made to play back a disc Use a disc recorded with the NTSC recorded with the PAL system when this system. unit is in 525(U) or 525(J) line mode (NTSC system). Disc Error! on, limit, off Normal playback is not possible because Use another disc. of a disc defect. You can check the state of a disc by checking playback condition marks (see page 36). a) With respect to setting of basic menu item 016 During control panel operations 124 Message in time Display data display condition a) Description KEY INHI.! on An operation button inhibited by Set the corresponding sub-item of extended menu item 118 “KEY INHIBIT” extended menu item 118 to “off.” was pressed while the KEY INH indicator was lit. See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. REMOTE! on A button was pressed while the remote control switch was set to “REMOTE.” 8-4 Alarms Action To operate from the front panel, wait until control by the remote device ends and then set the remote control switch to “LOCAL.” Message in time Display data display condition a) Description Action No Disc! on A button was pressed with no disc loaded. Operate after inserting a disc. No Disc! on, limit, off An attempt to delete a clip was made with no disc loaded. No Disc! on, limit, off An attempt to format a disc was made with no disc loaded. REC INHI.! on An attempt was made to record, display To perform these operations on the disc, an E-E picture, record an essence mark, set the Write Inhibit tab of the disc to the or add a quick scene selection sub clip. recording enabled position. REC INHI.! on An attempt was made to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip while extended menu item 310 “REC INHIBIT” was set to “on.” To perform these operations, set extended menu item 310 to “off.” See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. IMX50 Clip IMX40 Clip IMX30 Clip DVCAM Clip 4CHx24 Clip 8CHx16 Clip on, limit A recording or E-E display operation was To perform these operations on the disc, attempted on a disc recorded in a format change the setting of basic menu item 031. different from the setting of basic menu item 031 “RECORDING FORMAT.” See 7-2-2 “Basic Menu Operations” (page 94) about how to change this setting. REC INHI.! on, limit An attempt to save the current clip list was made while the REC INHI indicator was lit. REC INHI.! on, limit, off An attempt to delete a clip was made while the REC INHI indicator was lit. REC INHI.! on, limit, off An attempt to format a disc was made while the REC INHI indicator was lit. No Clip! on, limit A playback or search button was pressed for a disc containing no recorded clips. No Clip! on, limit, off An attempt was made to delete a clip from a disc containing no recorded clips. Disc Top! on The PREV button was pressed while stopped at the top of the disc, or an attempt was made to perform a highspeed reverse search. Disc End! on The NEXT button was pressed while stopped at the end of the disc, or an attempt was made to perform a highspeed forward search. MAX # Files on, limit, off The number of files on the disc had Insert a different disc with enough free reached the upper limit (5000), or there capacity. was not enough capacity in the General directory when an attempt was made to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip. Disc Full! on, limit, off An attempt was made to record or display an E-E picture when there was not enough free capacity on the disc, or when the number of recorded clips had reached the upper limit (300). To perform these operations, cancel all of the following write-protect settings. • Write Inhibit tab of the disc • Setting of extended menu item 310 “REC INHIBIT” • Mismatch between the recorded sections of the disc and the setting of basic menu item 031 “RECORDING FORMAT” These operations are not possible. Chapter 8 Maintenance and Troubleshooting 8-4 Alarms 125 Message in time Display data display condition a) Description Action MAX# SB CLP on, limit, off An attempt was made to add a sub clip These operations are not possible. when the number of registered sub clips had already reached the upper limit (300) of the specifications of this unit. CL OVER DUR on, limit, off An attempt was made to add a sub clip when the total duration of sub clips in the clip list had already reached the upper limit (24 hours) of the specifications of this unit. Run Salvage on, limit, off An attempt was made to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip on a disc which requires clip recovery (salvage). Try the operation again after executing the salvage function. For details, see 3-6-7 “Handling of Discs When Recording Does Not End Normally (Salvage Function)” (page 40). CNT mode! on A time code or user bits preset operation Try the operation again after selecting “TC” was attempted with “COUNTER” or “UB” with the COUNTER SEL button. selected by the COUNTER SEL button. TC EXT! on REGEN mode! on A time code or user bits preset operation Try the operation again after setting the was attempted with the INT/EXT/RP188 INT/EXT/RP188 switch to INT and the switch is set to EXT and the PRESET/ PRESET/REGEN switch to PRESET. REGEN switch is set to PRESET. See 7-3-2 “Extended Menu Operations” A time code or user bits preset operation (page 108) about how to make this setting. was attempted with the PRESET/ REGEN switch is set to REGEN. Chapter 8 Maintenance and Troubleshooting 126 REC-PAUSE! on A time code or user bits preset operation Try the operation again after stopping was attempted with recording paused. recording. REC mode! on, limit An attempt was made to switch video or audio signals during recording. REC mode! on, limit, off An attempt was made to display the system menu “DISC MENU” during recording. REC mode! on, limit The THUMBNAIL button was pressed during recording. REC mode! on, limit, off An attempt was made to display DRIVE MAINTENANCE in the maintenance menu during recording. No SEL List on, limit The SUBCLIP button was pressed without loading a clip list from the disc into the current clip list. Try the operation again after loading a clip list. For details, see 5-3-1 “Loading a Clip List From Disc Into Unit Memory” (page 68). No SUB Clip on, limit A button in the playback control section was pressed when there were no sub clips in the current clip list. Playback is not possible without a sub clip in the current clip list. SB CLP mode on, limit The SHIFT button and the THUMBNAIL button were pressed together with the SUBCLIP button lit. Press the SUBCLIP button, turning it off, and try the operation again. SUB CLIP NG on, limit The SHIFT and SET buttons were pressed together when IN and OUT points were not set correctly (the OUT point was set before the IN point, etc.). Set the IN and OUT points correctly and try the operation again. No List! on, limit, off An attempt was made to delete a clip list This operation is not possible. with no clip lists saved on the disc. 8-4 Alarms Message in time Display data display condition a) Description Action STOP ONCE! on, limit The SUBCLIP button was pressed during playback of a clip list. Try the operation again after stopping playback. STOP ONCE! on, limit, off An attempt was made to display the CLIP menu during playback. No EM Space on, limit, off Recording of an essence mark failed because the number of essence marks recorded on the disc reached the upper limit of the specifications of this unit. EM Full! on, limit, off An attempt was made to add an essence mark with the number of recorded essence marks at the upper limit of the specifications of this unit. Formatting! on, limit, off An attempt was made to display the DISC MENU page in the system menu during an auto format. Disc Damage on, limit, off An attempt was made to record, display This disc cannot be recorded. Exchange an E-E picture, record an essence mark, the disc. or add a quick scene selection sub clip when there was no free sparing area. Non AV Full on, limit, off An attempt was made to record, display Insert a different disc with enough free an E-E picture, record an essence mark, capacity. or add a quick scene selection sub clip when there was no free Non-Real-Time space. Index File! on, limit, off An attempt was made to record to a disc Exchange the disc for one that contains an containing an unsupported index file. index file supported by this unit. Alternatively, format the disc (see page 39). File System on, limit, off File System on, limit, off An attempt was made to record to a disc It may be possible to play back the disc, but with an unsupported file system. recording is not possible. Exchange the disc for one formatted in a file system An attempt was made to record to a disc supported by this unit. Alternatively, format when its file system was set to inhibit the disc (see page 39). recording. Use the PDZ-1 Proxy Browsing Software to delete unneeded essence marks. Wait until the end of the auto format. a) With respect to setting of basic menu item 016 Chapter 8 Maintenance and Troubleshooting During reception of commands from an external device connected to the REMOTE connector Message in time Display data display condition a) Description Action No Disc! on A recording, playback, search, or other command was received with no disc loaded. Try the operation again after loading a disc. REC INHI.! on A recording or E-E display command was received for a write-protected disc. Try the operation again after setting the Write Inhibit tab to the recording enabled position. REC INHI.! on A recording or E-E display command was received with extended menu item 310 “REC INHIBIT” set to “on.” Try the operation again after setting extended menu item 310 to “off.” See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. IMX50 Clip IMX40 Clip IMX30 Clip DVCAM Clip 4CHx24 Clip 8CHx16 Clip on, limit A recording or E-E display command was received with basic menu item for a disc recorded in a format different from the specification of basic menu item 031 “RECORDING FORMAT.” Try the operation again after changing the setting of basic menu item 031. See 7-2-2 “Basic Menu Operations” (page 94) about how to change this setting. 8-4 Alarms 127 Message in time Display data display condition a) Description Action Run Salvage A recording or E-E display command was received for a disc that needs clip recovery (salvage). Try the operation again after recovering clips from the disc (salvage function). on, limit See 3-6-7 “Handling of Discs When Recording Does Not End Normally (Salvage Function)” (page 40). Chapter 8 Maintenance and Troubleshooting 128 MAX # Files on, limit, off The number of files on the disc had Exchange the disc for one with enough reached the upper limit (5000), or there free capacity. was not enough capacity in the General directory when a command was received to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip. Disc Full! on, limit, off A command was received to record or display an E-E picture when there was not enough free capacity on the disc, or when the number of recorded clips had reached the upper limit (300). MAX# SB CLP on, limit, off A command was received to add a sub These operations are not possible. clip when the number of registered sub clips had already reached the upper limit (300) of the specifications of this unit. CL OVER DUR on, limit, off A command was received to add a sub clip when the total duration of sub clips in the clip list had already reached the upper limit (24 hours) of the specifications of this unit. Disc Damage on, limit, off A command was received to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip when there was no free sparing area. This disc cannot be recorded. Exchange the disc. Non AV Full on, limit, off A command was received to record, display an E-E picture, record an essence mark, or add a quick scene selection sub clip when there was no free Non-Real-Time space. Insert a different disc with enough free capacity. No Clip! on, limit A playback or search command was received for a disc containing no recorded clips. These operations are not possible. Disc Top! on A PREV or reverse high-speed search command was received with the disc stopped at the top. Disc End! on A NEXT or forward high-speed search command was received with the disc stopped at the end. TC EXT! on A time code or user bits preset command was received with the INT/ EXT/RP188 switch is set to EXT and the PRESET/REGEN switch is set to PRESET. REGEN mode! on A time code or user bits preset command was received with the PRESET/REGEN switch is set to REGEN. 8-4 Alarms Try the operation again after setting the INT/EXT/RP188 switch to INT and the PRESET/REGEN switch to PRESET. See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. Message in time Display data display condition a) Description Live Logg! A time code or user bit preset operation Set extended menu item 258 “LIVE was attempted with extended menu item LOGGING” to “off” before performing the 258 “LIVE LOGGING” set to “on.” operation. on, limit Action See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. REC RUN! on A time code or user bits preset Try the operation again after setting the Fcommand was received with the F-RUN/ RUN/R-RUN switch to F-RUN. R-RUN switch is set to R-RUN. See 7-3-2 “Extended Menu Operations” (page 108) about how to make this setting. REC-PAUSE! on A time code or user bits preset command was received with recording paused. REC mode! on, limit A command to switch video or audio signals was received during recording. REC mode! on, limit A command to switch audio channels was received during recording. Try the operation again after stopping recording. a) With respect to setting of basic menu item 016 During recording and editing operations Description Action Disc Error! on, limit, off Normal recording is not possible because of a disc defect. Use another disc. You can check the state of a disc by checking playback condition marks (see page 36). 525/60 sig! on, limit A 525 system SDI signal was input with this unit in 625 line mode (PAL system) and with “SDI” selected with the VIDEO INPUT SEL button. Input a 625 system SDI signal. 625/50 sig! on, limit A 625 system SDI signal was input with this unit in 525(U) or 525(J) line mode (NTSC system) and with “SDI” selected with the VIDEO INPUT SEL button. Input a 525 system SDI signal. A mode err! on, limit An editing operation was attempted on a recorded disc, when one of the following audio settings differed from the settings of this unit. • Number of quantizing bits and recording channels • Handling of digital audio signals (audio or non-audio) To edit this disc, change the following settings. • Maintenance menu item “AUDIO CONFIG” — “DATA LENGTH” • Maintenance menu item “AUDIO CONFIG” — “NON-AUDIO INPUT” Input a reference video signal to the player and recorder. Chapter 8 Maintenance and Troubleshooting Message in time Display data display condition a) See 7-4-2 “Maintenance Menu Operations” (page 114) about how to make these settings. ILL. REF! on, limit, off The playback system and recording system are not synchronized. ILL. REC! on, limit A sync error between encoder and input Contact your Sony service representative. signal occurred during recording. ILL. PLAY! on, limit An audio/video phase error occurred during playback. MEM. Full! on, limit A memory write error occurred. MEM. Empty on, limit Playback data in memory was lost, and playback stopped. 8-4 Alarms 129 Message in time Display data display condition a) Description Action List Exists An attempt was made to edit a clip referenced by sub clips. Delete all clip lists. on, limit, off See 5-3-2 “Deleting Clip Lists From a Disc” (page 69). Clip End! on, limit, off An attempt was made to edit across clip Editing across multiple clips is not possible. boundaries. Recording on, limit More time than normal is required for recording processing, because recording is being done while avoiding defects on the disc. Wait until recording finishes. a) With respect to setting of basic menu item 016 Alarms relating to audio and video signals Message in time Display data display condition a) Description Action REF NON-STD on, limit, off A signal other than a standard reference Input a standard reference video signal to video signal was input to the REF the REF VIDEO IN connector. VIDEO IN connector. No INPUT! on An attempt to record was made with no input video signal. Input a video signal, and select it. VIN NON-STD on Recording is being done with a signal other than a standard video signal input to the VIDEO IN connector. Input a standard video signal to the VIDEO IN connector. EMPHASIS! on An unsupported audio emphasis signal (“EMPHASIS ON” signal) was input. This unit does not support “EMPHASIS ON” audio signals. Input “EMPHASIS OFF” signal. a) With respect to setting of basic menu item 016 Alarms relating to sensors and drives Chapter 8 Maintenance and Troubleshooting Message in time Display data display condition a) Description Action HUMID! on, limit, off Condensation was detected in the unit. See 8-2 “Condensation” (page 121). FAN Stopped on, limit, off The motor of the main unit fan has stopped. Contact your Sony service representative. DR-FAN Stop on, limit, off The motor of a drive fan has stopped. High TEMP! on, limit, off Temperatures have risen within the unit. High TEMP! on, limit, off Temperatures have risen within a drive. Note The unit will operate, but continued use in this state will result in rising temperatures in the unit or drive, with the risk of fire or damage to the unit. a) With respect to setting of basic menu item 016 130 8-4 Alarms Appendixes 105 (4 1/4) Specifications Power requirements 100 V to 240 V AC, 50/60 Hz DC, battery Power consumption AC: 37W DC or battery: 31W Peak inrush current (1)Power ON, current probe method: 65 A (240 V), 30 A (100 V) (2)Hot switching inrush current, measured in accordance with European standard EN55103-1: 35 A (230 V) Operating temperature 0ºC to 40ºC (32ºF to 104ºF) Storage temperature –20ºC to +60ºC (–4ºF to +140ºF) Operating relative humidity 20% to 90% Mass 4.7 kg (10 lb 5 oz) External dimensions (w/h/d, excluding projections) 230 × 105 × 340mm (91/8 × 41/4 × 131/2 inches) 340 (13 1/2) General 230 (9 1/8) Unit: mm (inches) System Recording/Playback format Video MPEG IMX (50/40/30 Mbps), DVCAM (25 Mbps) Proxy video MPEG-4 1) Audio MPEG IMX: 16 bits/48 kHz (8 channels) or 24 bits/48 kHz (4 channels) DVCAM: 16 bits/48 kHz (4 channels) Proxy audio A-law (8/4 channels, 8 bits, 8 kHz) 1) The MPEG-4 Codec is a product of Ingenient Technologies, Inc. Recording/Playback time MPEG IMX 50 Mbps: 45 min. 40 Mbps: 55 min. 30 Mbps: 68 min. DVCAM 85 min. Search speed Jog mode Specifications 131 ±1 times normal speed Shuttle mode ±20 times normal speed Video performance Sampling frequency Y: 13.5 MHz, R–Y/B–Y: 6.75 MHz Quantization 10 bits/sample Analog composite input to analog composite output Bandwidth: 30 Hz to 4.5 MHz +0.5/–1.5 dB (NTSC), 25 Hz to 5.5 MHz +0.5/– 1.5 dB (PAL) S/N ratio: 53 dB or more Differential gain: 2% or less Differential phase: 2° or less Y/C delay: 20 ns or less K-factor (2T pulse): 2% or less Processor adjustment range Video level –∞ to +3 dB Chroma level –∞ to +3 dB Set up/black level ±30 IRE/±210 mV Chroma phase/hue ±30° System sync phase ±3 µs System SC phase ±200 ns Audio performance Frequency response 20 Hz to 20 kHz +0.5/–1.0 dB (0 dB at 1 kHz) Dynamic range More than 90 dB Distortion Less than 0.05% (at 1kHz) Head room 20/18/16/12 dB (Selectable with menu) Appendixes Input connectors Digital signal inputs SDI IN BNC type (×1) SDI format (270 Mbps), SMPTE 259M/ CCIR656-III DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4 BNC type (×2), complying with AES3id-1995 S400 (i.LINK) 6-pin (×1), complying with IEEE 1394 Analog video inputs REF VIDEO IN BNC type (×1) 132 Specifications VIDEO IN Black burst 0.286 V (NTSC), 0.3V (PAL), 75 Ω, negative sync Composite sync BNC type (×1), composite 1.0 Vp-p, 75 Ω, negative sync Analog audio inputs AUDIO IN 1/3, 2/4 XLR 3-pin, female (×2), +4/0/–3/–6 dBu (selectable with menu), 10 kΩ, balanced Time code input TC IN BNC type (×1), SMPTE time code, 0.5 Vp-p to 18 Vp-p, 3.3 kΩ, unbalanced (network) 100Base-TX/10Base-T RJ-45 type (×1) 100BASE-TX: complying with IEEE 802.3u 10BASE-T: complying with IEEE 802.3 Output connectors Digital signal outputs SDI OUT (SUPER) BNC type (×1) SDI format (270 Mbps), SMPTE 259M/ CCIR656-III DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4 BNC type (×2), complying with AES3id-1995 S400 (i.LINK) 6-pin (×1), complying with IEEE 1394 Analog video outputs VIDEO OUT 1, 2(SUPER) BNC type (×2), composite, 1.0 Vp-p, 75 Ω, sync negative Analog audio outputs AUDIO OUT 1/3, 2/4 XLR 3-pin, male (×2), +4/0/–3/–6 dBu (selectable with menu), 600 Ω loading, low impedance, balanced Output for headphones PHONES JM-60 Stereo phone jack (×1), –∞ to –13 dBu, 8 Ω, unbalanced Time code output TC OUT BNC type (×1), SMPTE time code, 2.2 Vp-p ±3 dB, 600 Ω, unbalanced Remote control connectors REMOTE D-sub 9-pin (×1), for connection of editing control unit, RS-422A standard S400 (i.LINK) 6-pin (×1), complying with IEEE 1394, supporting file access mode Power input/output connectors DC IN 12V XLR 4-pin, male (×1), 11 to 17 V DC DC OUT 12V 1) Round type 4-pin, female (×1) When driven by AC power: DC 14.5 V, Max. 5W When driven by DC power or battery: DC 11 to 17 V, Max. 5W 1) Use as power source for BVR-3 Remote Control Unit (not supplied) and RM-280 Editing Controller (not supplied). Others Video panel Picture: 3.5 type Pixel resolution: 211,200 pixels (960 wide × 220 high) Effective picture elements: more than 99.99% Design and specifications are subject to change without notice. Notes • Always make a test recording, and verify that it was recorded successfully. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE. • Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER. Accessories supplied Operation manuals English version (1) Japanese version (1) CD-ROM manual (1) PDZ-1 Proxy Browsing Software (1) Connector caps For ~AC IN/DC IN 12V connector (1) For AUDIO IN connectors (2) For AUDIO OUT connectors (2) For BNC connectors (12) For / S400 (i.LINK) connector (1) For REMOTE connector (1) For DC OUT 12V connector (1) Accessories not supplied Appendixes AC power cord • For the customers in the U.S.A and Canada Part No. 1-551-812-41 (125 V, 10 A, about 2.4 m) • For the customers in the United Kingdom Part No. 1-777-823-12 (250 V, 10 A, about 2.0 m) • For the customers in European countries other than the United Kingdom Part No. 1-551-631-61 (250 V, 10 A, about 2.0 m) Shoulder strap (Part No. A-6772-374-C) Related products Battery packs BP-GL95, BP-GL65, BP-L80S, BPL60S RM-280 editing controller Specifications 133 Using the Shoulder Belt The following figures show how to fit the shoulder belt (not supplied). Caution If you fit the shoulder belt incorrectly, the unit may fall down and cause body injury. Follow the procedures described below to fit or remove the shoulder belt. To fit the shoulder belt Press and pull up. To remove the shoulder belt While pressing down the indication PRESS, move the clip downwards to release it. Appendixes 134 Using the Shoulder Belt Notice Concerning the Software License of This Unit Thank you for your purchasing this Sony product. Please read the following notice before using the product. By installing, copying or otherwise using the product, you will be deemed to have understood and agreed to the content of the notice. Notice Concerning Software Governed by the GNU GPL/LGPL This product includes software to which the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”) applies. Under the terms of the GPL/LGPL, of which a copy is attached, you have the right to obtain, modify, and distribute copies of the source code of this software. Specific instructions for downloading the source code can be found at the following URL: http://www.sony.net/Products/Linux/ Please note that we cannot respond to inquiries regarding the content of the source code. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. Appendixes For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. Notice Concerning the Software License of This Unit 135 GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) Appendixes These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: 136 Notice Concerning the Software License of This Unit a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. Appendixes 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. Notice Concerning the Software License of This Unit 137 This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,REPAIR OR CORRECTION. Appendixes 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. Copyright © This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. 138 Notice Concerning the Software License of This Unit This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright © year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details. The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’, they could even be mouseclicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. , 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Appendixes Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages-typically libraries-of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. Notice Concerning the Software License of This Unit 139 For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing nonfree programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. Appendixes Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”. A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. 140 Notice Concerning the Software License of This Unit The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.) “Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. Appendixes (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. Notice Concerning the Software License of This Unit 141 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. Appendixes 6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable 142 Notice Concerning the Software License of This Unit containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. Appendixes 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as Notice Concerning the Software License of This Unit 143 to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY Appendixes 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 144 Notice Concerning the Software License of This Unit END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. Copyright © This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker. , 1 April 1990 Ty Coon, President of Vice That’s all there is to it! The BSD Copyright This product includes software to which the BSD license applies. Please note that we cannot respond to inquiries regarding the content of the source code. The BSD License Appendixes Copyright © The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. Notice Concerning the Software License of This Unit 145 THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes software thttpd to which the license below applies. Please note that we cannot respond to inquiries regarding the content of the source code. Copyright © 1995, 1998, 1999, 2000, 2001 by Jef Poskanzer . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes software ucd-snmp to which the license below applies. Please note that we cannot respond to inquiries regarding the content of the source code. ----- Part 1: CMU/UCD copyright notice: (BSD like) ----Copyright 1989, 1991, 1992 by Carnegie Mellon University Appendixes Derivative Work - 1996, 1998-2000 Copyright 1996, 1998-2000 The Regents of the University of California All Rights Reserved Permission to use, copy, modify and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appears in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written permission. CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, 146 Notice Concerning the Software License of This Unit NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. ----- Part 2: Networks Associates Technology, Inc. copyright notice (BSD) ----Copyright © 2001, Networks Associates Technology, Inc. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: • Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. • Neither the name of the NAI Labs nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ---- Part 3: Cambridge Broadband Ltd. copyright notice (BSD) ----Portions of this code are copyright © 2001, Cambridge Broadband Ltd. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Appendixes • Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. • The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Notice Concerning the Software License of This Unit 147 MPEG-4 Visual Patent Portfolio License This product is licensed under the MPEG-4 Visual Patent Portfolio License. For the personal and non-commercial use of a consumer for (i) encoding video in compliance with the MPEG-4 Visual Standard (“MPEG-4 Video”) and/or (ii) decoding MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed by MPEG LA to provide MPEG-4 Video. No license is granted or shall be implied for any other use. Additional information including that relating to promotional, internal and commercial uses and licensing may be obtained from MPEG LA, LLC. See http://www.mpegla.com Appendixes 148 MPEG-4 Visual Patent Portfolio License Glossary AES/EBU A standard established jointly by the AES (Audio Engineering Society) and EBU (European Broadcasting Union) for serial transmission of digital audio. Two channels of audio can be transmitted via a single connector. Clip A recording unit. Clips are created every time recording starts and stops. Clip list A list of locations in the material recorded on the disc, arranged in any order. Clips lists can be created with the scene selection function of this unit, and with the supplied PDZ-1 Proxy Browsing Software. Color subcarrier In a composite video signal, a signal superimposed upon the picture (luminance) information for the purpose of conveying the associated color information. Color and saturation information is conveyed by the phase and amplitude of the color subcarrier. Also called subcarrier. Composite video signal A video signal in which luminance and chrominance are combined along with timing reference “sync” information to make composite video. E-E mode Electric-to-Electric mode. When you operate a VDR in E-E mode, input video and/or audio signals pass Essence mark A type of metadata that may be set for a specified frame. For more efficient searches, XDCAM equipment records essence marks as part of Non-RealTime metadata, and uses them to display thumbnails. i.LINK Another name for the IEEE13941995 standards and their revisions. XDCAM uses the i.LINK interface to transfer DV streams by the AV/C protocol, and to read and write MPEG IMX and DVCAM data files by FAM (file access mode). Metadata Information about the properties of video and audio content. XDCAM records metadata such as UMIDs and essence marks, and the supplied PDZ-1 Proxy Browsing Software can be used to record information such as titles and comments. MXF Material eXchange Format. A file exchange format developed by the Pro-MPEG Forum. Equipment from different manufacturers can exchange files in this format. Non-audio General term for audio signals other than linear PCM, such as Dolby E 1) and Dolby Digital (AC-3).1) XDCAM can record non-audio as an input signal. 1) Dolby is a trademark of Dolby Laboratories. Non-drop-frame mode A mode of advancing time code which ignores the difference in frame values between real time and the time code. Using this mode produces a difference of approximately 86 seconds per day between real time and time code, which causes problems when editing programs in units of seconds using the number of frames as a reference. Proxy AV data Low-resolution data with a video bandwidth of 1.5 Mbps and an audio bandwidth of 64 kbps per channel. This unit records proxy AV data automatically whenever highresolution MPEG IMX or DVCAM data is recorded. Reference video signal A video signal that contains a sync signal or sync and burst signals, used as a reference for synchronization of video equipment. SDI Serial Digital Interface. An interface standardized as SMPTE 259M which enables the transmission of an uncompressed digital component stream. S/N Signal-to-Noise ratio. The relation of the strength of the desired signal to the accompanying electronic interference, the noise. If S/N is high, sounds are reproduced with less noise and pictures are reproduced clearly without snow. SNMP Simple Network Management Protocol. XDCAM uses this protocol to monitor equipment operating status via network connectors. Sub clip One of the sections which make up a clip list. A sub clip may be part of a clip or an entire clip. Thumbnail image A reduced still picture of video for display on a GUI screen. XDCAM creates thumbnail images from proxy video, and displays them as index pictures on GUI screens. Appendixes Drop frame mode SMPTE time code runs at 30 frames/ second, while the NTSC color television system runs at about 29.97 frames/second. Drop frame mode adjusts the running of time code to eliminate the discrepancy between time code value and actual time by dropping two frames from the time code value at the beginning of each minute except every tenth minute. through electric circuits only and then come out from the output connectors, without passing through electromagnetic conversion circuits such as recording heads. Time code A digitally encoded signal which is recorded with video data to identify each frame of the video by hour, minute, second and frame number. SMPTE time code is applied to NTSC system, and EBU time code to PAL and SECAM systems. Glossary 149 UMID Unique Material Identifier. A standard (SMPTE 330M) for video and audio metadata. The Basic section of a UMID contains a globally unique number and a material number for the identification of recorded material. An optional section called the “Source Pack” contains information such as the time and location of recording. A UMID with the Basic section only is called a Basic UMID. A UMID with the Source Pack is called an Extended UMID. User bits A total of 32 bits are provided in the time code which the user can use to record such information as date, reel number, or scene number on video tape. Also called user's bits. Appendixes 150 Glossary Index A AC IN connector 24 AC power inlet connector 11 switch 11 ACCESS indicator 12, 17 Accessories not supplied 133 supplied 133 AES/EBU 19 Alarms 122 list 122 ALL/CH-1, CH-2 to CH-4 adjustment knobs 15 ANALOG 19 Analog audio signal inputs/outputs 23 interfaces 10 video signal inputs/outputs 23 Appendixes 131 Arrow buttons 16 AUDIO IN 1/3, 2/4 connectors 23 METER SEL button 15 OUT connectors 23 Audio settings section 15 Audio and video settings section 19 AUDIO INPUT CH button 19 SEL button 19 Audio level meters 18 AUDIO MONITOR SEL button 15 Audio recording format setting 43 level adjustment 43 Auto clip list recording 48 Basic setup menu 90 items 90 operations 94 BATT display 18 Battery pack shoe 11 Battery packs 33 Built-in speaker (monaural) 11 C Carrying handle 11 E D H Date/time setting 34 DC IN 12V connector 24 DC OUT 12V connector 21 DC power, using 33 Digital audio signal inputs/outputs 22 hours meter 120 interfaces 10 DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4 connectors 22 OUT 1/2, 3/4 connectors 22 Disc loaded mark 19 DISC remaining capacity indicator 18 Discs formatting 39 handling 38 loading/unloading 38 status 118 usable discs 38 write-protecting 38 Display settings section 19 Drop frame mark 36 HOLD button 13 HOLD indicator 18 EJECT button 11 Ejecting a disc manually 39 Error Messages 121 Essence mark 53 Essence mark recording 48, 51 Extended setup menu 97 items 97 operations 108 External monitor connection 25 EXT-LK indicator 18 F Features of PDW-R1 9 File access mode file operations 78 File operations 72 directory structure 72 file access mode 78 FTP 80 restrictions 73 Formatting a disc 39 Forward high-speed search 16 Front panel 12 F-RUN/R-RUN switch 13 FTP command lists 82 file operations 80 G Glossary 149 I i.LINK connector 22 IN indicator 16 IN/OUT button 16 Indicators on back of LCD panel 17 Initial value 44 INT/EXT/RP188 switch 13 Interfaces 10 Index B CHARACTER switch 20 Clip 60 deleting 56, 118 locking 55 status 118 user-defined name 76 Clip List previewing 66 Clip list 60 CLIP menu 68 creating and editing 61 current clip list 60 deleting 69 managing 68 previewing 66 saving 66 sorting 70 user-defined name 76 Condensation 121 Configuration 11 Connections 25 Camcorder 27 cut editing system 29 external monitor 25 for using PDZ-1 25 nonlinear editing system 27 Connectors 11, 21 Control panel 11, 12 COUNTER 13 indicator 18 SEL button 13 Current clip list 60 Cut editing system connection 29 J Jog dial 14 mode 51 JOG button 14 Jog/shuttle control block 14 Jog/shuttle transport indicators 14 Index 151 K KEY INHI indicator 17 KEY INHI switch 12 L LCD panel 11, 17 Level adjustment 43 LEVEL knob 21 LIGHT switch 20 Line mode setting 7 Live logging function 71 Loading/unloading a disc 38 LOCAL 12 M Maintenance 72, 120 periodic 120 Maintenance menu 112 items 112 operations 114 MARK1/MARK2 button 16 MENU button 14 Menus 89 basic setup menu 90 configuration 89 extended setup menu 97 maintenance menu 112 system menu 117 Metadata 10 MONITOR switch 20 N Names and functions of parts 11 NDF indicator 18 NETWORK 12 access indicator 12 Network connector 22 NEXT button 16 Nonlinear editing system connection 27 O Index On/standby indicator 12, 17 switch 12 Operating mode selection/menu setting section 13 Operation mode 36 OUT indicator 16 Overview 9 Q Quick scene selection 62 R REC button 16 REC INHI indicator 18 Recording 42 essence mark 48, 51 format setting 42 level adjustment 43 operation 48 preparations 42 time code/user bits 44 Recording and playback control section 16 REF VIDEO IN connectors 22 Related products 133 REMOTE 12 connector 22 Remote control switch 12 Repeat playback 54 RESET button 14 Reverse high-speed search 16 RM-280 31 S P PB indicator 18 152 PDZ-1 25, 71 connections 25 installation 71 system requirements 71 Periodic maintenance 120 PHONES jack 21 PLAY button 16 Playback 49, 51 clip list 54 condition displays 37 jog mode 51 normal speed 51 preparations 49 repeat 54 shuttle mode 52 start position 49 Power AC power 33 battery packs 33 preparations 33 Power supply section 24 Preparations 25 PRESET/REGEN switch 13 PREV button 16 Proxy AV data 9 Proxy Browsing Software (See also “PDZ-1”) 25, 71 Index S400 connector 22 Salvage function 40 Scene selection 58 SDI 19 IN connector 23 OUT (SUPER) connectors 23 signal inputs/outputs 23 Security slot 11 SET button 14 Setup 34 SETUP BANK4 113 SG 19 SHIFT button 14 Shoulder belt posts 11 using 134 Shuttle dial 15 mode 52 SHUTTLE button 14 SNMP 10 Specifications 131 STATUS button 19 Status display 18 STOP button 16 Sub clip 60 deleting 66 reordering 63 trimming 65 SUBCLIP button 13 Superimposed text information (See also “Text information”) 35 System menu 117 items 117 operations 117 T TC 13 TC/VITC indicator 18 Text information 35 display adjustment 35 drop frame mark 36 information displayed 35 operation mode 36 TC generator drop frame mark 36 time data types 36 VITC field mark 36 THUMBNAIL button 13 Thumbnail image, setting 43 Thumbnail search 9, 52 TIME CODE IN connector 24 OUT connector 24 Time code initial value 44 inputs/outputs 24 recording 44, 88 Time data display 18 types 36 Time data settings section 13 Title 75 Troubleshooting 120 U UB/VIUB indicator 18 U-BIT 13 UMID data 109 User bit recording 44 V VARIABLE switch 15 VIDEO IN connectors 23 INPUT SEL button 19 OUT 1, OUT 2 (SUPER) connectors 23 Video panel 17 Video processing adjusting parameters 49 Video recording format setting 43 VITC field mark 36 indicator 18 W WARNING indicator 17 Write-protecting discs 38 Index Index 153 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. PDW-R1 Sony Corporation (SY) 3-991-786-02 (1) http://www.sony.net/ © 2006