Sound Crush HR-801 Twist Mini Wireless Speaker User Manual
Sound Crush Company Limited Twist Mini Wireless Speaker
User manual
HR-801 Twist Mini Wireless Speaker Sound Crush Company Limited What's Included: • HR-801 Twist Mini Wireless Speaker • Aux cable 3.5mm • USB Charging Cable • User's guide Specifications • Power Output: 3W • Dimensions (HxWxD ) 18x4.8 . x 4.8cm • Advanced Audio Distribution Profile (A2DP) for wireless music streaming • Hands-free Audio (HFP) and Headset Profiles (HSP) for hands-free calling capability • Range up to 10 meter • Battery life 4 to 5 hours of playing time depending on volume settings HR-801 Twist Mini Wireless Speaker How to connect the HR-801 to your Bluetooth device. 1. Make sure your speaker is charged ( follow charge instruction) 2. Press the power-mode button on top of the speaker for 3 seconds. The led will turn flash blue-red indicating it is searching , then solid blue indicating it is in Bluetooth mode. Paring button Vol controls- Power Vol controls + Play&pause Hands-free Calling Answer/End button Hands free Calling When your phone is connected to the HR-801 you can use the speaker a s a h nds-free device. To accept a call, push the phone button on the speaker. You can also accept the call as you usually do on your phone. Change Volume Press the volume up or down to adjust to your desired volume. You can also change the volume on your audio device Bluetooth button Press the button to disconnect or reconnect your Bluetooth speaker. Power LED indicator The led indicator is located on the left side of USB charging port of the speaker. When the LED is red the battery is charging. When the LED is flashing the battery is low. When the LED is off the battery is charged. Pause your music Push the play/pause button to play or pause your music. Charge the Built-in Li-Ion Battery Connect the mini USB cable at the back of the speaker. ( USB charging) Connect the other end of the cable to a USB port or to a USB AC adapter. ( not included) The red LED indicator will turn red when charging and will turn off when charging is finished. If at any time in the future you should need to dispose of thisproduct please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive) Warning Do not become distracted by this product while driving. Do not leave the product exposed to a heat source or high temperatures Do not remove or attempt to remove the Li-Ion battery 3. Check the instruction manual of your smartphone or other blue tooth device and make sure the Bluetooth function is on. Make sure your device is in search or discover mode. 4. Your device will find u, connect, the led on the speaker will becomes solid blue. 5. You can now start playing your music. How to connect the HR-801 without Bluetooth 1. Make sure your speaker is charged ( follow charge instruction) 2. Turn the speaker on with the main On-Off switch at the back of the speaker. 3. Press the power-mode button on top of the speaker for 3 seconds. 4. The led will turn flash blue-red indicating it is searching , then solid blue indicating it is in Bluetooth mode. Press the power button once more (short) the led will turn solid green. 5. Connect the supplied aux cable to the aux input at the back of the speaker. 6. Connect the other end to the headphone output ( 3.5mm) of your smartphone or other device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. www.mitone.eu This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2014:06:04 16:13:32+08:00 Creator Tool : Adobe Illustrator CS6 (Windows) Modify Date : 2016:04:08 14:41:37+08:00 Metadata Date : 2016:04:08 14:41:37+08:00 Thumbnail Width : 256 Thumbnail Height : 128 Thumbnail Format : JPEG Thumbnail Image : (Binary data 10214 bytes, use -b option to extract) GTS PDFX Conformance : PDF/X-1a:2001 GTS PDFX Version : PDF/X-1:2001 Version ID : 1 Document ID : xmp.did:0F7C7B0EC0EBE311A86CE6A8EA9E98DC Instance ID : uuid:50b6fbbb-c294-4732-aa7c-47565b0525e3 Original Document ID : xmp.did:FD1CC173B0BFE3119E6FD1DA23219757 Rendition Class : proof:pdf Derived From Instance ID : uuid:ce0ddcfd-8ffe-4ecc-8853-56161238f1d0 Derived From Document ID : xmp.did:7A42E527ABCEE3118C17AC91BAD9C5F9 Derived From Original Document ID: xmp.did:FD1CC173B0BFE3119E6FD1DA23219757 Derived From Version ID : 1 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:FD1CC173B0BFE3119E6FD1DA23219757, xmp.iid:0F7C7B0EC0EBE311A86CE6A8EA9E98DC History When : 2014:04:09 14:30:32+08:00, 2014:06:04 16:13:29+08:00 History Software Agent : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows) History Changed : /, / Producer : Adobe PDF library 10.01 Trapped : False Format : application/pdf Creator : Administrator Title : HR801说明书 N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 299.999948 Max Page Size H : 149.999974 Max Page Size Unit : Millimeters Font Name : Calibri, ArialMT, TimesNewRomanPSMT, AdobeSongStd-Light, Calibri,Bold Font Family : Calibri, Arial, Times New Roman, Adobe 宋体 Std, Calibri,Bold GBpc-EUC-H Font Face : Regular, Regular, Regular, L, GBpc-EUC-H Font Type : Open Type, Open Type, Open Type, Open Type, Unknown Font Version : Version 1.02, Version 3.00, Version 3.00, Version 5.010;PS 5.002;hotconv 1.0.57;makeotf.lib2.0.21895, Version 5.010;PS 5.005;hotconv 1.0.57;makeotf.lib2.0.21895 Font Composite : False, False, False, False, False Font File Name : CALIBRI.TTF, ARIAL.TTF, TIMES.TTF, AdobeSongStd-Light.otf, AdobeHeitiStd-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 2758 C Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Swatch Groups Colorants Cyan : 100.000000 Swatch Groups Colorants Magenta : 90.999997 Swatch Groups Colorants Yellow : 7.000000 Swatch Groups Colorants Black : 31.999999 Swatch Groups Colorants Swatch Name: PANTONE 429 C Swatch Groups Colorants Type : SPOT Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Mode : LAB Swatch Groups Colorants L : 69.019600 Swatch Groups Colorants A : -2 Swatch Groups Colorants B : -3 Page Count : 1 For : Administrator, Bounding Box : 0 0 851 426 Container Version : 11 Creator Version : 16 Author : Administrator Image Height : 426 Image Width : 851 Image Size : 851x426 Megapixels : 0.363EXIF Metadata provided by EXIF.tools