Southco H3EM68 Electronic Swinghandle User Manual J H3 EM 68 100 M revAx
Southco,. Inc Electronic Swinghandle J H3 EM 68 100 M revAx
Southco >
User Manual_rev
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1808581 |
| Application ID | aooT2J0O/JqqcuKKrC0Wdw== |
| Document Description | User Manual_rev |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 475.83kB (5947895 bits) |
| Date Submitted | 2012-10-05 00:00:00 |
| Date Available | 2012-09-11 00:00:00 |
| Creation Date | 2012-08-07 16:07:43 |
| Producing Software | ScanSoft PDF Create! 4 |
| Document Lastmod | 2012-08-07 16:07:45 |
| Document Title | Microsoft Word - J-H3-EM-68-100-M_revA.docx |
| Document Creator | Microsoft Word - J-H3-EM-68-100-M_revA.docx |
| Document Author: | bargeb |
H3-EM-68-100 Electronic Swinghandle Operating Instructions Package Contents Operating Transit Time: H3-EM-68-x00 Electronic Swinghandle with Proximity Reader (qty1) EM-0-45827 M3x25 Long Mounting Screws (qty 4) EM-0-47151 M3x14 Long Mounting Screw (qty 1) EM-0-45825 Rotation Limiter (qty 1) E5-C-04 Pawl Screw (qty 1) EM-0-45826 Top Mounting Bracket (qty 1) EM-0-45822 Bottom Mounting Bracket (qty 1) Operating Instructions (qty 1) Electronic Unlock Time: Open Collector Outputs: 1 second maximum (NOTE: Power must be present during transit times. If power is removed while the lock slide is moving to the unlock position, then the control input signal must be asserted again. If power is removed while the lock slide is moving to the lock position, it will complete it’s cycle when power is restored.) 3 seconds minimum Rated for VSUPPLY, 200mA maximum load Proximity Reader Module H3-EM-68-x00 Electronic Swinghandle with Proximity Reader Supply Voltage (VCC): Operating Current: 12VDC to 24VDC 20mA maximum (no external devices attached) Transmit Frequency: 125kHz FSK DATA Signal Voltage: 5VDC DATA Pulse Interval Time:40µs DATA Signal Delay: 2ms Mounting and Installation Please refer to Southco trade drawing J-H3-EM-68-100 for mounting and installation details. Wiring Diagrams The H3-EM-68-x00 contains two separate functional modules: the actuator module and proximity reader module. The actuator module controls and monitors the locking function of the swinghandle. The proximity module reads the contents of a compatible proximity card and converts it to Wiegand format. 1. 2. 3. 4. Handle Prox Reader Tri-Color Status LED Lock Plug These two modules operate independently of each other and require connection to an access control unit (not provided), as illustrated below, for the entire product to be fully functional. Features Installed 125kHz proximity reader module with Wiegand data output Remote lock and unlock capability Single or multi-point lock actuation Momentary or continuous lock actuation Tri-color LED (blue/magenta/red) to indicate lock and handle status High security DIN lock manual override Accommodates both left and right doors For indoor use only Specifications Actuator Module Supply Voltage (VSUPPLY): 12VDC to 24VDC (NOTE: Status LED will blink red if the supply voltage is out of range.) Standby Current: 50mA maximum at 12VDC Operating Current: 200mA maximum at 12VDC (with no external mechanical load applied to handle Stall Current: 1A maximum (at 12VDC, limited to 2 seconds) J-H3-EM-68-100-M_revA visit www.southco.com for latest version of this document Page 1 of 4 H3-EM-68-100 Electronic Swinghandle Operating Instructions The actuator module of the swinghandle is accessed with a six-position connector on the rear of the unit, shown below. Control Input Signal This signal is used to control the electronic lock slide position. for UNLOCKED position: Supply 9VDC minimum (do not exceed supply voltage) for at least 50 milliseconds. The lock will remain unlocked for as long as the signal is present, or a minimum of 3 seconds. Signal timing can typically be adjusted at the access control device. The control signal current draw is less than 10mA. for LOCKED position: Supply an open contact or 0VDC (0 to 0.5V) Electronic Lock Status Output and Mechanical Lock Status Output Signals Pin Description VGND VSUPPLY N/C Control Signal Electronic Lock Status Mechanical Lock Status Note ground (must be same as proximity reader module) 12 to 24 VDC power supply input (may be connected to prox reader VCC input) no connect command input (9VDC up to supply voltage, 50 milliseconds minimum) open collector output (rated for VSUPPLY, 200mA max. load) open collector output (rated for VSUPPLY, 200mA max. load) The proximity reader module of the swinghandle is accessed with a fourposition connector attached to a harness connected to the module’s circuit board. The module’s connector pinout is: Electronic Lock Status Output Signal This output will be LOW (GND) when the lock slide is electromechanically moved to the unlocked position. It will be in the open collector state (highimpedance) when in the locked position. Mechanical Lock Status Output Signal This output will be LOW (GND) when the handle is in the open position or when the keylock in the actuator is manually unlocked. It will be in the open collector state (high-impedance) when in the secured position. NOTE: These outputs are open collector outputs rated for VSUPPLY with a maximum load of 200mA. To avoid damage to the H3-EM, do not exceed voltage and current ratings. Status LED and Output Signals The latch is equipped with a tri-color (blue/magenta/red) LED visible from the front of the latch. This LED provides a visible notification of the latch status. The different latch states are described below. Please refer to the Control Input Signal, Electronic Lock Status Output Signal, and Mechanical Lock Status Output Signal sections for further details on these signals. Secured Pin Wire Color Black Description GND Red VCC Green White DATA0 DATA1 Note ground (must be same as actuator module) 12 to 24VDC power supply input (may be connected to EML VSUPPLY input) DATA0 output DATA1 output NOTE: The mating connectors/harnesses are not provided with the H3-EM-68-x00. Refer to Southco trade drawing J-H3-EM-68-100 for mating connector/harness requirements. The latch is securely closed, prohibiting access. The Status LED will be solid blue. The electronic lock status output is at its open collector state. The mechanical lock status output is at its open collector state. handle secured in housing, cam in locked position electronic lock slide in locked position “Secured” State J-H3-EM-68-100-M_revA visit www.southco.com for latest version of this document Page 2 of 4 H3-EM-68-100 Electronic Swinghandle Operating Instructions Electronically Released Handle not Fully Closed The electronic lock slide is in the unlocked position and the handle can be pulled open. The Status LED will alternate flashing blue/magenta. The electronic lock status output is 0V while the lock slide is in the unlocked position. The mechanical lock status output is at its open collector state. This is an interim state and may occur while closing the handle when the cam is not secured by the electronic lock slide. The latch is not fully secured during this state. The Status LED will alternate flashing blue/red if the cam is not detected. It will flash blue/red/red if the cam is detected, but the lock plate is not in the right position. This could be due to mechanical failure or tampering. The electronic lock status output is 0V if the lock slide is in the unlocked position. It will be at its open collector state if it is in the lock position. The mechanical lock status output is 0V if the cam is not detected. It will be at its open collector state if it is detected. electronic lock slide in unlocked position handle secured in housing, cam in locked position cam not detected by latch cam detected by latch “Electronically Released” State Mechanically Released The latch is released by opening the handle or moving the cam from its lock position. The Status LED will flash blue. The electronic lock status output will be at its open collector state “Handle not Fully Closed” State if the electronic lock slide is in the locked position. It will be 0V if the lock slide is in the unlocked position. Electronic Lock Slide Error The mechanical lock status output is 0V. The electronic lock slide does not respond to the command input signal. NOTE: The lock sensor is an optical device that senses the presence The Status LED will flash magenta if the latch is secured. It will of the lock pawl. Reflectivity of the lock pawl material can affect sensing. alternate flashing red/magenta if the latch is mechanically Use only Southco-supplied locks. released. The electronic lock status output is at its open collector state. The mechanical lock status output will be at its open collector state if the cam is in its lock position. It will be 0V if the mechanical key is moved from its lock position. electronic lock slide in locked position For technical support of this product contact: info@southco.com or visit: www.southco.com electronic lock slide in unlocked position lock plug in unlocked position “Mechanically Released” State J-H3-EM-68-100-M_revA visit www.southco.com for latest version of this document Page 3 of 4 H3-EM-68-100 Electronic Swinghandle Operating Instructions FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) 2) This device may not cause harmful interference and This device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning: The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Industry Canada Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le material brouilleur: “Appareils Numériques,” NMB-003 édictée par l’Industrie. J-H3-EM-68-100-M_revA visit www.southco.com for latest version of this document Page 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Creator : Microsoft Word - J-H3-EM-68-100-M_revA.docx Producer : ScanSoft PDF Create! 4 Create Date : 2012:08:07 16:07:43-05:00 Modify Date : 2012:08:07 16:07:45-05:00 Author : bargeb Title : Microsoft Word - J-H3-EM-68-100-M_revA.docx Page Count : 4 Page Mode : UseNone Page Layout : OneColumnEXIF Metadata provided by EXIF.tools