Spectrum 450241CBR Z-Wave Plus Module User Manual 910 Z Wave Plus indd

Spectrum Brands, Inc. Z-Wave Plus Module 910 Z Wave Plus indd

Users Manual 910

A BWFParts in the boxLatch“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.Exterior AssemblyStrike Adapter ring C D EKeysMounting PlateSmartKey Tool GH03809 46780 N Q SPFasteners48654 27526 64109Interior Assembly K L M T U VAN or P (2x)NPSQAABBBABIf drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.Note: Additional door preparation may be required for doors with 11/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.orbacksetMeasure to conirm that the hole in the door is either 21/8" (54 mm) or 11/2" (38 mm).Measure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).23/8" or 23/4"60 or 70 mm 13/8" – 13/4"*35 – 44 mm*Measure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 13/4"* (35 mm and 44 mm*) thick.AA BCDB C DIs the door edge chiseled?Is the D-shaped hole centered in the door hole?Which latch are you installing?Hold the latch in front of the door hole, with the latch face lush against the door edge.21/8"54 mm11/2"38 mm1"25 mmYESYESNONOUse latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.wood blockactual sizeUse latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown.Latch “A” Latch “B”S (2x) CQ (2x)Longer screws install closest to the door jamb.door frameEInstall strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.orchiseled not chiseledor1Prepare the door and check dimensions2Install the latch and strike*Service kits for 21/4" (57 mm) thick doors are available through Kwikset.No adjustment is required. Proceed to next step.D-shaped hole D-shaped holeRotate latch face as shown to extend latch.or1 / 466071001 Rev 01ZWave® PlusInstallation and User GuideENGLISHRequired toolsRuler4 AA BatteriesHammer Wood blockPhillips head screwdriverAdditional Tools (depending on application)Kwikset Technical Support1-866-863-6584www.kwikset.com
21/8"54 mm11/2"38 mmYES NOorDoor handing process was successful! Proceed to next step after latch bolt stops moving.Remove battery pack, wait 15 seconds, then attempt the process again.Remove battery cover. Remove battery pack. Make sure the turnpiece is in the vertical position.A B CverticalMLKLDo not install batteries until step 5.Note: Turnpiece may not rotate smoothly until after step 5.Connect cable. Ensure tight cable connection.Lay cable lat against the interior housing.Push turnpiece shaft onto torque blade.Secure interior assembly with supplied screws.D E F Gturnpiece shafttorque bladeThis step will teach your lock the orientation of your door and is crucial to lock operation.Install 4 AA batteries in battery pack. Press and HOLD the Lock button while installing battery pack.Hold button until the latch bolt starts moving on its own.Did the latch bolt retract and extend on its own when the battery pack was installed?A B C Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.KLU (2x)actual sizeTactual sizeU2 / 4What is the diameter of the hole in the door?Install exterior keypad and mounting plate.Insert cylinder into keypad.ABCDiameter is 21/8" (54 mm)Diameter is 11/2"(38 mm)or“D” is required for installation. Install “D” on “F”.“D” is not needed for installation. Discard “D”.Cable goes underneath latch.Locate screws and keep them within reach. Support exterior assembly during mounting plate installation.Route cable through center hole, then push cable into side hole. Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (T). Remove key when inished and make sure the latch bolt is fully extended.Keep parallel to edge of door.Tighten screws evenly.adbceDDFFTGT (2x)WFTE3Install the exterior keypad4Install the interior assembly5Install the batteries and perform the door handing process
1xgreen3xredInitiate the pairing process at your smart home controller. Refer to your smart home system instructions for more information. When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior one time. The red LED will illuminate when pairing mode has been entered. Please allow time for the controller to pair with the lock.If the pairing process is successful, re-name the lock in your system (if applicable).If pairing is unsuccessful, follow your system's instructions to remove the lock from the controller and any other network, then press button “A” on the lock one time. Perform steps 6A6C again.If pairing is still unsuccessful, consult the Programming and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com.A B CDbutton “A”Pair the lock with your smart home system3 / 4Conirm that the code(s) added in previous step can unlock the door.Make sure the door is open. Press the Program button the number of times that corresponds to the user code position being programmed. Locking the Door Unlocking the DoorEnter user code. A total of 30 user codes may be programmed.Press Lock button once.A B CWhat lights and sounds does the lock produce?DEach user code must be a unique code between 4 and 8 digits, depending on your smart home system.Example: If programming the third code, press the button three times.Programming was successful. Programming was unsuccessful. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Press Lock button once. Enter user code.It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here.Programming Timeout If no button is pressed for ive seconds, the system will time out and you will need to restart the procedure. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.MastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com.2xOne green lash with one beep* Three red lashes with three beeps* Two beeps*or orProgramming time out. Make sure not to pause for more than 5 seconds during programming.Tip: You can press the Lock button before entering your user code to light up the keypad at night.Re-key the lock (if needed). Install the battery cover.A BIMPORTANT: Remove battery pack before re-keying.KKMHactual sizeV V (3x)a ab bcRe-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.Reinstall battery pack.If your controller is S2-compatible, please refer to the S2 Pairing Guide on the SmartCode 910 page at www.kwikset.com.6789Add user codes (30 max)Re-key the lock (if needed) and install the battery coverTest the lock (review normal operation)
Alert Reason SolutionKeypad lashes red 1 time with 1 beep*Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.Keypad lashes red 3 times with 3 beeps*Unsuccessful programming. Attempt programming procedure again.One incorrect code entered. Re-enter code.No user code programmed. Program at least one user code.Keypad lashes red 10 times with 10 beeps* Low battery. Replace batteries.Lock beeps 2 times.Programming timeout.Attempt programming procedure again, making sure not to pause for more than 5 seconds.Keypad lashes red 3 times.Keypad lashes red 6 times with 6 beeps*.Keypad lashes red 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second keypad lockout.*Beeping sound will only be heard if switch #3 is on.Removing the lock from the networkFollow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once.Network InformationZWave System NotesThis product is a security enabled Z-wave Plus product and must be used with a Security Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35 feet+ being typical installed distance from smart home controller. It may be necessary to install additional ZWave beaming capable devices that can serve as repeaters to enhance the communication path between the lock and controller for a more robust ZWave network.To assure interoperability, each ZWave product must pass a stringent conformance test to assure that it meets the ZWave standard for complete compliance with all other devices and controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers that their products will reliably perform with any other ZWave device. And, regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.ZWave Coniguration and Association Parameters are available on the SmartCode 910 page at www.kwikset.com.© 2016 Spectrum Brands, Inc.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode.5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Important Safeguards4 / 4SmartCode at a GlanceDeleting a user codeIn order to delete a user code, you must override the code by adding a di erent user code in the same position. For example, if you want to delete the third code, add a di erent user code in position three. Test the old user code to make sure it can no longer unlock the door.If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock.Reference GuideExteriorBack panelProgram buttonStatus LEDSwitchesTurnpieceInterior (cover removed)Switches and Status LED colors TroubleshootingSwitch Function1Door lock status LED blinks every 6 seconds2Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.3 Audio4 Not used.Color Lock StatusBlinking green UnlockedBlinking amber LockedBlinking red Low batterySolid redDoor handing process did not work properly. See the online Programing and Troubleshooting Guide.1 2 3 4OnSwitchesStatus LEDO System AlertsFactory ResetA factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.Status LED1 Remove battery pack.2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.KeypadLock buttonKeywaySmartKey tool holeButton “A” Button “B”3 Press the Program button once more. When the LED lashes green and you hear one beep, the lock has been reset.4 Perform the door handing process again to teach the lock the orientation of the door, pair the lock with your smart home system, and add user codes to your lock. A complete Programming and Troubleshooting Guide is available on the SmartCode 910 page at www.kwikset.com.

Navigation menu