Spectrum 450248CBR Value Home Connect, Z-Wave Plus User Manual VHC KW VIVINT ENG indd

Download:
Mirror Download [FCC.gov]
Document ID	3280619
Application ID	ud1jIHYhDKknfAuG1yYgxw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	382.32kB (4778982 bits)
Date Submitted	2017-02-10 00:00:00
Date Available	2017-02-10 00:00:00
Creation Date	2016-12-08 06:56:10
Producing Software	Acrobat Distiller 15.0 (Windows)
Document Lastmod	2017-02-10 09:55:30
Document Title	VHC KW VIVINT ENG.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	SAD0418

61890 / 01
Regulatory Compliance
Cumplimiento Normativo
Conformité règlementaire
This product complies with standards established by the following
regulatory bodies:
Este producto cumple con las normas establecidas por los
siguientes organismos reguladores:
Ce produit est conforme aux normes établies par les organismes de
règlementation suivants :
•
•
•
•
•
•
Federal Communications Commission (FCC)
Industry Canada
Comisión Federal de Comunicaciones (FCC)
Industry Canada
Federal Communications Commission (FCC)
Industrie Canada
FCC
FCC
FCC
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: ( 1 ) this device may
not cause harmful interference, and ( 2 ) this device must accept
any interference received, including interference that may cause
undesired operation.
Este dispositivo cumple con la 15ª parte del reglamento de la FCC.
Su funcionamiento está sujeto a las siguientes dos condiciones:
( 1 ) este dispositivo no deberá causar ninguna interferencia dañina,
y ( 2 ) este dispositivo deberá aceptar cualquier interferencia
recibida, incluyendo aquélla que podría causar un funcionamiento
no deseado.
Cet appareil est conforme aux limites prescrites dans la partie 15
des règlements de la Federal Communication Commission (FCC)
des États-Unis. Son utilisation est subordonnée aux conditions
suivantes : ( 1 ) l’appareil ne doit pas causer d’interférence nuisibles,
et ( 2 ) il doit accepter toute interférence, y compris celles qui
peuvent causer son mauvais fonctionnement.
Se realizaron pruebas a este equipo cuyos resultados revelaron que
cumple con los límites establecidos para un dispositivo digital de
la Clase B, conforme a la 15ª parte del reglamento de la FCC. Estos
límites han sido impuestos para proporcionar protección razonable
contra interferencias dañinas en una instalación residencial. Este
equipo genera, utiliza y puede irradiar energía de radiofrecuencia
y, si no se instala y utiliza según lo que indican las instrucciones,
podría causar interferencia dañina en radiocomunicaciones. Sin
embargo, no hay garantía de que la interferencia no ocurrirá en
determinadas instalaciones. Si este equipo efectivamente causa
interferencia en la recepción de radio o televisión, la cual puede
determinarse encendiendo y apagando el equipo, sugerimos al
usuario que intente corregir dicha interferencia tomando una o más
de las siguientes medidas:
Lors des tests effectués, cet appareil s’est révélé conforme aux
limites prescrites dans la partie 15 des règlements de la Federal
Communications Commission (FCC) des États-Unis pour un
appareil numérique de Classe B. Ces limites ont été fixées pour
protéger raisonnablement les installations résidentielles contre les
interférences nuisibles. L’appareil produit, utilise et peut émettre
des radiofréquences. S’il n’est pas installé et utilisé de la façon
prescrite, il peut brouiller les communications radio. Il n’est pas
garanti qu’aucune interférence ne se produira. Si l’appareil brouille
la réception d’une radio ou d’un téléviseur (pour savoir s’il est
à l’origine du brouillage, il suffit de l’éteindre et de le rallumer),
l’utilisateur est invité à tenter de corriger la situation en prenant une
ou plusieurs des mesures suivantes :
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
IMPORTANT! Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the
equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
( 1 ) this device may not cause interference, and ( 2 ) this device
must accept any interference, including interference that may
cause undesired operation of the device.
•
•
•
•
Volver a orientar o ubicar la antena receptora.
Incrementar la distancia entre el equipo y el recibidor.
Conectar el equipo a una toma de corriente en un circuito
distinto del circuito en el cual esté conectado el recibidor.
Consultar con el distribuidor o un técnico de radio y TV con
experiencia para obtener su ayuda.
¡IMPORTANTE! Todo cambio o modificación no aprobado
expresamente por el fabricante podría desautorizar al usuario para
operar el equipo.
Industria de Canada
Este dispositivo cumple con las normas de la Industria de Canada
licencia-exenta RSS. Su funcionamiento está sujeto a las siguientes
dos condiciones: ( 1 ) este dispositivo no deberá causar ninguna
interferencia dañina, y ( 2 ) este dispositivo deberá aceptar
cualquier interferencia, incluyendo aquélla que podría causar el
funcionamiento no deseado del dispositivo.
•
•
•
•
réorienter ou déplacer l’antenne réceptrice;
éloigner davantage l’appareil émetteur du récepteur;
brancher l’appareil dans une prise reliée à un circuit différent
de celui auquel le récepteur est relié;
consulter le détaillant ou un technicien de radiotélévision
expérimenté pour obtenir de l’aide.
IMPORTANT! Les modifications qui n’ont pas été expressément
approuvées par le fabricant de l’appareil peuvent annuler
l’autorisation d’utiliser l’appareil.
Industrie Canada
Cet appareil est conforme aux normes d’Industrie Canada exemptes
de licence RSS. L’opération est sujette aux deux conditions: ( 1 ) ce
dispositif peut ne pas causer l’interférence et ( 2 ) ce dispositif doit
accepter n’importe quelle interférence, y compris l’interférence qui
peut causer le fonctionnement non souhaité du dispositif.
66455-001
Rev 01
Vivint
Z-Wave® Plus
Parts in the box
Latch
Interior Assembly
Exterior Assembly
ENGLISH
Strike
Required tools
4 AA Batteries
Mounting
Plate
Wood block
46780
Adapter
Ring
1-866-863-6584
www.kwikset.com
Additional Tools (depending on application)
03809
Kwikset
Technical Support
Phillips head screwdriver
Hammer
Fasteners
Keys
Ruler
“B” is not included. If needed,
please contact Kwikset to order
a drive-in latch for your lock.
Installation and User Guide
SmartKey
Tool
66128
49191
64109
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.
Measure to confirm that the hole in
the door is either 2-1/8" (54 mm) or
1-1/2" (38 mm).
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm).
2-3/8" or 2-3/4"
60 or 70 mm
2-1/8"
ba
ck
se
Measure to confirm that the hole in
the door edge is 1" (25 mm).
Measure to confirm that the door is
between 1-3/8" and 2" (35 mm and
51 mm) thick.
1-3/8" – 2"
35 – 51 mm
54 mm
1"
or
25 mm
1-1/2"
38 mm
Note: Additional door preparation may be
required for doors with 1-1/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep.
actual
size
Install the latch and strike
Is the door edge chiseled?
YES
Hold the latch in front of the door hole, with the latch
face flush against the door edge.
Latch “A”
NO
chiseled
Use latch “A”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.
or
Which latch are you installing?
or
not
chiseled
Use latch “B” (not
included). If the latch
bolt is not already
extended, extend the
latch bolt as shown.
Latch “B”
Is the D-shaped hole centered in the door hole?
YES
N or P
(2x)
NO
wood
block
or
D-shaped hole
D-shaped hole
No adjustment is required.
Proceed to next step.
Rotate latch face as
shown to extend latch.
Install strike on the door frame.
Make sure the hole in the door frame is drilled a
minimum of 1" (25 mm) deep.
Longer screws
install closest to
the door jamb.
S (2x)
Q (2x)
1/4
door frame
3
actual
size
Install the exterior keypad
What is the diameter of the hole in the door?
Diameter is 2-1/8"
(54 mm)
Install exterior keypad and mounting plate.
Diameter is 1-1/2"
(38 mm)
Support exterior
assembly during
mounting plate
installation.
or
2-1/8"
1-1/2"
54 mm
38 mm
“D” is required for installation.
Install “D” on “F”.
“D” is not needed for
installation. Discard “D”.
Cable goes
underneath latch.
Keep parallel to
edge of door.
Insert key and
test latch. If latch
does not extend or
retract smoothly,
adjust screws (T).
Locate screws for step 3C and keep them within reach.
Tighten
screws evenly.
Route cable through
center hole, then push
cable into bottom hole.
Remove key when
finished and make
sure the latch bolt
is fully extended.
T (2x)
actual
size
Install the interior assembly
Remove battery cover and battery pack from interior assembly.
Install interior assembly onto mounting plate.
align
Make sure turnpiece is in
the vertical position.
Ensure tight cable
connection.
Lay excess cable flat inside the
bottom of the interior housing.
Make sure
turnpiece shaft is
rotated as shown.
(2x)
Do not install
batteries
until step 5.
bottom
hole
Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
Install 4 AA batteries in battery pack.
Make sure the door is open, and
insert the battery pack.
After a few seconds, the latch bolt will retract and extend on
its own to learn the orientation of the door. This is called the
door handing process, and it is crucial to lock operation.
Status LED will indicate
success or failure.
Success: LED flashes green
Failure: LED remains solid red
Note: Latch
bolt will only
retract half way.
If the latch bolt does not move on its own, or if the Status LED indicates
a door handing failure, make sure the cables are connected, the
batteries are installed correctly, and attempt this procedure again.
If the door handing process is still unsuccessful after a second
attempt, perform the “Manual Door Handing” procedure on page 4.
Ensure correct polarity.
For best results, use
new, non-rechargeable
Alkaline batteries only.
2/4
6
Add the lock to your smart home system
Initiate the process to add
the lock to your system at
your smart home controller.
Refer to your smart home
system instructions for
more information.
When prompted by your smart home system to add the
lock, press button “A” on the lock interior one time. The
red LED will illuminate when the lock enters Add Mode.
If successful, re-name the lock in your system (if applicable).
If unsuccessful, follow your system's instructions to remove
the lock from the controller and any other network, then press
button “A” on the lock one time.
button “A”
Perform steps 6A-6C again.
If still unsuccessful, consult the Programming
and Troubleshooting Guide on the
SmartCode 888 page at kwikset.com.
Please allow time for the controller to add the lock.
Add user codes (30 max)
It is recommended that you add and
delete all user codes through your smart
home control system. If your system
does not allow this, codes may be added
directly to the lock as shown here.
Make sure the door is open. Press
the Program button once.
Enter user code. A total of 30 user
codes may be programmed.
Press Lock button once.
Each user code
must be a unique
code between
4 and 8 digits,
depending on
your smart
home system.
Programming Timeout
During programming, if no button is
pressed for five seconds, the system will
time out (indicated by three beeps and
a red flashing lock button), and you will
need to restart the procedure.
What lights and sounds does the lock produce?
Mastercode
Lock button flashes green once with one beep
Lock button flashes three times with three beeps
or
For enhanced security, a
mastercode may be used
when adding and deleting user
codes. For more information
about the mastercode,
download the Programming
and Troubleshooting Guide
on the SmartCode 888
page at kwikset.com.
red
green
1x
3x
Programming was successful.
Programming was unsuccessful.
Make sure not to pause for more than 5 seconds during programming.
Make sure the user code is not a duplicate and that it is between 4 and 8 digits
during your next attempt. Make sure the lock has room for an additional code.
If all user code positions are filled, delete a code to make room for this one.
Test the lock (review normal operation) and re-key the lock (if needed)
Confirm that the code(s) added in previous step can unlock the door.
Locking the Door
Unlocking the Door
Press Lock
button once.
Re-Key with SmartKey
Enter user code.
Re-key the lock
to work with your
existing key. See
the supplied
SmartKey Re-key
instructions for
more information.
actual
size
Install the interior cover
Install the interior cover.
Secure the interior cover with three (3) screws.
V (3x)
3/4
Note: To access the battery pack or back panel,
slide up the window on the interior cover.
Reference Guide
SmartCode 888 at a Glance
System Alerts
Interior (cover removed)
Back
panel
Exterior
Keypad
Deleting a single user code
Note: All codes may be deleted at once if the mastercode
is enabled. For more information about the mastercode,
consult the Programming and Troubleshooting Guide.
Alert
Reason
Solution
Lock button flashes
red once with one
beep*.
One incorrect code
entered.
Re-enter code.
No user code
programmed.
Program at least one
user code.
If no button is pressed for five seconds, the system will time
out, and you will need to restart the procedure.
Button “A”
Program
button
Lock
button
Status
LED
Keyway
Lock button flashes
red three times with
three beeps*.
Unsuccessful
programming.
Turnpiece
shaft
SmartKey
tool hole
Note: When the cover is
removed, the turnpiece shaft
can be used to manually
lock and unlock the door.
Troubleshooting
A complete Programming and Troubleshooting Guide is
available on the SmartCode 888 page at www.kwikset.com.
Programming timeout
after five seconds.
1. Press Program button once.
2. Press Lock button once.
3. Enter user code to be deleted.
4. Press Lock button once.
5. Re-enter user code.
6. Press Lock button once.
Attempt programming
procedure again.
Lock button flashes
red 15 times with 15
beeps*
Three incorrect codes
entered within one
minute.
Re-enter code after
60 second keypad
lockout.
Lock button flashes
red with fast beeping
sound for three to four
seconds.
Low battery.
Replace batteries.
Lock button flashes
green with continuous
beeping sound for two
seconds.
Door jammed while
attempting to lock.
Manually re-lock door.
If needed, reposition
strike.
If unsuccessful: Make sure to enter the same valid code in steps 3 and 5.
Test code: While the door is open, test the user code
to make sure it no longer unlocks the door.
Status LED
Auto-Lock
The Status LED blinks every 6
seconds to communicate whether
the door is locked or unlocked.
This feature is on by default.
Auto-lock automatically re-locks the door after unlocking. This feature is set to 30 seconds and is turned off by default.
Turn Auto-Lock On/Off
Blinking Green: Unlocked
Change Auto-Lock Time Delay
1. Press Program button once.
2. Press button “A” once.
1. Press Program button once.
3. Press button “3-4” multiple
times if needed to reach
desired state.
4. Press Lock button once.
3. Press button
“9-0” once.
2. Press button “A” once.
Status
LED
Blinking Amber: Locked
Blinking Red: Low battery
Solid Red: Unsuccessful door handing
process. See online Programming
and Troubleshooting Guide.
4. Press button once
that corresponds
to desired
time delay:
5. Press Lock
button once.
“1-2” – 30 sec.
Turn Status LED On/Off
“3-4” – 60 sec.
1. Press Program button once.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
2. Press button “A” once.
“5-6” – 90 sec.
“7-8” – 120 sec.
“9-0” – 180 sec.
3. Press button “1-2” multiple
times if needed to reach
desired state.
4. Press Lock button once.
Mute/Unmute Audio
Audio is on by default.
1. Press Program button once.
2. Press button “A” once.
3. Press button “5-6” multiple times if
needed to reach desired state.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
Manual Door Handing
Factory Reset
If needed, the door handing process can be initiated manually.
This is useful if the lock is being moved to a different door.
A factory reset will delete all codes associated with the lock, and it will
remove it from your smart home system.
2. Press and HOLD the Program
button while reinserting the
battery pack.
Release button once battery
pack is installed. The status
LED will flash red and green.
1. Remove battery pack.
3. Press the
Program
button once
more.
4. Press Lock button once.
4. The latch bolt will extend
and retract to learn the
orientation of the door.
The Status LED will indicate
success or failure.
1. Remove battery pack.
Status
LED
Success: LED flashes green
Failure: LED remains solid red
3. Press the Program button
once more. When the LED
flashes green and you hear
one beep, the lock has been
reset.
If the Status LED indicates a failure,
see the online Programming
and Troubleshooting Guide
or call Technical Support.
Network Information
2. Press and HOLD the Program
button while reinserting the
battery pack.
Keep holding the button
for 30 seconds until
the lock beeps and the
status LED flashes red.
Status
LED
4. After a few seconds, the lock will initiate the door
handing process, and the latch bolt will extend
and retract to learn the orientation of the door.
Important Safeguards
1.
2.
3.
4.
5.
Removing the lock from the network
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on
the lock interior once.
Z-Wave System Notes
Read all instructions in their entirety.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Protect your user codes and mastercode.
Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can
change the user codes, you must restrict access to the back panel and routinely check the
user codes to ensure they have not been altered without your knowledge. The use of a
mastercode can help protect your system’s settings.
This product is a security enabled Z-wave Plus product and must be used with a Security
Enabled Z-Wave controller to be fully utilized. Z-Wave is a “Wireless mesh network,” and
results may vary based on building construction and communication path.
WARNING: This Manufacturer advises that no lock can provide complete security by itself.
This lock may be defeated by forcible or technical means, or evaded by entry elsewhere
on the property. No lock can substitute for caution, awareness of your environment, and
common sense. Builder’s hardware is available in multiple performance grades to suit the
application. In order to enhance security and reduce risk, you should consult a qualified
locksmith or other security professional.
To assure interoperability, each Z-Wave product must pass a stringent conformance test to
assure that it meets the Z-Wave standard for complete compliance with all other devices and
controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other Z-Wave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available on
the SmartCode 888 page at www.kwikset.com.
4/4
© 2016 Spectrum Brands, Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : SAD0418
Create Date                     : 2016:12:08 06:56:10-08:00
Modify Date                     : 2017:02:10 09:55:30-08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:02:10 09:55:30-08:00
Producer                        : Acrobat Distiller 15.0 (Windows)
Format                          : application/pdf
Title                           : VHC KW VIVINT ENG.indd
Creator                         : SAD0418
Document ID                     : uuid:a5abfbd0-b8f5-413c-8525-5876a2036656
Instance ID                     : uuid:ac3cfc50-07b3-4514-b44d-13793cbc9808
Page Count                      : 5

EXIF Metadata provided by EXIF.tools