Spectrum 450248CBR Value Home Connect, Z-Wave Plus User Manual VHC KW VIVINT ENG indd

Spectrum Brands, Inc. Value Home Connect, Z-Wave Plus VHC KW VIVINT ENG indd

Contents

Users Manual

Regulatory ComplianceThis product complies with standards established by the following regulatory bodies:• Federal Communications Commission (FCC)• Industry CanadaFCCThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.IMPORTANT! Changes or modiications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.Industry CanadaThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any interference, including interference that may cause undesired operation of the device.Cumplimiento NormativoEste producto cumple con las normas establecidas por los siguientes organismos reguladores:• Comisión Federal de Comunicaciones (FCC)• Industry CanadaFCCEste dispositivo cumple con la 15ª parte del reglamento de la FCC. Su funcionamiento está sujeto a las siguientes dos condiciones: ( 1 ) este dispositivo no deberá causar ninguna interferencia dañina, y ( 2 ) este dispositivo deberá aceptar cualquier interferencia recibida, incluyendo aquélla que podría causar un funcionamiento no deseado.Se realizaron pruebas a este equipo cuyos resultados revelaron que cumple con los límites establecidos para un dispositivo digital de la Clase B, conforme a la 15ª parte del reglamento de la FCC. Estos límites han sido impuestos para proporcionar protección razonable contra interferencias dañinas en una instalación residencial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y utiliza según lo que indican las instrucciones, podría causar interferencia dañina en radiocomunicaciones. Sin embargo, no hay garantía de que la interferencia no ocurrirá en determinadas instalaciones. Si este equipo efectivamente causa interferencia en la recepción de radio o televisión, la cual puede determinarse encendiendo y apagando el equipo, sugerimos al usuario que intente corregir dicha interferencia tomando una o más de las siguientes medidas:• Volver a orientar o ubicar la antena receptora.• Incrementar la distancia entre el equipo y el recibidor.• Conectar el equipo a una toma de corriente en un circuito distinto del circuito en el cual esté conectado el recibidor.• Consultar con el distribuidor o un técnico de radio y TV con experiencia para obtener su ayuda.¡IMPORTANTE! Todo cambio o modiicación no aprobado expresamente por el fabricante podría desautorizar al usuario para operar el equipo.Industria de CanadaEste dispositivo cumple con las normas de la Industria de Canada licencia-exenta RSS. Su funcionamiento está sujeto a las siguientes dos condiciones: ( 1 ) este dispositivo no deberá causar ninguna interferencia dañina, y ( 2 ) este dispositivo deberá aceptar cualquier interferencia, incluyendo aquélla que podría causar el funcionamiento no deseado del dispositivo.Conformité règlementaireCe produit est conforme aux normes établies par les organismes de règlementation suivants :• Federal Communications Commission (FCC)• Industrie CanadaFCCCet appareil est conforme aux limites prescrites dans la partie 15 des règlements de la Federal Communication Commission (FCC) des États-Unis. Son utilisation est subordonnée aux conditions suivantes : ( 1 ) l’appareil ne doit pas causer d’interférence nuisibles, et ( 2 ) il doit accepter toute interférence, y compris celles qui peuvent causer son mauvais fonctionnement. Lors des tests eectués, cet appareil s’est révélé conforme aux limites prescrites dans la partie 15 des règlements de la Federal Communications Commission (FCC) des États-Unis pour un appareil numérique de Classe B. Ces limites ont été ixées pour protéger raisonnablement les installations résidentielles contre les interférences nuisibles. L’appareil produit, utilise et peut émettre des radiofréquences. S’il n’est pas installé et utilisé de la façon prescrite, il peut brouiller les communications radio. Il n’est pas garanti qu’aucune interférence ne se produira. Si l’appareil brouille la réception d’une radio ou d’un téléviseur (pour savoir s’il est à l’origine du brouillage, il suit de l’éteindre et de le rallumer), l’utilisateur est invité à tenter de corriger la situation en prenant une ou plusieurs des mesures suivantes :• réorienter ou déplacer l’antenne réceptrice;• éloigner davantage l’appareil émetteur du récepteur;• brancher l’appareil dans une prise reliée à un circuit diérent de celui auquel le récepteur est relié;• consulter le détaillant ou un technicien de radiotélévision expérimenté pour obtenir de l’aide.IMPORTANT! Les modiications qui n’ont pas été expressément approuvées par le fabricant de l’appareil peuvent annuler l’autorisation d’utiliser l’appareil.Industrie CanadaCet appareil est conforme aux normes d’Industrie Canada exemptes de licence RSS. L’opération est sujette aux deux conditions: ( 1 ) ce dispositif peut ne pas causer l’interférence et ( 2 ) ce dispositif doit accepter n’importe quelle interférence, y compris l’interférence qui peut causer le fonctionnement non souhaité du dispositif.61890 / 01
1 / 466455001Rev 01VivintZWave® PlusInstallation and User GuideENGLISHIf drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.Note: Additional door preparation may be required for doors with 11/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.orbacksetMeasure to conirm that the hole in the door is either 21/8" (54 mm) or 11/2" (38 mm).Measure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).23/8" or 23/4"60 or 70 mm 13/8" – 2"35 – 51 mmMeasure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 2" (35 mm and 51 mm) thick.A B C D21/8"54 mm11/2"38 mm1"25 mm1Prepare the door and check dimensionsRequired toolsRuler4 AA BatteriesHammer Wood blockPhillips head screwdriverAdditional Tools (depending on application)AN or P (2x)NPSQABBA DIs the door edge chiseled? Which latch are you installing?YES NOUse latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.wood blockactual sizeUse latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown.Latch “A” Latch “B”S (2x) CQ (2x)Longer screws install closest to the door jamb.door frameEInstall strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.orchiseled not chiseledor2Install the latch and strikeKwikset Technical Support1-866-863-6584www.kwikset.comABABBCIs the D-shaped hole centered in the door hole?Hold the latch in front of the door hole, with the latch face lush against the door edge.YES NONo adjustment is required. Proceed to next step.D-shaped hole D-shaped holeRotate latch face as shown to extend latch.orLatch“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.StrikeCKeysE A BExterior AssemblyAdapter Ring DMounting PlateParts in the boxFasteners03809 46780 N Q SP66128 64109 T V49191 UInterior AssemblySmartKey ToolHMFKLG
Uactual size21/8"54 mm11/2"38 mmKStatus LED will indicate success or failure.Success: LED lashes greenFailure: LED remains solid red2 / 4 U(2x)What is the diameter of the hole in the door?Remove battery cover and battery pack from interior assembly.Install 4 AA batteries in battery pack.Install interior assembly onto mounting plate.Make sure the door is open, and insert the battery pack.After a few seconds, the latch bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process, and it is crucial to lock operation.If the latch bolt does not move on its own, or if the Status LED indicates a door handing failure, make sure the cables are connected, the batteries are installed correctly, and attempt this procedure again.If the door handing process is still unsuccessful after a second attempt, perform the “Manual Door Handing” procedure on page 4.Locate screws for step 3C and keep them within reach. Install exterior keypad and mounting plate.AAABB CDBCDiameter is 21/8" (54 mm)Diameter is 11/2"(38 mm)or“D” is required for installation. Install “D” on “F”.“D” is not needed for installation. Discard “D”. Cable goes underneath latch. Support exterior assembly during mounting plate installation.Route cable through center hole, then push cable into bottom hole. Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (T). Remove key when inished and make sure the latch bolt is fully extended.Keep parallel to edge of door.Tighten screws evenly.aaccbbddMake sure turnpiece is in the vertical position.Note: Latch bolt will only retract half way.Make sure turnpiece shaft is rotated as shown. Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Do not install batteries until step 5.Ensure tight cable connection.Lay excess cable lat inside the bottom of the interior housing.alignLacbdactual sizeTbottom holeDDFFGTT (2x)TEM LLLK3Install the exterior keypad4Install the interior assembly5Install the batteries and perform the door handing processThis step will teach your lock the orientation of your door and is crucial to lock operation.
1xgreen3xredMastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 888 page at kwikset.com.Add the lock to your smart home systemInitiate the process to add the lock to your system at your smart home controller. Refer to your smart home system instructions for more information. When prompted by your smart home system to add the lock, press button “A” on the lock interior one time. The red LED will illuminate when the lock enters Add Mode. If successful, re-name the lock in your system (if applicable).If unsuccessful, follow your system's instructions to remove the lock from the controller and any other network, then press button “A” on the lock one time. Perform steps 6A6C again.If still unsuccessful, consult the Programming and Troubleshooting Guide on the SmartCode 888 page at kwikset.com.A B CD3 / 4Conirm that the code(s) added in previous step can unlock the door.Lock button lashes green once with one beep Lock button lashes three times with three beepsorMake sure the door is open. Press the Program button once.Install the interior cover. Secure the interior cover with three (3) screws. Note: To access the battery pack or back panel, slide up the window on the interior cover.Locking the Door Unlocking the Door Re-Key with SmartKeyEnter user code. A total of 30 user codes may be programmed.Press Lock button once.AA BB CWhat lights and sounds does the lock produce?DEach user code must be a unique code between 4 and 8 digits, depending on your smart home system.Programming was successful. Programming was unsuccessful.Make sure not to pause for more than 5 seconds during programming.Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user code positions are illed, delete a code to make room for this one.Press Lock button once.Enter user code.It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here.Programming Timeout During programming, if no button is pressed for ive seconds, the system will time out (indicated by three beeps and a red lashing lock button), and you will need to restart the procedure.actual sizeV button “A”Please allow time for the controller to add the lock.HRe-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.V (3x)M6789Add user codes (30 max)Install the interior coverTest the lock (review normal operation) and re-key the lock (if needed)
Alert Reason SolutionLock button lashes red once with one beep*.One incorrect code entered. Re-enter code.Lock button lashes red three times with three beeps*.No user code programmed.Program at least one user code.Programming timeout after ive seconds. Attempt programming procedure again.Unsuccessful programming.Lock button lashes red 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second keypad lockout.Lock button lashes red with fast beeping sound for three to four seconds.Low battery. Replace batteries.Lock button lashes green with continuous beeping sound for two seconds.Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.Factory ResetA factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.Manual Door HandingIf needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a di erent door.1. Remove battery pack.Status LED2. Press and HOLD the Program button while reinserting the battery pack.Release button once battery pack is installed. The status LED will lash red and green.3. Press the Program button once more. 4. The latch bolt will extend and retract to learn the orientation of the door. The Status LED will indicate success or failure.Success: LED lashes greenFailure: LED remains solid redIf the Status LED indicates a failure, see the online Programming and Troubleshooting Guide or call Technical Support.© 2016 Spectrum Brands, Inc.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode.5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Important SafeguardsIf unsuccessful: Make sure to enter the same valid code in steps 3 and 5. Test code: While the door is open, test the user code to make sure it no longer unlocks the door.If no button is pressed for ive seconds, the system will time out, and you will need to restart the procedure.Network InformationZWave System NotesThis product is a security enabled Z-wave Plus product and must be used with a Security Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and results may vary based on building construction and communication path.To assure interoperability, each ZWave product must pass a stringent conformance test to assure that it meets the ZWave standard for complete compliance with all other devices and controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers that their products will reliably perform with any other ZWave device. And, regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.ZWave Coniguration and Association Parameters are available on the SmartCode 888 page at www.kwikset.com.Removing the lock from the networkFollow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once.4 / 4SmartCode 888 at a Glance1. Press Program button once. 2. Press button “A” once. 1. Press Program button once. 2. Press button “A” once.1. Press Program button once. 2. Press button “A” once.Reference GuideStatus LEDThe Status LED blinks every 6 seconds to communicate whether the door is locked or unlocked. This feature is on by default.Blinking Green: UnlockedBlinking Amber: LockedBlinking Red: Low batterySolid Red: Unsuccessful door handing process. See online Programming and Troubleshooting Guide.Auto-LockAuto-lock automatically re-locks the door after unlocking. This feature is set to 30 seconds and is turned o by default.Turn Auto-Lock On/O Change Auto-Lock Time DelayTroubleshootingMute/Unmute AudioAudio is on by default.Deleting a single user codeNote: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the Programming and Troubleshooting Guide.Status LEDSystem AlertsExteriorKeypadLock buttonKeywaySmartKey tool holeBack panelProgram buttonStatus LEDTurnpiece shaftNote: When the cover is removed, the turnpiece shaft can be used to manually lock and unlock the door.Interior (cover removed)Button “A”A complete Programming and Troubleshooting Guide is available on the SmartCode 888 page at www.kwikset.com.3. Press button “34” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once. 3. Press button“90” once.4. Press button once that corresponds to desired time delay:“12” – 30 sec.“34” – 60 sec.“56” – 90 sec.“78” – 120 sec.“90” – 180 sec. 5. Press Lock button once.1. Press Program button once. 2. Press button “A” once.Turn Status LED On/O 3. Press button “12” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once.3. Press button “56” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once.1. Press Program button once. 2. Press Lock button once.3. Enter user code to be deleted. 4. Press Lock button once.5. Re-enter user code. 6. Press Lock button once.1. Remove battery pack.Status LED2. Press and HOLD the Program button while reinserting the battery pack.Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.3. Press the Program button once more. When the LED lashes green and you hear one beep, the lock has been reset.4. After a few seconds, the lock will initiate the door handing process, and the latch bolt will extend and retract to learn the orientation of the door.

Navigation menu