Spin Master Toys Far East 20418TX2G4 ARH XSM HyprRacrsProAst User Manual Layout 1
Spin Master Toys Far East Ltd. ARH XSM HyprRacrsProAst Layout 1
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1449498 |
| Application ID | 6XpZqUihy4g0KsnzyvYmgw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 138.94kB (1736747 bits) |
| Date Submitted | 2011-04-17 00:00:00 |
| Date Available | 2011-04-17 00:00:00 |
| Creation Date | 2011-03-23 16:14:50 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2011-03-23 16:14:50 |
| Document Title | Layout 1 |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | wckung |
12+ TM ® YRS EXPERT CHG/OFF/ON Switch INSTRUCTIONS Rollbar Red Charge Light Charge Port Green Power Light Directional Control Left/Right Interchangeable Rubber and Foam Tires for Various Terrains Throttle Trigger Variable Speed Dial Pull – Proportional Speed Push – Brake and Reverse SLOW FAST Trim Dial Hyper Actives™ Contents: • 1 x Hyper Actives™ • 4 x Rubber All Terrain Tires • 4 x Rubber Foam Indoor Tires • 1 x Pistol Grip Remote/Charger • 1 x Instruction Guide Charge Plug Rubber All Terrain Tires Remote/Charger INSTALLING/REPLACING THE BATTERIES 1. Open the battery door with a screwdriver (not included). 2. If used batteries are present, remove these batteries from the unit by pulling up on one end of each battery. 3. Install new batteries as shown in the polarity diagram (+/-) inside the battery compartment. 4. Replace battery door securely. 5. Check your local laws and regulations for correct recycling and/or battery disposal. Battery Compartment Cover 6x 1.5V AA Alkaline Batteries Battery Compartment BATTERY SAFETY INFORMATION • Remote/charger requires 6 x 1.5V AA alkaline batteries (not included). • Batteries are small objects. • Replacement of batteries must be done by adults. • Follow the polarity (+/-) diagram in the battery compartment. • Promptly remove dead batteries from the toy. • Dispose of used batteries properly. • Remove batteries for prolonged storage. • Only batteries of the same or equivalent type as recommended are to be used. • DO NOT incinerate used batteries. • DO NOT dispose of batteries in fire, as batteries may explode or leak. • DO NOT mix old and new batteries. • DO NOT mix different types of batteries, i.e.: alkaline/standard (carbon-zinc) or rechargeable batteries. • DO NOT use rechargeable batteries. • DO NOT recharge nonrechargeable batteries. • DO NOT short-circuit the supply terminals. • DO NOT store your car or controller near heat or in direct sunlight. HOW TO CHARGE YOUR HYPER ACTIVES™ 1. Turn vehicle OFF. 2. Turn remote/charger OFF. 3. Remove charge plug from storage base. 4. Remove charge cable from bottom storage groove. 5. Remove vehicle charge port cover. 6. Carefully insert the charge plug all the way into the vehicle’s charge port. 7. Set the remote/charger switch to CHG. 8. The red charging light will turn on and charging will begin when it starts to flash. After 30 to 50 minutes the charging will be complete and the red charge light and green power light will both start to flash. 9. When charging is complete, set the charge switch to OFF. 10. Remove charge plug from the vehicle charge port. 11. Replace vehicle charge port cover. 12. Store charge plug cable and charge plug in remote/ charger base. CHG OFF ON CHG OFF ON 10 NOTE: 1. If the charge light and power light are flashing alternatively while charging, there may be a bad cable connection. Check that cable and plug are connected correctly and repeat charging steps 1 to 6. 2. The remote control will automatically shut off after idling for about CHG OFF ON 11 12 5 minutes. To reactivate turn off and on. 3. When the remote control is in either ON status or CHARGE status and the green power light is flashing, it means that the battery level is low and the batteries need to be replaced. USING THE REMOTE/CHARGER Forward/Reverse, Left/Right. 1. Turn vehicle ON. 2. Turn remote/charger ON. 3. Pulling the throttle trigger back moves the vehicle forward. Pushing the throttle trigger forward, brakes then reverses the vehicle. 4. To move the vehicle to the right turn the directional control to the right. 5. To move the vehicle to the left turn the directional control to the left. Right Forward CHG OFF ON Reverse Left VEHICLE TRIM ADJUSTMENT If the vehicle is not driving straight when you have the directional control wheel in the forward position, use the trim dial to correct the problem. 1. If the vehicle turns to the right, slowly turn the trim dial to the left until the vehicle drives straight. 2. If the vehicle turns to the left, slowly turn the trim knob to the right until the vehicle drives straight. VARIABLE SPEED DIAL Moving the variable speed dial to the right will limit the throttle travel decreasing the amount of speed available. Moving the dial to the left will activate full throttle and maximum speed. SLOW FAST CHANGING TIRES WHEN FINISHED PLAYING Before using your Hyper Actives™ outdoors, carefully remove the rubber foam indoor tires and replace them with the rubber all terrain outdoor tires! Turn vehicle OFF. SELF-RIGHTING ROLLBAR Turn remote/charger OFF. CHG OFF ON A fast, quick turn will cause the vehicle to roll over and the self-righting roll bar will return the vehicle onto its wheels! TROUBLESHOOTING GUIDE PROBLEM SOLUTION CAUSE Vehicle is slow or will not move. 1. Batteries in the controller need to be replaced if green power light is flashing. 2. Vehicle is out of range of controller. 3. There is hair or debris stuck in the wheels or wheel axles. 4. Batteries are installed incorrectly. 5. Improper surface for vehicle. 6. Remote not aimed at vehicle or objects interfering with signal. 7. Remote was inactive for 30 seconds or more and turned itself off to preserve your batteries. 1. Replace batteries in the remote with new, fresh batteries. 2. Move closer to the vehicle. 3. With the vehicle and remote turned off, have an adult carefully remove the hair or debris from the wheels or wheel axles. Remove debris by blowing gently on the wheel assembly area located on the bottom of the vehicle. 4. With the vehicle and remote turned off, have an adult check that the batteries are installed correctly in the remote. 5. Examples of poor play surfaces are thick grass, sand or pebbly areas. Examples of good play surfaces are tiles, concrete or asphalt. 6. Point remote IR at the vehicle. Ensure there are no objects blocking the controller “line of sight” to the vehicle. 7. Press the ON/OFF button. Vehicle does not drive in a straight line. Vehicle requires wheel alignment. Refer to Trim Adjustment guide above. My vehicle and/or remote is dirty. 1. Inappropriate driving surface. 2. Dirty hands. Ensure the remote and vehicle are off. Have an adult remove the batteries first and replace the battery cover. Slightly dampen a clean cloth in water and wipe toy clean. DO NOT IMMERSE IN WATER and DO NOT USE ANY CHEMICALS. Let the toy completely dry before putting batteries back into clean, dry battery compartment. Vehicle is not responding or driving on it’s own. 1. Using another vehicle remote/ charger of the same frequency. 2. Infrared interference from another source. 1. Only use the remote/charger supplied with this vehicle. 2. Do not operate vehicle around devices that emit other infrared signals. NOTE: If normal function of the product is disturbed or interrupted, strong electro-magnetic interference may be causing the issue. To reset product, turn it completely off, then turn it back on. If normal operation does not resume, move the product to another location and try again. To ensure normal performance, change the batteries, as low batteries may not allow full function. This deviceThis complies withcomplies Part 15 ofwith the FCC subject to the following twoto conditions: (1) This may not(1) cause and harmful (2) This device must accept product Partrules. 15 ofOperation the FCCisrules. Operation is subject the following twodevice conditions: Thisharmful device interference, may not cause interference, andany (2) interference This devicereceived, must including interference may cause undesirable operation. This equipment hascause been tested and found to comply with the limitshas for Class digital and devices pursuant to Part 15the of the FCCfor rules. These limits are accept any that interference received, including interference that may undesirable operation. This equipment beenBtested found to comply with limits Class B digital designed to provide reasonable protection against harmful interference to radio communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be guarantee that devices pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference to radio communications. This equipmentno generates, interference occur.radio if notfrequency installed and used and, in accordance with the instructions, may cause harmful radiocause communications. If this toy does causecommunication. interference to radio television reception uses and will cannot radiate energy if not installed and used in accordance with theinterference instruction,tomay harmful interference to radio If thisortoy does cause (you can check this by turning the toy reception off and on (you whilecan listening thebyinterference), or more of the following measures may be useful: one • Reorient or relocate the receiving antenna • Increase the separation interference to radio or television checkfor this turning the one toy off and on while listening for the interference), or more of the following measures may be useful: between the toy the radio or the TV • antenna Consult the dealer or the an experienced for help. NOTE:Changes, modifications to this unit, including not limited replacement of any • Reorient or and relocate the receiving • Increase separation TV-radio betweentechnician the toy and the radio or the TV •adjustments Consult theordealer or an experienced TV-radiobut technician forto,help. transmitter component (crystal, semiconductor, etc.) could a violation FCClimited rules under part 15 and/or 95 and must be expressly approved by semiconductor, Spin Master Ltd. or they could voidinthe user’s authority to NOTE: Changes, adjustments or modifications to thisresult unit,inincluding butofnot to, replacement of any transmitter component (crystal, etc) could result a violation of operate the equipment. FCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd. or they could void the user’s authority to operate the equipment. CANADIAN Class B statement: This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. Your Hyper Actives™ is equipped with a Lithium Polymer battery. SPECIAL LIPO BATTERY INSTRUCTIONS: - Never charge battery unattended. - Charge battery in isolated area. Keep away from flammable materials. - Do not expose to direct sunlight. - There is a risk of the batteries exploding, overheating, or igniting. Do not disassemble, modify heat, or short-circuit the batteries. Do not place them in fires or leave them in hot places. - Do not drop or subject to strong impacts. - Do not allow the batteries to get wet. - Only charge the batteries with the specified Spin Master™ battery charger. - Only use the batteries in the device specified by Spin Master™. - Carefully read the instruction guide, and use the batteries correctly. - In the unlikely event of leakage or explosion use sand or a chemical fire extinguisher for the battery. - Batteries must be recycled or disposed of properly. Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221, USA Spin Master Toys Far East Limited, Rm #1113, 11/F, Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HK North American Consumer Information Phone: 1-800-622-8339 Email: customercare@spinmaster.com www.spinmaster.com PRODUCT BATTERY REMOVAL INSTRUCTIONS: Internal battery is factory installed, product disassembly and battery removal must be performed by an adult. Do not puncture, cut, tear, compress or deform product during disassembly. Ensure product is turned off, then use a screw driver to remove all screws. Separate product body halves to expose internal electronics. When battery is visible in its entirety use scissors to cut a single battery wire, immediately wrap the cut wire end with tape to isolate it, repeat until all battery wires are cut and isolated, and the battery is free from the rest of the product. Dispose of battery in accordance with your local battery recycling or disposal laws. NOTE: Opening of product and/or removal of battery will render product inoperative and voids manufacturer warranties, dispose of remaining product components in accordance with local laws. Air Hogs®, related trademarks & © 2011 Spin Master Ltd. All rights reserved. This product conforms to safety requirements of ASTM F-963 & CHPA. • Please retain this information for future reference. • Please remove all packaging materials before giving to children. • An adult should periodically check this toy to ensure no damage or hazards exist, if so, remove from use. • Children should be supervised during play. • Keep addresses and phone numbers for future reference. • The item inside this package may vary from the photographs and/or illustrations. MADE IN CHINA. 20043334, 20043335, 20049415, 20049426 T20418_0001_20043334_NEN_IS_R1 REV 0 TM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Create Date : 2011:03:23 16:14:50+08:00 Modify Date : 2011:03:23 16:14:50+08:00 Metadata Date : 2011:03:23 16:14:36+08:00 Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:F0AF0A732555E0118DB4AD052A672EF4 Instance ID : uuid:77e28bb0-764e-404f-8244-dab9f203387c Derived From Instance ID : uuid:d69ec540-53ab-415c-9c4c-0f7bdf2b55c6 Derived From Document ID : uuid:a92104d1-dfe6-534f-9442-11d1e4fd611a Format : application/postscript Title : Layout 1 Creator : wckung Page Count : 2 Author : wckungEXIF Metadata provided by EXIF.tools