Spot STAMP DTS Developer Board User Manual Stamp User s Manual

Download:
Mirror Download [FCC.gov]
Document ID	879028
Application ID	VsaU+16SQrYjz2TynGJO1g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.2kB (127459 bits)
Date Submitted	2007-12-13 00:00:00
Date Available	2007-12-21 00:00:00
Creation Date	2006-10-04 11:52:40
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-02-02 10:05:52
Document Title	Microsoft Word - Stamp User's Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	eric blanchard

2.4 GHz Stamp User’s Manual
Part Number 9100-0160-01
Revision 1.0
Date: October 4, 2006
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
1/7
Table of Contents
1.
2.4 GHz Stamp Product Description…………………………………………
2.
Typical Integration……………………………………………………………
3.
Product Specifications………………………………………………………...
3.1 Specifications………………………………………………………………
3.2 Pin Diagram………………………………………………………………..
3.3 Pin Descriptions…………………………………………………………….
Air Interface…………………………………………………………………....
4.1 Frequency…………………………………………………………………....
4.2 Power……………………………………………………………………….
4.3 Timing………………………………………………………………………
4.
5.
Serial User Interface………………………………………………………….
5.1 Message Protocol…………………………………………………………...
5.2 Tips………………………………………………………….........................
5.3 Timing………………………………………………………….....................
5.4 Digital I/O…………………………………………………………..............
6.
Mounting Guidelines………………………………………………………….
7.
Power Supply Requirements………………………………………………….
8.
Environmental Specifications…………………………………………………
9.
Regulatory Approvals…………………………………………………………
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
2/7
1.
2.4 GHz Stamp Product Description
To be completed
2.
Typical Integration
Below is a block diagram of how a normal system using a 2.4 GHz Stamp would be
designed.
3.
3.1
TBC
Product Specifications
Specifications
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
3/7
3.2
3.3
Pin
10
11
12
13
14
Pin Diagram
Pin Descriptions
Pin Name Electrical Spec
GND
Reset
DO NOT CONNECT
VRF
3.3V +/-5%
GND
VDIG
3.3V +/-5%
RF RX
3.3V TTL Output
Logic 0: <0.6V
Logic 1: >0.8*Vdig
Test In
DO NOT CONNECT
NC
GND
NC
NC
RF TX
3.3V TTL Input
Logic 0: <0.6V
Logic 1: >0.8*Vdig
GND
GND
Axonn LLC
Note
Tie directly to host ground plane.
For use with serial programming
Powers the 2.4 GHz transceiver
Powers digital circuitry
Data Input
To be transmitted over 2.4 GHz radio
2400 baud
For use with serial programming
Data output
Information received over 2.4 GHz radio
2400 Baud
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
4/7
Approximate Current Consumption (through Vdig and Vrf combined):
Maximum: 25mA
Sleep mode: 1-2µA
4.
Air Interface
TBC
4.1 Frequency
TBC
4.2 Power
TBC
4.3 Timing
TBC
5.
Serial User Interface
TBC
5.1 Message Protocol
TBC
5.2 Tips
TBC
5.3 Timing
TBC
5.4 Digital I/O
TBC
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
5/7
6.
Mounting Guidelines
The figure below shows the recommended footprint for mounting the Stamp on its host
board.
7.
TBC
Power Supply Requirements
8.
TBC
Environmental Specifications
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
6/7
9.
Regulatory Approvals
FCC ID: L2V-STAMP
IC:3989A-STAMP
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Axonn LLC
Stamp User’s Guide-Document #9100-0160-01 Ver 1.0
7/7
The FCC requires the following notification for the device in compliance with 47CFR
15.105 for this Class B digital device. Full product test reports are available from Axonn
upon request.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential environment. This equipment ge nerates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
WARNING: Changes or modifications not expressly approved by Axonn may render the
device non-compliant to FCC and other regulatory body standards for operation and may
void the user’s authority to operate the equipment.
Accessory items that can be readily obtained from multiple retail outlets are not considered
to be special accessories and are not to be marketed with the equipment. Only those
accessory items provided by Axonn have been tested to ensure operation consistent with the
regulatory standards that the device is required to perform.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This ClassB digital apparatus complies with Canadian ICES-003.
This device will operate in accordance to the standards set forth by the CE Mark Directives
and standards R&TTE: ( EN 300 328), RFI: (EN61000-4-3:1996
+ A1:1998 + A2:2000), ESD: (EN61000-4-2: 1995 + A1:1998)
NOTICE: This equipment complies with the FCC RF Exposure Limits. A minimum of 20
centimeters (8 inches) separation between the device and the user and all other persons
should be maintained.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2007:02:02 10:05:52-05:00
Create Date                     : 2006:10:04 11:52:40-05:00
Author                          : eric blanchard
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f52cc46e-1f9c-4976-9fd8-5ad5b2b436b5
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2006:10:04 11:58:54-05:00
Document ID                     : uuid:d006f849-ca7e-44cc-b6d1-ddceae6116a8
Format                          : application/pdf
Creator                         : eric blanchard
Title                           : Microsoft Word - Stamp User's Manual

EXIF Metadata provided by EXIF.tools