Stack On PC-1702-RFID RFID Reader User Manual 40720 1702 A5

Stack-On Products Company RFID Reader 40720 1702 A5

User manual.pdf

40720-1702 116InstructionsPC-1702-RFIDTools Required: DrillFlat Head Screwdriver10 mm Wrench 3/16” (5 mm) drill bit for drilling into woodHardware Included: (2) M6 x 20 mm (3/4” long) Screws(2) Washers(2) Plastic anchors ®Your Electronic Combination:Serial #:IMPORTANTNOTE: You can store your Key #, Serial # and Combination on Stack-On’s SECURE website – stackon.com under Customer Service.Storing your Key # or Combination will provide instant access to this important information should you ever lose your keys or your combination. Only you will have access to this information.• Record the serial number from the tag on the back of the case.• Record your combination number.• Keep keys and your combination in a secure place away from children.• DO NOT STORE KEYS, RFID DEVICES OR YOUR COMBINATION IN THE CASE.CONTROL FEATURES1. Key lock2. Combination buttons3. Reset button (inside case)4. Battery Compartment (inside case)5. RFID Sensor 5REMOVE KEY FCC COMPLIANCENOTE: This equipment has been tested and found to comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provent reasonable protecon against harmful itererence in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occor in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, whitch can be determined by turning the equipment off and on, that user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separaon between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.Cauon: Modificaons not authorized by the manufacturer may void users authority to operate this device.CAN ICES-3 (B)/NMB-3(B).Battery Disposal Please dispose of the used batteries per municipal or provincial law.
Tools Required: DrillFlat Head Screwdriver10 mm Wrench 3/16” (5 mm) drill bit for drilling into woodGETTING STARTED INSTALLING THE BATTERIESWhen you first receive your case you will need to open the cover with the key in order to install the baeries. Baeries are included and are located inside the case.Pull the foam upward and away from the baery compartment. Remove the baery compartment by pushing the tab and pulling the compartment out as shown. Install (4) AAA alkaline baeries which are included. Reinstall the compartment by hooking the back end in place and snapping shut. CAUTION: Be careful not to pinch any wires while reinstalling the baery compartment.Red light will flash and beep once (if the sound is turned on) if baeries are installed correctly.NOTE: If the baeries are low the lights will flash red when the buons are pushed. Replace the 4 AAA baeries with new alkaline baeries as described above. NOTE: The key has also been provided if you lose or forget your security code or the baeries run low. If you lose your key, or any of your RFID devices, you may purchase a replacement by referencing the serial number located on the back of the case. See secon regarding replacement RFID device/keys for further informaon.To open the case, insert key into the lock and turn clockwise unl the cover automacally opens. NOTE: You must turn the key back to the locked posion before you are able to close and lock the cover.NOTE: Do not mix old and new baeries. Do not mix alkaline, standard or rechargeable baeries.OPENOPENBaery Carriage4 - AAA baeriesREMOVE KEY 40720-1702 216 LOW BATTERY WARNING
Hold RFID device approximately ¼” over the over RFID buon . Two “beeps” will sound (if the sound is turned on) and the panel will flash green twice and open.If RFID is not programmed, the Red light will flash and beep 3 mes (if the sound is turned on).Baery Carriage4 - AAA baeriesUSING THE RADIO FREQUENCY IDENTIFICATION DEVICES (RFID) Press the Reset Buon (3) located inside the case. Two “beeps” will sound (if the sound is turned on) and panel will flash blue twice. You will have 5 seconds to begin programming a RFID device or you will have to start over.If you do not program the RFID device (card, fob or scker), the RFID, Red light will flash and beep 3 mes.Center and place your access card, key fob, or scker on the RFID buon as shown in FIGURE 1.Two “beeps” will sound (if the sound is turned on) and panel will flash green twice if the device is recorded. Press the reset buon to confirm recorded devices. Four “beeps” will sound (if the sound is turned on) and panel will flash blue four mes if device is recorded. Repeat above steps to record addional RFID devices. NOTE: Recording RFID devices does not replace or remove other prerecorded devices, or combinaons.Only 5 RFID devices can be recorded.If an aempt is made to record a 6th device the case will beep 3 mes and the red light will flash 3 mes.OPENING THE CASE USING RFIDIf an invalid RFID device is scanned 3 mes the case will beep 5 mes (if the sound is turned on) and the red light will flash 5 mes resulng in the case being automacally locked out for 60 seconds before you can scan your device again. The case will beep one me (if the sound is turned on) and the green light will flash once when the lockout period is over.If an invalid RFID device is scanned 1 addional me, the case will beep 5 mes (if the sound is turned on) and the red light will flash 5 mes resulng in the case being automacally locked out for 5 minutes before the the scan can be tried again. The case will beep one me (if the sound is turned on) and the green light will flash once when the lockout period is over. The case may sll be opened using thesupplied Key to override failed RFID scans.To close the case, push the lid closed unl locked.FIGURE 1CARDSTICKER ON BACK 40720-1702 316
• For security you must program your own combinaon aer opening the case. • Record your new combinaon on this form or store your combinaon on our secure website at stackon.com under Customer Service. If you write down your combinaon you must keep this informaon in a secure place, away from children, not inside the case.USING THEELECTRONIC COMBINATIONEnter your combinaon using the buons. The buons will light up green and there will be one "beep"(if the sound is turned on) for every entry. If you entered the correct combinaon, the buons will flash green twice, with two beeps and the door will open. If the combinaon is incorrect the case will beep 3 mes (if the sound is turned on) and the red light will flash 3 mes. NOTE: You will have 2 seconds between individual entries before the case assumes you have entered your complete combinaon.If an incorrect security code is entered 3 mes the case will beep 5 mes (if the sound is turned on) and the red light will flash 5 mes resulng in the case being automacally locked out for 60 seconds before you can try your code again. The case will beep one me (if the sound is turned on) and the green light will flash once when the lockout period is over.If the incorrect security code is entered 1 addional me the case will beep 5 mes (if the sound is turned on) and the red light will flash 5 mes resulng in the case being automacally locked out for 5 minutes before the code can be tried again. The case will beep one me (if the sound is turned on) and the green light will flash once when the lockout period is over.The case may sll be opened using thesupplied Key to override failed security code.To close the case, push the lid closed unl locked.OPENING THE CASE USING ELECTRONIC COMBINATION1.2.3.Example: (RIGHT) - (LEFT) - (CENTER) - (LEFT) - (RIGHT)Press the Reset Buon (3) located inside the case. Two “beeps” will sound (if the sound is turned on) and all 3 buons will flash blue twice. You will have 5 seconds to begin entering your combinaon or you will have to start over.Enter your own 3-8 buon combinaon by pressing any combinaon of the 3 buons. For Each combinaon entry a “beep” will sound (if the sound is turned on) and all the buons will light up green. If you delay more than 5 seconds between entries there will be 3 beeps (if the sound is turned on) and 3 red flashes and you will have to start over from step 1. Aer you have finished entering your combinaon, you will have 5 seconds to press the Reset Buon to record your new combinaon or you will have to start over from step 1.When you press the Reset Buon to record your new combinaon, there will be two “beeps” (if the sound is turned on) and all 3 buons flash blue twice, indicang your new combinaon has been recorded.If the combinaon you entered does not acvate the locking mechanism, you will need to go back to step 1 in this secon.To confirm your combinaon was entered correctly, turn the key to the locked posion (the lid may remain open) and follow the instrucons in the “OPENING THE CASE USING YOUR COMBINATION” secon.4.40720-1702 416
SECURING THE CASE WITH THE CABLEFor opmal performance while on the go, the case should be installed in an isolated, dry and secure area.NOTE: This case can be secured with a cable that is aached to a fixed object. Failure to to do so will compromise the safety and security of the case.To secure the case to a fixed object, loop the cable around the object and place the cable’s small end into the notch on the side of the case. Tip the cable end down while inserng in the notch. Locking the case will secure the cable end inside the case.THE CASE SHOULD ALWAYS BE KEPT OUT OF THE REACH OF CHILDREN.SECURING THE CASE WITH HARDWARESecure case using screws and washers as shown below. NOTE: This case must be mounted to a permanent shelf. Failure to do so will compromise the safety and security of the case.SELECTING A LOCATIONThe case is to be mounted to a permanent shelf. For opmal safety and security, the case should be installed in an isolated, dry and secure area.THE CASE SHOULD ALWAYS BE KEPT OUT OF THE REACH OF CHILDREN.40720-1702 516
TURNING THE KEYPAD SOUND OFF/ONYour case comes with the "Beep" sound turned on. You can turn off the "Beep" sound of the keypad by pressing RFID buon and holding for 3 seconds unl the panel flashes green then purple.To turn the "Beep" sound on, press the RFID buon and hold for 3 seconds unl the panel flashes green then purple.CLEARING ALL CODESClearing the codes will erase the signature of the programmed RFID devices and the programmed electronic combinaon. Locate the reset buon on the inside of the case and press and hold unl the green light flashes and beeps 10 mes (if the sound is turned on). NOTE: Failure to follow instrucons will not erase the codes.All recorded devices and combinaon will be erased. You will need to reprogram all devices and the combinaon described in the Programming Secons of this instrucon sheet.STACK-ON® PRODUCTS CO.P.O. BOX 489, WAUCONDA, IL 60084IMPORTANTKeep keys, RFID devices and your combinaon number is a secure place, away for children. Keep this record of your serial number and combinaon in a secure place separate from your case. To order a replacement RFID device, or key set, follow the instrucons on the aached form.NOTE: This unit is not an approved California Department of Jusce firearm safety device.40720-1702 616
RFID Device or Key Request“This is not a Registration Form”Verification of ownership is required in order to receive replacement RFID device or key for your security product. In order to receive a replacement RFID device or key to your security product: 1. Complete the following form and send to Stack-On Products. 2. Send a copy of your valid driver’s license along with the form. 3. Send a copy of the receipt showing the original purchase. 4. Security product owner must sign form. 5. Owner’s signature must be notarized.6. Send $10.00 for replacement key/RFID device. Personal Check, MasterCard, or Visa accepted.7. Send completed information to: Stack-On® Products Company 1360 N. Old Rand Road P.O. box 489 Wauconda, IL 60084 Serial Number___________________Key Number (if applicable) _________ RFID device_________ Unit Dimensions________________________________________Unit Description___________________________________________________________Owner’s Name ____________________________________ Date Purchased___/___/____ Owner’s Address ___________________________ Unit or Apt Number _________________ City ___________________________ State _______________ Zip Code________________ Telephone Number: (____)___________________ Fax Number: (____)___________________ Owner’s Email Address: ________________________________________________________ Owner’s Signature __________________________ Notary Signature________________ Notary Commission Expires: _____/_____/_____ Notary Stamp SERVICE REQUESTEDKey / RFID Device Replacement: Yes No $10.00 charge for this service Credit Card Information (Please circle one): MasterCard VisaExpiration Date: ___/___/___ Card Number:______________________________________ Credit Card Identification Number (Located on back of card, last 3 digits on signature strip)_________ NOTE: You can store your Key #, Serial # and Combination on Stack-On’s SECURE website – stackon.com under Customer Service. Storing your Key # or Combination will provide instant access to this important information should you ever lose your keys or your combination. Only you will have access to this information.®40720-1702 716
R LIMITED ONE YEAR WARRANTYSTEEL CABINETS AND SECURITY CASESStack-On Products Co. (“Stack-On”) Steel Cabinets and Security Cases, are warranted to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase by a consumer. This warranty extends to the initial consumer only.If you believe there is a defect in material or workmanship in your Steel Cabinet or Security Case, during the one-year warranty period, please contact our customer service department, by regular mail or email at the address listed below, and include with your correspondence proof of purchase information and the model number of the product.Stack-On® Products Company1360 North Old Rand RoadWauconda, IL 60084customerservice@stack-on.comIf Stack-On is properly notified during the one-year warranty period and, after inspection confirms there is a defect, Stack-On will, at its sole option, provide repair parts or exchange the product at no charge, or refund the purchase price of the product.THIS WARRANTY DOES NOT COVER ANY PRODUCT, OR ANY PART OF ANY PRODUCT, WHICH HAS BEEN SUBJECT TO EXCESSIVE USE, ACCIDENT, NEGLIGENCE, ABUSE OR MISUSE, INCORRECT MAINTENANCE, ALTERATION OR REPAIR BY ANYONE OTHER THAN STACK-ON. IN ADDITION, THIS WARRANTY DOES NOT COVER ANY ACCESSORIES OR PARTS USED WITH OR IN THE PRODUCT, WHICH ARE NOT INCLUDED WITH THE ORIGINAL PURCHASE.THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED. STACK-ON SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES. STACK-ON NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT, ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF STACK-ON’S STEEL CABINET OR SECURITY CASE.STACK-ON WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO THE INITIAL CONSUMER FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES ARISING OUT OF THE PURCHASE OR USE OF ANY STACK-ON STEEL CABINET OR SECURITY CASE.STACK-ON’S LIABILITY FOR ANY BREACH OF THIS WARRANTY SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT, AS DESCRIBED ABOVE, OR A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.IN NO EVENT SHALL STACK-ON’S OBLIGATION UNDER THIS WARRANTY EXCEED THE PRICE OF THE PRODUCT.THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.40720-1702 816

Navigation menu