Standard Industrie COFROUTCA ROUTER FOR AIRCHOC WIRELESS APPLICATION User Manual NOTCOFROUT US G1

Standard Industrie ROUTER FOR AIRCHOC WIRELESS APPLICATION NOTCOFROUT US G1

User Manual

NOTCOFROUT-US.doc 1 December 6th, 2012 USER MANUAL Revision Level: G1 NOTCOFROUT-US Date: December 6th, 2012 Produced on: December 6th, 2012 By: DESIGN OFFICE Checked on: By: BOISLEUX.M Signature: HEAD OFFICE- Standard Industrie : 139-141 rue du Luxembourg-BP50207 59054 ROUBAIX CEDEX 1- FRANCE +33 (0)3 20 28 32 32 / @ : info@standard-industrie.com
NOTCOFROUT-US.doc 2 December 6th, 2012 CONTENTS 1 Principle of Airchoc Wireless page 3 2 Router presentation page 4 2-2 General characteristics page 4 2-21 Electrical characteristics page 4 2-22 Explanation of the symbol on the label page 4 2-23 Environmental characteristics: page 4 2-24 Additional exterior characteristics page 4 3 Network with router page 4 3-1 Principle page 5 4 General information Page 6
NOTCOFROUT-US.doc 3 December 6th, 2012 1- Principle of Airchoc Wireless
NOTCOFROUT-US.doc 4 December 6th, 2012 2- ROUTER PRESENTATION 2-2. General Characteristics 2-21. Electrical Characteristics - Power supply : 120V ac - 60Hz - Max power : 1W 2-22. Explanation of the symbol on the label : After power has been removed and the overcurrent condition eliminated, the circuit is restored to normal operating condition This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2-23. Environmental characteristics: Material : Flame Retardant ABS (UL94-V0) - Service temperature: - Humidity : - Max altitude - Pollution degree Minimum: -20°C Maximum: +70°C no more than 80% e.g up to 2000 m 2 Attention : it is forbidden to clean the control panel to the high-pressure water. The protection is impaired if equipment is used in a manner not specified by the manufacturer. - Electric cable used for connecting have to be in accordance with the standard IEC 60320-1, 60227 2-24. Additional Exterior Characteristics This router includes -RF transmission module - 915 MHz as per IEEE 802.15.4-2003/2006 standard Number of address of the router which will be visualized in the network There is no risk of power to hit the metal part of the antenna output if the router is powered. This router is Class II The router is protected by a resettable fuse 0,16A and no dismantling of the box is called. Wireless external antenna Standard Industrie reference : COFANTENNA Characteristics Frequency [MHz] : 868-928 Gain [dBi] : 3.0 Impedance [Nom] : 50Ω VSWR : ≤2.0 Polarization : Vertical Electrical length : ¼, dipole Radiation : Omni
NOTCOFROUT-US.doc 5 December 6th, 2012 3) NETWORK WITH ROUTER FOR SYSTEME WIRELESS 3-1) Principle In the case of transmission problems between the control panel and the receivers, routers can be installed. While positioning the routers on high points, and provide a power supply. The control panel communicates with the router through the antenna. The router relays the information to the receiver Antenna Control panel Router Receiver Control panel Power
NOTCOFROUT-US.doc 6 December 6th, 2012 4 – General Information Changes or modifications not expressly approved by Standard Industrie could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC’s radiation exposure limits set forth for an uncontrolled environment under the following conditions : 1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and user’s/nearby person’s body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu