Star Solutions P800-1 iCell CDMA 1X BTS Module - 800 MHz User Manual Pico BTS
Star Solutions International Inc iCell CDMA 1X BTS Module - 800 MHz Pico BTS
manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 528144 |
| Application ID | 48Z73rRqU1aUDS1AIzqlOg== |
| Document Description | manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 121.67kB (1520860 bits) |
| Date Submitted | 2005-03-31 00:00:00 |
| Date Available | 2005-03-31 00:00:00 |
| Creation Date | 2005-03-28 15:58:16 |
| Producing Software | ScanSoft PDF Create! 2 |
| Document Lastmod | 2005-03-28 15:58:16 |
| Document Title | Microsoft Word - User Manual Pico BTS.doc |
| Document Creator | Microsoft Word - User Manual Pico BTS.doc |
| Document Author: | perrella |
MovingMedia® 2000 iCell CDMA2000 1X Pico BTS BASIC INSTALLATION GUIDE RELEASE 4.5 DRAFT 0.1 PART NUMBER NXX0306XXX MovingMedia 2000 iCell Pico BTS Installation Guide Page 1 of 16 Copyright © 2004 UTStarcom Incorporated. All rights reserved. Copyright © 2004, UTStarcom, Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior written permission from UTStarcom, Inc. UTStarcom, Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of UTStarcom, Inc. to provide notification of such revision or change. UTStarcom, Inc. provides this documentation without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. UTStarcom may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. UNITED STATES GOVERNMENT LEGENDS: If you are a United States government agency, then this documentation and the software described herein are provided to you subject to the following: United States Government Legend: All technical data and computer software is commercial in nature and developed solely at private expense. Software is delivered as Commercial Computer Software as defined in DFARS 252.227-7014 (June 1995) or as a commercial item as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in UTStarcom's standard commercial license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (November 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide. UTStarcom, the UTStarcom logo and MovingMedia 2000 are registered trademarks of UTStarcom, Inc. and its subsidiaries. Other brand and product names may be registered trademarks or trademarks of their respective holders. Regulatory This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Where appropriate, the use of the equipment is subject to the following conditions: CAUTION! Unauthorized modifications or changes not expressly approved by UTStarcom could void compliance with regulatory rules, and thereby your authority to use this equipment. WARNING (EMI) - United States FCC Information - This equipment has been tested and found to comply with the limits pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician To comply with Maximum Permissible Exposure (MPE) requirements, the maximum composite output from the antenna cannot exceed 1.26 Watts EIRP and the antenna must be permanently installed in a fixed location that provides at least 13 cm of separation from all persons. MovingMedia 2000 iCell Pico BTS Installation Guide Page 2 of 16 1 PREFACE 1.1 Objective This document provides installation and configuration instructions for setting up an iCellCDMA2000 1X system. It covers physical installation, software installation for the various iCell components (sBSC and BTS), configuration, and initial system operation. 1.2 Organization The major sections of this guide are as follows: Table 1-1: Organization Table Chapter Title Description Chapter 1 Preface Introduction to the Installation Guide. Chapter 2 iCell System Description Describes the System components Chapter 3 BTS Physical Installation Provides mechanical installation and wiring instructions. MovingMedia 2000 iCell Pico BTS Installation Guide Page 3 of 16 1.3 Reference Documents The following table summarizes the applicable reference documents. Table 1-2: Reference Documents Ref. Title iCell CDMA2000 1X Alarms and Statistics iCell CDMA2000 1X Configuration Guide Number 1.4 Acronyms and Abbreviations The following table summarizes the acronyms and abbreviations used throughout the document. Table 1 -3: Acronyms and Abbreviations 1PPS One Pulse Per Second AAA Authentication, Authorization, and Accounting function Abis Protocol interface between sBSC and BTS ASN.1 The language used to define the MIB of the NE EM Element Manager GPS Global Positioning System HLR Home Location Register sBSC iCell Base Station Controller BTS iCell Base Station Transceiver Subsystem iMB iCell Main Board IOS Inter-Operability Standard; A-Interface between sBSC and MSC IP Internet Protocol iPA iCell Power Amplifier MIB Management Information Base MS Mobile Station (phone) MSC Mobile Switching Center NE Network Element or agent NOC Network Operations Center OID Object Identifier OMC Operations & Maintenance Center PA Power Amplifier MovingMedia 2000 iCell Pico BTS Installation Guide Page 4 of 16 PDSN PSTN RF Packet Data Serving Node Public Switch Telephone Network Radio Frequency Short Message Service Center SMSC SNMP SNTP TBD TCP Simple Network Management Protocol Simple Network Timing Protocol To Be Defined Transmission Control Protocol Time Of Day TOD MovingMedia 2000 iCell Pico BTS Installation Guide Page 5 of 16 2 iCell SYSTEM DESCRIPTION This chapter provides an iCell system description. 2.1 Introduction The iCell is an IP-based solution for CDMA2000 1X radio access networks. The iCell system provides the overall functionality of a CDMA2000 1X Base station transceiver subsystem (BTS) and soft base station controller (sBSC), providing an IP over Ethernet interface to the core network. Figure 2-1 shows the system architecture. sBSC PDSN MSC Pico BTS Managed IP Network IMG Figure 2-1: iCell System Block Diagram MovingMedia 2000 iCell Pico BTS Installation Guide Page 6 of 16 2.2 System Components The main iCell system network components are explained in this section. 2.2.1 BTS The BTS is the iCell Base Station Transceiver Subsystem. There can be several BTS units per sBSC. The BTS is the radio transmitter/receiver that maintains communication with Mobile phones. It can be configured as Omni, two sectors or 3 sectors. The BTS is connected through a Fast Ethernet Switch to the sBSC. Normally in an enterprise installation, the first BTS unit is connected to the GPS receiver and serves as an SNTP server for the sBSC and the other BTS units served by the sBSC. This BTS distributes the TOD protocol messages to other BTS units. The SNTP server on the first BTS is defined by an IP address. Each additional BTS unit served by the sBSC is configured to refer to the IP address of the SNTP server. For single isolated Pico installation where GPS synchronization for handoff is not required, there is also an option to use an external SNTP server for correct TOD eliminating the need to install a GPS unit. (see Figure 2.3) 2.2.2 sBSC The sBSC has the following features: � The sBSC is the iCell Soft Base Station Controller which can support several BTS units � The sBSC must be identified by the MSC � The sBSC is configured to refer to the IP address of the SNTP server 2.2.3 Global Positioning System (GPS) The following GPS-produced signals are used for each BTS when Soft or Hard Handoff is a requirement: � Time Of Day (TOD) message � Synchronized 1 PPS MovingMedia 2000 iCell Pico BTS Installation Guide Page 7 of 16 2.2.3.1 Direct GPS and Daisy Chain of 1 PPS source For in-building installations, the GPS receiver is connected to one BTS (the first BTS) in each cluster, directly through the 1 PPS IN SMA connector and the RS232 TOD port. The 1PPS signal can be extended via coax to other nearby BTS units using the “ 1PPSOUT”por toft hef st BTS going to the 1 PPS IN port of the next BTS. Optional 1 PPS Sector 1 Tx/Rx GPS Receiver TOD Rx dv IP Network Sector 2 Sector 3 Tx/Rx BTS Rx dv BSC Server IP Tx/Rx Rx dv 110-220 VAC 5.2V DC External SNTP Server for TOD if GPS not installed Figure 2-3: Optional GPS Signals MovingMedia 2000 iCell Pico BTS Installation Guide Page 8 of 16 2.2.4 Simple Network Time Protocol (SNTP) Server The SNTP server provides client and server services to obtain and set accurate date and time in network-connected devices. It operates in three selectable modes: � Unicast: A client sends a request to a designated time server at its unicast address and receives a response from which it determines the time. � Multicast: A time server periodically sends a message containing the current time to a designated multicast group address. The client listens on this multicast address. � Anycast: A client sends a request to a designated local broadcast address or multicast group address. One or more time servers reply with their own unicast address and the client binds to the first one it receives. The client continues operation in unicast mode. MovingMedia 2000 iCell Pico BTS Installation Guide Page 9 of 16 3 BTS PHYSICAL INSTALLATION 3.1 General This chapter provides physical installation and wiring instructions for the BTS. 3.2 Unpacking Upon receipt of, and before opening the iCell packages, inspect for any damage that might have occurred during shipping. If the package shows any signs of external damage or rough handling, notify your carrier's representative. CAUTION All modules are susceptible to electrostatic discharge (ESD) even while installed. Take the necessary precautions to minimize electrostatic damage while handling modules. Carefully remove all parts and hardware out of the packages. Carry out a full inventory before installation procedure starts. 3.2.1 BTS 19" Rack Mount Packing List The iCell 19" Rack Mount package includes the following: 1. 1U19”Chassi scompl et ewi hACorDCpowersuppl 2. Optional GPS Unit (Mandatory when CDMA Handoff is required) MovingMedia 2000 iCell Pico BTS Installation Guide Page 10 of 16 3.2.2 BTS Wall Mount Packing list The iCell wall mount package includes the following: 1. Pico BTS complete with cover 2. AC adapter unit 3. Wall Mounting bracket 4. Optional GPS unit (Mandatory when CDMA Handoff is required) 3.3 Mounting Instructions The section provides instructions for the following: � 19" rack mounting � Wall mounting 3.3.1 BTS 19" Rack Mount See Figure 3-1 and Figure 3-2. 1. Insert the BTS 1X 19" unit into a 19" rack. Secure with four NF10 screws. 2. Connect BTS 19" Rack Mount according to paragraph 3.4.2. Figure 3-1: BTS 19' Rack Mont Rear View Fi gur e3. 2:BTS19”RackMountFr ontVi ew MovingMedia 2000 iCell Pico BTS Installation Guide Page 11 of 16 3.3.2 BTS Wall Mount See Figure 3-3. BTS Wall Mount MovingMedia 2000 iCell Pico BTS Installation Guide Page 12 of 16 Perform the wall mounting. Mark the location of the drilling holes according to Figure 3-4. Drill three holes Hang the Mounting Bracket in the marked location and fasten with three screws. Mount the Power Supply onto the Wall Mount Bracket. Assemble the iCell unit to the bracket on the spacers. Connect a BTS module according to section 3.4.2. 130.0 cm (5.12") Figure 3-4: Hole Location for Mounting Bracket To comply with Maximum Permissible Exposure (MPE) requirements, the maximum composite EIRP output from the antenna cannot exceed 1.26 Watts EIRP and the antenna must be permanently installed in a fixed location that provides at least 13 cm of separation from all persons. This is maximum separation based on the possibility of connecting the Pico to a very high gain directional antenna of 11 dBi. A more typical 3 dBi gain antenna would result in a separation distance of 5 cm. 3.4 Interface Connections 3.4.1 BTS Interface Connections Verify that the power switch is off and the external AC power line is disconnected. 3.4.2 BTS Interface Connection Figure 3-7 illustrates the wiring diagram of the wall mount configuration and Table 3-4 provides the wiring parameters. MovingMedia 2000 iCell Pico BTS Installation Guide Page 13 of 16 MovingMedia 2000 iCell Pico BTS Installation Guide Page 14 of 16 BTS MCN Name Type Pri Eth RJ45S GPS TOD Destination Name Type Standard CAT5 Ethernet Switch RJ45S RJ45S 45-89332-M3 GPS DB9 Console RJ45S 45-89330-M3 PC DB9 1 PPS IN 1 SMA TBD GPS 1 PPS BNC Power Supply Switching 363-02155-0002 AC Power External Source Power or 363-06097-0015 NOTE All SMA connectors that are not connected should be terminated. MovingMedia 2000 iCell Pico BTS Installation Guide Page 15 of 16 3.4.2.1 Connecting to GPS To Connect GPS: Connect the GPS receiver ANT F-Type connector the GPS antenna cable. Connect the GPS receiver SERIAL DB9 connector the BTS GPS TOD connector with cable MCN 45-89332. Connect the BNC T receiver adaptor (female) to the BTS 1 PPS IN SMA connector with cable MCN 45-89800-1. 3.4.2.2 Miscellaneous Connections To connect the remainder connections: Connect BTS Primary Ethernet port through Internet switch to BTS. Connect BTS S1 Tx/RX1 to external antenna or to DAS for typical omni configuration. Rx diversity is not normally required for Pico in-building deployments. All unused SMA connectors should be terminated. For wall mount Pico, connect 4 pin DIN cable from AC adapter output to BTS 5.2VDC input and connect AC adapter to 110 or 220 V AC supply For AC Rack mount version, just connect the AC cord to 110 or 220 V AC supply. For DC Rack Mount version, make sure the main rack breaker is off and the BTS power switch is in the off position. Connect the –48v wire as indicated ont her earoft heuni tmar ked“ –“or“ –48v ”andt heposi e( Bat .Rt n)wi ot het er mi nal mar ked“ +”orBatRet ur n. The BTS unit is now ready for configuration and testing. MovingMedia 2000 iCell Pico BTS Installation Guide Page 16 of 16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Creator : Microsoft Word - User Manual Pico BTS.doc Producer : ScanSoft PDF Create! 2 Create Date : 2005:03:28 15:58:16 Modify Date : 2005:03:28 15:58:16 Author : perrella Title : Microsoft Word - User Manual Pico BTS.doc Page Count : 16 Page Mode : UseNoneEXIF Metadata provided by EXIF.tools