Starfield Electronic ZIPE21PSLB EM3586 ZigBee Module with PA User Manual

Starfield Electronic Limited EM3586 ZigBee Module with PA

User manual

Revision 0.6.1 Feb 2015 Product SpecificationsZigBee Module - ZiP E2.1-PSLB
Product Specifications Document History ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 2Document History Date Author(S) Revision Comments May-2014 Honky Yau v0.1 First release 14-July-2014 Honky Yau v0.2 Confirmed SPI IOs pin assignment Update Contact Information 23-July-2014 Honky Yau v0.3 Update 3.1 RF specification -Naming: Maximum input signal level -> Receiver input signal level -Max value : +5 dBm 30-Sep-2014 Honky Yau v0.4 Update Mechanical Dimension- Module Height: from 3.0 to 2.9mm-Module Height tolerance: from TBD to2.9 +/- 0.15mm10-Feb-2015 Vincent Tse v0.5 Updated Notice section 04-Mar-2015 Vincent Tse v0.6 Updated Notice & Ordering Guide
Product Specifications Contents ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 3Contents Contents ...................................................................................................................................................................... 3 1. Key Features .......................................................................................................................................................... 5 1.1. System Description .................................................................................................................................. 5 1.2. Feature ...................................................................................................................................................... 5 1.3. Block Diagram .......................................................................................................................................... 6 1.4. Module Pin Assignment .......................................................................................................................... 6 2. DC Electrical Specifications ............................................................................................................................... 10 2.1. Absolute Maximum Ratings ................................................................................................................. 10 2.2. Power consumption ............................................................................................................................... 10 2.3. nRESET Pin Characteristics ................................................................................................................ 10 3. Radio Performance .............................................................................................................................................. 11 3.1. RF Specifications ................................................................................................................................... 11 4. Environmental Specifications ............................................................................................................................. 12 4.1. Environmental Specifications ............................................................................................................... 12 5. Mechanical ............................................................................................................................................................ 13 5.1. Physical Dimensions ............................................................................................................................. 13 5.2. Recommended PCB pattern ................................................................................................................ 15 5.3. Label Drawing ........................................................................................................................................ 16 6. Ordering Guide ..................................................................................................................................................... 17 7. Notice..................................................................................................................................................................... 18
Product Specifications Contents ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 4
Product Specifications Key Features ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 51. Key Features1.1. System Description ZiP E2.1 is a ZigBee module targeting for Home Automation and Smart Energy marketplaces. The module embedded with a high performance Cortex M3 ZigBee transceiver EM3586 from Silicon Labs (SiLabs) which is fully compliant with IEEE 802.15.4-2003 specifications. It provides a low cost, low power consumption and reliable wireless communication solution in the 2.4GHz ISM frequency band. Customer can implement applications easily with various interfaces provided by ZiP E2.1. 1.2. Feature - Dimensions: 27.20mm x 14.75mm x 2.90mm - SiLabs Ember EM3586 high-performance, integrated ZigBee/802.15.4 chipset - Transmit power: up to +19 dBm - Receiver sensitivity: -103dBm - Supply voltage: 2.4V to 3.6V - Security: 128-bit AES - On-board chip antenna - Serial Interface: USB/SPI/UART/I2C - ADC: 14bits ADC port - FCC & RoHS compliant - MSL JEDEC level 3
Product Specifications Key Features ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 6 1.3. Block Diagram 1.4. Module Pin Assignment Pin# Pin Name I/O Description1 GND - Ground 2 Reserved - No connection 3 PC4/JTMS I/O Programmable I/O control, or JTAG mode select 4 PB0/IRQA I/O Programmable I/O control, or an interrupt input 5 PA3/SC2_nCS O Programmable I/O control, or External SPI serial flash, SPI nCS 6 PB6/ADC1/IRQB I/O Programmable I/O control, or ADC input, or an interrupt input
Product Specifications Key Features ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 77 PC1/ADC3 I/O Programmable I/O control, or an ADC input 8 SWCLK/JTCK I JTAG/Serial Wire debugging port clock 9 PC0/JRST/IRQD I/O Programmable I/O control, or an interrupt input, or the JTAG reset input 10 GND - Ground 11 PB5/ADC0 I/O Programmable I/O control, or an ADC input 12 GND - Ground 13 GND - Ground 14 GND - Ground 15 GND - Ground 16 Reserved - No Connection 17 GND - Ground 18 RFO O RF output for external antenna (option) 19 nRESET I Module reset signal (Internal pull-up) 20 GND - Ground 21 GND - Ground 22 PA3 I/O Programmable I/O control 23 GND - Ground
Product Specifications Key Features ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 8 Pin# Pin Name I/O Description24 PC6/OSC32B I/O Programmable I/O control, or 32.768kHZ crystal 25 PC7/OSC32A I/O Programmable I/O control, or 32.768kHz crystal 26 SC1SCLK/PB3 I/O SPI port 1 clock, or programmable I/O control 27 PA0/USBDM/SC2MOSI O Programmable I/O control, or USB D- signal, or External SPI serial flash SPI master data out 28 PA1/USBDP/SC2MISO I Programmable I/O control, or USB D+ signal, or External SPI serial flash SPI master data in 29 VBATT PWR Module power supply 30 PA2/SC2SCLK O Programmable I/O control, or External SPI serial flash SPI master clock 31 PA4/ADC4 I/O Programmable I/O control, or ADC input 32 GND - Ground 33 PA5/ADC5/nBOOTMODE I/O Programmable I/O control, or ADC input, or Boot control, must be left open or pulled high during the reset to enable the normal firmware boot process. 34 SC1MISO(s)/SC1MOSI(m)/ TXD/ SC1SDA/ PB1 I/O SPI port 1 MISO (slave)/ MOSI (master) signal, or UART TXD signal, or I2C port 1 DATA signal, or Programmable I/O control 35 SC1MOSI(s)/SC1MISO(m)/ RXD/ SC1SCL/ PB2 I/O SPI port 1 MOSI (slave)/ MISO (master) signal, or UART RXD signal, or I2C port 1 CLK signal, or Programmable I/O control 36 PC2/JTDO/SWO I/O Programmable I/O control, or Serial Wire port OUTPUT signal, or JTAG data out
Product Specifications Key Features ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 9 Pin# Pin Name I/O Description37 SC1nSSEL/PB4 I/O SPI port 1 slave select, or Programmable I/O control 38 PC3/JTDI I/O Programmable I/O control, or JTAG data in 39 GND - Ground 40 GND - Ground 41 GND - Ground 42 GND - Ground 43 GND - Ground 44 GND - Ground
Product Specifications DC Electrical Specifications ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 102. DC Electrical Specifications2.1. Absolute Maximum Ratings Parameters Test Conditions Min Max Unit Supply voltage -0.3 +3.6 (VDDmax) V Voltage on any GPIO -0.3 VDDmax V Under no circumstances the absolute maximum ratings must be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the device. 2.2. Power consumption VCC = 3.0V, Temperature = 25oC, FRF= 2440MHz (unless otherwise noted) Parameters Condition Min Typ Max Unit Sleep mode Internal RC oscillator on Processor, radio, peripherals off 1.2 uA Standby mode Processor on Radio and peripherals off 12 mA Receive mode Radio receive chain on 35 mA Transmit mode +19dBm typical 175 mA Serial controller current For each controller at maximum data rate 0.2 mA General purpose timer current For each timer at maximum clock rate 0.25 mA General purpose ADC current At maximum sample rate, DMA enabled 1.1 mA 2.3. nRESET Pin Characteristics Parameters Min Typ Max Unit Reset pulse width to guarantee a reset 200 300 ns
Product Specifications Radio Performance ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 113. Radio Performance3.1. RF Specifications VCC = 3.0V, Temperature = 25oC, Normal Mode measured at 50ohm terminal load Parameters Test Conditions Min Typ Max Unit Frequency range 2405 2475 MHz Transmitter power at maximum +19 dBm Receiver sensitivity -103 dBm Receiver input signal level +5 dBm Carrier frequency error -40 +40 ppm
Product Specifications Environmental Specifications ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 124. Environmental Specifications4.1. Environmental Specifications Parameters Min Max Unit Operating supply voltage +2.4 +3.6 V Operating Temperature -40 +85 C Storage Temperature -40 +85 C MSL Moisture Sensitivity Level 3 RoHS Restriction of Hazardous Substances Compliant
Product Specifications Mechanical ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 135. Mechanical5.1. Physical Dimensions
Product Specifications Mechanical ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 14 (Bottom view) (Top view)
Product Specifications Mechanical ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 15 5.2. Recommended PCB pattern (top view) (top view) Notes: To achieve best RF performance, it is recommended to follow the layout requirement as listed 1. The area in Zone1 (antenna area), all layers of customer circuit board should keep free from any metal objects 2. The area in Zone2, top layer of customer circuit board should have ground with no signal traces
Product Specifications Mechanical ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 16 5.3. Label Drawing
Product Specifications Ordering Guide ZiP E2.1-PSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 176. Ordering GuideOrdering Part Number Description Package Type P00-BI570PB-SFM0 ZiP E2.1-PSLB 2.4GHz ZigBee module (PA version) Tape & Reel
Product Specifications Notice ZiP E2.1-NSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 187. NoticeThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IC StatementThis device complies with Industry Canada licence-exempt RSS-210 standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FranceLe prsent appareil est conforme aux CNR-210 d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AD69ZIPE21PSLB Or Contains FCC ID: 2AD69ZIPE21PSLB The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
Product Specifications Notice ZiP E2.1-NSLB ZigBee Module Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 19 When the module is installed inside another device, the user manual of this device must contain below warning statements: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.
Intercel confidentialThis document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 20Contact InformationIntercel (China) LimitedUnit 6, 17/F, Vanta Industrial Centre, 21-33 Tai Lin Pai Road, Kwai Chung, New Territories, Hong Kong SAR, China t+852-2362 9018 f +852Į2648 8806Shenzhen Office Room 1303, 13/F, West Block, Tianan High-Tech Plaza Phase II, Tianan Cyber Park, Futian District, Shenzhen 518040, China t+86-755-8835 3778 f +86-755-8835 2489 The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. IntercelTM assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, IntercelTM assumes no responsibility for the functioning of undescribed features or parameters. IntercelTM reserves the right to make changes without further notice. IntercelTM makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does IntercelTM assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. IntercelTM products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the IntercelTM product could create a situation where personal injury or death may occur. Should Buyer purchase or use IntercelTM products for any such unintended or unauthorized application, Buyer shall indemnify and hold IntercelTM harmless against all claims and damages.

Navigation menu