Strategic Vista Technologies SV-01A-CAM WIRELESS CAMERA-TX User Manual 1
Strategic Vista Technologies Inc. WIRELESS CAMERA-TX 1
USERS MANUAL
ACCESSORY 2.4 GHz 4 CHANNEL COLOR
WIRELESS CAMERA SYSTEM
QUICK SET UP GUIDE
• Wireless Color Camera
• Power Adapter
• Metal Mounting Bracket and Screws
1. UNPACK SYSTEM CONTENTS FROM THE
GIFTBOX
2. CAMERA CONTROLS & FUNCTIONS
1. Attach the stand base to the wall or ceiling where you want to install the camera. Locate a wall stud or ceiling joist and secure
bracket using the three supplied screws.
2. Attach the camera to the stand and firmly tighten the swivel..
3. Attach the camera with the stand to the stand base and firmly tighten the joint knob on the stand base.
4. Connect the supplied 9V 300mA DC adapter to the DC IN jack at the rear of the camera and plug it into the electrical outlet.
Your wireless camera has both AC or battery option. When using the AC option with rechargeable batteries, your camera will
automatically switch to back up battery feature during a power outage providing you with uninterrupted power to the camera. The
battery option also provides you the flexibility to move the camera from room to room.
WIRELESS CAME RA - AC OP TION ONLY
1. Ensure the power switch on the camera is turned OFF.
2. Connect one end of the power supply to the DC IN jack located at the back of the camera. Plug the other end into an electrical outlet
WIRELESS CAMERA - USING RECHARGEABLE BATTERIES
1. Insert 8 rechargeable ‘AA’ batteries (not included) into the camera battery compartment. WARNING: TO PREVENT INJURY
AND/OR DAMAGE TO THE UNIT, ENSURE THE BATTERIES ARE ALIGNED PROPERLY AND BATTERY TYPES ARE NOT
MIXED.
2. Ensure the slide switch labeled Recharge/Alkaline is set to the ‘Rechargeable’ setting.
3. Carefully slide the batter compartment into the camera
4. Ensure the power switch on the camera is turned OFF.
5. Connect one end of the power supply to the DC IN Jack located at the back of the
camera. Plug the other end into an electrical outlet.
BATT ERY COMPARTMENT
POWER ADAPTER
WIRELESS COLO R CAM ERA
SLIDE IN
1. L ENS
2. MICROPHONE
Built- in condenser microphon e pr ovides
audio capability from camera to monitor
television
3. 2.4 GHz ANTENNA
High gain directional dipole antenna
sends Audio and Video signa ls to the
monit or.
5. STAND M OUNT ING SOCKET
Reinforcement lock for camer a sta nd.
6. CHANNEL SELECTOR SWITC H
Slide sw itch f or the channel 1-4
selection.
7. ON/OFF POWER SWITCH
Contr ols p ow er to the ca mera. Not e:
Please ensure you set the sw itch to the
OFF position before plugging the
AC adapter into the unit.
8. DC IN JACK
Plug the 9V(300 mA) AC Adap ter in
here.
WIRELESS CAM ERA – BATT ERY OPTION
3. WIRELESS CAMERA – INSTALLATION
FCC NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT
.
Image sensor
Lens
Picture element
Scanning system
Battery Life (assume 1300mAH)
Current Consumption
Scanning frequency
Sync. system
Resolution
Min. illuminations
Video Output
Gamma characteristics
Auto Iris
Microphone
Transmitting frequency
Modulation
RF out level
Video Input level
Audio input level
Antenna
Oper. temperature
Power source
Dimensions
Weight
Color CMOS
F2.0/f 3.7mm, 92°wide-a ngle lens
510 x 492 (Color)
2:1 interlace
3 Hours (Color)
300mA typ. (color)
15.734 KHz(H) 59.9Hz(V) ,EIA
Internal Synchroni zation
380 Lines (Color)
2 Lux (Color)
1.0Vp-p/75 Ohm
r=0.45
Electrical Auto Iris
Shutter sensitivity :1/60-1/100,000
Condenser
2.4 GHz-2.4835 GHz
FM
90dBu/V, 3m
1.0Vp-p/75 Ohm
2.0Vp-p/600 Ohm
Directio nal high dipole a nte nna
-14º to + 122º F or (-10ºC to + 50 ºC)
DC12V 500mA DC Adapter
7.3 (W) x4.7 (H) x 11(D ) cm o r
2.8’ (W) x 1.85’ (H) x 4.3’ (D)
118 grams or 3.79 Oz
ACCESSORY 2.4 GHz 4 CHANNEL COLOR
WIRELESS CAMERA SYSTEM
Manual
4. WIRELESS CAMERA - SPECIFICATIONS