Sunbeam L85R Remote Blanket Control for PTC (Single) User Manual Layout 1
Sunbeam Products, Inc. Remote Blanket Control for PTC (Single) Layout 1
Sunbeam >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 666818 |
| Application ID | RgXRkR9XncmIMB+xUeUJMA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 48.95kB (611895 bits) |
| Date Submitted | 2006-06-09 00:00:00 |
| Date Available | 2006-06-09 00:00:00 |
| Creation Date | 2006-03-06 14:22:45 |
| Producing Software | QuarkXPress(tm) 6.5 |
| Document Lastmod | 2006-05-17 20:33:37 |
| Document Title | Layout 1 |
| Document Creator | QuarkXPress(tm) 6.5 |
Rest & Relieve™ Therapeutic Mattress Pad USER MANUAL Sleep warm. Sleep well.™ www.sunbeam.com WELCOME Thank you for choosing the Sunbeam® Rest & Relieve™ Therapeutic Mattress Pad, the ultimate in sleeping comfort. It features adjustable heat zones that you can customize to suit your preferences, so you wake up well rested and refreshed. Table of contents: Step-by-Step Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Twin or Full Size Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Queen or King Size Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Care and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-21 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 How to Obtain Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. If you have any questions while setting up or using your Mattress Pad, please visit us at www.sunbeam.com or contact Sunbeam Consumer Care at (800) 892-7684. IMPORTANT INSTRUCTIONS DO NOT DESTROY IMPORTANT INSTRUCTIONS DO NOT DESTROY Warnings and Safeguards As with all electrical products, misuse of product or failure to properly follow the instructions may cause overheating, fire or personal injury. Please read the product label and all of the instructions before using your heated product. 1 DO NOT use this heated product with an infant, a child, an incapacitated or immobile person, a paraplegic, a quadriplegic, a diabetic, one insensitive to heat such as a person with poor blood circulation, or anyone who cannot clearly understand the instructions and/or operate the controls. 10 Be sure this blanket/mattress pad/throw is used only on an AC supply current circuit of 110-120 volts. DO NOT use with an extension cord. 11 May experience increased heat in areas where heated product is bunched or folded while in use. 12 Keep all dogs, cats and other pets away from this heated product. This is an electrical appliance that they can damage or be injured by. 2 DO NOT route electrical cords between the mattress and box spring. DO NOT allow cords to be pinched. 13 DO NOT use blanket/mattress pad on a waterbed, sofa, bunk bed or mechanically adjustable bed and do not use throw on a waterbed, bunk bed or mechanically adjustable bed. 3 DO NOT use with damaged cords. Damaged cords can lead to fire. DO NOT tuck in, trap, fold, cross or pinch cords between bed slats, mattress or springs, or against walls, footboards or bed frame. 14 For throw blankets: DO NOT use with rocking chairs, recliners, chairs with casters or wheels, or other furniture subject to movement. 4 DO NOT dry clean this heated product. Cleaning liquid may damage the insulation of the heating element. Improper laundering may cause problems with the heating wire which can lead to fire. 5 DO NOT tuck in, pinch, flex or expose the heating wire to rubbing. A damaged heating wire may result in possible overheating or fire. DO NOT tuck the heated product or supply cord in a sofa or other furniture. All portions of the heated product and controller should be visible at all times. 6 Turn off or unplug the control for the heated product when not using. 7 Wrapping the cord around the controller may damage the cord. Loop loosely when storing. 15 DO NOT use another electronic heating device in conjunction with your heated product. 16 Use the proper size blanket/mattress pad for your bed. For example, use a Twin Size warming blanket on a Twin Size bed. 17 If the following Important Instructions are not followed, the heated product will not operate properly. 18 Not for hotel, motel or other institutional use. 19 If you see the heated product operating improperly, unplug it immediately and call Sunbeam Consumer Care at 800-892-7684. 8 Keep the control away from drafty areas that may become damp or wet such as an open window. 9 DO NOT use pins; they may damage the electric wiring. For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com STEP-BY-STEP SETUP STEP-BY-STEP SETUP Your Sunbeam® Rest & Relieve™ Therapeutic Mattress Pad Includes: Base Unit Mattress Pad Setup 1 Place the Mattress Pad on the bed with the label at the foot of the bed facing outward. This puts the zones in the proper position to warm your body ergonomically. Zone Connector Cables & Plugs 2 Place the base unit on the floor under the bed, and run the Connector cable(s) along the floor to the foot of the bed. (DO NOT sandwich the cable(s) between the mattress and box spring. Avoid tangling or pinching.) 3 TWIN OR FULL SIZE: Connect the Blue plug to the Blue Connector until the plastic hinges click in place. QUEEN OR KING SIZE: Connect the Blue plug to the Blue Connector, and connect the Green plug to the Green Connector until the plastic hinges click in place. Mattress Pad Remote Control CAUTION: Cables must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 4 Plug the power cord into a 110–120 volt wall outlet. Installing the Batteries 1 Remove the battery compartment door from the back of the remote control. 2 Insert three AAA batteries, matching the + and – battery ends to the symbols in the battery compartment. 3 Replace the battery compartment door. For questions or support, please visit: www.sunbeam.com Important CAUTION: • DO NOT plug the power cord into the wall outlet until you have completely set up your Mattress Pad per the instructions. • Disconnect power cord from wall before detaching the base unit from the Mattress Pad. • DO NOT attempt to force the plug. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. For questions or support, please visit: www.sunbeam.com TWIN OR FULL SIZE MATTRESS PAD TWIN OR FULL SIZE MATTRESS PAD Remote Control At-a-Glance Features: Three adjustable heat zones for your individual total-body comfort 10 temperature settings per zone to create your ideal sleep experience Preheat setting to warm up your bed before bedtime Auto Off conveniently shuts off the Mattress Pad after 10 hours of operation ■ Cordless remote control operation for easy use from bed ■ Electronic display control with backlight for nighttime viewing ■ ■ ■ ■ Preheat warms the mattress before you get into bed. On/Off turns the mattress pad on and off. Heat Zones +/– adjusts the heat of each zone up or down. Blue Zone Neck and Shoulders Select Zone lets you adjust each heat zone individually. Blue Zone Lumbar Electronic Display shows zone settings with backlight for nighttime viewing. Auto Off/Stay On turns the automatic 10-hour shutoff feature on and off. Blue Zone Feet NOTE: To prevent accidental changing of your selections while the Mattress Pad is on, the remote control and display will lock during periods of inactivity. To reactivate the control, press any of the zones or the “ + ” or “ – ” buttons. For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Turning the Mattress Pad ON and OFF Adjusting Zones Individually Turn on the Mattress Pad on or off by pressing the “On/Off” button on the remote control. When on, the base unit will beep once, the display will light up, and all zones will appear outlined. NOTE: The backlight turns off after one minute to save battery power, but the Mattress Pad remains on. To turn the backlight on again, touch any button on the control other than the “On/Off” buttons. 1 To adjust any zone individually, press the “Select Zone” button that corresponds to the zone you want to adjust. That zone will become outlined on the display and will be the only zone that changes when you press the “ + ” and “ – ” buttons. Your customized heat settings are stored in memory so the next time you turn it on, the Mattress Pad returns to the same preferences as the last session. 2 Press the “ + ” or “ – ” button to adjust the heat of the selected zone. CAUTION: Always turn the Mattress Pad “Off” when not in use. 3 To change another zone’s setting, repeat Steps 1 & 2. Adjusting the Blue Zones at Once Selected zone will appear outlined NOTE: To Change all zones at once turn off the Mattress Pad and turn it back on. Or you can wait 60 seconds until the zone’s outline disappears, then press the “ + ” or “ – ” button. Highest Heat Your Mattress Pad features 10 adjustable heat levels per zone that can be increased or decreased together or separately. Preheating the Mattress Pad To adjust all the zones up or down from their current settings, press the “ + ” button to increase or the “ – ” button to decrease the heat. All the zones will change together in the same increments. To preheat: Never get into a cold bed again during the Winter season. Preheat warms your Mattress Pad before you get in. Turn Mattress Pad on. Press the “Preheat” button. All zones will show a “P” while they are preheating unless a zone is turned off. The zones will heat for 30 minutes and then return to their previously programmed heat settings. The display shows each zone’s heat setting: 1 through 9, and then H, which is the warmest setting. A “ – ” on the display indicates that the zone will not heat. NOTE: Zones with no heat setting (-) will not preheat. NOTE: To cancel preheat after activating it, press the “Preheat” button again. The Mattress Pad’s regular heat settings will resume. NOTE: At least one zone must be selected for the preheat function to work. Heat is Turned Off For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com OPERATING INSTRUCTIONS QUEEN OR KING SIZE MATTRESS PAD Auto Off Features: Auto Off conserves energy by automatically turning off the Mattress Pad after 10 hours of use. This is the factory default setting, and the display will read “Auto Off” when this feature is active. ■ ■ ■ ■ To deactivate Auto Off: press the “Auto Off/Stay On” button. The display will read “Stay On”, and the Mattress Pad will remain on until you turn it off manually using the “On/Off” button. Three adjustable heat zones for your individual total-body comfort 10 temperature settings per zone to create your ideal sleep experience Preheat setting to warm up your bed before bedtime Auto Off conveniently shuts off the Mattress Pad after 10 hours of operation ■ Cordless remote control operation for easy use from bed ■ Electronic display control with backlight for nighttime viewing Remote Control At-a-Glance To reactivate Auto Off: press the “Auto Off/Stay On” button until the display shows “Auto Off”. NOTE: After a power outage, turn the remote off then turn on again to turn the mattress pad back on. The timer of the Auto Off feature automatically resets. Preheat warms one or both sides of the mattress pad before you get into bed. Can preheat one or both sides of the mattress pad. Select Zone lets you adjust each heat zone for the Green side. Select Zone lets you adjust each heat zone for the Blue side. On/Off turns that side of the mattress pad on and off on the Green side. +/– adjusts the heat levels for each Green zone. On/Off turns that side of the mattress pad on and off on the Blue side. Auto Off/Stay On turns the automatic 10-hour shutoff feature on and off. Electronic Display shows zone settings with backlight for nighttime viewing. +/– adjusts the heat levels for each Blue zone. NOTE: To prevent accidental changing of your selections while the Mattress Pad is on, the remote control and display will lock during periods of inactivity. To reactivate the control, press any of the zones or the “ + ” or “ – ” buttons. For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 10 QUEEN OR KING SIZE MATTRESS PAD For Dual Users with a Queen/King Mattress Pad QUEEN OR KING SIZE MATTRESS PAD For Single Users with a Queen/King Mattress Pad For one-person use, you can set both sides of the queen or king size Mattress Pad to operate together as three wide zones. Green Zone Neck and Shoulders Blue Zone Neck and Shoulders Blue Zone Neck and Shoulders Blue Zone Lumbar Green Zone Lumbar Blue Zone Lumbar Blue Zone Feet 1 Turn remote control off. Green Zone Feet Blue Zone Feet Flip the switch on the back of the remote control to “One Side.” 2 To do this, flip the switch on the backside of the remote control from “One Side” to “Both Sides”. (“One Side” is for two-person operation. “Both Sides” connects the sides for a single user.) Flip the switch on the back of the remote control from “One Side” to “Both Sides.” 3 When the remote is set to “Both Sides” either side of the control operates the entire Mattress Pad as three side zones. For operating details, follow the “How to Use a Twin or Full Size Mattress Pad” instructions in this manual. 4 To return to dual-sided operation, flip the switch on the backside of the remote control to the “One Side” position. NOTE: As a precaution, if remote control was left on while flipping switch, the control will automatically turn off. Turn remote control back on. 11 For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 12 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Turning the Mattress Pad ON and OFF Adjusting Zones Individually To turn on each side of the Mattress Pad individually press the “On/Off” button on the Blue or Green side. When on, the base unit will beep once, the display for the selected side will light up, and all its zones will appear outlined. 1 To adjust any zone individually, press the “Select Zone” button that corresponds to the zone you want to adjust. That zone will become outlined on the display and will be the only zone that changes when you press the “ + ” and “ – ” buttons. NOTE: The backlight turns off after one minute to save battery power, but the Mattress Pad remains on. To turn the backlight on again, touch any button on the control other than the “On/Off” buttons. Your customized heat settings are stored in memory so the next time you turn it on, the Mattress Pad returns to the same preferences as the last session. CAUTION: Always turn the Mattress Pad “Off” when not in use. Adjusting all Green or Blue Zones at Once Highest Heat 2 Press the “ + ” button to increase or the “ – ” button to decrease the heat of the selected zone. 3 To change another zone’s setting, simply select the zone and adjust its heat level up or down. Selected zone will appear outlined NOTE: After customizing each zone, you may want to reset the “ + ” and “ – ” buttons to again control all the zones of that side at once. To do this, turn off that side of the Mattress Pad, then turn it back on. Or you can wait 60 seconds until the zone’s outline disappears, then press the “ + ” or “ – ” button. Your Mattress Pad features 10 adjustable heat levels per zone. Press the “+” button on the Green or Blue side to adjust heat settings. That side’s zones will change together in the same increments. The display shows each zone’s heat setting: 1 through 9, and then H, which is the warmest setting. A “ – ” on the display indicates that the heat for that zone is turned off. Heat is Turned Off 13 For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 14 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Preheating the Mattress Pad Auto Off Never get into a cold bed again during the Winter season. Preheat turns the heat up to warm your Mattress Pad before you get in. With this feature activated, each side starts preheating when it is turned on. This lets two people preheat their sides at different times. Auto Off conserves energy by automatically turning off each side of the Mattress Pad after 10 hours of use. This is the factory default setting, and the display will read “Auto Off” when this feature is active. 1 To turn on preheat, after the Mattress Pad is on, press the “Preheat” button. All zones will show a “P” while they are preheating. NOTE: Preheat will not work on zones selected to have heat turned off “–”. See adjusting Zones individually on page 14. 1 To deactivate Auto Off, press the “Auto Off/Stay On” button on the remote control. The display will then read “Stay On”, and the Mattress Pad will remain on until you turn it off using the “On/Off” buttons. The zones will heat for 30 minutes at the highest setting “H” and then return to their previously programmed heat settings. 2 To cancel preheat after activating it, simply press the “Preheat” button again. The Mattress Pad’s regular heat settings for each zone will resume. NOTE: At least one zone must be selected for the preheat function to work. Auto Off Deactivated 2 To reactivate Auto Off, press the “Auto Off/Stay On” button on the remote control. NOTE: After a power outage, the timer of the Auto Off feature automatically resets to the full 10 hours, but the Auto Off/Stay On setting remains as selected. Auto Off Activated 15 For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 16 CARE AND CLEANING Taking care of your Mattress Pad is easy and safe as long as you follow a few simple steps. We recommend washing before initial use. Before Washing or Storing 1 Disconnect power cord from wall BEFORE detaching control cord from the Mattress Pad. 2 Ensure that no cords are still connected and none of the wires have worn through the fabric. 3 Carefully follow all washing instructions or your Mattress Pad may shrink and possibly cause a fire hazard. • DO NOT submerge control in water. • DO NOT dry clean your Mattress Pad. Dry-cleaning solvents may damage the wires. • DO NOT use bleach or cleaning fluids. • DO NOT use a wringer. • DO NOT iron your Mattress Pad. • DO NOT use mothballs or sprays of any kind. • DO NOT reconnect the Mattress Pad or use it until it is COMPLETELY dry. • DO NOT wash or put into water the power cord or any of the product’s cords. CARE AND CLEANING Machine Drying CAUTION: Do not use commercial dryers or the dryers at your local Laundromat. They get too hot and would damage the wiring of the Mattress Pad. 1 Preheat the dryer on the “low” temperature setting for two minutes. 2 Place Mattress Pad into the dryer and tumble-dry for 10 minutes at a low temperature. 3 Remove the Mattress Pad while it is still damp and gently stretch it to its original size. 4 Drape the Mattress Pad over a clothesline or a shower rod. DO NOT use clothespins. 5 The Mattress Pad must be COMPLETELY dry before reconnecting the power plug or control plug. Hand Washing 1 Presoak the Mattress Pad for 15 minutes in mild soap and lukewarm water. 2 Gently squeeze the soapsuds through a few times. 3 Rinse in fresh, lukewarm water. Machine Washing 1 Presoak the Mattress Pad for 15 minutes in mild soap and lukewarm water. Hand Drying 1 Gently stretch the Mattress Pad back to its original size. 2 Wash in mild soap and lukewarm water on the “delicate” or “gentle” cycle in the washer for two minutes. Remember, do not use bleach. 2 Drape the Mattress Pad over a clothesline or hang over a shower rod. DO NOT use clothespins. 3 Rinse in fresh, lukewarm water. 3 The Mattress Pad must be COMPLETELY dry before reconnecting the power plug or control plug. 4 Spin dry in the washing machine. Then gently stretch to its original size. 17 For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 18 FREQUENTLY ASKED QUESTIONS FREQUENTLY ASKED QUESTIONS Q Who should NOT use the Rest & Relieve™ Therapeutic Mattress Pad? Q My remote control doesn’t work, and the display is blank. A The following people should NOT use the zoned Mattress Pad: A Check to make sure the batteries are installed properly, and that the + and –on the batteries match the diagram in the battery compartment. • • • • • • • • An infant Anyone under 18 years of age An incapacitated person A paraplegic A quadriplegic A diabetic Anyone insensitive to heat such as a person with poor blood circulation Anyone who cannot clearly understand the instructions and/or operate the controls Q My remote control doesn’t work even though the display is on. A Check to make sure the cable(s) are securely connected between the foot of the Mattress Pad and the base unit under the bed. If it still doesn’t work, the remote may be too far from the base unit to send proper signals. Try moving them closer together. If that does not work, make sure the power cord is securely connected to the wall outlet. If it is, check the wall outlet to be sure it is working properly. Q My base unit feels warm to the touch. Is this a problem? Q Preheat does not seem to work. A No. The base unit may feel warm to the touch when functioning properly. A Be sure all the zones you wish to preheat are turned on and set for heat. Zones that are set to “ – ” will not preheat. Q My Mattress Pad doesn’t heat properly. Troubleshooting checklist if your mattress pad doesn’t heat: • Are the cables securely connected to the base unit? • Is the base unit plugged securely into a wall outlet? • Is the wall outlet working properly? • Is the remote control turned on? • Are the correct zones turned on? • Is the heat level set between 1-H? • Did Auto Off turn off the power after 10 hours of use? • If you experienced a power outage, did you turn the remote control off then turn it back on? • Is the correct side of the mattress pad turned on (for queen and king size only)? A Your heated product is not a heating pad. It will not feel hot to the touch when laid out flat in a normal manner. Try the following fold test to see if it is operating properly: Q How do I set Preheat for selected zones only? A To skip preheating for any zone, first press its corresponding “Select Zone” button and lower its heat setting until a “ – ” appears on the display. Then press “Preheat”. Because the “ – ” indicates that heat is turned off, zones with this setting will not preheat and also will not heat once preheat is finished and the regular heat settings resume. Q Will the Mattress Pad remember my settings between sessions? A After you turn the Mattress Pad off, all of your settings will be remembered so that the next time you turn it on, the previously programmed settings will resume. However, when the batteries are removed from the battery compartment, this memory is cleared. Preheat must be started each time you wish to you use this feature. 1 Fold the Mattress Pad over three times. 2 Make sure the Connector cable(s) are plugged into the Connector(s) at the foot of the Mattress Pad, and then plug the power cord into a wall outlet. 3 Turn on your heated product, then turn all zones to the highest settings and wait five to seven minutes. 4 Put your hand between the folds, and you should feel the Mattress Pad warming up. This means it is working properly. CAUTION: DO NOT continue the test for more than seven minutes. DO NOT attempt to make any internal adjustments to this appliance. If you have tried all of the solutions above and the heated product still doesn’t work, stop using it immediately, disconnect the power cord and contact Sunbeam Consumer Care. 19 For questions or support, please visit: www.sunbeam.com Q What does a periodic beep and blinking light on the base unit mean? A The base unit is designed to notify you in the event that a problem has been discovered by beeping every 16 seconds and also flashing every 16 seconds when the control is on. (If you have a queen or king size Mattress Pad, your base unit has two lights, one for each side of the Mattress Pad. The blinking light will indicate which side of the pad has a problem.) First, check the heated product for visual damage. If no visual damage is found, unplug the system from wall outlet. Check that the control is well connected to the module. Plug the power cord into the wall outlet and turn the control On. If the product still does not operate after two or three times trying to reset, disconnect the power cord and contact Sunbeam Consumer Care. For questions or support, please visit: www.sunbeam.com 20 FREQUENTLY ASKED QUESTIONS Q How do I restart my Mattress Pad after a power failure? A Press the “On/Off” button to turn the remote control off, then press “On/Off” to turn the remote control back on. The Mattress Pad will begin to warm. Q I bought two Mattress Pads for different bedrooms, and they don’t seem to be operating correctly now. ® A When you have two more Sunbeam wireless remote-controlled devices in a home, there is a slight change their signals may interfere with each other. To solve this permanently, you can easily reset one of the remote controls and base units so they communicate using a different signal. Here’s how to do it: 1 Turn the remote control off. 2 Unplug its base unit from the wall, then replug it into the wall while the remote control is off. 3 Within two minutes, take the remote control and hold down “Preheat” and “Auto Off/Stays On” simultaneously for three seconds, until a number appears on the display. Once the base unit beeps, you may let go. The new settings will be remembered, even after a power failure. Q What do I do if my pet chews the cord, I lose my control or the control does not operate properly? A Please stop using the heated product immediately. Call our Consumer Service number listed under How to Obtain Warranty Service and ask for instructions on how and where to send the heated product. Q I have heard that some heated products have EMFs. What is this? A EMF stands for Electromagnetic Field. This is an electrical field that surrounds any wire that has current flowing along its length. Although several studies have been conducted to evaluate the impact, EMFs have not been proven to be harmful. In any event, Sunbeam® has reduced the strength of EMFs in its blankets/Mattress Pads/throws to very low levels. LIMITED WARRANTY Sunbeam Products Inc. (“Sunbeam”) warrants that for a period stated below from the date of purchase, this product will be free from defects in material and workmanship. • All heated products branded Arlington™ will carry a ONE-year limited warranty. • All heated products branded Sunbeam® HomeChoice™, SlumberRest® Cuddler™ and Cuddle Up® will carry a TWO year limited warranty. • All other heated products branded Sunbeam® and SlumberRest® will carry a FIVE year limited warranty. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Sunbeam dealers, service centers or retail stores selling Sunbeam products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly or repair or alteration by anyone other than Sunbeam or an authorized service center. Further, the warranty does not cover Acts of God, or Nature, such as fire, flood, hurricanes and tornadoes. Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Q What does the ETL label mean about safety of Sunbeam heated products? A Intertek Testing Services (ETL) is a certified, independent testing organization that tests products in accordance with UL safety standards and issues the ETL label for those products that meet the relevant UL standards. All Sunbeam® products are tested to UL standards and bear either the UL or ETL label to indicate that the product meets or exceeds UL/ETL safety standards for heated products. 21 For questions or support, please visit: www.sunbeam.com For questions or support, please visit: www.sunbeam.com 22
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2006:03:06 14:22:45Z Creator Tool : QuarkXPress(tm) 6.5 Modify Date : 2006:05:17 20:33:37+08:00 Metadata Date : 2006:05:17 20:33:37+08:00 Producer : QuarkXPress(tm) 6.5 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Format : application/pdf Title : Layout 1 Document ID : uuid:e48b8ec4-ad46-11da-b559-00145165f2c8 Instance ID : uuid:eb8ea291-8840-4ed9-9fd8-b5c1efda5675 Has XFA : No Page Count : 14 Creator : QuarkXPress(tm) 6.5EXIF Metadata provided by EXIF.tools