Sunbeam Em6910 Cafe Series Instruction Booklet ManualsLib Makes It Easy To Find Manuals Online!

: Sunbeam Sunbeam-Em6910-Cafe-Series-Instruction-Booklet-121524 sunbeam-em6910-cafe-series-instruction-booklet-121524 sunbeam pdf

Open the PDF directly: View PDF .
Page Count: 44

Download
Open PDF In Browser	View PDF

Waiting on Front
Cover from Energi

Contents
Sunbeam's Safety Precautions

2

About espresso coffee

3

Features of your Café Series®
Espresso Machine

4

Using the control panel

10

Reference guide to using your espresso
machine

13

Programming your espresso machine

20

Preparing your espresso machine
before use

22

Guide to the perfect espresso

23

Guide to milk texturing

25

Using the hot water dispenser	

26

Espresso recipes

27

Care and cleaning

29

Cleaning the group head

30

Descaling	

32

Advanced programming options	

34

	

Important instructions – retain for
future use.

Sunbeam’s Safety Precautions
therefore avoid any direct contact with the
	 SAFETY PRECAUTIONS FOR YOUR
steam wand or hot water tap.
SUNBEAM ESPRESSO MACHINE
•	 Always disconnect the plug from the power
•	 Always place the unit on a flat, level surface.
outlet prior to cleaning the espresso machine
•	 Do not operate without water in reservoir.
or
if there is any problem during the coffee
Fill reservoir with only clean and cold water.
making process.
Observe the maximum filling volume is 3 litres.
•	
Do
not allow the power cord to come into
•	 Do not remove the filter handle during the
contact with the hot parts of the espresso
espresso pour or water flow as the unit is
machine, including the cup warming plate, hot
under pressure. Removing the filter handle
water tap and steam wand.
during either of these operations can lead to a
•	 Do not place hands directly under the steam,
scalding or injury.
hot water or coffee pour as this can lead to a
•	 The steam wand and hot water tap become
scalding or injury.
very hot during texturing milk and water flow.
This may cause burns in case of contact,
	 Sunbeam is very safety conscious when designing
•	 Do not use an appliance for any purpose other
and manufacturing consumer products, but it is
than its intended use.
essential that the product user also exercise care
•	 Do not place an appliance on or near a hot gas
when using an electrical appliance. Listed below are
flame, electric element or on a heated oven.
precautions which are essential for the safe use of
•	 Do not place on top of any other appliance.
an electrical appliance:
•	 Do not let the power cord of an appliance hang
•	 Read carefully and save all the instructions
over the edge of a table or bench top or touch any
provided with an appliance.
hot surface.
•	 Always turn the power off at the power outlet
•	 Do not operate any electrical appliance with a
before you insert or remove a plug. Remove by
damaged cord or after the appliance has been
grasping the plug - do not pull on the cord.
damaged in any manner. If damage is suspected,
•	 Turn the power off and remove the plug when the
return the appliance to the nearest Sunbeam
appliance is not in use and before cleaning.
Appointed Service Centre for examination, repair
•	 Do not use your appliance with an extension cord
or adjustment.
unless this cord has been checked and tested by •	 For additional protection, Sunbeam recommend
a qualified technician or service person.
the use of a residual current device (RCD)
•	 Always use your appliance from a power outlet of
with a tripping current not exceeding 30mA in
the voltage (A.C. only) marked on the appliance.
the electrical circuit supplying power to your
appliances.
•	 This appliance is not intended for use by persons
(including children) with reduced physical, sensory •	 Do not immerse the appliance in water or any
or mental capabilities, or lack of experience
other liquid unless recommended.
and knowledge, unless they have been given
• 	Appliances are not intended to be operated by
supervision or instruction concerning use of the
means of an external timer or separate remote
appliance by a person responsible for their safety.
control system.
•	 Children should be supervised to ensure that they • 	This appliance is intended to be used in
do not play with the appliance.
household and similar applications such as: staff
•	 The temperature of accessible surfaces may be
kitchen areas in shops, offices and other working
high when the appliance is operating.
environments; farm houses; by clients in hotels,
motels and other residential type environments;
•	 Never leave an appliance unattended while	
bed and breakfast type environments.
in use.
	 If you have any concerns regarding the performance and use of your appliance, 	
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
	 Ensure the above safety precautions are understood.
2

About espresso coffee
Congratulations on the purchase of your
Sunbeam Café Series® Espresso Machine.
The Sunbeam Café Series® delivers quality,
style and superior performance capturing
the essence of the commercial kitchen.
Inspired by heavy-duty equipment found in
restaurants, cafés and bars, the Sunbeam
Café Series® is built to last. It brings together
a range of appliances designed to expertly
create authentic café food and beverages at
home.
Uncompromising blends of stainless steel,
brass and die-cast alloy characterise the
range. This combined with advanced
technology and functional design, guarantee
the performance, that each product will
surpass expectations.
The Sunbeam Café Series® Espresso Machine
features a twin pump, twin thermoblock,
TPTT™ system to ensure a stable water
temperature while also allowing simultaneous
production of espresso and steam to texture
milk.

The dedicated twin thermoblock heating
system takes away the waiting time for water
temperatures to change between pouring
espresso and producing steam. The twin
pumps enables the coffee maker to deliver
instant steam for texturing milk and at the
same time produce a serve of espresso just
like a commercial machine.
Another feature of the espresso machine is
the progressive pre-infusion. The pre-infusion
gradually releases water pressure pre-soaking
the coffee grinds before full water pressure
is applied. This in turn delivers greater body
and sweetness to the espresso.
The Café Series ® Espresso Machine is
designed with quality die-cast metal
components and includes many features that
make producing delicious espresso at home
even easier. We hope you enjoy your new
espresso machine and should you need any
further assistance please don’t hesitate to
contact the Sunbeam Coffee Hotline on 	
1300 881 861.

3

Features of your Café Series®
Espresso Machine
Warming plate
The large warming plate effectively prewarms cups helping to retain the essential
characteristics true of espresso - sweet, rich
tasting and aroma.
Variable steam control dial
Steam wand
A dedicated thermoblock and pump provide
an instant supply of powerful dry steam for
achieving silky, dense and rich milk. The
commercial 360° ball joint allows the steam
wand to be moved into the ideal position.
Commercial size group head
Commercial size group handle
Espresso gauge
The gauge measures the resistance to the
espresso pour.
Removable drip tray and grill
The large capacity die-cast metal drip tray is
lined with plastic, preventing staining from
espresso oils, lightweight for easy removal and
designed with no dirt traps for simple wipe down
cleaning.
Height adjustable rubber feet
The height adjustable feet ensure the espresso
machine is level on the benchtop. Additionally
integrated into the two back feet are rollers,
these allow the user to effortlessly move
the machine – great when trying to clean
underneath.
Single filter basket

4

Double filter basket

Programmable control panel
An easy to use control panel provides the
choice of manual operation or utilising the
programmed espresso pour lengths.
Hot water control dial
Hot water wand
Dispenses a controlled flow of hot water. For
ease of use the wand has a commercial 360°
ball joint.
3 litre water reservoir
Removable 3 litre water reservoir is fitted
with an anti-calc filter and hand grips for
easy filling.
Low water warning indicator
Accessories
All the essential accessories to make an
authentic café-quality espresso – 600ml
stainless steel milk texturing jug, barista
coffee tamp and spoon for measuring out
coffee.
Measuring spoon

600ml jug
Tamp

Single filter basket
Dual-floor

Double filter basket
Dual-floor

Cleaning Disc

5

Features of your Café Series
Espresso Machine

®

Twin Pump and Twin Thermoblock – TPTT™
System
The machine is fitted with a 15 BAR pump
for the espresso function, delivering the
pressure required for a complete extraction of
oils, coffee solids and aroma. An additional
4 BAR pump is dedicated to the steam
function, producing instant steam pressure
for texturing milk.

TPTT™ System – Simultaneous Use
True to commercial use, the unique
TPTT™ System features twin pumps and
twin thermoblocks, this allows the coffee
maker to texture milk and pour an espresso
simultaneously.

Independent thermoblock heating systems
lined with stainless steel, heat the water
ensuring the precise temperature is achieved
for each function eliminating waiting time
and reducing temperature fluctuations.

Espresso Gauge
The espresso gauge is an indicator of the
quality of the espresso pour and should be
used as a guide.
It measures the pressure or resistance
created by water being pumped through the
tamped coffee grinds in the group handle.
Whilst the needle is within the target area on
the gauge it indicates that a quality serve of
espresso has been made. This is indicated by a
Optimum	
Pour

Under
Extracted
Pour
6

Over
Extracted
Pour

Features of your Café Series® Espresso Machine continued

slow and steady pour of liquid espresso with a
consistency similar to that of dripping honey.
The crema should be dark golden in colour.
Should the needle fail to reach the target
area this is an indication that the serve of
espresso is ‘under-extracted’. This occurs
when water passes too quickly through the
tamped coffee grinds and is an indication
that either the grind needs to be made finer
or the filter basket has been under-dosed.
The pour is quick and light in colour and the
resulting crema is thin with a creamy light
brown colour.

Commercial Size Group Head & Group Handle
The group head, group handle and filters are
designed to commercial specifications using
brass and stainless steel components. These
elements help contribute to the preparation
of an espresso serve, as it allows the coffee
maker to pack the necessary amount of
coffee grinds, which then expand firmly and
evenly onto the shower screen.

When the needle goes beyond the target area
it is an indication that the serve of espresso
is ‘over-extracted’. This occurs when the
water passes very slowly through the tamped
coffee grinds and is an indication that either
the grind is too fine or the filter basket has
been over-dosed. In this situation the hot
water is in contact with the coffee grinds
for too long thus creating a burnt and bitter
tasting espresso. This is characterised by
the espresso only slowly dripping during the
entire pour and the crema is very dark.

7

Features of your Café Series® Espresso Machine continued

Filter Baskets
Supplied with the espresso machine are two
different sets of filter baskets – Standard
Filter Baskets (one and two cup) and DualFloor Filter Baskets (one and two cup).
The Standard Filter Baskets (one and two
cup) are the same specification as used with
commercial espresso machines and are less
tolerant to the quality of the coffee bean.
They have a single floor to the filter and if
held up to the light you can see many small
holes.
Note: For the optimum results Sunbeam
recommends that you use these filters with
this espresso machine.
To achieve the optimum espresso pour with
these filters it is best to grind the coffee
as you need it. Therefore we recommend a
conical burr grinder such as the Café Series ®
Grinder (Code EM0480) to ensure you have
complete control of the particle size and are
assured a consistent grind.
Note: If you don’t have a grinder and have
your coffee beans ground for you, then you
must request that the coffee is ground very
fine, the same fineness that would be used
on a commercial espresso machine.

8

The Dual-Floor Filter Baskets (one and two
cup) are designed to be used with preground coffee that is typically available at
supermarkets and delicatessens. They have
two floors, looking into the filter basket you
can see many small holes and when held up
to the light and looking at the under-side of
the filter you will see a single hole.
These pre-ground coffee types are often
vacuum packaged into a brick shape and
their packaging states that they are a
‘universal grind’ that can be used throughout
a variety of coffee makers. The particle size
of ‘Universal grind’ is too coarse for making
quality espresso, therefore the Dual-Floor
Filter Baskets are designed to compensate
for this by slowing the flow of liquid espresso
creating a subtle aeration to ensure a golden
crema. Dual-floor filters or similar designs are
used in most domestic espresso machines.
Control Panel
An easy to use control panel provides the
choice of manual operation or utilising the
programmed espresso pour lengths. The
programmed espresso pour is set to 30mls
per cup while the Program function allows
users to personalise and save their own
espresso volumes.

Features of your Café Series® Espresso Machine continued

Pre-Infusion
Pre-infusion is programmed into the
double
‘MANUAL’, single espresso and
espresso operations. It is a gradual increase
of water pressure pre-soaking the coffee cake
before full water pressure is applied. This in
turn delivers greater body and sweetness to
the espresso.
Anti-Calc Filter
An Anti-Calc water filter reduces impurities
that taint the flavour and odour of the
water, improving the taste and aroma of the
espresso brewed. Additionally, scale build up
is slowed reducing the frequency of cleaning
required.

The Anti-Calc water filter fitted inside the
3 litre water reservoir has a 12 month life
for domestic use and a 3 month life for
commercial use.
Note: Contact Sunbeam on 1300 881
861 for replacement filters (Part code:
EM69101).
Note: The espresso machine can operate
normally without the filter and is easily
removed by gently pulling it out.

9

Using the control panel
Power
Press the ‘POWER’ button once to turn the
espresso machine on. The light above the
‘POWER’ button will illuminate green and
start flashing; this is to indicate that your
espresso machine is on and is heating up.

Note: Before turning on the espresso machine
ensure that the steam and hot water control
dials are in the OFF position.
When the green light above the ‘POWER’
button stops flashing and turns to a constant
red light, this indicates that the espresso
machine is heated and ready to use. The
lights above the ‘MANUAL’, single and
  double espresso buttons will also show a
constant green light.

To turn the espresso machine off, simply
press the ‘POWER’ button, the red power
light and all other lights on the control panel
will turn off.
Manual
The ‘MANUAL’ button allows the coffee
maker to have complete control over the
length of the espresso pour.
Once the espresso machine is switched on
and heated, so the light above the ‘POWER’
button is red and the lights above the
‘MANUAL’, single and
double espresso
buttons show a constant green light, the
coffee maker is able to use the manual
10

operation. The coffee maker simply needs to
press to the ‘MANUAL’ button once to start
the pour and again to stop.
Important: Once the manual operation is
activated, before the espresso pour starts the
pre-infusion feature will release three short
bursts of gradual water pressure onto the
coffee cake. After this the full water pressure
is applied and the espresso will pour freely.
Note: When the coffee maker has activated
the manual operation the lights above the
single and
double espresso buttons will
go off. The lights above the ‘POWER’ and
‘MANUAL’ buttons will remain on.

Single Espresso
The single espresso function removes the
guesswork and is programmed to pour 30mls
of liquid espresso.
Tip: We recommend using the single cup
filter when using the programmed single
espresso operation.
Once the espresso machine is switched on
and heated, so the light above the ‘POWER’
button is red and the lights above the
‘MANUAL’, single and
double espresso
buttons show a constant green light, the
coffee maker is able to use the single
espresso operation. The coffee maker simply
needs to press the single espresso button
once to start and the pour of liquid espresso
will stop automatically.
Important: Once the single espresso
operation is activated, before the espresso
pour starts the pre-infusion feature will
release three short bursts of gradually

Using the control panel continued

increasing water pressure onto the coffee
cake. After this the full water pressure is
applied and the espresso will pour freely.
Note: When the coffee maker has activated
the single espresso operation the lights
above the ‘MANUAL’ and
double
espresso buttons will go off. The lights above
the ‘POWER’ and single espresso buttons
will remain on.

Note: The coffee maker does not need to press
the single espresso button again to end
the pour as the espresso machine will stop
automatically.

button once to start and the pour of liquid
espresso will stop automatically.
Important: Once the
double espresso
operation is activated, before the espresso
pour starts the pre-infusion feature will
release three short bursts of gradually
increasing water pressure onto the coffee
cake. After this the full water pressure is
applied and the espresso will pour freely.
Note: When the coffee maker has activated
the
double espresso operation the lights
above the ‘MANUAL’ and single espresso
buttons will go off. The lights above the
‘POWER’ and
double espresso buttons
will remain on.

Once the pour of liquid espresso stops the
espresso machine is ready to make another
espresso.
Note: When using the single espresso
operation you can stop the pour of espresso
at any time by pressing the ‘MANUAL’,
single, or
double espresso operation
buttons.
Double Espresso
double espresso function removes
The
the guesswork and is programmed to pour
60mls of liquid espresso.
Tip: We recommend using the double cup
filter when using the programmed
double
espresso operation.
Once the espresso machine is switched on
and heated, so the light above the ‘POWER’
button is red and the lights above the
‘MANUAL’, single and
double espresso
buttons show a constant green light, the
coffee maker is able to use the
double
espresso operation. The coffee maker simply
needs to press the
double espresso

Note: The coffee maker does not need to press
the  
double espresso button again to end
the pour as the espresso machine will stop
automatically.
Once the pour of liquid espresso stops the
espresso machine is ready to make another
espresso.
Note: When using the
double espresso
operation you can stop the pour of espresso
at any time by pressing the ‘MANUAL’,
single, or
double espresso operation
buttons.
Program
The program function allows the coffee maker
to personalise and save their own espresso
pour settings.
Note: Refer to the section ‘Programming
your espresso machine’ for simple to follow
instructions.
11

Heading

Using the control panel continued

Once the espresso machine is switched on
and heated, so the light above the ‘POWER’
button is red and the lights above the
‘MANUAL’, single and
double espresso
buttons show a constant green light, the
coffee maker is able to use the program
function. To activate the program function,
the coffee maker simply needs to press
‘PROGRAM’ button.

Note: When the coffee maker has activated
the program function the light above the
‘PROGRAM’ button will show a constant
red light and the light above the ‘MANUAL’
button will go off. Additionally the lights
above the ‘POWER’, single and
double
espresso buttons will remain on.

Note: For more detailed information on
programming refer to page 20 ‘Programming
your espresso machine.’

12

Reference guide to using your
Heading
espresso machine
The diagrams below and on the following pages are to assist you in operating your Café Series®
Espresso Machine. Throughout the instruction booklet reference will be made to these diagrams,
so each of them has been numbered for convenience and ease of use.
For example: Fill the water reservoir (1) (2) (3) (4) (5) with cold tap water…..
Each time you see these numbers please refer back to these diagrams.
Preparing the espresso machine

1
Open lid of water reservoir.

4
Remove water reservoir.

2
Fill in place with cold water,
OR

3
Open rear door to access
reservoir

6

5
Fill at sink with cold water.

Press 'POWER' button to turn
unit on.
Double filter 	
basket
Single filter
basket

7
Control panel lit and ready
to use.

8

9

Warming the espresso cups.

Select appropriate filter and
place into group handle.
13

Reference guide to using your espresso machine continued

10
Place group handle onto
group head.

11
Turn group handle to the
right so it is firmly locked
into position.

12
Place large container under
both pouring spouts.

Making the espresso

13
Press the 'MANUAL' button
and allow the water to run
through.

16
Place finely ground coffee
into filter basket.

14

14
Select appropriate filter and
place into group handle.

15
Hold group handle under
group head and purge with
water to preheat.

18

17
Tamp the coffee. The level of
coffee must be 3mm below
the filter basket rim.

Wipe the edge of filter to
remove any coffee grinds.

Reference guide to using your espresso machine continued

20

19
Place group handle onto
group head.

Turn group handle to the
right so it is firmly locked
into position.

22
Press 'MANUAL' button for a
continuous pour.

21
Place glasses/cups below
pouring spouts.

23
Press the button for a
single serve of espresso.

24
Press the
button for a
double serve of espresso.
Programming
Double filter basket

Single filter
basket

26

25
Remove group handle by
turning to the left.

Discard the used coffee
grinds.

27
Fit the group handle with
appropriate filter basket.

15

Reference guide to using your espresso machine continued

28
Fill with finely ground coffee.

Tamp the coffee grinds.

31
Turn group handle to the
right so it is firmly locked
into position.

30

29
Place group handle onto
group head.

32
Press the 'PROGRAM' button.

33
Press the single espresso
button to start and end the
pour.

Texturing milk

35

34
Press the
double
espresso button to start and
end the pour.

16

Purge the steam wand by
turning dial clockwise.

36
Turn off steam by turning
dial anti-clockwise.

Reference guide to using your espresso machine continued

37
Swing steam wand to the
side of espresso machine.

38

39

Place steam wand into milk,
approx. 1cm below surface
and activate the steam
function.

Angle jug to rest steam wand
on spout and place nozzle
just below surface of the
milk.

40
Close the steam by turning
dial anti-clockwise.

41
Wipe steam nozzle and wand
with damp cloth.

Hot water

42
Place cup under hot water
nozzle and activate the hot
water function.

43
Close the hot water by
turning dial clockwise.

44
Swing hot water wand over
the drip tray.

17

Heading

Reference guide to using your espresso machine continued

Cleaning

45
Remove the grill.

47

46
Remove drip tray.

Wrap steam wand with damp
cloth and turn steam on for
10 seconds.

Double filter
basket

49

48
Insert cleaning pin into
the hole, at base of steam
nozzle.

Remove cleaning disc from
inside the rear door.

51
Position cleaning disc inside
the double filter basket.

18

50
Fit group handle with the
double filter basket.

52
Place cleaning tablet into
filter basket with cleaning
disc.

53
Place group handle onto
group head.

Reference guide to using your espresso machine continued

54
Turn group handle to the
right so it is firmly locked
into position.

55
Place large container under
both pouring spouts.

56
Remove group handle from
the group head.

19

Heading
Programming
your espresso
machine
The Café Series® Espresso Machine has
programming capabilities. Based on café
settings the single and
double
espresso functions are set at 30 and 60mls.
However by following a few simple steps the
coffee maker can personalise the espresso
machine to achieve a serve of espresso to
exactly how they like it.
Programming Single Espresso
1.	Prepare the filter handle. Fit the group
handle with the single filter basket (27)  
and fill with finely ground coffee (28).
Using the coffee tamp supplied, tamp
the coffee grinds (29). Secure the group
handle to the group head (30)(31).
2.	 Place a cup under both pouring spouts.
3.	To commence programming press the
‘PROGRAM’ button (32). The light above
the ‘PROGRAM’ button will show a
constant red light and the light above the
‘MANUAL’ button will go off. Additionally
the lights above the ‘POWER’,   single
and
double espresso buttons will
remain on.
4.	Press the single espresso button once
to start the espresso pour (33). The light
above the
double espresso button will
go off and only the ‘POWER’, single
espresso and ‘PROGRAM’ lights will remain
on.
5.	Allow the espresso to pour until the desired
level. Once the desired level is reached
stop the espresso pour by pressing the
single espresso button. 2 beeps will
signify that the new setting for the single
espresso operation has been programmed
and stored into the machines memory.
6.	The espresso machine will then return to
normal operation mode and is ready to
make another espresso at the push of a
button.
20

Programming
Double Espresso
1.	Prepare the group handle. Fit the group
handle with the double filter basket (27)
and fill with finely ground coffee (28).
Using the coffee tamp supplied, tamp
the coffee grinds (29). Secure the group
handle to the group head (30)(31).
2.	Place two cups under each pouring spout.
3.	To commence programming press the
‘PROGRAM’ button (32). The light above
the ‘PROGRAM’ button will show a
constant red light and the light above the
‘MANUAL’ button will go off. Additionally
the lights above the ‘POWER’, single and
double espresso buttons will remain
on.
4.	Press the
double espresso button once
to start the espresso pour (34). The light
above the single espresso button will
go off and only the ‘POWER’,
double
espresso and ‘PROGRAM’ lights will remain
on.
5.	Allow the espresso to pour until the desired
level. Once the desired level is reached
stop the espresso pour by pressing the
double espresso button. 2 beeps
will signify that the new setting for the
double espresso operation has been
programmed and stored into the machines
memory.
6.	The espresso machine will then return to
normal operation mode and is ready to
make another espresso at the push of a
button.
Resetting the Factory Settings
To revert back to the original factory settings;
1.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
	

Heading

Programming your espresso machine continued

	 Important: Although the espresso machine
is on at the power outlet ensure that the
actual espresso machine power is ‘OFF’.
Therefore no lights will be illuminated on
the espresso machine control panel.
2.	Press and hold down the ‘MANUAL’ button.
While still holding down the manual button
briefly press the ‘POWER’ button and then
release the ‘MANUAL’ button.

3.	When you hear the 4 beeps and the power
light flash the espresso machine will have
returned to the original factory settings and
the next time the single or double espresso
functions are used the espresso pours will
be 30 and 60mls.

21

Heading your espresso machine
Preparing
before use
1.	Place the espresso machine onto a dry,
stable benchtop.
2.	Ensure the drip tray and grill are in place.
3.	Fill the espresso machine with water. There
are a couple of ways in which the water
reservoir can be filled;
	 a) Simply lift the lid of the water reservoir
at the top of the espresso machine (1)
and using a jug, fill with fresh cold
water or filtered water (2).
	 b) Alternatively the water reservoir can
be removed and filled with fresh cold
water. To do so, open the door on the
back of the espresso machine (3) and
simply slide out the water reservoir (4).
Then fill with fresh cold water or filtered
water (5). Replace the water reservoir
firmly and shut the door.
4.	Insert the power cord into a 230-240V
AC power outlet and switch the power on.
Press the ‘POWER’ button once to turn the
espresso machine on (6). The light above
the ‘POWER’ button will illuminate green
and start flashing, this is to indicate that
your espresso machine is on and is heating
up.
	 When the green light above the ‘POWER’
button stops flashing and turns to a
constant red light, this indicates that the
espresso machine is heated and ready to
use. The lights above the ‘MANUAL’,
single and
double espresso buttons will
also show a constant green light (7).

22

Note: Before turning on the espresso machine
ensure that the steam and hot water control
dials are in the OFF position.
5. Place glasses and cups on the warming
plate (8).
Important: For first time use or if the machine
has not been used for some time, it is
important that the machine is rinsed as
follows:
6.	Fit the group handle with either the single
or double filter basket (9). Secure the
group handle to the group head (10) (11).
7.	Place a sufficiently large container under
both pouring spouts (12).
8.	Once the espresso machine is switched
on and heated, so the light above the
‘POWER’ button is red and the lights above
the ‘MANUAL’, single and
double
espresso buttons show a constant green
light, the espresso machine is heated and
ready to use.
Tip: Remember if the ‘POWER’ light is
flashing green, this indicates that the
espresso machine is on and is heating up.
9.	 Press the ‘MANUAL’ button (13) and allow
the water to run through until the water
reservoir is empty.
Note: As a safety mechanism the espresso
machine is programmed to automatically stop
the water flow after 240mls, therefore you
will need to press the ‘MANUAL’ button again
to restart the water flow.

Heading
Guide
to the perfect espresso
Preheat Glasses
1.	Preheat the glasses/cups by filling them
with hot water as this will assist to preserve
the crema of the espresso. Set the glasses/
cups aside.
Preheat Group Handle and Filter Basket
2.	Select the appropriate filter basket and
place it into group handle (14).
3.	Take the group handle, hold it under the
group head and purge water. With the filter
basket positioned under the group head
press the ‘MANUAL’ button to start the
water flow and press it again to stop (15).

expand up and onto the shower screen.
Tip: The coffee dosage and the degree of
tamping should remain the same every time
you make a coffee the only thing that should
vary is the particle size of the coffee grounds
and this will vary depending on the bean. For
example to achieve a slower espresso pour
rate use a finer grind and a coarser grind for
a faster espresso pour rate.
Note: If purchasing pre-ground coffee or have
someone grind it for you, request/purchase a
very fine grind, the same that would be used
for a commercial epresso machine

4.	Dry the filter basket.

Tip: Ensure the coffee tamp is dry because if
it is wet the coffee grinds will stick to it.

Dosing and Tamping
5.	Using a grinder or the measuring spoon
supplied, place the appropriate amount of
ground coffee into the filter basket (16).

The Espresso Pour
8.	Lock the group handle onto the group head
(19)(20).

6.	Rest the group handle with the filter
basket in position onto the benchtop. Take
the coffee tamp, apply firm level packing
pressure (17), twisting 90 degrees to
polish the grounds. This seals the surface
of the coffee cake.
7.	Brush any excess coffee grounds from
around the edge of the filter basket (18).
Important: Be sure to place a sufficient
amount of coffee grinds into the filter basket.
Once tamped the level of coffee should be
only a few millimetres below the rim of the
filter basket. To check this, lock the group
handle onto the group head (19)(20). Then
without having made a coffee remove the
group handle (25) and inspect the top of
the tamped coffee - it should have only a
slight indent from the shower screen. Ideally
the top of the tamped coffee should be
fractionally below the shower screen and then
during the espresso pour the coffee cake will

9.	Empty the glasses/cups and place below
the pouring spouts (21).
Note: Check to see that the espresso
machine is ready for use, remember that
if the ‘POWER’ light is flashing green, this
indicates that the espresso machine is on
and is heating up.
10.	Press the required volume button;
‘MANUAL’ for a continuous pour (22),
the single espresso for a 30ml pour
(23) or the
double espresso for a
60ml pour (24).
Note: When using the ‘MANUAL’ operation
the coffee maker must press the button
once to start the pour and again to stop the
pour. However with the single and  
double espresso operations the coffee maker
need only to press these buttons once to
start the espresso pour and the program
will automatically stop the pour at the preprogrammed level.
23

Heading

Guide to the perfect espresso continued

Important: Should coffee grinds come out
from the top of the group handle this is a
sign that the group handle has not been
firmly locked into position and/or the level of
coffee in the basket is too high.

Caring for your Espresso Machine
14.	Remove the group handle from the group
head (25).

Pre-Infusion
11.	Once an espresso operation has been
activated, before the espresso pour starts
the pre-infusion feature will release three
short bursts of gradually increasing water
pressure onto the coffee cake. After this,
the full water pressure is applied to the
coffee cake and the espresso will pour
freely.

Tip: After each use of the espresso machine
we recommend that a small amount of
water is cycled through the group head as
this will wash out any old or used coffee
grinds stuck to the underside of the
group head. Simply press the ‘MANUAL’
button and allow some water to run
through.

12.	Check the espresso pour. The ideal
pour starts out dark and then soon
after becomes caramel with reddish
reflections. The pour should hang
vertically on each spout and flow slowly
like dripping honey.
Tip: The espresso gauge provides an
indication of the resistance created by
the dosing of the filter basket and the
particle size of the grind. Referring to the
gauge will be a sign that one or both of
these elements may need adjusting.
Tip: Once the espresso pour starts to lighten
in colour you should cut off the pour.
13.	Serve espresso immediately.

24

15. Discard the used coffee grinds from the
filter basket (26).

Sleep Mode
After 1 hour of non-use the espresso machine
will automatically switch to ‘SLEEP MODE’.
An indication that the machine is in ‘SLEEP
MODE’ is the light above the ‘POWER’ 	
button will slowly flash red. While in 'SLEEP
MODE' the machine powers down to 70% of
power. After a further 26 hours of non-use
the espresso machine will turn off.
Note: To bring the espresso machine out of
'SLEEP MODE' you can press any button.

Heading
Guide
to milk texturing
Milk texturing is the steaming of milk. The
steam does two things, heats the milk and
also the steam mixes air with the milk to
form an ‘emulsion’ of tiny bubbles that gives
a silky velvet texture. Similar to making an
espresso, perfecting the art of milk texturing
takes time and practice.
Tip: Remember espresso is the foundation for
all espresso-coffee drinks and the milk is the
variable.
1.	 Determine how much milk is needed
based on the number of cups being made
or the size of the texturing jug.
Tip: Keep in mind that the volume of milk
will increase or ’stretch’ during the texturing.
2.	 Pour cold refrigerated milk into a
stainless steel jug, between to ²/³ full.
Tip: Best results will be achieved by using a
clean jug and cold, fresh milk.
3.	 Purge the steam wand of any water.
With the steam wand positioned over the
drip tray activate the steam function by
turning the steam control dial clockwise
as far as it will go (35). Once any water
has been purged close the steam by
turning the steam control dial anticlockwise (36).
4.	 Swing the steam wand to the side of the
espresso machine (37).
5.	 Place the steam wand into the milk
so that the tip of the steam nozzle is
just below the surface of the milk and
activate the steam function by turning
the steam control dial clockwise as far as
it will go (38).
6.	 Angle the jug so that the steam wand is
resting on the spout of the jug and lower
the jug until the tip of the steam nozzle
is just below the surface of the milk. This
will start to create a whirlpool action in
the milk (39).

Note: How we introduce the air to the milk
will determine the consistency of the foam.
If we catch large gulps of air the quality of
the foam will reflect this by having large
bubbles. If we can introduce air to the milk
in a controlled gentle fashion indicated by a
gentle hissing sound the milk will have a fine
aerated bead in the textured foam.
7.	 As the steam heats and textures the milk,
the level of the milk in the jug will begin
to rise. As this happens follow the level
of the milk by lowering the jug, always
keeping the tip of the steam nozzle just
below the surface. This will create a
slight hissing noise.
Tip: The amount of foam required will vary
depending on the drinks being made, for
example a cappuccino requires more foam
than a flat white.
8.	 Close the steam immediately when the
milk is heated to between 60-65°C
by turning the steam control dial anticlockwise (40).
Tip: The optimum drinking temperature of
milk is between 60-65°C and we advise
you use a milk thermometer to achieve
the correct temperature. It's important to
remember that if the milk is not heated long
enough the drink will be too cool and if the
milk is heated for too long it will start to boil
at around 72°C and all texture will be lost.
Tip: If you don’t have a thermometer a good
indication that the correct temperature has
been reached is when the jug becomes too
hot to leave your fingers in contact.
Important: Do not boil the milk as the texture
and taste will be affected.
9.	 Remove the jug and wipe the steam nozzle
and wand with a clean damp cloth (41).
10.	With the jug in hand tap the jug on the
bench top to release the trapped air
bubbles. Agitate the milk as this helps
the milk and froth combine for an even
25
consistency.

Using the hot water dispenser
Heading
The hot water dispenser is ideal for preparing
long blacks, hot chocolate and filling coffee
plungers.
1.	Swing the hot water wand to the side of
the espresso machine.
2.	Place the cup or container under the hot
water nozzle and activate the hot water
function by turning the hot water control
dial anti-clockwise as far as it will go (42).

26

3.	Once you have dispensed the required
amount of hot water into the cup or
container, close the hot water by turning
the hot water control dial clockwise (43).
4.	Remove the cup or container and swing the
hot water wand over the drip tray to catch
any drips of water (44).

Espresso recipes
ESPRESSO (SHORT BLACK)

MACCHIATO

Espresso is a concentrated, full bodied coffee
with a stable layer of cream on top – known
as ‘crema’. An espresso is the foundation of
all café coffee. Variations are achieved by
adding different amounts of milk and froth.

Macchiato, Italian for ‘to stain or mark’.
Traditionally served as a standard espresso
with a dash of milk and a small dollop of
froth into the middle of the ‘crema’.
• 90mL espresso glass or demitasse cup

• 90mL espresso glass or demitasse cup

• single or double espresso

• single espresso (30-35mL)

• marked with steamed milk froth

LONG BLACK

FLAT WHITE

A standard espresso with hot water, served in
a regular coffee cup or mug. The hot water is
added first so that the ‘crema’ is maintained.

Another old favourite, the Flat White is
an espresso with steamed milk, served in
a regular coffee cup or mug. The layer of
frothed milk on top should be 2mm to seal
the coffee.

• 190mL cup
• hot water (to taste)
• single or double espresso

• 190mL cup
• single or double espresso
• steamed milk

27

Espresso recipes continued

CAFFE LATTE

CAFFE MOCHA

An espresso with steamed milk, typically
served in a glass. The layer of frothed milk on
top should be 10mm to seal the coffee.
• 220mL glass or cup

Made in a similar way to a cappuccino but
with the addition of drinking chocolate.
Simply stir the chocolate into the espresso
prior to adding the steamed milk and froth.

• single or double espresso

• 190-240mL cup or tall glass

• steamed milk

• single or double espresso
• two teaspoons of drinking chocolate
• two-thirds milky coffee, one-third froth

CAPPUCCINO

CON PANNA

This delicious drink is an espresso with
steamed milk, topped with creamy froth and
a dusting of chocolate. The resulting drink is
approximately two-thirds milky coffee, onethird froth.

A variation on the original Vienna coffee, this
delicious drink is made up of an espresso
topped with lightly whipped cream. It can
also be dusted with cinnamon or drinking
chocolate.

• 190-240mL cup

• 190mL cup

• single or double espresso

• single or double espresso

• two-thirds milky coffee, one-third froth

• lightly whipped cream

• dusted with chocolate

• dusted with cinnamon or chocolate

28

Care and cleaning
The coffee making process involves extracting
oils out of coffee grinds to make espresso
coffee. Deposits of these oils build up over
time and affect the taste of the coffee and
operation of the espresso machine.
Regular cleaning to remove these oils is
essential and will maintain the quality of the
coffee the espresso machine produces and
result in less maintenance being required.
This is easy to do by following a few quick
and easy cleaning steps after each coffee
making session;
	  Cycle water through the group head,
	  Purge steam through the steam wand,
	 Wipe the steam wand clean with a damp
cloth immediately after use,
	 Remove the filter basket from the filter
handle and clean away any old coffee oils,
and
	 Empty the drip tray and rinse.
Important: Never wash any of the espresso
machine parts or accessories in the
dishwasher.
Drip tray and grill
Remove the grill and drip tray at regular
intervals to empty (45) (46). Clean with
water and a little non-abrasive washing up
liquid, rinse and dry.
Group head, group handle & filter baskets
The filter baskets and group handle should
be rinsed with warm water after each use and
then dried thoroughly.
To clean the group head of any old coffee
grinds cycle water through and wipe the
group head and around the inside rim with a
damp cloth.
Should the holes in the filter baskets become
clogged with coffee grinds use a fine bristled

brush to remove them. Also you can use
the cleaning pin which is supplied with
the espresso machine. The cleaning pin is
attached to the cleaning disk, located on the
inside of the back door (49). The cleaning
pin has two pins at either end - one is
labelled 'FILTER' and is the shorter of the
two and is for cleaning out the holes in the
filter basket.
Note: When cleaning the dual-floor filters
be sure to check the single hole on the
underside of the filter.
Group head rubber seal
The group head seal is located on the
underside of the group head and creates
a seal against the filter handle during the
espresso pour.
Note: During long periods of non-use we
recommend that the filter handle not be
left attached to the group head as this will
reduce the life of the seal.
Over time the seal will loose its elasticity
and require replacement, depending on use
usually every 12 months. Signs that the seal
is deteriorating are when the group handle
cannot create the necessary seal and steam
and or water escapes from around the group
head during the espresso pour. Another sign
may be when the group handle locks off to
the right rather than the front.
Note: Contact Sunbeam on 1300 881 861
should you think that the group head seal
needs replacing. Please do not attempt to
change the seal without first consulting
Sunbeam.
Cup warming plate, hot water wand and exterior
Wipe over the unit with a damp cloth and
wipe dry. Do not use abrasives or metal
scourers as these will scratch the exterior
surface.
29

Care and cleaning continued

Steam wand
Keeping the steam arm clean is essential
to ensure maximum efficiency of the steam
function. A build up of caramelised/dried
milk on the steam wand will impair the
steaming and texturing ability of the espresso
machine.
Important: Wipe the steam wand clean with a
damp cloth immediately after each use and
purge a small amount of steam.
Should the milk dry/caramelise on the
steam wand, simply wrap the wand with
a clean damp cloth, turn the steam wand
over the drip tray and turn the steam on for
approximately 10 seconds (47). With the
cloth still on the steam wand leave to soak
for about 5 minutes and you will find that
after this time the dry/caramelised milk will
easily wipe away. Repeat process if still dirty.

Important: Never clean the steam wand with
an abrasive pad as this will damage the
steam wand.
Should the steam wand become blocked,
supplied with the espresso machine is a
cleaning pin. The cleaning pin is attached to
the cleaning disk located on the inside of the
back door of the espresso machine (49). The
cleaning pin has two pins at each end - one
pin is labelled 'STEAM' and is the longer of
the two. With the cleaning pin insert it into
the hole in the base of the steam nozzle
(48). Should the steam wand remain blocked
unscrew the steam nozzle from the steam
wand. Clean the steam nozzle by once again
using the cleaning pin then flush under
running water.

Cleaning the group head
Deposits of coffee oils build up over time and
affect the taste of the coffee and operation
of the espresso machine. Therefore the
group head will require regular cleaning. It is
recommended that the group head is cleaned
at a minimum every 3 months, this will vary
depending on the frequency of use.

Preparing for the cleaning cycle
1.	 Remove the water reservoir and rinse
clean. To do so, open the door on the
back of the espresso machine (3) and
simply slide out the water reservoir (4).
With fresh water completely fill (5) and
replace the reservoir.
2.	 With the door to the back of the espresso
machine still open remove the cleaning
disc, located on the inside of the back
door (49).

30

Cleaning the group head continued

3.	 Should the group handle be attached to
the group head remove it. Remove the
filter basket and rinse both thoroughly
under running water and set aside.

Note: The lights on the control panel will
continue to chase until the cleaning cycle is
completed, this will take approximately 10
minutes.

4.	 Empty and rinse clean the drip tray,
then place back into position on to the
machine.

Note: During the cleaning cycle all other
espresso machine operations will be locked
until the cleaning cycle is completed. Should
the cleaning cycle be accidentally started
it can be cancelled by switching the power
‘OFF’ at the power outlet.

5.	 Fit the group handle with the double
filter basket (50).
6.	 Position the cleaning disc into the double
filter basket (51).
7.	 Place a Sunbeam Espresso Machine
Cleaning Tablet (EM0020) into the filter
basket that is now also fitted with the
cleaning disc (52) and secure the group
handle to the group head (53) (54).
8.	 Place a sufficiently large container under
both pouring spouts (55).
Starting the cleaning cycle
9.	 Insert the power cord into a 230-240V
AC power outlet and switch the power
‘ON’.
Note: Although the espresso machine is on
at the power outlet ensure that the actual
espresso machine power is ‘OFF’. Therefore
no lights will be illuminated on the espresso
machine control panel.
10.	Simultaneously press and hold down
the single and
double espresso
buttons. While still holding down the
single and
double espresso buttons
briefly press the ‘POWER’ button. As the
lights on the control panel start to chase
from left to right release the single and
double espresso buttons.

11.	When the cleaning cycle is completed
the lights on the control panel will stop
chasing and the espresso machine will
beep 4 times. Following this, the lights
above the 'POWER', 'MANUAL', single
and
double espresso buttons will
come on, signalling that the machine is
ready to use.
12.	Remove the container from under the
pouring spouts and empty.
13.	Remove the group handle from the group
head (56).
14.	Remove the cleaning disc from the group
handle and return to storage position on
the inside of the back door.
15.	Remove the double filter basket from the
group handle and wash in warm soapy
water. Rinse well and dry.
16.	The espresso machine is now ready 	
for use.

31

Descaling
Scale is a surface build up of minerals that
naturally occur over time in all appliances
that are involved with the heating of water.
Therefore the espresso machine will require
occasional descaling. It is recommended
that the espresso machine is descaled every
4-6 months, this will vary depending on the
frequency of use and water hardness.

2.	Should the group handle be attached to
the group head remove it, rinse thoroughly
under running water and set aside.
3.	Using a screwdriver unscrew the brewing
filter/shower screen from the underside of
the group head.
4.	Remove and set aside the filter/screen and
screw in a safe place.

Descaling solution
Use any of the following when descaling the
espresso machine:

Important: Be careful not to lose the
filter/screen and screw once you have
disassembled the group head.

 Sunbeam Espresso Machine Descaling
Tablets (EM0010)

5.	Place a sufficiently large container under
the group head.

 Sunbeam Liquid Descaler (KE0100), or

6.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
Press the ‘POWER’ button once to turn the
espresso machine on.

 Vinegar Solution.
Descaling the espresso machine
Note: Ensure the espresso machine is turned
off and the power cord is unplugged.
1.	Remove the water reservoir and rinse clean.
Depending on the descaling solution being
used use one of the following:
A. Sunbeam Espresso Machine Descaling
Tablets
	 Fill the water reservoir with 1 litre of warm
water and place a descaling tablet into the
reservoir. Once the tablet has dissolved
replace the reservoir, this takes about 5-7
minutes.
B. Sunbeam Liquid Descaler
	 Fill the water reservoir with approximately
1.5 litres of water, add 1 capful of
Sunbeam Liquid Descaler and replace the
reservoir.
C. Vinegar solution
	 Fill the water reservoir with approximately
1.5 litres of warm water, add 3 tablespoons
of vinegar and replace the reservoir.
32

Note: Remember if the ‘POWER’ light
is flashing green this indicates that the
espresso machine is on and is heating up.
When the green light above the ‘POWER’
button stops flashing and turns to a constant
red light this indicates that the espresso
machine is heated and ready to use.
Additionally the lights above the ‘MANUAL’,        
single and
double espresso buttons
will show a constant green light.
7.	Press the ‘MANUAL’ button and allow
half the solution to cycle through the
group head and then once again press the
‘MANUAL’ button to stop the flow.
Important: Do not run descaling solution
through the steam wand.
Note: As a safety mechanism the espresso
machine is programmed to automatically stop
the water flow after 240mls, therefore you
will need to press the ‘MANUAL’ button again
to restart the water flow.

Descaling continued

Note: Depending on the size of the container
under the group head on occasion this may
need to be emptied throughout this process.

13.	Press the ‘MANUAL’ button and allow the
entire water reservoir to cycle through the
group head.

8.	 After half the solution has cycled through
press the ‘MANUAL’ button to stop the
flow and then press the ‘POWER’ button
to turn the machine off.

Note: As a safety mechanism the espresso
machine is programmed to automatically stop
the water flow after 240mls, therefore you
will need to press the ‘MANUAL’ button again
to restart the water flow.

9.	 Leave the machine off for 10-15 minutes
to allow the descaler solution to take
affect.
10.	Press the ‘POWER’ button once to turn
the espresso machine on.
11.	Press the ‘MANUAL’ button and allow the
remaining solution to cycle through the
group head.
12.	Remove the water reservoir from the
machine and rinse thoroughly under
running water, ensuring that all traces
of the descaling solution is removed.
Fill with clean water and replace the
reservoir.

Note: Depending on the size of the container
under the group head on occasion this may
need to be emptied throughout this process.
14.	When this is finished remove the
container under the group head and give
the machine a good wipe over.
15.	Carefully replace the brewing filter/shower
screen to the group head.
Important: Ensure the screw is tightened well.
16.	Fill the water reservoir with fresh water
and position it on to the machine.

33

Advanced programming options
Espresso Thermoblock Temperature
The water temperature of this espresso
machine has been calibrated to the precise
temperature of 92°C at the group head. The
temperature of the water at the group head
can be modified in increments of 2°C up and
down should it be desired.
To do this you need to follow the instructions
below:
1.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
Note: Although the espresso machine is ON
at the power outlet ensure that the actual
espresso machine power is ‘OFF’. Therefore
no lights will be illuminated on the espresso
machine control panel.
2.	Press and hold down the ‘
espresso’ button.

single

3.	While still holding down the ‘ single
espresso’ button briefly press the ‘POWER’
button and release.
Note: This activates the programmability of
the Espresso Thermoblock Temperature and
to signal this, the light above the ‘ single
espresso’ button will illuminate, which is the
factory setting.
-4°C

-2°C

4.	Release the ‘

34

Factory	
Setting

+2°C

+4°C

single espresso’ button.

Note: The light above the ‘ single espresso’
button will remain on and then if you have
already re-programmed the temperature of
the espresso thermoblock the position of the
light will move to one of the other 4 settings
indicating the current temperature setting.
Note: This light will remain on for up to 5
seconds before automatically returning to
the Factory Setting if no action is taken. The
espresso machine will then power on and
begin heating up.
5.	Within 5 seconds press and release one
of the buttons below depending on the
required temperature adjustment;
+2°C = Press the ‘

double cup’ button

+4°C = Press the ‘PROGRAM’ button
-2°C = Press the ‘MANUAL’ button
-4°C = Press the ‘POWER’ button
Note: When you have selected a new
temperature setting the light above the
button pressed will illuminate and to indicate
that the setting has been changed correctly
the light will flash and 2 beeps will sound.
Note: The espresso machine will then
automatically power on and begin heating up.
Remember: If you do not select a new
temperature setting within 5 seconds the
program will return to the Factory Setting and
the espresso machine will then power on and
begin heating up.

Advanced programming options continued

Steam Thermoblock Temperature
The steam temperature of this espresso
machine has been calibrated to deliver a
powerful and dry steam for texturing milk.
The temperature of the steam can be
modified in increments of 5°C up and down
should it be desired.
To do this you need to follow the instructions
below:
1.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
Note: Although the espresso machine is ON
at the power outlet ensure that the actual
espresso machine power is ‘OFF’. Therefore
no lights will be illuminated on the espresso
machine control panel.
2.Press and hold down the ‘
espresso’ button.

double

3.	While still holding down the ‘
double
espresso’ button briefly press the ‘POWER’
button and release.
4.Release the ‘

double espresso’ button.

Note: This activates the programmability of
the Steam Thermoblock Temperature and
to signal this, the light above the ‘ single
espresso’ button will illuminate, which is the
factory setting.
-10°C

-5°C

Factory	
Setting

+5°C

+10°C

Note: The light above the ‘ single espresso’
button will remain on and then if you have
already re-programmed the temperature of
the steam thermoblock the position of the
light will move to one of the other 4 settings
indicating the current temperature setting.
Note: This light will remain on for up to 5
seconds before automatically returning to
the Factory Setting if no action is taken. The
espresso machine will then power on and
begin heating up.
5.	Within 5 seconds press and release one
of the buttons below depending on the
required temperature adjustment;
+5°C = Press the ‘

double cup’ button

+10°C = Press the ‘PROGRAM’ button
-5°C = Press the ‘MANUAL’ button
-10°C = Press the ‘POWER’ button
Note: When you have selected a new
temperature setting the light above the
button pressed will illuminate and to indicate
that the setting has been changed correctly
the light will flash and 2 beeps will sound.
Note: The espresso machine will then
automatically power on and begin heating up.
Remember: If you do not select a new
temperature setting within 5 seconds the
program will return to the Factory Setting and
the espresso machine will then power on and
begin heating up.

35

Advanced programming options continued

Steam Wetness or Steam Pump Rate
The steam pump rate of this espresso
machine has been set at 0.3 seconds on and
0.5 seconds off. Modifying the steam pump
rate enables you to make the steam wetter or
dryer and aids in the delivery of a powerful,
dry steam - ideal for texturing milk. The
steam pump rate (off time) can be modified
in increments of plus or minus 0.1 seconds
should it be desired.
To do this you need to follow the instructions
below:
1.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
Note: Although the espresso machine is ON
at the power outlet ensure that the actual
espresso machine power is ‘OFF’. Therefore
no lights will be illuminated on the espresso
machine control panel.
2.	Press and hold down the ‘PROGRAM’
button.
3.	While still holding down the ‘PROGRAM’
button briefly press the ‘POWER’ button
and release.
4.	Release the ‘PROGRAM’ button.
+0.2 sec	 +0.1 sec	 Factory	
off
off
Setting

-0.1 sec	 -0.2 sec	
off
off

Note: This activates the programmability of
the Steam Pump Rate and to signal this, the
light above the ‘ single espresso’ button
will illuminate, which is the factory setting.

36

Note: The light above the ‘ single espresso’
button will remain on and then if you have
already re-programmed the Steam Pump Rate
the position of the light will move to one of
the other 4 settings indicating the current
setting.
Note: This light will remain on for up to 5
seconds before automatically returning to
the Factory Setting if no action is taken. The
espresso machine will then power on and
begin heating up.
5.	Within 5 seconds press and release one
of the buttons below depending on the
required adjustment;
-0.1 sec = Press the ‘

double cup’ button (wet)

-0.2 sec = Press the ‘PROGRAM’ button (wetter)
+0.1sec = Press the ‘MANUAL’ button (dry)
+0.2 sec = Press the ‘POWER’ button (dryer)
Note: When you have selected a new pump
rate setting the light above the button
pressed will illuminate and to indicate that
the setting has been changed correctly the
light will flash and 2 beeps will sound.
Note: The espresso machine will then
automatically power on and begin heating up.
Remember: If you do not select a new pump
rate setting within 5 seconds the program
will return to the Factory Setting and the
espresso machine will then power on and
begin heating up.

Advanced programming options continued

Factory Reset
To undo any changes made to the program
you can revert back to the original factory
settings.
To do this you need to follow the instructions
below:
1.	Insert the power cord into a 230-240V AC
power outlet and switch the power ‘ON’.
Note: Although the espresso machine is ON
at the power outlet ensure that the actual
espresso machine power is ‘OFF’. Therefore
no lights will be illuminated on the espresso
machine control panel.

Note: This resets ALL the program settings
back to factory settings, including the
program espresso pour volumes, espresso
& steam thermoblock temperatures and the
steam pump rate.
5.	To indicate that you have successfully reset
the factory settings the light above the
‘POWER’ button will flash and 4 beeps will
sound.
Note: The expresso machine will then
automatically power on and begin heating up.

2.	Press and hold down the ‘MANUAL’ button.
3.	While still holding down the ‘MANUAL’
button briefly press the ‘POWER’ button
and release.
4.	Release the ‘MANUAL’ button.

37

Notes

Notes

The Sunbeam
5 Year Pump
Guarantee
Sunbeam has built its reputation
on manufacturing quality electrical
appliances. Our Cafe Series® Espresso
Machine is constructed from the highest
quality materials. So much so, we
guarantee our Espresso Machine pump
for five (5) years against faulty materials
or manufacture. This guarantee is just
another expression of our confidence in
the way we make appliances at Sunbeam.
In order to be eligible for this guarantee,
you must retain your receipt as proof of
purchase.
Your Cafe Series® Espresso Machine is
covered for the first year against faulty
material or manufacture by the Sunbeam
12 Month Repair Guarantee. Should
you experience any difficulties with your
appliance within this 12 Month period,
please phone our customer service line for
advice on 1300 881 861 in Australia, or
0800 786 232 in New Zealand.
The Sunbeam five (5) year pump guarantee
begins from date of purchase and extends
for four years beyond the 12 Month Repair
Guarantee. It covers only the pump,
guaranteeing it against faulty materials
or manufacture. It does not cover damage
caused by accident, misuse or being used
in a manner not in accordance with the
Instruction Book. Similarly, this pump
guarantee does not cover freight or any
other costs incurred in making a claim.

If a fault should develop with the pump
after the period covered by the 12 Month
Repair Guarantee, please call Sunbeam
Customer Service on the number listed
below or send a written claim to Sunbeam
at the address listed below.
On receipt of your claim, Sunbeam
will advise you on how to obtain a
replacement pump if your pump is
defective. Alternatively, you can return the
Cafe Series® Espresso Machine to any of
Sunbeam’s authorised service centres,
together with your receipt. The service
centre will examine the pump and if it
is faulty or defective, the pump will be
replaced free of charge.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:

Sunbeam Corporation Ltd.
Australia
www.sunbeam.com.au

1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia

Sunbeam Corporation Ltd.
New Zealand
www.sunbeam.co.nz

0800 786 232
26 Vestey Drive, Mt Wellington

Auckland, New Zealand
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to
the appliance.
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law and under the New Zealand
Consumer Guarantees Act. In Australia you
are entitled to a replacement or refund for
a major failure and for compensation for
any other reasonably foreseeable loss or
damage. You are also entitled to have the
goods repaired or replaced if the goods fail
to be of acceptable quality and the failure
does not amount to a major failure.
IMPORTANT NOTE
Sunbeam agrees to replace the pump in
the event of the pump developing a fault
or defect, within the four years after the
12 Month Repair Guarantee.
As your Cafe Series® Espresso Machine
needs to be assessed at a Sunbeam
authorised service centre, it will not be
accepted through retail stores.
If using the Cafe Series® Espresso Machine
for commercial use this pump guarantee
is limited to 12 months from the date of
purchase.

12 Month Repair Guarantee
In the unlikely event that this appliance develops any malfunction
within 12 months of purchase due to faulty materials or
manufacture, we will REPAIR it for you free of charge.
Should you experience any difficulties with
your appliance, please contact our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim to
Sunbeam at the address listed below. Upon
receipt of your claim, Sunbeam will seek to
resolve your difficulties or, if the appliance is
defective, advise you on how to arrange for it
to be repaired.
Your Sunbeam 12 Month REPAIR Guarantee
naturally does not cover misuse or improper
handling, and normal wear and tear. Similarly,
your 12 Month REPAIR Guarantee does not
cover freight or any other costs incurred in
making a claim.
It will be at the discretion of Sunbeam whether
to repair or replace any appliance that develops
a malfunction during the REPAIR Guarantee
period. Sunbeam is by no means obliged to
replace any appliance if it can be repaired. 	
If the appliance is irreparable due to any
claimed defect caused by faulty workmanship
or material, then Sunbeam will replace the
appliance.
Prior to any repairs being undertaken, a
purchase receipt must be provided as proof of
purchase. Sunbeam will not be responsible for
the cost of transport to and from any Sunbeam
authorized service centre, or any insurance
costs associated with this transport. Similarly
Sunbeam will not be responsible for any
damage or loss that occurs during transit to or
from any Sunbeam authorized service centre
for reasons not related to the malfunction.  

The benefits given to you by this guarantee are
in addition to your other rights and remedies
under any laws which relate to the appliance.
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
In Australia you are entitled to a replacement
or refund for a major failure and for
compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality
and the failure does amount 	
to a major failure.
Should your appliance require repair or service
after the guarantee period, contact your
nearest Sunbeam service centre.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:

Australia
www.sunbeam.com.au

1300 881 861
Units 5 & 6, 13 Lord Street	
Botany NSW 2019 Australia
New Zealand
www.sunbeam.co.nz

0800 786 232
26 Vestey Drive, Mt Wellington 	
Auckland, New Zealand

Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Visit www.sunbeam.com.au

Or call 1300 881 861
In New Zealand
Visit www.sunbeam.co.nz

Or call 0800 786 232

	

is a registered trademark.

‘Cafe Series’ is a trademark of Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2006.
ABN 45 000 006 771

Sunbeam Corporation is a division of GUD Holdings Ltd.
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.

08/11



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Create Date                     : 2013:04:19 15:30:25Z
Keywords                        : manuals, instruction manuals, user manuals, service manuals, user guides, pdf manuals, owners manuals, installation guides
Modify Date                     : 2014:12:07 13:34:58+08:00
Subject                         : Search through 700.000 manuals online & and download pdf manuals.
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Description                     : Search through 700.000 manuals online & and download pdf manuals.
Title                           : ManualsLib - Makes it easy to find manuals online!
Creator Tool                    : pdftk 1.44 - www.pdftk.com
Metadata Date                   : 2014:12:07 13:34:58+08:00
Producer                        : itext-paulo-155 (itextpdf.sf.net-lowagie.com)
Document ID                     : uuid:7993edee-6b60-5946-ae8a-56ba9bc192a6
Instance ID                     : uuid:7d0d6f3a-2042-bd49-9d96-b391dbc580f2
Page Count                      : 44

EXIF Metadata provided by EXIF.tools