Sunrex Technology EBT203A Bluetooth Touchpad User Manual EBT 203A Manual

Download:
Mirror Download [FCC.gov]
Document ID	1863011
Application ID	iAjxtz07gMlqUMmrJ0T+Ug==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.16kB (39537 bits)
Date Submitted	2012-12-19 00:00:00
Date Available	2012-12-19 00:00:00
Creation Date	2012-12-10 14:02:42
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2012-12-10 14:02:42
Document Title	Microsoft Word - EBT-203A_Manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Daphne

Bluetooth Touchpad
(EBT-203A / KST-S01BT / 19025)
User Manual
Important Information
For Windows® 8 operating system, you can use the keyboard immediately after
plugging the dongle (receiver) into the USB port.
Hardware Installation
1. Make sure the batteries of the keyboard is installed correctly. Please follow the
polarity signs in the battery compartment.
2. Please make sure the power switch on the back of the Touchpad is switched to
“ON” before using the Touchpad. When not in use, please turn the power switch
to “OFF” for power saving.
ID Pairing Procedure
• Now the radio connection between computer and Touchpad must beestablished
(Pairing). Press the keys “ Left Button + Right Button” and Power ON your
Touchpad simultaneously.
After 2 seconds pairing starts, the pairing LED is blinking.
Pairing can take several seconds and is finished, when the LED above
the trackball goes off.
Should the pairing process break off (LED goes off) without getting a
connection, try it again. Probably, it can be necassary to switch the rear
sliding switch off and on again.
• On your screen the Bluetooth assistent opens and shows
all Bluetooth devices, which are located near your computer.
Select your Touchpad and confirm with „Continue“.
• The Touchpad is still not identified, press „Continue“.
Note:
-Make sure your PC is ON and running when doing the pairing procedure.
-You don’t have to pair ID again after changing batteries. If it can’t work, please follow
the steps above to pair ID.
Import Usage Information
‹ Battery:
1. We recommend using alkaline batteries for a longer battery life.
2. Don’t mix different types of batteries or new and old batteries together. Always
replaced old batteries with new and same type batteries.
3. Remove batteries after long periods of non-use. Battery leakage or corrosion may
damage the device quality and cause danger.
‹ Rating:
Keyboard: 3VDC 35mA
‹
Max. operating temperature: 40∘C
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Notice
Operation is subject to the following two conditions: (1) this device may
not cause interference and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2012:12:10 14:02:42+08:00
Create Date                     : 2012:12:10 14:02:42+08:00
Format                          : application/pdf
Title                           : Microsoft Word - EBT-203A_Manual.doc
Creator                         : Daphne
Document ID                     : uuid:9e4cadb7-1b40-40d3-85a0-6f265206f27b
Instance ID                     : uuid:d7ea721b-4813-44dc-8faa-b99f71de5eff
Page Count                      : 3
Author                          : Daphne

EXIF Metadata provided by EXIF.tools