Superior Electronics 4131SPKQ SPLIT-SERIES KEYPAD User Manual
Superior Electronics Corporation SPLIT-SERIES KEYPAD
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3251450 |
| Application ID | ca3dP59J9OV26SMDh8sN2g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 86.27kB (1078338 bits) |
| Date Submitted | 2017-01-09 00:00:00 |
| Date Available | 2017-01-09 00:00:00 |
| Creation Date | 2016-12-20 13:47:13 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-01-05 11:26:57 |
| Document Title | User Manual |
| Document Creator | Acrobat PDFMaker 15 for Word |
| Document Author: | Robert Mattern |
Split Series Keypad with
Proximity Card Reader
Manual
⢠Split series installation for added
security
⢠Up to 1,000 possible user codes
and/or proximity cards
⢠12~24 VDC Operation, auto-adjusting
⢠Tamper output
⢠Keypad illuminates when a button is
pressed
ENFORCER Split Series Keypad with Proximity Card Reader
Quick Installation Guide:
This page is for installers looking to do a basic installation and programming of the keypad. For
more in-depth installation and programming instructions, see the Table of Contents on page 4.
Mounting Diagram:
Keypad
Mounting
screws
Controller
Installation
screws
Mounting screws
Quick Wiring Diagram:
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Quick Programming Guide:
This page is for installers looking to do a basic installation and programming of the keypad. For
more in-depth installation and programming instructions, see the Table of Contents on page 4.
Programming Tips
⢠The master, super user, common user, visitor, duress, and user codes cannot be the
same.
⢠A flashing amber LED indicates the keypad is in standby mode. A solid amber LED indicates
the keypad is in programming mode.
⢠If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see page 28).
Programming Instructions
Follow the instructions bellow if the following covers your needs.
â˘
â˘
â˘
â˘
A new master code.
A single 4-digit user code for all users, and no proximity cards
One output to unlock a door.
A 3-second delay time in opening the door after the output is activated.
1. Power on the keypad and controller.
2. Turn off the beeping before the 1-minute power-up period ends:
3. Move the link-up jumper to the ON position.
4. Enter Programming Mode:
NOTE: is the default master code.
5. Change the master code:
NOTE: is the new master code.
6. Set the user code to operate output #1 (unlock the door):
NOTE: chooses user ID #000 of 1,000 possible users (000~999).
is the new user code for user ID #000.
7. Set the output #1 delay time (skip this step if the default value of 5 seconds is
acceptable):
NOTE: sets the output #1 delay time for 3 seconds.
8. Exit Programming Mode:
9. Move the link-up jumper to the OFF position.
NOTE: The link-up procedure must be done during initial programming and any time
a.
the master code is changed.
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Table of Contents:
Quick Installation Guide .................................................................................................................... 2
Mounting Diagram ............................................................................................................................ 2
Quick Wiring Diagram ....................................................................................................................... 2
Quick Programming Guide ............................................................................................................... 3
Table of Contents ............................................................................................................................. 4
Features ........................................................................................................................................... 5
Specifications ................................................................................................................................... 5
Dimensions ....................................................................................................................................... 6
Parts List ........................................................................................................................................... 6
Installation ........................................................................................................................................ 6
LED Indicators and Sounds .............................................................................................................. 7
Important Notes ................................................................................................................................ 8
Wiring Diagram â Keypad ................................................................................................................. 8
Wiring Diagram â Controller ............................................................................................................. 9
Sample Applications ................................................................................................................. 10~11
Sample Applications for Auxiliary Terminals ............................................................................ 12~13
Getting Ready to Program ........................................................................................................ 14~15
Programming Format and Default Programming Values ................................................................ 16
System Restore .............................................................................................................................. 17
Programming the Master Code ...................................................................................................... 17
Programming the Super User Code ......................................................................................... 18~19
Programming Common User Codes ........................................................................................ 19~20
Programming User Codes and Proximity Cards ....................................................................... 20~21
Programming Visitor Codes for Output #1 ...................................................................................... 22
Programming Duress Codes .................................................................................................... 23~24
Programming the Output Mode and Output Timing ........................................................................ 25
Programming the Real-Time Clock ................................................................................................ 26
Programming the Output #1 Auto-Disable Time ....................................................................... 26~27
Programming the Wrong-Code System Lock-Up ........................................................................... 28
Programming the User Code Entry Mode ...................................................................................... 28
Programming the Keypad Sounds .................................................................................................. 29
Programming the Output Relay Activation Sounds ........................................................................ 29
Programming the Amber LED Flashing during Standby Mode ....................................................... 30
Programming the Door-Forced-Open Warning and Timing ............................................................ 30
Programming the Door-Propped-Open Warning and Delay Time .................................................. 31
Programming the Door Open Alarm and Timing ............................................................................ 31
Programming the Egress Delay/Warning/Alarm ....................................................................... 32~33
Direct Access to Programming (DAP) ............................................................................................ 34
Userâs Guide to Operating the SK-4131-SPSQ .............................................................................. 35
Notes .............................................................................................................................................. 36
Also Available ................................................................................................................................. 36
Warranty ......................................................................................................................................... 36
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Features:
⢠Split series installation for added security
⢠12~24 VDC Auto-adjusting operation
⢠Up to 1,000 possible user codes (000~999) and/or
proximity cards for output #1, 100 (001~100) for
output #2, 100 (001~100) for output #3
⢠Up to 50 (01~50) possible temporary visitor
codes, which can be programmed for
one-time or limited-time use (1~99 hours)
⢠Output #1: Form C relay, 5A@24VDC max.
⢠Output #2: Form C relay, 1A@24VDC max.
⢠Output #3: Form C relay, 1A@24VDC max.
⢠Outputs #1, #2, and #3 can be programmed to
activate for up to 99,999 seconds
(nearly 28 hours)
⢠Tamper output: N.C. Dry contact,
50mA@24VDC max.
⢠Keypad illuminates when a button is pressed;
backlight can be programmable for FULL or
AUTO in standby mode
⢠Built-in door chime
⢠Built in current limited (750mA) power source for
keypad for added security
⢠Keypad active, alarm, duress, and interlock
output: Transistor ground, 100mA@24VDC max.
⢠Keypad mounts to a standard single-gang back
box (surface-mount back box included)
⢠All features are programmed directly from the
keypad: No need for an external programmer
⢠EEPROM Memory protects programmed
information in case of power loss
⢠Up to 50 (01~50) duress codes for output #1, 10
(01~09) for output #2, 10 (01~09) for output #3
⢠Programmable egress input with optional warning
alarm and delayed egress
⢠Door sensor input for anti-tailgating operation
⢠Interlocking input for connecting to a second
keypad for mantrap applications
⢠Simple three wire connection between keypad
and controller
Specifications:
Operating voltage
Standby
Keypress
Output 1 active
Current draw
(at 12VDC)
Output 1 & 2 active
Output 1, 2, & 3 active
Total max current draw
#1âForm C
#2âForm C
#3âForm C
Alarm
Outputs
Key active
Duress
Interlock
Tamper
Egress
Door sensor
Inputs
Door inhibit
Doorbell
Tamper
Proximity reader frequency
Proximity reader sensing distance
Operating temperature
Operating humidity
Keypad
Dimensions
Controller
Keypad
Weight
Controller
SECO-LARM U.S.A., Inc.
12~24 VDC
88mA
115mA
115mA
128mA
138mA
220mA
5A@24VDC
1A@24VDC
1A@24VDC
100mA@24VDC
100mA@24VDC
100mA@24VDC
100mA@24VDC
50mA@24VDC
N.O. Ground
N.C. Ground
N.O. Ground
N.O. Ground
N.C. Ground
125kHz (EM125)
11/2" (38mm)
-4°~158°F (-20°~70°C)
5~95% (non-condensing)
45/8"x27/8"x11/2" (117x73x38 mm)
37/16"x43/4"x11/4" (87x120x32 mm)
6.3-oz (180g)
8.8-oz (250g)
ENFORCER Split Series Keypad with Proximity Card Reader
Dimensions:
Keypad
Controller
45/8"
(117mm)
37/16"
(87mm)
27/8"
(73mm)
11/2"
(38mm)
43/4"
(120mm)
11/4" (32mm)
Parts List:
1x Keypad
2x Installation screws
2x Diodes
1x Keypad back box
5x Mounting screws
1x Manual
1x Controller
5x Mounting screw anchors
Installation:
Keypad (SK-4131-SPKQ)
1.
2.
3.
4.
5.
6.
Find a suitable location to mount the keypad. Install it at the height at which most users will be
able to easily operate the keypad.
Install one mounting screw on the wall. After the screw has been installed, hang the back box
by the top mounting hole.
Install the second mounting screw through the button hole.
Run the wire through the wall or conduit from the controller to the back box location, then run
the wire through the back box.
Refer to the wiring diagram on pages 8~9 and connect the wires.
Finish assembly by attaching the keypad to the back box with the included screws.
Controller (SK-4131-SPCQ)
1.
2.
3.
4.
5.
Find a suitable location to mount the controller. Install it where it is secure and only accessible
by authorized personnel.
Using the included mounting screws, install the controller on the wall.
Remove the cover using a screwdriver. Run wires through the wall or conduit to the controller.
Refer to the wiring diagram on pages 8~9 and connect the wires.
Finish assembly by reattaching the cover and cover screws.
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
LED Indicators and Sounds:
LED Indicators â Keypad
Green/Red (Left)
Available for free
connection (Green)
Steady
Keypad locked (Red)
Output #1 inhibited (Red)
Flashing
Inhibit mode paused (Red)
Amber LED (Center)
Green/Red LED (Right)
Programming mode
Output #1 activated (Green)
Output #2 activated (Red)
Standby mode
LED Indicators â Controller
Flashing
1 Flash per second
Keypad Sounds and LEDs
Status
In programming mode
Successful key entry
Successful code/card entry
Unsuccessful code/card entry
Power up delay
Output relay activation (2)
In standby mode (3)
System restore mode
Code / card already stored
Real time clock stopped after
power loss
Keypad link-up with
controller failed
Amber LED
Power-up mode
In standby or programming mode
Sounds (1)
1 Beep
2 Beeps
5 Beeps
Continuous beeping for
1 minute
1-Sec long beep
2 Beeps
1 Long beep
Continuous 3 fast beeps
every 5 seconds
Continuous beep
every 1.5 seconds
Amber LED (Center)
Steady ON
1 Flash
2 Flashes
5 Flashes
Continuous flashing for
1 minute
1 Flash/sec
Fast flashing for 2.5 min
NOTE:
1. Keypad sounds can be programmed ON or OFF (see page 29).
2. Output relay activation sounds can be programmed ON or OFF (see page 29).
3. Amber LED flashing during standby mode can be programmed ON or OFF
(see page 30).
Controller Sounds and LEDs
Status
In programming mode
In standby mode
Power up delay
Egress delay warning
Door propped-open warning
Door forced-open warning
SECO-LARM U.S.A., Inc.
Sounds
Continuous beeping for
5 seconds and doorbell
Continuous beeping
Continuous beeping
Continuous beeping and alarm output
Amber LED (Center)
1 Flash/sec
1 Flash/sec
Continuous flashing
for 5 seconds
ENFORCER Split Series Keypad with Proximity Card Reader
IMPORTANT NOTES:
IF USING THE KEYPAD WITH A MECHANICALLY OPERATED
DOOR OR GATE, MOUNT THE KEYPAD AT LEAST 15â (5m)
FROM THE DOOR OR GATE TO PREVENT USERS FROM
BEING CRUSHED OR PINNED. FAILURE TO DO SO MAY
RESULT IN SERIOUS INJURY OR DEATH.
1.
2.
3.
4.
Always disconnect power before servicing the keypad. Do not apply power until all
connection wiring is completed.
The keypad must be properly grounded. Use a minimum 22AWG wire connected to the
common ground output. Failure to do so may damage the keypad.
All wiring and programming should be done by a professional installer to reduce the risk of
improper installation.
The userâs guide for this keypad is located on page 35 of this manual. Be sure to store this
manual in a safe place for future reference.
Wiring Diagram â Keypad:
Connection Terminals
Terminals
12~24 VDC
Data I/O
Tamper N.C.
Aux LED
Jumper Settings
Jumper
Position
Full
Backlit
Auto
Description
Connect to controllerâs keypad power terminal.
Connect to controllerâs GND (-) terminal.
Connect to controllerâs Data I/O terminal.
Tamper switch output, N.C. contact, max. 50mA@24VDC. Connect to N.C.
24-hour protection zone of an alarm if needed.
Connect to trigger the left green LED.
Description
Dim backlit during standby. Full backlit for 10 seconds after any button press.
No backlit during standby. Full backlit for 10 seconds after any button press.
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Wiring Diagram â Controller:
12~24V DC
GND (â)
KEYPAD PWR
DATA I/O
EG IN
DOORBELL IN
DU OUT
INT. LOCK
O/P 1 INHIB
DOOR SENS
COM
N.O.
N.C.
COM
N.O.
N.C.
COM
N.O.
KEY ACT O/P
ALARM O/P
Egress Input
Doorbell Input
Duress Output
Interlock Output
Output #1
Inhibit
10
Door Sensor
11
GND (â)
12
Tamper
13
20
21
SECO-LARM U.S.A., Inc.
Output 3
19
Output 2
14
15
16
17
18
Output 1
OUTPUT 1 OUTPUT 2 OUTPUT 3
GND (â)
TAMPER
N.C.
Connection Terminals
Terminals
1 12~24 VDC
2 GND (â)
3 Keypad PWR
4 Data I/O
N.C.
COM
N.O.
N.C.
COM
N.O.
N.C.
COM
N.O.
22
Key Active
Output
23
Alarm Output
Description
Connect to a 12~24VDC power supply.
Observe polarity.
Connect to keypadâs positive (+) terminal.
Connect to keypadâs Data I/O terminal.
N.O. Pushbutton contact to ground. Press
button to Activate output #1.
N.O. Doorbell contact to ground.
Transistor ground, max. 100mA@24VDC.
Triggers a silent alarm or other device when the
user enters a duress code.
Transistor ground, max. 100mA@24VDC or
connect to Output #1. Inhibit of second keypad
if needed so that if one keypad is used to open
a door, the other is disabled.
Output #1 inhibitor. N.O. input, connect to
Interlock Control of second keypad if needed so
that if one keypad is used to open a door, the
other is temporarily disabled.
Connect to an optional N.C. sensor such as a
magnetic contact to monitor if a door is open or
closed. Connect to ground if not used.
Common ground output.
Tamper-switch output, N.C. contact, max.
50mA@24VDC. Connect to the N.C. 24-hour
protection zone of an alarm if needed.
Output #1, NO/NC/COM, relay output, max
5A@24VDC
Output #2, NO/NC/COM, relay output, max
1A@24VDC
Output #3, NO/NC/COM, relay output, max
1A@24VDC
Transistor ground max. 100mA@24VDC.
Switches to ground (â) for 10 seconds after any
button pressed.
Transistor ground max. 100mA@24VDC.
Switches to ground when alarm output
activated, connect to an optional auxiliary alarm.
ENFORCER Split Series Keypad with Proximity Card Reader
Sample Applications:
Stand-Alone Door Lock:
In this application, the keypad is connected to a single door lock and an egress pushbutton.
10
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Sample Applications (continued):
Interlock system using two Split-Series Keypads:
In this application, two keypads are each connected to separate door locks and egress
pushbuttons. While one door is open, the other cannot be opened.
⢠Use an N.C. magnetic contact or some other N.C. device to detect whether a door is opened
or closed. Do this for the two doors being protected.
Digital Keypad
Digital Keypad
Egress button
Door bell
button
Egress button
Door bell
button
Door 1
sensing
Door 2
sensing
Common Ground
Cross wire connection for inter-lock functions
An interlock system needs two door controllers. This application example uses two keypad
systems with simple cross wire connection on their "Output 1 Inhibit" and "Interlock Control
Output" terminals. It is necessary to link up the "(â) GND" terminals of the two keypads as
common ground to achieve the inter-lock functions.
â˘
â˘
â˘
â˘
Use keypad to open the door from outside
Press egress button to open the door from inside
Connect the door magnetic sensors on the doors to monitor their positions
While door 1 is open, door 2 cannot be opened, and vice versa
SECO-LARM U.S.A., Inc.
11
ENFORCER Split Series Keypad with Proximity Card Reader
Sample Applications for Auxiliary Terminals:
Door Sensor:
â˘
â˘
â˘
With the help of a Normally Closed
door position sensor (usually a
magnetic door switch) on the door
to set up the following functions:
â˘
â˘
Door Auto Relock â The system will immediately
relock the door after the door is closed. This
prevents unwanted "tailgate" entries, which can
happen if an unauthorized person tries to follow an
authorized person through the door.
Interlock Control â When the door is open, the
Interlock Output will give a (-) ground command to
disable the other keypad in an interlock system
Door Forced-Open Warning â The keypad will
beep and the controller will beep, activate the
alarm output, and activate the siren whenever the
door is forced open without using a valid user
code. See "programming the Door-Forced Open
Warning and Timing" on page 30.
Door Propped-Open Warning â The keypad will
beep whenever the door is open longer than the
programmed time. See "Programming the DoorPropped-Open Warning and Timing" on page 31.
Door Open Alarm â The controller will activate the
alarm output and siren whenever the door is
opened. See "Programming the Door Open Alarm
and Timing" on page 31.
22 23
22 23
11
11
Alarm Output:
The Alarm Output switches to (â) ground in door forced to open or the door open after Egress
Delay. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard; or
connect it to a 24 hour Normally Open protection zone of an alarm system. See "Programming
the Door-Forced-Open Warming and Timing" and "Programming the Door Open Alarm and
Timing" on pages 30~31.
NOTE: Only one connection option is recommended. Make sure that the sink current does not
exceed the maximum rating of 100mA.
12
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Sample Applications for Auxiliary Terminals (continued):
Key Active Output:
The Key Active Output switches to (â) ground for 10 seconds whenever a key is touched. You
may use it to turn ON an LED lamp and for a small buzzer to notify a guard, or to energize a
relay to switch ON lights or trigger a CCTV Camera to start recording.
NOTE:
⢠Make sure that the relay for switching ON lights has high enough isolation between high
voltage and low voltage to prevent damage of the keypad.
⢠Only one connection option is recommended. Make sure the sink current does not exceed
the maximum rating of 100mA.
⢠External power supply and isolation relay are strictly necessary in driving high power
device, such as lights.
Duress Output:
The Duress Output switches to (â) ground when a duress code is entered. You may use it to
turn ON an LED lamp and/ or a small buzzer to notify a guard; or connect it to a 24 hour
Normally Open protection zone of an alarm system.
NOTE: Only one connection option is recommended. Make sure that the sink current does not
exceed the maximum rating of 100mA.
SECO-LARM U.S.A., Inc.
13
ENFORCER Split Series Keypad with Proximity Card Reader
Getting Ready to Program:
Code and/or Cards:
The SK-4131-SPSQ can be set to be activated by users in one of three ways:
1.
2.
3.
Keypad code only â There are five types of keypad codes:
⢠Master code â Used only for entering programming mode; there can be only one master
code per keypad.
⢠Super user code â Can be used to activate outputs #1, #2, and #3, or to disable (inhibit)
or enable the operation of output #1.
⢠User codes â Unique codes for each user to activate outputs #1, #2, or #3.
⢠Visitor codes â Temporary user codes that can be assigned to visitors or temporary
workers to activate output #1; the visitor codes can be programmed for one-time use or
to expire after a set number of hours has passed.
⢠Duress codes â Assigned to specific users as a way to send a silent alert if forced to use
the keypad under duress.
Proximity card only â Standard 125kHz (EM125) proximity cards can be used to activate
output #1, output #2, or output #3.
Card + code â For enhanced security, the user can be required to also enter a code after
tapping a proximity card. The code may be unique to each card or to a group of users, or a
common code can be used with all cards.
Security Levels:
There are four possible security levels for the SK-4131-SPSQ:
1.
2.
3.
4.
Card only â The most basic, convenient level of security. Hold a previously-programmed
proximity card over the keypad to activate outputs #1, #2, or #3 (see "Programming User
Codes and Proximity Cards" on pages 20~21).
User code only â Type in a 4- to 8-digit user code to activate outputs #1, #2, or #3
(see pages 20~21).
Card + Common user code â All valid proximity cards can be programmed with a single
common user code so that outputs #1, #2, or #3 can only be activated if one of the cards and
the common user code are used together. The common user code is automatically assigned
when each proximity card is programmed into the keypad (see "Programming Common User
Codes" on pages 19~20).
Card + Unique user code â The most secure level. Each proximity card can be programmed
with its own unique user code so that outputs #1, #2, or #3 can only be activated if the card
and the unique code are used together (see pages 20~21).
Power up the Keypad:
When the keypad is first powered up, it will beep continuously for about 1 minute. During this
power-up time, if needed, use Direct Access to Programming (DAP) to reset the master code
(see "Direct Access to Programming (DAP)" on page 34).
1.
Turn off the beeping before the 1-minute powered-up period ends:
This will immediately stop the beeping.
When this beeping has ended, the keypad is ready for normal operation or for programming.
14
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Getting Ready to Program (continued):
Enter and Exit Programming Mode:
All programming of the keypad is done in programming mode.
1.
Enter the programming mode:
NOTE: is the master code. is the default master code (see
2.
"Programming the Master Code" on page 17 to program a new master code). The
amber LED will turn to a steady ON to indicate that the keypad is in programming
mode.
Exit programming mode:
The
entry can be used to exit programming mode at any time while programming.
The keypadâs amber LED will return to flashing, indicating standby mode, upon exiting
programming mode.
NOTE: DO NOT DISCONNECT THE KEYPAD FROM POWER WHILE IN
PROGRAMMING MODE. Disconnecting the keypad while in programming mode
could cause a keypad memory error.
Linking the Keypad and Controller:
The keypad and controller must be linked prior to initial programming.
1.
Enter the programming mode:
2.
3.
Move the link-up jumper on the controller to the ON position.
Exit programming mode:
4.
Move the link-up jumper on the controller back to the OFF position.
NOTE: The link-up procedure must be done during initial programming and any time the
master code is changed.
SECO-LARM U.S.A., Inc.
15
ENFORCER Split Series Keypad with Proximity Card Reader
Programming Format and Default Programming Values:
In this manual, the format used for programming the keypad is as follows:
A 2 digit () FUNCTION identifier to tell the keypad what is being programmed.
A varying number of digits () to represent the parameters of this FUNCTION.
The ( ) key to confirm programming of the FUNCTION.
â˘
â˘
â˘
The following is a list of different programming functions:
Function
01
02
03
04
05
10
20
30
40
41
42
43
51
52
53
55
56
60
70
71
72
73
80
81
90
91
Parameters
Master code
Super user code
Common user code for output #1
Common user code for output #2
Common user code for output #3
User codes/cards for output #1
User codes/cards for output #2
User codes/cards for output #3
Visitor codes for output #1
Duress codes for output #1
Duress codes for output #2
Duress codes for output #3
Output mode for output #1
Output mode for output #2
Output mode for output #3
System real-time clock
Output #1 auto-disable time
Wrong-code system lock-up
User code entry mode
Keypad sounds
Output relay activation sounds
Amber LED standby flashing
Door-forced-open warning
Door-propped-open warning
Egress delay/warning/alarm
Door open alarm and timing
Default functions and values
Default 0000, code length from 4~8 digits
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
No default, must be programmed
5-Second output, momentary
5-Second output, momentary
5-Second output, momentary
No default, must be programmed
No default, must be programmed
Locks keypad after 10 false code/card tries
Manual entry of "#" after each code
Programming and operation beeps enabled
1-Second beep when output is activated
Amber LED flashes on standby
Warning disabled
Warning disabled
Egress output happens immediately
Alarm output is disabled
Page #
17
18~19
19~20
19~20
19~20
20~21
20~21
20~21
22
23~24
23~24
23~24
25
25
25
26
26~27
28
28
29
29
30
30
31
32~33
31
NOTE: The Direct Access to Programming (DAP) code 2828 (page 34) and the system restore
code (page 17) are fixed and cannot be changed, even via programming.
16
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
System Restore:
System restore will reset all programming values except the master code back to the default values
shown on page 16.
1.
2.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode" on
page 15).
Initiate system restore:
NOTE:
⢠System restore will reset ALL programming except the master code back to default values. Be
careful to use system restore only when absolutely necessary.
⢠System restore may take several minutes. The amber LED will flash rapidly during this time.
⢠Once system restore has been completed, the keypad will beep twice to show that all
programming values have been reset to their default values and are ready to be
re-programmed.
⢠At this point, the keypad is still in programming mode.
Programming the Master Code:
The master code is used to enter programming mode. The master code does not serve as a user
code for activating outputs #1, #2, or #3.
1.
2.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode" on
page 15).
Enter new master code:
NOTE:
â˘
â˘
â˘
â˘
â˘
â˘
â˘
represents the new master code, which can be 4 to 8 digits long.
There can be only one master code for the keypad.
Programming a new master code will overwrite the previous master code.
If the master code is forgotten, use Direct Access to Programming (DAP) to reset the master
code (see page 34).
The master, super user, common user, visitor, duress, and user codes cannot be the
same.
If the keypad is set for Auto Code Entry Mode, user codes will need to be the same
number of digits as the master code (see "Programming the User Code Entry Mode" on
page 28).
It is recommended to re-link the keypad and controller immediately after changing the master
code. If the link-up procedure is not performed after changing the master code then the
keypad will beep once every second until the keypad and controller are re-linked (see
"Linking the Keypad and Controller" on page 15).
SECO-LARM U.S.A., Inc.
17
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Super User Code:
The super user code has multiple functions:
â˘
â˘
â˘
â˘
â˘
The super user code can activate or deactivate output #1, output #2, and
output #3 at any time.
The super user code can toggle operation of output #1 on or off.
The super user code can pause or restart the timed output #1 auto-disable period.
The super user code can enable or disable output #1.
The super user code is exempt from any system inhibition or lockup functions. It is
valid at any time.
Programming the Super User Code:
1.
2.
Make sure the keypad is in programming mode (see "Enter and Exit Programming Mode" on
page 15).
Enter the new super user code:
NOTE:
⢠represents the new super user code, which can be 4 to 8 digits long.
⢠There can be only one super user code for the keypad.
⢠Programming a new super user code will overwrite the previous super user code.
⢠The master, super user, common user, visitor, duress, and user codes cannot be
the same.
Deleting the Super User Code:
This function is useful for protecting the premises in case the super user code is forgotten.
To delete a super user code:
1.
2.
Make sure the keypad is in programming mode (see page 15).
Enter:
Using the Super User Code:
In these examples, assume the super user code is .
1.
Activate or deactivate output #1 (timed or toggle, depending on programming):
2.
Activate or deactivate output #2 (timed or toggle, depending on programming):
3.
Activate or deactivate output #3 (timed or toggle, depending on programming):
18
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Super User Code (continued):
4.
Toggle operation of output #1 ON or OFF.
NOTE:
⢠This function is used to leave output #1 active for extended periods of time.
⢠Do not forget to deactivate this function after its use is no longer required.
⢠It is recommended to only use this function with fail-safe locks.
⢠All functions requiring use of the door sensor input are suspended while this function is
in use.
5.
Temporarily pause or restart the timed output #1 auto-disable period:
NOTE:
⢠This function is used to enable the operation of output #1 if it was disabled using the
output #1 auto-disable function (see pages 26~27).
⢠When the output #1 auto-disable function is inactive, the left red LED will flash steadily.
This indicates that output #1 may now be used.
6.
Disable or enable output #1 (toggle, regardless of programming):
NOTE:
⢠For more information on programming timed or toggle mode, see "Programming the
Output Mode and Output Timing" on page 25.
⢠The left LED will remain red while output #1 is disabled.
⢠For safety reasons, the egress button works regardless of whether output #1 is enabled
or disabled via the super user code.
⢠The super user code continues to operate output #1 even while that output is disabled.
Programming Common User Codes:
This function allows a common user code to be automatically added to each proximity card as it is
programmed. Every proximity card user also uses the same common user code to operate
outputs #1, #2, or #3. This provides greater security than programming the keypad to operate with
the card alone. It is also more convenient than assigning each user a unique user code, although
unique user codes offer an even greater degree of security.
1.
To program a common user code for output #1:
2.
To program a common user code for output #2:
3.
To program a common user code for output #3:
SECO-LARM U.S.A., Inc.
19
ENFORCER Split Series Keypad with Proximity Card Reader
Programming Common User Codes (continued):
NOTE:
â˘
â˘
â˘
â˘
represents the new common user code, which can be 4 to 8 digits long.
Programming a new common user code will overwrite the previous common user code.
A common user code is not necessary if unique user codes are assigned.
The master, super user, common user, visitor, duress, and user codes cannot be the
same.
Programming User Codes and Proximity Cards:
When programming user codes and/or proximity cards, use this general formula:
â Output
â Security Level (or , to delete a user code or card)
â User ID
â User Code/Proximity Card
Outputs:
â˘
â˘
â˘
â Output #1, up to 1,000 possible user codes and proximity cards.
â Output #2, up to 100 possible user codes and proximity cards.
â Output #3, up to 100 possible user codes and proximity cards.
Security Levels and Card/Code Deletion:
There are four possible security levels for the SK-4131-SPSQ:
⢠â Card only â The most basic, convenient level of security. Just tap a
previously-programmed proximity card over the keypad to activate outputs #1, #2, or #3.
NOTE: The duress code feature cannot be used with the keypad programmed to the "card
only" security mode. However, a duress code can be entered instead of a card.
â˘
â˘
â˘
â˘
â˘
20
â User code only â Type a 4 to 8-digit user code to activate outputs #1, #2, or #3.
â Card + Unique user code â The most secure level. This code is programmed
separately for each card and can be unique to the card, or the same code can be used for a
group or department. The card and code must be used together to operate the output.
â Card + Common user code â All valid proximity cards can be programmed with a single
common user code so that outputs #1, #2, or #3 can only be activated if one of the cards and
the common user code are used together. The common user code is automatically assigned
as each proximity card is programmed into a keypad.
â Delete a programmed proximity card or code.
â Delete all programmed proximity cards or codes for the selected output.
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming User Codes and Proximity Cards (continued):
User IDs:
â˘
â˘
to â 1,000 unique user IDs for user codes and prox cards for output #1.
to â 100 unique user IDs for user codes and prox cards for output #2
or output #3.
User Codes:
⢠A user code can be 4 to 8 digits long, and must have the same length as all other codes if
the keypad is used in auto code entry mode (see page 28).
⢠The master, super user, common user, visitor, duress, and user codes cannot be
the same.
Examples:
1. Program only a proximity card for user ID #017 for output #1:
READ CARD
2.
Program a user code for user ID #010 for output #1:
3.
Delete a proximity card for output #1:
4.
READ CARD
Delete code or proximity card for user ID #002 for output #1:
5.
Delete all users for output #1:
6.
Program a proximity card for user ID #001 for output #1 for use with a common user code:
READ CARD
NOTE: A common user code must already be programmed to the output
(see pages 19~20).
7.
Program a proximity card for user ID #023 for output #2 for use with unique user code:
READ CARD
SECO-LARM U.S.A., Inc.
21
ENFORCER Split Series Keypad with Proximity Card Reader
Programming Visitor Codes for Output #1:
Visitor codes are temporary codes that expire after use or after a specified amount of time has
elapsed. While active, they operate output #1 as normal user codes.
FIRE
NOTE:
⢠Visitor codes cannot be used to deactivate the duress output (see "Operating Duress Codes"
on page 24).
⢠If the keypad is powered down, any programmed visitor codes will be deleted.
When programming visitor codes, use this general formula:
â Visitor ID
â Valid Duration (hours)
â Visitor Code
Visitor IDs:
â˘
â˘
to â 50 unique visitor IDs for visitor codes for output #1.
â Delete all currently programmed visitor codes.
Valid Duration:
â˘
â Set a one-time code. This code can only be used once by a visitor, after which it is
â˘
to â Set the duration the visitor code will be valid, from 1 to 99 hours.
automatically deleted.
Visitor Codes:
⢠A visitor code can be 4 to 8 digits long, and must have the same length as all other codes if
the keypad is used in auto code entry mode (see "Programming the User Code Entry Mode"
on page 28).
⢠All visitor codes are deleted if power is lost.
Examples:
1. Set the visitor ID #01 code to 1268, and make it a one-time code:
2.
Set the visitor ID #02 code to 1378, and make it valid for three hours:
3.
Delete the visitor ID #02 from memory:
4.
Delete all currently programmed visitor codes:
22
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming Duress Codes:
Duress codes allow users to trigger a silent alarm or alert if they are forced to allow access to a
protected area. If a user uses a duress code instead of his or her normal user code, outputs #1,
#2, or #3 will activate as normal, but the duress output will simultaneously activate to trigger a
silent alarm or alert.
NOTE:
⢠Duress codes are always valid and are not inhibited by any other operation of the keypad.
⢠Duress codes cannot be the same as any other codes.
⢠Duress codes can be used either as stand-alone codes or in conjunction with a user card,
depending on how the user codes are programmed (see "Programming User Codes and
Proximity Cards" on pages 20~21).
⢠The duress code should be easy to remember. For instance, it can be the same as a
userâs normal user code, but with a single digit changed, as by subtracting or adding 1 to
the first or last digit of the code. For example, if the user code is 1369, a good duress code
might be 2369.
When programming duress codes, use this general formula:
â Output
â Duress ID
â Duress Code
Outputs:
â˘
â˘
â˘
â Output #1
â Output #2
â Output #3
Duress IDs:
â˘
â˘
â˘
to â Up to 50 duress codes can be programmed for output #1.
to â Up to 10 duress codes can be programmed for output #2 or output #3.
â Delete all currently programmed duress codes for the selected output.
Duress Codes:
⢠A duress code can be 4 to 8 digits long and must have the same length as all other codes if
the keypad is used in auto code entry mode (see "Programming the User Code Entry Mode"
on page 28).
SECO-LARM U.S.A., Inc.
23
ENFORCER Split Series Keypad with Proximity Card Reader
Programming Duress Codes (continued):
Examples:
1. Set the duress ID #01 code for output #1 to 2369:
2.
Set the duress ID #01 code for output #2 to 23980:
3.
Delete the duress ID #011 code for output #1 from memory:
4.
Delete all duress codes for output #1 from memory.
Operating Duress Codes:
If a duress code is used in place of a normal user code, both the appropriate outputs #1, #2, or #3
and the duress output will be activated. However, a duress code cannot deactivate the duress
output. Only a normal user code/card, super user code, or a master code can deactivate the
duress output.
NOTE: A duress code can also be used in conjunction with a user card to activate the duress
output. However, a user card alone cannot activate the duress output.
Examples:
In these examples, assume that is an output #1 duress code and that is a
user code.
1. Activate the duress output and output #1 using the duress code:
NOTE: Subsequently entering the duress code will activate output #1 again, but will not
deactivate the duress output.
2. Deactivate the duress output using the user code:
3.
Activate the duress output and activate output #1 using the duress code and a user card:
READ CARD
24
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Output Mode and Output Timing:
The relays for outputs #1, #2, and #3 can be programmed to trigger ON and OFF with a user code
or user card (toggle mode), or to trigger for a programmed length of time of up to nearly 28 hours
before automatically turning OFF. The toggle or timed outputs can be used for locking or
unlocking a door for a variety of functions that can be controlled with the keypad.
When programming the output mode and time, use this general formula:
â Output
â Output Mode and Time
Outputs:
â˘
â˘
â˘
â Output #1
â Output #2
â Output #3
Output Mode and Time:
â˘
â Start/stop (toggle) mode. In this case, the output starts when a user code and/or user
â˘
to â The output triggered by a user code and/or user card lasts 1 to
card is entered, and stops when a user code and/or card is entered.
99,999 seconds (nearly 28 hours) before automatically turning off (default 5 seconds).
NOTE: While the keypad is in momentary timed output mode, the output can be reset at any time
by entering the super user code.
Examples:
In these examples, assume that the super user code is
1. In programming mode, set output #1 to toggle:
.
2.
In programming mode, set output #2 to 60 seconds:
3.
Reset output #1 timer:
4.
Reset output #2 timer:
SECO-LARM U.S.A., Inc.
25
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Real-Time Clock:
A 24-hour real-time clock provides the baseline time needed to start and stop the output #1
auto-disable time (see "Programming the Output #1 Auto-Disable Time" below).
If the output #1 Auto-Disable Time is not programmed, it is not necessary to set the real-time clock.
To set the clock, use this general formula:
â Program Real-Time Clock
â Hours
â Minutes
Setting Hours and Minutes:
â˘
represents hours and
from 00:00 to 23:59.
represents minutes in the military (24-hour) time format,
Examples:
⢠Set the real-time clock to 11:30 AM:
â˘
Set the real-time clock to 7:15 PM:
NOTE:
⢠If the output #1 auto-disable time is programmed, losing power will cause the keypad to
beep 3 times every 5 seconds. To deactivate this alert, either reset the real-time clock
or clear the output #1 auto-disable time.
⢠If the output #1 auto-disable time is not programmed, losing power will not cause the
keypad to beep.
⢠To ensure accurate time, it is advised to re-program the real-time clock every three to six months
and when Daylight Savings Time begins and ends (if applicable).
Programming the Output #1 Auto-Disable Time:
The keypad can be programmed so that output #1 is disabled for a certain period of time every
day. Output #1 will be disabled at the start time, and will be re-enabled at the end time. This
ensures that users are not allowed into the protected premises, such as during lunch hour
or at night.
NOTE:
⢠The real-time clock must be operating in order to set the output #1 auto-disable time (see
"Programming the Real-Time Clock" above).
⢠For safety purposes, the egress button still works while output #1 is auto-disabled.
⢠The time is set using the military (24-hour) time format (00:00 to 23:59).
26
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Output #1 Auto-Disable Time (continued):
â˘
â˘
â˘
â˘
â˘
If the programmed start time is before the end time, output #1 is auto-disabled
within a single day. If the programmed start time is after the end time, the end time
will be on the following day.
The start time and end time cannot be the same.
The auto-disable time can be temporarily paused and restarted using the super user code
(see "Programming the Super User Code" on pages 18~19).
During the output #1 auto-disable time, the super user code can be used to
operate output #1.
The keypadâs left LED will remain red during the output #1 auto-disable time.
When programming the output #1 auto-disable time, use this general formula:
â Program Output #1 Auto-Disable Time
â Start Time
â End Time
Start Time:
â˘
Start time for output #1 auto-disable time. represents hours and
minutes in the military (24-hour) time format, 00:00 to 23:59.
represents
End Time:
â˘
End time for output #1 auto-disable time. represents hours and
minutes in the military (24-hour) time format, 00:00 to 23:59.
represents
Examples:
In these examples, assume that the super user code is .
1. In programming mode, set the output #1 auto-disable from 12:00 PM to 1:00 PM:
2.
In programming mode, set the output #1 auto-disable time from 6:30 PM to 7:30 AM the
following day:
3.
In programming mode, clear the output #1 auto-disable time:
4.
Temporarily pause and resume the output #1 auto-disable time:
5.
Activate output #1 during the auto-disable time (i.e. open the protected door):
SECO-LARM U.S.A., Inc.
27
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Wrong-Code System Lock-Up:
The keypad can be programmed to lock up in order to secure the premises against unauthorized
entry if multiple wrong codes are entered or multiple wrong user cards are tapped.
When programming the wrong-code system lock-up, use this general formula:
â Program Wrong-Code System Lock-Up
â Lock Options
Lock Options:
Choose from several different options for the wrong-code system lock-up security level:
â˘
â˘
â˘
â After 10 successive false attempts using incorrect user codes or user cards, the keypad
will lock for 60 seconds (default).
â After 10 successive false attempts using incorrect user codes or user cards, the duress
output will activate. The duress output can be deactivated using any user code or user card,
or via the super user code.
to â After 5 to 10 successive false attempts using incorrect user codes or user
cards, the keypad will lock for 15 minutes or until the super user code is used as follows:
SUPER USER CODE
â˘
â No system lock-up will happen.
NOTE: The keypadâs left LED will remain red to show that the keypad is locked. The duress code
will still function in this mode.
Programming the User Code Entry Mode:
The keypad can be programmed for auto or manual user code entry modes:
⢠Auto entry mode â Pressing the key is not required after typing in a user code. In auto
entry mode, all user codes must have the same number of digits as the master code.
⢠Manual entry mode â The key must be pressed after the user code to indicate the code
has been entered completely. In this case, the user codes can have a different number of
digits, from 4 to 8 digits.
SILVER
To Program:
⢠For auto entry mode:
â˘
For manual entry mode (default):
NOTE: If the keypad was previously programmed for manual code entry mode and then is
reprogrammed for auto entry mode, any codes whose length exceeds the number of
digits of the master code will no longer operate the keypad. However, if the keypad is
reprogrammed for manual entry mode, the longer codes will again operate the keypad.
28
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Keypad Sounds:
Some of the keypad sounds can be programmed off:
â˘
â˘
Keypad audible mode â All the keypadâs status beeps are enabled.
Keypad silent mode â The successful key entry beep (1 beep) and the unsuccessful user
code or card entry beeps (5 beeps) are disabled. However, the warning and power-up delay
beeps remain active. This provides for a quieter work environment.
To Program:
⢠To enable keypad audible mode (default):
â˘
To enable keypad silent mode:
NOTE: This programming function only impacts the keypad sounds. It does not impact the output
relay activation sounds (see "Programming the Output Relay Activation Sounds" below).
Programming the Output Relay Activation Sounds:
The keypad output sounds can be programmed for one of three modes:
â˘
No beeps â The keypad will not beep when an output is activated:
â˘
1-second beep (default) â The keypad will beep for 1 second when an output is activated:
â˘
2 short beeps â The keypad will beep twice when an output is activated:
Mercury
NOTE: This programming function only impacts the output relay activation sounds. It does not
impact the keypad sounds (see "Programming the Keypad Sounds" above).
SECO-LARM U.S.A., Inc.
29
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Amber LED Flashing during Standby Mode:
The keypadâs amber LED typically flashes while the keypad is in standby mode, but can be
programmed off if needed.
â˘
â˘
Enable amber LED flashing during standby mode (default):
Disable amber LED flashing during standby mode:
Programming the Door-Forced-Open Warning and Timing:
If the controller is connected to an optional magnetic contact or other door protection switch or
device, the keypad and controller can be programmed to beep when a door has been forced open.
The controller will also activate the alarm output and siren. The beep, siren, and alarm output can
be set to activate for 1 to 999 seconds.
â˘
â˘
Door-forced-open warning OFF (default):
Door-forced-open warning ON:
NOTE:
â˘
â˘
â˘
30
represents the beep, siren, and alarm output active time, which can be set from 1 to
999 seconds.
If programmed for door-forced-open warning, the keypad will beep and the controller will
activate the alarm output and siren for the programmed time if the door is forced open without
using a user code and/or card or the egress button. The controller will also beep until the door
is closed. There will be no output sounds or alarm output activation if the door is opened with
a user code and/or card or the egress button.
The door-forced-open warning and the door open alarm should not both be enabled, as the
overlap in timing could result in incorrect alarm outputs (see "Programming the Door Open
Alarm and Timing on page 31).
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Door-Propped-Open Warning and Delay Time:
If the controller is connected to an optional magnetic contact or other door production switch or
device, The keypad can be programmed to beep when a door is propped open. This prompts
authorized users to close a door that was not closed properly or to investigate a door that may
have been deliberately propped open.
â˘
Door-propped-open warning OFF (default):
â˘
Door-forced-open warning ON:
NOTE:
â˘
â˘
â˘
represents the delay time on the controller, which can be set from 1 to 999 seconds.
The delay time provides time for a door to close normally before triggering the door-proppedopen warning.
The door-propped-open beeping will stop when the open door is closed.
Programming the Door Open Alarm and Timing:
If the controller is connected to a magnetic contact or other door monitoring device, the controller
can be programmed to trigger the alarm output and siren for 1 to 999 seconds if the door is
opened. In this case, if the alarm output is triggered, the output either automatically ends at the
end of the programmed time or when a user code or super user code is input for output #1.
NOTE:
â˘
â˘
If programmed for the door open alarm, the alarm output and siren will activate for the
programmed time when the door is forced open or opened with the egress input. There is no
alarm output activation if the door is opened with a valid user code and/or card.
The door open alarm and door-forced-open warning should not both be enabled, as the
overlap in timing could result in incorrect alarm output (see "Programming the Door-ForcedOpen Warning and Timing on page 30).
To Program:
â˘
Door open alarm OFF (default):
â˘
Door open alarm ON:
NOTE:
represents the alarm output time, which can be set from 1 to 999 seconds.
SECO-LARM U.S.A., Inc.
31
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Egress Delay/Warning/Alarm:
With most keypads, the egress button provides a simple way for someone inside a protected
premises to exit through a locked door by pressing a button instead of using a keypad. However,
in some situations, delaying the egress operation and/or providing some warning or alarm when
the egress button is used is desirable.
For example, in hospitals or schools, it may be desirable to delay the egress operation and
provide a warning to prevent patients or young children from easily leaving the protected area.
For simple egress with no delay, warning, or alarm, do not change this setting. It is disabled by
default.
When programming the egress delay/warning/alarm, use this general formula:
â Program Egress Delay/Warning/Alarm
â Egress Mode
â Delay Time
Egress Modes:
There are six possible egress operation configurations for the SK-4131-SPSQ:
â˘
Momentary contact with no warning or alarm (default) â Press the egress button
â˘
Momentary contact with warning beep â Press the egress button momentarily. The
â˘
Momentary contact with warning beep, alarm, and siren â Press the egress button
â˘
Hold contact with no warning or alarm â Press and hold the egress button for the
â˘
Hold contact with warning beep â Press and hold the egress button for the programmed
delay time until the door is open. The keypad and controller will beep during the delay time
before letting the door open, to warn that someone is preparing to exit the protected area.
â˘
Hold contact with warning beep, alarm, and siren â Press and hold the egress button for
32
momentarily. The door opens instantly (default) or after the programmed delay time with no
audible warning.
keypad and controller will beep for the programmed delay time before letting the door open,
to warn that someone is preparing to exit the protected area.
momentarily. The keypad and controller will beep and the alarm output and siren will activate
for the programmed delay time before letting the door open, to warn that someone is
preparing to exit the protected area.
programmed delay time until the door is open. This prevents accidental opening of the door.
the programmed delay time until the door is open. The keypad and controller will beep and
the alarm output and siren will activate for the programmed delay time before letting the door
open, to warn that someone is preparing to exit the protected area.
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Programming the Egress Delay/Warning/Alarm (continued):
NOTE: When the egress button is programmed to hold for a delay time before the door is
released, it is important to put a sign near the egress button to notify users of the
delay time.
Delay Time:
â˘
â No delay time (default): Output #1 operates immediately when the egress button is
â˘
to â Egress button delay time: The delay time can be set from 1 to 99 seconds. This
pressed.
tells the keypad how long to wait after the egress button is pressed before activate output #1.
Examples:
1.
Momentary mode â Press the egress button, and the keypad and controller will beep for 5
seconds before output #1 activates:
2.
Hold the button to activate â Press and hold the egress button for 10 seconds, and the keypad
and controller will beep for those 10 seconds before output #1 activates:
3.
Return to default setting â Press the egress button to activate output #1 with no beeping or
delay:
NOTE: For safety and to avoid confusion, when a delay or a press-and-hold delay is programmed,
please post a notice near the egress button, such as "Press and hold the button for 5
seconds or until the door is unlocked."
SECO-LARM U.S.A., Inc.
33
ENFORCER Split Series Keypad with Proximity Card Reader
Direct Access to Programming (DAP):
Direct Access to Programming (DAP) is used to enter programming mode if the master code is
forgotten. DAP will not change the programming of the SK-4131-SPSQ in any way.
To Use DAP:
1. Disconnect the keypadâs power.
2. Wait one minute to ensure that the keypadâs power is fully discharged.
3. Reconnect the power. The keypad will beep repeatedly for one minute.
4. While the keypad is beeping, move the DAP jumper to the ON position then back to the OFF
position once to stop the beeping.
5. Enter the DAP code:
6.
The amber LED will turn ON, indicating that the keypad is ready for a new master code to be
programmed.
NOTE:
⢠See "Programming the Master Code" on page 17 for how to program a new master code.
⢠Direct Access to Programming (DAP) will not reset the keypadâs programming. It will only
enter programming mode in order to program a new master code.
⢠For complete system reset, see "System Restore" on page 17.
34
SECO-LARM U.S.A., Inc.
ENFORCER Split Series Keypad with Proximity Card Reader
Userâs Guide to Operating the SK-4131-SPSQ:
See "Programming the Master Code" and "Programming the Super User Code" on pages 17~19 for
functions specific to those authorized to use those codes.
Opening the Door:
In these examples, assume that the user code is , the common user code is
, and a unique user code is .
â˘
Security Level 1 â Card only
READ CARD
1 Long beep indicates that the door can be opened.
â˘
Security Level 2 â Code only
*
1 Long beep indicates that the door can be opened.
â˘
Security Level 3 â Card + Common user code
READ CARD
2 Short beeps and a rapidly flashing amber LED indicates the card is accepted and the keypad
is waiting for the Common user code.
*
1 Long beep indicates that the door can be opened.
â˘
Security Level 4 â Card + Unique user code
READ CARD
2 Short beeps and a rapidly flashing amber LED indicates the card is accepted and the keypad
is waiting for the Unique user code.
*
1 Long beep indicates that the door can be opened.
NOTE: For more information on security levels, please see "Getting Ready to Program" on
page 14.
Operating the Egress Button:
Press the egress button from inside the protected premises to unlock the door and exit without
using the keypad.
NOTE: For more information or programming the Egress button, please see "Programming the
Egress Delay/Warning/Alarm" on pages 32~33).
* The key is not needed if the keypad is programmed for auto entry mode. See page 28.
SECO-LARM U.S.A., Inc.
35
ENFORCER Split Series Keypad with Proximity Card Reader
Notes:
Also Available:
Proximity Cards
(sold in packs of 10)
PR-K1S1-A
FCC COMPLIANCE STATEMENT
Proximity Fobs
(sold in packs of 10)
PR-K1K1-AQ
FCC ID: K4E4131SPKQ
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
( 2 ) : The change or modifications not expressly approved by the party responsible for compliance could void the userâs
authority to operate the equipment.
IMPORTANT N OTE: T o c omply w ith t he F CC RF exposure c ompliance r equirements n o c hange t o t he a ntenna or t he
device i s per mitted. A ny c hange t o t he ant enna or t he dev ice c ould r esult i n t he d evice ex ceeding t he R F ex posure
requirements and voice userâs authority.
LIMITED LIFETIME WARRANTY: This SE CO-LARM product i s w arranted against d efects in m aterial an d
workmanship while used in normal service for the lifetime of the product. SECO-LARMâs obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty i s vo id i f
damage i s c aused by or at tributed t o a cts of G od, physical or el ectrical m isuse or a buse, neglect, r epair or al teration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not o perating pr operly as a r esult of c auses ot her t han d efects i n m aterial a nd w orkmanship. The s ole obl igation of
SECO-LARM and the purchaserâs exclusive remedy, shall be l imited to the replacement or repair only, at SECO-LARMâs
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else. This limited lifetime warranty is for products sold and installed in the
United States and Canada. For all other countries, the warranty is 1 (one) year.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright Š 2017 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARMÂŽ U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606
Phone: (949) 261-2999 | (800) 662-0800
36
Website: www.seco-larm.com
Email: sales@seco-larm.com
PIHAK1
MI_SK-4131-SPSQ_161220.docx
SECO-LARM U.S.A., Inc.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may casue harmful interference to radio communications,
However, there is no guarantee that interference will not occur in a particular
installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.
37
SECO-LARM U.S.A., Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Has XFA : No Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Modify Date : 2017:01:05 11:26:57+08:00 Create Date : 2016:12:20 13:47:13-08:00 Metadata Date : 2017:01:05 11:26:57+08:00 Creator Tool : Acrobat PDFMaker 15 for Word Document ID : uuid:17294775-a0d6-4d2f-8f40-9daa96fe6880 Instance ID : uuid:852d2089-9c9f-4d9c-a75a-17006b4a1f7c Subject : 3 Format : application/pdf Creator : Robert Mattern Producer : Adobe PDF Library 15.0 Source Modified : D:20161220214706 Company : Microsoft Page Layout : OneColumn Page Count : 37 Author : Robert MatternEXIF Metadata provided by EXIF.tools