Superior Electronics 931CS22RF Wireless Door Entry Alarm & Counting System (Infrared Beam)/Solar Panel Included User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2086182
Application ID	oRVdVkh3rML9XKbHApFWzA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	84.71kB (1058851 bits)
Date Submitted	2013-09-29 00:00:00
Date Available	2013-09-29 00:00:00
Creation Date	2013-09-16 16:31:49
Producing Software	doPDF Ver 7.1 Build 330 (Windows 7 (Service Pack 1) - Version: 6.1.7601 (Platform: x64))
Document Lastmod	2013-09-16 16:38:41
Document Title	英文使用手冊_頁面_1
Document Creator	英文使用手冊_頁面_1
Document Author:	amy chen

ENFORCER Wireless Entry Alert System
ENFORCER Wireless Entry Alert System
Introduction:
Installation:
The ENFORCER Wireless Entry Alert System is a self-contained easy-to-install alert system for commercial or home
applications. Each set contains a reflective photoelectric beam sensor that, when tripped, communicates wirelessly with a
speaker installed up to 328ft (100m) away*. An additional speaker may be installed to alert more than one area on the
property and an optional solar charger may be installed with the sensor for even more convenience.
1. Install the reflector and sensor so they face each other about 2ft (61cm) off the ground.
2. Install the speaker within 328ft (100m) of the sensor.
3. Connect an included power adapter to the sensor. If optional solar charger is used, see pg. 4, Installing the Optional
Solar Charger.
4. Connect an included power adapter to the speaker.
5. To find the correct alignment, slowly adjust the angles of the sensor and reflector.
NOTE: Alignment is correct when the red LED turns ON.
Specifications:
Sensor
Up to 22ft (7m)
Sensing range
Wireless range
Operating frequency
Operating voltage
Standby
Current draw
Active
Power input
Light source
Operating temperature
Volume
Alarm time range
Speaker output
IP Rating
Speaker
N/A
Mounting:
Up to 328ft (100m)*
433.92 MHz
12VDC
5mA
20mA
Sensor
2.5mm DC Jack
N/A
32°~122° F (0°~50° C)
N/A
N/A
N/A
IP55
31/4”x29/16”x11/2”
(82x66x38 mm)
0~90 dB
3~30 s (Adjustable)
Chime/Off/Alarm (selectable)
N/A
31/4”x215/16”x19/16”
(83x75x40 mm)
*Range may vary greatly depending on the installation and operating environment.
Parts List:
1x Sensor
1x Speaker
1x Reflector
2x Power adapters
1x Small screwdriver
1x Mode adjustment pin
1x Sensor mounting bracket
1x Reflector mounting bracket
2x Bolts (Sensor)
2x Bolts (Reflector)
4x Nuts
5x Mounting screws
1x Screw anchor
1x Manual
Sensor
Reflector
29/16”
(66mm)
Alignment
LED
Speaker
19/16”
21/16”
(52mm)
23/8”
(61mm)
2.5mm
DC Jack
3/ ”
(40mm)
Alert tone
selection
Cable length:
215/16”
(75mm)
(9mm)
31/4”
(83mm)
Counter output
97/8”
Timer Volume
Mode button
1. Attach the sensor or reflector to their respective brackets by using the
included bolts and nuts.
2. Mount the bracket to the wall using two of the included mounting screws.
Programming the Speaker:
1. Choose between Chime, Alarm, and Off using the alert tone selection switch on the side of the speaker.
2. Adjust the volume by using the included Phillips screwdriver to turn the volume adjustment screw. Turning clockwise
increases the volume; counter-clockwise decreases the volume.
3. Adjust the timer by using the included Phillips screwdriver to turn the timer adjustment screw. Turning all the way
clockwise will set the timer for 30 seconds; turning all the way counter-clockwise will set the timer for three seconds.
NOTE: Timer mode only applies if Alarm is chosen as the alert tone.
2.5mm
DC Plug
Use one of the two methods below to pair the optional additional speaker with the sensor.
NOTE: The speaker included with the Wireless Entry Alert System is pre-paired with the sensor.
Method 1:
Clearing Memory:
Method 2:
1. Use the included mode adjustment
1. Use the included mode adjustment
1. Remove the side panel of the
pin to press and hold the mode
pin to press and hold the mode
sensor with the included small
switch until you hear a long beep
switch until you hear a long beep
Phillips screwdriver.
from speaker. This means the
and two short beeps after five
2. Perform the point 1 of “Method 1”
speaker is in the learning mode.
seconds.
and then press sensor’s learning
2. Trigger the sensor by breaking the
button once. The speaker will beep 2. Release the mode button and the
beam. The speaker will beep once.
memory has been cleared.
once.
3. After 10 seconds, the speaker will
3. After 10 seconds, the speaker will
make one long beep indicating
make one long beep indicating
successful pairing.
successful pairing.
(250mm)
Learning button
Optional Accessories:
Additional Wireless
Speaker
E-931ACC-SFQ
Solar Charger
for Sensor
E-931ACC-SPQ
1. Drill included screw into wall.
2. Hang speaker on screw.
Pairing the Sensor and Optional Additional Speakers (E-931ACC-SFQ):
Overview:
31/4”
(82mm)
Speaker
25mA
100mA
IR LED
Dimensions
11/2”
(38mm)
Reflector
Digital Counter
E-931ACC-CQ
Hood for Square and
Round Reflectors
E-931ACC-HR1Q
IMPORTANT: When pairing additional speaker, release the mode switch immediately after two seconds and hearing the
long beep. Pressing the mode switch for more than five seconds will delete the memory.
Replacement
Square Reflector
E-931ACC-R2Q
Connecting the Optional Counter (E-931ACC-CQ):
3” Round
Reflector
E-931ACC-RC1Q
1. Connect the plug from the counter to the counter output jack of the speaker.
2. Test the counter. Each time the beam is broken, the counter should
automatically increase by 1.
3. Manually add or subtract 1 by pressing the “+” or “-“ buttons
4. Reset the counter by pressing “RESET”.
SECO-LARM U.S.A., Inc.
SECO-LARM U.S.A., Inc.
The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to
Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference to
radio communication.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of more of the following measures: -
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or
modifications not expressly approved by the party responsible for compliance could void your authority to
operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.
OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
This device may not cause harmful interference and
This device must accept any interference received, including interference that may cause undesired
operation.
The antenna used for this transmitter must not be collocated or operation in conjunction
with any other antenna or transmitter.
Notice :
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user’s authority to operate
the device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2013:09:16 16:31:49+08:00
Creator Tool                    : 英文使用手冊_頁面_1
Modify Date                     : 2013:09:16 16:38:41+08:00
Metadata Date                   : 2013:09:16 16:38:41+08:00
Format                          : application/pdf
Creator                         : amy chen
Title                           : 英文使用手冊_頁面_1
Producer                        : doPDF Ver 7.1 Build 330 (Windows 7 (Service Pack 1) - Version: 6.1.7601 (Platform: x64))
Document ID                     : uuid:220da3ca-ec04-4358-a660-ab5183c0dd43
Instance ID                     : uuid:8c723edf-adee-4503-8dc5-ec46eefa0ce6
Has XFA                         : No
Page Count                      : 3
Page Layout                     : OneColumn
Author                          : amy chen

EXIF Metadata provided by EXIF.tools