Sweepscrub American Lincoln Sr5730 Rider Floor Scrubber Foot Pedal Service Kit Installation Instructions 56090079 User Manual

User Manual: Sweepscrub American-Lincoln-Sr5730-Rider-Floor-Scrubber-Foot-Pedal-Service-Kit-Installation-Instructions american-lincoln-sr5730-rider-floor-scrubber-foot-pedal-service-kit-installation-instructions 2255 file product_file sweepscrub

Open the PDF directly: View PDF .
Page Count: 5

© 2014 Nilfi sk-Advance, Inc. 9/10 revised 9/14 Form No. 56090079 REV B

(page 1 of 5)

56381488 FOOT PEDAL SERVICE KIT

5730 / ENCORE R

7730 / CR1000

CONTENTS OF KIT

ITEM PART NO. QTY DESCRIPTION

56090079 1 Instruction Sheet

1 56381486 1 Adapter Foot Pedal

2 56381484 1 Foot Pedal FWD/REV

5730 / ENCORE R INSTALLATION INSTRUCTIONS

WARNING!

DISCONNECT BATTERIES BEFORE SERVICING.

1 See Figure 1. Loosen the two mounting Screws (A) at the front of the fl oor panel.

FIGURE 1

© 2014 Nilfi sk-Advance, Inc. 9/10 revised 9/14 Form No. 56090079 REV B

(page 2 of 5)

REMOVE OLD FOOT PEDAL

2 See Figure 2. Remove the three Nuts (B) at the rear of the fl oor panel. Tilt the rear of the Floor Panel (C) up far enough to reach underneath

and disconnect the wiring from the Foot Pedal Assy (D).

3 Remove the three Screws and Nuts (E) that hold the Foot Pedal (D) in place and remove it from the machine.

FIGURE 2

© 2014 Nilfi sk-Advance, Inc. 9/10 revised 9/14 Form No. 56090079 REV B

(page 3 of 5)

INSTALL NEW FOOT PEDAL

4 See Figure 3. Cut the old foot pedal Wiring Connector (F) off of the machine harness. Cut and strip the three wires from the old connector as

shown and then crimp each of them into the new Adapter (1) as shown.

5 Plug the new Adapter (1) into the new Foot Pedal (2) and mount the new Pedal in place of the original reusing the original three Screws and Nuts

(E).

FIGURE 3

BROWN

BLACK

RED

310

320 309

2.00" (5.08cm)

2.00" (5.08cm)

F

1

© 2014 Nilfi sk-Advance, Inc. 9/10 revised 9/14 Form No. 56090079 REV B

(page 4 of 5)

7730 / CR1000 INSTALLATION INSTRUCTIONS

WARNING!

DISCONNECT BATTERIES BEFORE SERVICING.

REMOVE OLD FOOT PEDAL

1 See Figure 1. Remove the three Screws (A) and lift up Panel (B) far enough to disconnect the wiring from the old Foot Pedal (C).

2 Remove the three Screws and Nuts (D) that hold the Foot Pedal (C) in place and remove it from the machine.

FIGURE 1

© 2014 Nilfi sk-Advance, Inc. 9/10 revised 9/14 Form No. 56090079 REV B

(page 5 of 5)

INSTALL NEW FOOT PEDAL

3 See Figure 2. Cut the old foot pedal Wiring Connector (E) off of the machine harness. Cut and strip the three wires from the old connector as

shown and then crimp each of them into the new Adapter (1) as shown.

4 Plug the new Adapter (1) into the new Foot Pedal (2) and mount the new Pedal in place of the original reusing the original three Screws and Nuts

(D).

FIGURE 2

BROWN

BLACK

RED

NEG-18-3

NEG-18-3

97-18-3

2.00" (5.08cm)

2.00" (5.08cm)

E

1