Sweepscrub American Lincoln Sr5730 Rider Floor Scrubber Foot Pedal Service Kit Installation Instructions 56090079 User Manual
2017-10-04
User Manual: Sweepscrub American-Lincoln-Sr5730-Rider-Floor-Scrubber-Foot-Pedal-Service-Kit-Installation-Instructions american-lincoln-sr5730-rider-floor-scrubber-foot-pedal-service-kit-installation-instructions 2255 file product_file sweepscrub
Open the PDF directly: View PDF .
Page Count: 5
Download | |
Open PDF In Browser | View PDF |
56381488 FOOT PEDAL SERVICE KIT 5730 / ENCORE R 7730 / CR1000 CONTENTS OF KIT ITEM 1 2 PART NO. 56090079 56381486 56381484 QTY 1 1 1 DESCRIPTION Instruction Sheet Adapter Foot Pedal Foot Pedal FWD/REV 5730 / ENCORE R INSTALLATION INSTRUCTIONS WARNING! DISCONNECT BATTERIES BEFORE SERVICING. 1 See Figure 1. Loosen the two mounting Screws (A) at the front of the floor panel. FIGURE 1 © 2014 Nilfisk-Advance, Inc. (page 1 of 5) 9/10 revised 9/14 Form No. 56090079 REV B REMOVE OLD FOOT PEDAL 2 See Figure 2. Remove the three Nuts (B) at the rear of the floor panel. Tilt the rear of the Floor Panel (C) up far enough to reach underneath and disconnect the wiring from the Foot Pedal Assy (D). 3 Remove the three Screws and Nuts (E) that hold the Foot Pedal (D) in place and remove it from the machine. FIGURE 2 © 2014 Nilfisk-Advance, Inc. (page 2 of 5) 9/10 revised 9/14 Form No. 56090079 REV B INSTALL NEW FOOT PEDAL 4 See Figure 3. Cut the old foot pedal Wiring Connector (F) off of the machine harness. Cut and strip the three wires from the old connector as shown and then crimp each of them into the new Adapter (1) as shown. 5 Plug the new Adapter (1) into the new Foot Pedal (2) and mount the new Pedal in place of the original reusing the original three Screws and Nuts (E). FIGURE 3 F 2.00" (5.08cm) 2.00" (5.08cm) 320 RED © 2014 Nilfisk-Advance, Inc. 310 309 BLACK 1 BROWN (page 3 of 5) 9/10 revised 9/14 Form No. 56090079 REV B 7730 / CR1000 INSTALLATION INSTRUCTIONS WARNING! DISCONNECT BATTERIES BEFORE SERVICING. REMOVE OLD FOOT PEDAL 1 See Figure 1. Remove the three Screws (A) and lift up Panel (B) far enough to disconnect the wiring from the old Foot Pedal (C). 2 Remove the three Screws and Nuts (D) that hold the Foot Pedal (C) in place and remove it from the machine. FIGURE 1 © 2014 Nilfisk-Advance, Inc. (page 4 of 5) 9/10 revised 9/14 Form No. 56090079 REV B INSTALL NEW FOOT PEDAL 3 See Figure 2. Cut the old foot pedal Wiring Connector (E) off of the machine harness. Cut and strip the three wires from the old connector as shown and then crimp each of them into the new Adapter (1) as shown. 4 Plug the new Adapter (1) into the new Foot Pedal (2) and mount the new Pedal in place of the original reusing the original three Screws and Nuts (D). FIGURE 2 E 2.00" (5.08cm) 2.00" (5.08cm) 97-18-3 RED © 2014 Nilfisk-Advance, Inc. NEG-18-3 NEG-18-3 BLACK 1 BROWN (page 5 of 5) 9/10 revised 9/14 Form No. 56090079 REV B