E FANG32T Operator Manual
2016-03-15
: Sweepscrub Fang32T Operator Manual FANG32T_operator_manual 1233 file product_file
Open the PDF directly: View PDF 
.
Page Count: 29
| Download | |
| Open PDF In Browser | View PDF |
REV.02(09-12) CONGRATULATIONS on your purchase of a Viper product, and welcome to the V.I.P. family. We appreciate your business and will do everything in our power to keep you happy with your purchase for many years to come. As part of the V.I.P. family, you are entitled to the best protection by one of the most comprehensive warranties in the industry. Thank-you for purchasing Viper products! Tom VanderBie, CEO TABLE OF CONTENTS SAFETY PRECAUTIONS MACHINE COMPONENTS MACHINE SET UP MACHINE INSTALLATION MACHINE OPERATION TANK DRAINING BATTERY CHARGING PREVENTATIVE MAINTENANCE MACHINE STORAGE BASIC TROUBLESHOOTING PARTS BREAKDOWNS AND LISTS WIRING DIAGRAM 3 4 5 5-6 6 7 7-8 8-9 10 11 12-32 33 2 x x SAFETY PRECAUTIONS x This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories. x x x Secure machine with wheel blocks prior to jacking the machine up. Use approved jack or hoist to safely elevate the machine. Disconnect batteries prior to working on machine. Wear gloves when handling batteries or battery cables. Avoid any contact with battery acid. Avoid moving parts. Do not wear loose fitting clothing while servicing machine. All operators shall read, understand and exercise the following safety precautions: : Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging. 1) DO NOT OPERATE MACHINE: x Unless trained and authorized. x Unless you have read and understand the operators manual. x In flammable or explosive areas. x If not in proper operating condition. x In outdoor areas. : Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. 2) BEFORE OPERATING MACHINE: x Make sure all safety devices are in place and operate properly. : Flammable materials or reactive metals can cause explosion or fire. Do not pick up. 3) WHEN USING MACHINE: x Go slow on inclines and slippery surfaces. x Follow all safety guidelines. x Be very careful when using the machine in reverse. x Report and fix any damage to machine prior to operating it. 4) BEFORE LEAVING OR SERVICING MACHINE: x Stop machine on level ground. x Turn machine off. 5) WHEN SERVICING MACHINE: x Read operators manual thoroughly prior to operating or servicing this machine. x Use manufacturer supplied or approved replacement parts. 3 4 MACHINE SET UP & INSTALLATION MACHINE SET UP UNCRATING MACHINE PRE-OPERATION CHECKS Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: Machine, batteries (x6), squeegee assembly, battery charger and pad drivers. (Batteries and charger may be on separate skid) 1. Sweep or dust mop the surface to be cleaned. 2. Check battery meter to make sure batteries are fully charged. (SEE BATTERY CHARGING) 3. Ensure squeegee is properly installed. 4. Ensure that brush/pad is properly installed. INSTALLING PAD DRIVERS OR BRUSHES 1. Ensure the machine is turned off. 2. Raise the brush head assembly off the floor by BATTERY CONNECTIONS pushing on the brush lift button on the control The batteries and charger are shipped separately console. and will need to be installed and connected as 3. Slide back the viewing window panel on the shown in the diagram below. aluminum deck housing. 4. If using a pad driver, first attach the : Batteries emit hydrogen gas. appropriate pad to the bottom of the driver. Explosion or fire can result from hydrogen gas. 5. Slide the pad driver under the deck and look through the viewing panel and line the three Keep sparks and open flames away! Keep lugs with the three holes in the drive motor battery compartment open while charging. 1.Be sure the power switch is in the "off" position. hub. Once in the holes, rotate the driver 2. Open recovery tank to gain access to battery toward the spring clip to lock the driver in compartment. place 3. Carefully place the six batteries into the compartment as shown in figure below. Place MOUNTING THE SQUEEGEE the battery brace at the rear of the batteries. 4. Connect battery cables to posts in order as 1. Pull the squeegee lift lever to raise the shown in diagram below. (RED to POSITIVE squeegee bracket up. and BLACK to NEGATIVE) 2. Loosen the two knobs on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the back) 3. Tighten the knobs securely. 4. Secure the vacuum hose on the pick-up tube of the squeegee. 5. Apply a coating or protective spray on the cable connections to prevent battery corrosion. DO NOT DROP THE BATTERIES INTO COMPARTMENT! 5 5. Turn vacuum motor switch to "on" position. (see machine components, item #1) 6. Turn the brush motor switch to "on" position. (see machine components, item #2) a. Brushes will not spin until the operating triggers are pulled. 7. Turn the solution switch to "on" position. (see machine components, item #3) a. Solution will not begin to flow until the operating triggers are pulled. 8. To begin scrubbing, pull on one or both of the red operating triggers. (see machine components, item #27) When the triggers are pulled, the brushes will begin to spin, the solution will begin to flow, and the machine will propel itself. 9. This machine is self-propelled. The speed can be adjusted by a dial located on the right side of the control housing. (see machine components, item #9) 10. This machine has reverse. In order to activate reverse, there is a toggle switch on the left side of the control housing. (see machine components, item #20) The toggle switch must be pulled / pressed to activate reverse motion. FILLING THE SOLUTION TANK 1. The FANG32T can only be filled in the rear of the machine. There is a fill cap that can be removed so the tank can be filled with a hose. 2. Fill the solution tank with up to 30 gallons of water. (water temperature should not exceed 140 degrees F) 3. The clear tube under the fill port has gallon markers to help determine the water level in the solution tank. : Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your Viper distributor for recommended chemicals. MACHINE OPERATION : Do not operate machine unless you have read and understand this manual. 1. Before the machine will operate, the key switch must be turned into the "on" position. The key is located on the left side of the control housing. (see machine components, item #19) 2. Set control housing to a comfortable operating height by squeezing together the tow thumb levers directly underneath the housing (see machine components item #16) 3. Lower squeegee assembly to the floor. There is a squeegee lift handle located on the back left of the machine, just under the control housing. (see machine components, item #14) Slightly lift up on the handle and move it to the right, the squeegee is now ready to be lowered to the floor. 4. Lower the brush head to the floor by pushing the brush lower button on the control housing. (see machine components, item #7) : Do not keep the machine in the same position with the pad / brush spinning, or you could cause damage to the floor. 11. Adjust the amount of solution flow by turning the solution control knob. Turn the knob to the right for more solution, or turn left for less solution. (see machine components, item #8) 12. There is an hour meter located on the top of the control housing. (see machine components, item #4) The operator can see the operation time. 6 breakers are located on the rear panel of the control housing. WHILE OPERATING MACHINE 1. Occasionally look through the clear recovery tank lid to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank. TANK DRAINING 1. Turn the power off on the machine : Foam must not enter the float shut- 2. With the squeegee and brush head in their "up" position, transport the machine to an off screen, or damage can occur to the vacuum approved area for draining the tank(s). motor. Foam will not activate the machines float shut-off device. DRAINING THE RECOVERY (DIRTY) TANK 2. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine. : Anytime scrubbing is completed, or 3. Occasionally check the battery level meter. when refilling the solution tank, the recovery (see machine components, item #3) When the tank should also be drained and cleaned. meter is in the red, recharge the batteries. : When battery meter is in the red, do : If the recovery tank is not drained not continue to operate the machine. Battery when the solution tank has been refilled, foam damage may occur. or water may enter the float shut-off mechanism and cause damage to the vacuum 4. If the squeegee assembly leaves streaks on the motor. floor, raise the squeegee off the floor and wipe 1. Remove the drain hose from the holder and the blades down with a damp cloth. place the drain hose over a floor drain. Twist : Do not use your fingers to wipe or off the drain hose plug to begin the draining process. In order to completely empty the remove debris from the blades, as injury may recovery tank, hinge open the recovery tank occur. and let it rest on the support stand. 2. Clean the recovery tank after every use. Use a 5. When the solution tank runs empty, turn off fresh water hose to rinse out the inside of the the brush switch, solution switch, and raise the brush head. Keep the squeegee down and tank. Be careful not to spray water into the float shut- off mechanism. continue to vacuum until all the dirty water is picked up. (see TANK DRAINING section to learn how to drain recovery and solution tanks) : If you are storing the machine for any period of time, always leave the clear recovery : The brush motors are circuit breaker tank lid off the tank so the tank may dry protected to protect them from damage. If a completely, and smell fresh. breaker trips, it can't be reset immediately. You must first determine what caused the 3. Replace the drain hose plug tightly as soon as you are done draining the tank. breaker to trip, and allow the motor to cool down before you can reset the breaker. The 7 DRAINING THE SOLUTION (CLEAN) TANK machine, make sure the battery compartment is left open. : Anytime scrubbing operation is 1. Place charger and machine in a well ventilated area. completed, the solution tank should be drained 2. Turn machine off. and cleaned. 3. Open recovery tank up, exposing battery compartment. 1. Pull down on the clear tube (back left of the 4. Check fluid level in each battery cell. Do not machine) to remove it from the hose barb. charge batteries unless fluid is slightly This will allow the solution to flow freely into covering the battery plates. Do not overfill the a bucket or floor drain. batteries. Overfilling may cause the batteries 2. Rinse the solution tank with clean water after to overflow during charging due to expansion. every use. This will help prevent chemical Replace the caps prior to charging. buildup and clogging of the solution lines. 5. Plug approved charger into grounded wall 3. With clean water in the solution tank, turn outlet before plugging the charger into the machine power on, solution switch "on" and machine. pull the operating triggers. This will allow the 6. Plug charger into grey charger receptacle clean water to flush through and clean the located in the front left of the battery solution plumbing. compartment. 4. Once the tank is rinsed, flushed and drained, 7. Flip up the recovery tank "kick stand" and reconnect the clear tube to the hose barb. Be gently lay the recovery tank down until it rests sure the tube is pushed all the way up on the on the stand. hose barb. 8. The charger will automatically begin to charge the batteries, and it will automatically BATTERY CHARGING shut down once the batteries are fully charged. 9. Upon completion of charging, first unplug the charger from the wall outlet and then : Use only approved chargers with the disconnect the charger from the machine. 10. Check the battery fluid level after charging is following specifications: completed. If the fluid level is low, add distilled water to bring the fluid level up to the x Automatic shut-off circuit bottom of the sight tubes. Replace the caps x Deep cycle charging and wipe the batteries down with a towel. x Output current of 20-30 Amps. x Output voltage of 36 volts. : For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition discharged condition. : Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. When charging the 8 2. Check batteries for loose or corroded cables. 3. Keep battery tops clean from corrosion. PREVENTITIVE MAINTENANCE MONTHLY MAINTENANCE : Before performing any maintenance 1. Check machine for leaks and lose fasteners. on the machine, be sure that the power is 2. Lubricate all grease points and pivot points with silicon spray and approved grease. turned off, or the batteries disconnected. 3. Place machine over a floor drain. Flush solution system by pouring 3 gallons of hot : Repairs are to be completed by an water and approved alkaline detergent into the solution tank and running machine (with authorized Viper service center only. Any solution control on) for 45 seconds. Turn repairs completed by unauthorized persons will machine off and let it sit over-night. The void the warranty. following day, drain the remaining solution and rinse the solution tank out with clean water. DAILY MAINTENANCE 1. Remove pad driver / brush and clean with approved cleaner. 2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary. 3. Raise squeegee assembly off the floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position. 4. Remove the float shut-off assembly and rinse it out with clean water. VACUUM MOTOR MAINTENANCE 1. Contact your local Viper Distributor for any motor maintenance. 2. Vacuum motor should have the brushes checked every 250 hours. Brushes should be replaced when they are worn to a length of 10mm or less. BATTERY MAINTENANCE : For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. : Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all time. 5. Clean machine with an approved cleaner and a : Whenever servicing batteries, be damp towel. 6. Recharge batteries. sure to wear protective gloves. Avoid contact with battery acid at all times! 1. Always follow the battery charging directions WEEKLY MAINTENANCE as outlined in the BATTERY CHARGING section of this manual. 1. Check fluid level in batteries. 9 Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS. 3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections. 4. Check battery connections for wear and loose terminals. Replace if necessary. 2. MACHINE STORAGE 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always store the machine with pads brushes removed. 4. Always store the machine with the squeegee assembly in up position. 5. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty. Remove VF82168-2 solution filter cover to drain all fluid form hoses. 6. Drain the recovery tank and remove the clear lid on the top of the recovery tank so that it can "breathe" during storage. 7. Drain the solution tank of all fluid. 10 BASIC TROUBLESHOOTING PROBLEM No power CAUSE Bad batteries Key not in "ON" position Main circuit breaker tripped Batteries need to be charged Loose battery cable Batteries not connected properly Bad brush switch Brush circuit breaker has tripped Bad wiring Bad brush motor Carbon brushes worn out Bad solenoid Bad vacuum switch Bad wiring Bad vacuum motor Carbon brushes worn out Batteries need to be charged Batteries need maintenance Bad cell in battery(s) Bad charger Bad solution switch Clogged solution solenoid Clogged solution filter Solution line obstructed SOLUTION Replace batteries Turn key "ON" Contact Viper Distributor Charge batteries (see Battery Charging) Tighten loose cable(s) Follow battery installation instructions Contact Viper Distributor Brush motor does Check brush motor for obstructions and reset breaker not run Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Vacuum motor Contact Viper Distributor does not run Contact Viper Distributor Charge batteries (see Battery Charging) Short run time See Battery Maintenance in this manual Replace batteries Replace charger Contact Viper Distributor Contact Viper Distributor Little or no solution Remove filter and clean flow Remove solution line and clean Increase flow by twisting solution adjustment knob to the Solution flow adjustment knob in need right. Decrease flow by twisting solution adjustment knob of adjustment to the left. Squeegee clogged Clean debris off squeegee with damp towel Poor water pick up Squeegee blades worn Install new squeegee blades Confirm that the squeegee assembly is securely fastened Squeegee not mounted correctly to the machine and not loose fitting. Check hose connections and make sure they are firm. Vacuum hoses have a hole or are loose Replace hose if damaged. Vacuum hose may be clogged Check hose for debris and remove any clog. Drain hose stopper is loose Tighten drain plug. Batteries need to be charged Charge batteries (see Battery Charging) Tighten vac motor mounting screws. Do not overtighten Vacuum motor is loose or damage will occur. Recovery tank lid is loose Confirm the clear recovery tank lid is securely in place. Drain recovery tank and tilt tank on side. Check the inlet Recovery tank inlet hole is clogged hole for debris and remove debris. Recovery tank is full Drain recovery tank. Remove float shut off from inside recovery tank and Float shut off is clogged remove any debris. 11 12 FANG 32T - MAIN FRAME AND DRIVE ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF13501A NUT, M12 6 2 VF13541 WASHER, LOCK, M12 6 VF84118 TIRE, FOAM FILLED, BLACK (OPTIONAL) 2 VF84119 TIRE, BLACK (STANDARD) 2 VF84800 TRANSAXLE, 32" 1 ZD13000 TRANSAXLE MOTOR, 36VDC 1 5 VF13503 NUT, LOCK, M8 1 6 VF84112 PLATE, TRANSAXLE 2 7 VF13517 WASHER, PLAIN, M10 X M26 X 2 14 8 VF13504 NUT, LOCK, M10 12 9 VF84122 CHAIN, STATIC 1 10 VF13535 WASHER, PLAIN, M8 X M20 X 2 1 11 VF14235 SCREW, M8 X 35 1 12 VF14123 SCREW, M10 X 25 12 13 VF13517 WASHER, PLAIN, M10 X M20 X 2.5 8 14 VF84117-1 15 VF84103 FRAME 1 16 VF13634 SCREW, M10 X 30 10 17 VF13518 WASHER, LOCK, M10 10 18 VF84125 BATTERY TRAY 1 3 4 CASTER, 5" 13 2 14 FANG 32T - SCRUB HEAD LIFT ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF84316 PIN, M16 X 30 2 2 VF84317 PIN, M13 X 51 1 3 VF84309 PIN, COTTER, M3 X 60.5 5 4 VF84105 ARM, LIFT, LEFT 1 5 VF13501 NUT, LOCK, M12 2 6 VF13538 WASHER, PLAIN, M12 X M22 X 2 2 7 VF84116 BUSHING 2 8 VF13535 WASHER, PLAIN, M8 X M20 X 2 7 9 VF13519 WASHER, LOCK, M8 7 10 VV13604 SCREW, M8 X 20 7 11 VF84336 BRACKET, BRUSH LIFT 1 12 VF84332 ACTUATOR, 36VDC 1 13 VF84310 BRACKET, ACTUATOR 1 14 VF84322 PIN, M9.5 X 37 1 15 VF14084 PIN, COTTER, M3.2 X 24 1 16 VF84337 ADJUST NUT 1 17 VF84121 ARM, LIFT, RIGHT 1 18 VF14057A NUT, M12 1 19 VF84338 ADJUST SCREW 1 15 16 FANG 32T - SOLUTION TANK ASSEMBLY DIA NO PART NUMBER DESCRIPTION 1 VA13477 SCREW, SELF-TAPPING, ST, M4 X 16 4 NO REQ'D 2 VV13664 WASHER, PLAIN, M4 X M12 X 1 2 3 VF82154 EXPANSION PLUG 1 4 SCREW, M8 X 20 WASHER, LOCK, M8 8 5 VV13604 VF13519 6 VF13535 WASHER, PLAIN, M8 X M20 X 2 8 7 BUSHING SUPPORT, RECOVERY TANK 1 8 VF81406 VF81404 1 9 VF46454 FILTER, INTAKE TANK 1 10 VF84340 PLUG,EXPANSION 1 11 VF82029A BRACKET, VAC TUBE 1 8 12 VF82032 SPRING 1 13 VF82030 ADAPTER, TUBE 1 14 VF82031A GASKET, TUBE ADAPTER 1 15 VF14230 SCREW, M5 X 16 2 16 VV13601 WASHER, LOCK, M5 2 17 VF13532 WASHER, PLAIN, M5 X M11 X 2 2 18 VF84140 BRACKET, DRAIN HOSE 1 19 VF82123 DECAL 1 20 VF84135 WIRE, #4 X 600, RED 1 21 VF84148 WIRE, #4 X 600, BLACK 1 22 VF14232 SCREW, M6 X 10 2 23 VV13607 WASHER, LOCK, M6 8 24 GT13032 WASHER, PLAIN, M6 X M16 X 1.5 8 25 BRACKET CONNECTOR, GREY, 175A 1 26 VF84109 VF81306G 27 VF13633 SCREW, M6 X 35 2 28 VF13495 SCREW, M6 X 16 4 29 VF81715 STANDOFF 2 2 30 VF13502 NUT, LOCK, M6 2 31 VA85003 KNOB, M8 4 32 VF84111 SCREW, M8 X 35 4 33 VF84101 SOLUTION TANK 1 VF84127 VF84132 BATTERY, 6V, 305AMP HOUR CABLE, BATTERY 6 VF81724 CAP, BATTERY, BLACK 2 34 35 36 5 VF81724R CAP, BATTERY, RED 2 37 VF84128 CHARGER, 36V, 30AMP 1 38 VF14234 SCREW, M8 X 16 2 39 VF13513 NUT, M8 2 VF81408 VF82090 PLATE, LOCK CLAMP (16-25) 2 43 VF84138 VF14248 TUBING SCREW, M8 X 100, OPTIONAL 1 44 VA13516 WASHER, PLAIN, M10 X M30 X 1.5, OPTIONAL 1 45 VF84224 PU BLADES & FASTEN KIT, OPTIONAL 1 46 47 VF84137 HOSE BARB, G 1/2 2 VF82070 LABEL,LEFT 1 48 VF82071 LABEL,RIGHT 1 40 41 42 17 1 1 18 FANG 32T - RECOVERY TANK ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF82010 CLEAR COVER, RECOVERY TANK 1 2 VF82083 DECAL, BATTERY WARNING 1 3 VF82009 ELBOW ADAPTOR, FLOAT 1 4 VV13607 WASHER, LOCK, M6 14 5 VF13533 WASHER, PLAIN, M6 X M16 X 2 7 6 VF14233 SCREW, M6 X 20 4 7 VF81504 FLOAT 1 8 VF84102 RECOVERY TANK (32") 1 9 VF81509 EXPANSION PLUG 1 10 VF81510-9 STRAP, DRAIN HOSE 1 11 VF81510-2 SLEEVE, DRAIN HOSE 1 12 VF81510-1 DRAIN HOSE 1 13 VF81510A DRAIN HOSE ASSEMBLY 1 14 VV10113 CLAMP, 2" 2 15 VF84124 DECAL, BATTERY INSTALLATION 1 16 VF14235 SCREW, M8 X 35 1 17 VF13535 WASHER, PLAIN, M8 X M20 X 2 2 18 VF84107 BRACKET, DROP ARM 1 19 VF84133 BUSHING 1 20 VF84216 BUSHING 1 21 VA13491 SCREW, M8 X 25 1 22 VF13521 NUT, M6 3 23 ZD60000 MOTOR, VACUUM, 3 STAGE, 36VDC 1 24 VF81508 STUD (24") 3 25 VF13502 NUT, LOCK, M6 3 26 VF81503 SEAT 1 27 GT13032 WASHER, PLAIN, M6 X M16 X 1.5 10 28 VF14200 SCREW, M6 X 16 10 29 VF84113 HINGE, RECOVERY TANK 2 30 VF83143 LOGO (32") 1 31 VA13477 SCREW, SELF-TAPPING, ST, M4 X 16 4 32 VV13664 WASHER, PLAIN, M4 X M12 X 1 4 33 VF82010A RUBBER HINGE 1 34 VF82010B GASKET 1 35 VF82010-X KIT, LID 1 19 20 FANG 32T - SCRUB HEAD ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF84315 BRACKET, SPRING 1 2 VF13615 WASHER, PLAIN, M13 X M30 X 2 4 3 VF84312 SLEEVE 2 4 VF84313 ZD11000 SPRING BRUSH, MOTOR, 36VDC, 1HP 2 2 ZD45407 KEY, 6.35 X 25 2 BOLT, SHOULDER, 1/4" X 4.25" X 3/8" BRACKET, BRUSH LIFT 2 7 VF84311 VF84335 1 8 VF84314 SPRING 2 9 VF84304 BRACKET, SPRING MOUNT 1 10 VF14235 SCREW, M8 X 35 4 11 VF14251 SCREW, M8 X 30 4 12 VF84305A BRACKET, LIFT, RIGHT 1 13 VF82090 CLAMP, (16-25) 2 5 6 14 VF84333 TUBING, 17.5mm ID, 145mm 1 15 VF84141 HOSE BARB, TEE 1 16 VF84334 TUBING, 11.5mm ID, 135mm 1 17 VF84345 TUBING, 11.5mm ID, 125mm 1 18 TUBING,11.5mm ID, 275mm BRACKET, LIFT, LEFT 1 19 VF84346 VF84303 1 20 VV20509 SCREW, M5 X 10 4 21 VF84325 DOOR, SCRUB HEAD 2 22 VF82042 ELBOW 2 23 VF82148 CLAMP, 16mm 6 24 VF82138 TUBING, 11.5mm ID, 75mm 1 25 VF84146 HOSE BARB 2 26 27 VF84302 VF84323 COVER, SCRUB HEAD SKIRT, SCRUB HEAD 1 28 VF14310 SCREW, M5 X 70 1 29 VF84324 CLAMP, SKIRT 1 30 BRUSH, 15 INCH WASHER, PLAIN, M8 X M20 X 2 2 31 VF84330 VF13542 9 32 GT13022 NUT, LOCK, M5 1 33 VF13503 NUT, LOCK, M8 8 34 VF13537 WASHER, PLAIN, M10 X M26 X 2 8 35 VV13620 WASHER, LOCK, 3/8" 8 36 VF14242 SCREW, 3/8"-1" 10 37 VF13545 SCREW, SELF-TAPPING, ST, M5 X 10 8 38 VV13601 WASHER, LOCK, M5 8 39 VF83134 STOP, DRIVE RELEASE 2 40 VF83130 PLATE, DRIVE 2 41 VF83130A PLATE, DRIVE, ASSY 1 42 VF82058 VV20298 WASHER WASHER, LOCK, 5/16" 2 43 21 1 2 FANG 32T - SCRUB HEAD ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 44 VF14241 SCREW, 5/16" - 1" 2 45 VF84329 PAD DRIVE, 15 INCH 2 46 VA13484 SCREW, SELF-TAPPING, ST, M4 X 12 6 47 VF99003A BIG MOUTH 2 48 MF-VF002-4A SCREW, SELF-TAPPING, 1/4" - 1" 6 49 VF83118 SPACER 2 50 VF83132 SPRING 2 51 VF83131 CLAMP, BRUSH PLATE 2 52 VF13502 NUT, LOCK, M6 6 53 VF83133 STUD 6 54 VF14225A VF84134 SCREW, M6 X 40 PUSH SCREW 6 55 7 56 VF82013 WHEEL, 3" 6 57 VF82055 BUSHING 6 58 VF13514A WASHER, PLAIN, M8 X M16.5 X 1 6 59 VF14248 SCREW, M8 X 100 2 60 VF84104 COVER, FRONT 1 61 VF84326 NUT, LOCK, 3/8" 2 22 23 FANG 32T - SQUEEGEE AND SQUEEGEE LIFT ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF13503 NUT,LOCK,M8 2 2 VF84220 BRACKET,SQUEEGEE LIFT 1 3 VF13514 WASHER,PLAIN, M8 X M16.5 X 1.5 1 4 VF48222 BUSHING 2 5 VF84218 ARM,SQUEEGEE LIFT 1 6 VF82159 BUSHING 1 7 VF14096 PIN, M2 X 20 1 8 VF82158 SHAFT 1 9 VF13535 WASHER,PLAIN, M8 X M20 X 2 5 10 VF14235 SCREW,M8X35 1 11 VF84217 HANDLE, LIFT 1 12 VA13491 SCREW,M8X25 1 13 VF48310 GRIP,HANDLE 1 14 VF84219 -1 CABLE,SQUEEGEE,LIFT (32") 1 15 VF84226 FRONT SQUEEGEE SUPPORT 1 16 VF13637 SCREW, M12 X 130 1 17 VF84229 LOCK SPRING 1 18 VF84223 HOSE 1 19 VF14547 NUT,LOCK,M10 1 20 VF85336 WASHER,NYlON 4 21 VF84225 BACK SQUEEGEE SUPPORT 1 22 VF14527 SEREW,SHOULDER M10 1 23 VF13521 NUT, M6 1 24 VF83150 HOLDER,"U" HOSE 1 25 VF13519 WASHER,LOCK,M8 3 26 VV13604 SCREW,M8 X 20 3 27 VF13514A WASHER,PLAIN, M8 X M16.5 X 1 2 28 VF82055 BUSHING 2 29 VF82013 WHEEL, 3" 2 30 VF84202 HOUSING,SQUEEGEE (FANG 32T) 1 31 VF84208 BLADE,SQUEEGEE,REAR,NEOPRENE (FANG 32T) 1 32 VF81218 LATCH,HOOD 1 33 VF81209 HOOK,REAR SQUEEGEE BACKUP ADJUSTMENT 1 34 VF14310 SCREW, M5 X 70 1 35 VF81208 RIVET, M4 X 5 2 36 GT13022 NUT,LOCK, M5 1 37 VF81222 BOLT,SHOULDER, 5/16" X 1.25" 3 38 VF81219 WHEEL, 2" 3 39 VV20203 NUT,LOCK, 5/16" 3 40 VF84206 BACKUP STRIP,SQUEEGEE,REAR (FANG 32T) 1 41 VF14236 SCREW,M8 X 40 2 42 VF84206A KIT,BACKUP STRIP,SQUEEGEE 1 43 VF84207 BLADE,SQUEEGEE,FRONT,PU (FANG 32T) 1 44 VF84205 BACKUP STRIP,SQUEEGEE,FRONT (FANG 32T) 1 45 VF82121 KNOB, M6 6 46 VF84200 SQUEEGEE ASSEMBY (FANG 32T) 1 47 VF13502 NUT,LOCK, M6 1 48 VF13501 NUT,LOCK, M12 1 49 VF84228 SEREW,SHOULDER M8 2 50 VF84227 SQUEEGEE SUPPORT 1 51 VF81210 KNOB,M8 2 52 VF13538 WASHER,PLAIN, M12 X M26 X 2 1 53 VF14516 NUT,LOCK,M8 2 54 VF13542 WASHER,PLAIN, M8 2 55 VF85104 HANDWHEEL M8X55 1 56 VF85103 SQUEEGEE SUPPORT PIN 1 57 VF14503 NUT HEX LOW M8 2 58 VF85106 SPACER 8X10X7 1 59 VF84230 KIT,SQUEEGEE BRACKET ASSEMBY 1 24 25 FANG 32T - SOLUTION CONTROL ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF14245 SCREW, M5 X 6 2 2 VF82036 SHAFT 1 3 VV13650 SCREW, M4 X 10 1 4 VF13532 WASHER, PLAIN, M5 2 5 VV13601 WASHER, LOCK, M5 2 6 VF14230 SCREW, M5 X 15 2 7 VF13536 WASHER, PLAIN, M9.8 X M16 X 1 2 8 VF82075 NUT, 3/8" 2 9 VF84123 CABLE, SOLENOID 1 10 VF82148 CLAMP, 16mm 4 11 VF84141 HOSE BARB, TEE 1 12 VF84333 TUBING, 11.5mm ID, 125mm 1 13 VF81403A ELBOW, SOLUTION TANK 2 14 VF84341 TUBING, 17.5mm ID, 50mm 1 15 VF84142 CONNECTOR, NPT 1/2" 1 16 VF84144 BALL VALVE, 15mm DN, NPT 1/2" 1 17 VF82168-3 SEAT, FILTER 1 18 VF82168-4 SCREEN, 80SS, FILTER 1 19 VF82168-5 GASKET, FILTER 1 20 VF82168-2 COVER, FILTER 1 21 VF82168 FILTER, ASSY 1 22 VF84347 TUBING, 17.5mm ID, 185mm 1 23 VF84143 ELBOW 1 24 VF82090 CLAMP 6 25 VF84342 TUBING, 17.5mm ID, 150mm 1 26 VF13495 SCREW, M6 X 16 2 27 VF13533 WASHER, PLAIN, M6 X M16 X 2 2 28 VF84120A SOLUTION VALVE SOLENOID, 36VDC 1 29 VF13502 NUT, LOCK, M6 2 30 VF84348 TUBING, 17.5mm ID, 350mm 1 31 VV20509 SCREW, M5 X 10 2 32 VF81118 CLAMP 2 33 VF13540 WASHER, WAVE, M12 1 34 VF82037 BRACKET, DRAIN HOSE & VALVE 1 35 VF82069 LABEL, VALVE 1 36 VF82074 BUSHING 1 37 VF82038 KNOB, VALVE ADJUST 1 26 27 FANG 32T - CONTROL HOUSING DIA NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 PART NUMBER DESCRIPTION VF84703 VF13491 VF14122 BUSHING SCREW, M4 X 12 WASHER, PLAIN, M10 X M20 X 2 VF14121 VF13502 GT13032 VF81781 SCREW, M10 X 65 NUT, LOCK, M6 WASHER, PLAIN, M6 DIODE, 400V VF84716A VF13495 VF84145 VF84701 VF14078 VA50477 VF84711 VF84717 VF81719 VF84702 VF84704 VF81727 VF81725 VF84722 VF14200 SOLENOID, 36V SCREW, M6 X 16 TIMER HOUSING, CONTROL SCREW, M3 X 10 WASHER, PLAIN, M3 X M10 X 1 GASKET LIGHTS,BATTERY CAPACITY SPACER LABEL, SWITCH (FANG 32T) PANEL, SWITCH (32") GAUGE, BRUSH PRESSURE SWITCH, BRUSH LIFT SWITCH, LIGHTED ROCKER SCREW, M6 X 16 VF81730 VF82305 VF84710 VF81716 VF81710 VF81729 VF84718 VF84719 VF84712 VF84713 KNOB, SPEED CONTROL LABEL, SPEED CONTROL PIN, HANDLE LOCK SPRING PIN, HANDLE ADJUSTMENT POTIENTIOMETER, 4.7K PLATE BOARD, SPEED CONTROL LABEL, CIRCUIT BREAKER SERIAL TAG VF84705 VF84715 VF84723 PANEL, CONTROL HOUSING LABEL, CIRCUIT BREAKER CONTROL BOARD, BATTERY CAPACITY VF99012 VF84708 VF81711 BREAKER, CIRCUIT, 12 AMP HANDLE, RIGHT BOLT, SHOULDER, M8 X 15 X M6 VF84707 VF81712 VF13514A VF14212 VF13511 VF44203 VF84706 VV13652 VF84709 VF82153 VF82160 VF84721 VF81722 VF81734 HANDLE, LEFT SPRING WASHER, PLAIN, M8 X M16.5 X 1 SCREW, M3 X 25 WASHER, TOOTH, M3 SWITCH ASSEMBLY BRACKET, SWITCH (32") NUT, LOCK, M3 TUBE, HANDLE, ADJUSTMENT KEY SWITCH LABEL, KEY SWITCH CORD STRAIN RELIEF SWITCH, TOGGLE BREAKER, CIRCUIT, 35 AMP 28 NO REQ'D 2 7 2 2 10 6 3 3 12 1 1 6 6 1 1 6 1 1 1 1 3 12 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 2 2 2 1 1 2 1 1 1 1 1 3 BATTERY CAPACITY LIGHTS 0 0 0 7 21 HOUR METER VACUUM SWITCH 0 8 6 BRUSH SWITCH 5 8 (16AWG GRN) 0 0 0 6 SOLUTION SWITCH 22 6 5 TRIGGER SWITCH 5 (16AWG WHT) (16AWG WHT) 5 KEY SWITCH DRIVING MOTOR SPEED CONTROLLER UP 17 18 DOWN ACTUATOR F R DIRECTION SWITCH (16AWG WHT) 3 5 5 0 B+ B- M2 M1 1 9 4.7K 2W 13 (14AWG RED) 01 (14AWG BLK) 16 (14AWG BLK) 15 (14AWG RED) 18 (16AWG BLU) 17 (16AWG BLU) 1 (16AWG WHT) 12 (12AWG RED) 1 3 12A 12 CIRCUIT BREAKER 11 35A RITHT BRUSH CIRCUIT BREAKER 0 (16AWG BLU) 0 (16AWG BLU) 0 (16AWG BLU) 0 (16AWG BLU) 22 10 (12AWG RED) 10 (12AWG RED) 11 (12AWG RED) 8 (16AWG GRN) 2 (16AWG GRN) (12AWG RED) 11 BRUSH SOLENOID 7 0 12 (12AWG RED) 12 35A AMMETER 11 SOLUTION SOLENOID 17 (16AWG BLU) PCB 5 0 B+ B- ACTUATOR MOTOR 12 (12AWG RED) LEFT BRUSH CIRCUIT BREAKER 0 (16AWG BLU) 0 (16AWG BLU) 18 (16AWG BLU) 03 (12AWG BLK) LEFT BRUSH MOTOR 12 (12AWG RED) 03 (12AWG BLK) RIGHT BRUSH MOTOR 21 (16AWG WHT) 20 (14AWG RED) 14 (14AWG RED) 04 (14AWG BLK) 19 23 0 20 (14AWG RED) 20 35A 19 (14AWG RED) VACUUM MOTOR VACUUM SOLENOID 15 (14AWG RED) DRIVE MOTOR 9 (14AWG RED) VACCUM MOTOR CIRCUIT BREAKER (4AWG RED) + _ 6V BATTERY + _ 6V BATTERY + (4AWG RED) 14 (14AWG RED) (4AWG BLK) 5 (16AWG WHT) 0 (16AWG BLU) 0 (16AWG BLU) 01 (14AWG BLK) 9 13 (14AWG RED) 02 (16AWG GRN) MAIN SOLENOID 03 (12AWG BLK) _ + 6V _ BATTERY 10 (12AWG RED) 10 (12AWG RED) _ _ + 6V _ BATTERY 1 (16AWG WHT) + + 6V _ BATTERY + + 6V _ BATTERY 16 (14AWG BLK) (4AWG BLK) 03 (12AWG BLK) 04 (14AWG BLK) 0 (16AWG BLU) 29 0 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Author : Ricky yang Create Date : 2011:03:04 14:26:54+08:00 Modify Date : 2016:03:15 10:13:05-05:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:03:15 10:13:05-05:00 Creator Tool : Adobe Acrobat 8.0 Combine Files Format : application/pdf Title : E:\\FANG32T-UVF84902\top page Model (1) Creator : Ricky yang Document ID : uuid:d7d49669-6288-4a2f-ae4b-f43443822b28 Instance ID : uuid:b53017da-62ae-41f1-b0b7-25948a67aefe Producer : Acrobat Distiller 8.0.0 (Windows) Page Count : 29EXIF Metadata provided by EXIF.tools