Sweepscrub Kaercher B 140 R Rider Scrubber Quick Start Guide OBJ_DOKU 101441 001 User Manual

User Manual: Sweepscrub Kaercher-B-140-R-Rider-Scrubber-Quick-Start-Guide kaercher-b-140-r-rider-scrubber-quick-start-guide 2352 file product_file sweepscrub

Open the PDF directly: View PDF .
Page Count: 5

QUICKSTART

5.964-043.0 03/12

Warning

These are only brief instructions! Please read and comply with these instructions prior to using or servicing your

appliance.

The non-compliance of the operating and safety instructions may lead to damages of the appliance and to dangers

for the operator and other persons.

Start up

1AA Check if the battery plug is connected to the

appliance.

2A B A Sit on the driver's seat.

Set main switch to “1”.

B Check battery status.

Note

The device is equipped with a safety mechanism

to prevent total discharge, i.e. when the permissi-

ble minimum capacity is reached, then the ma-

chine can only be driven and existing lamps can

be switched on. In such a case, the battery mon-

itoring symbol on the control console glows red.

Drive the machine directly to the charging

station; avoid any steep gradients in the

process.

3A B A Loosen the star handle screws.

B Push the seat back into the desired position.

Tighten star handle screws.

4A

D

B C A Place the detergent bottle into the device.

Close the bottle lid.

Insert the suction hose of the dosaging

equipment into the bottle.

B Open the cover of the fresh water reservoir.

C Fill up fresh water (maximum 60 °C) until the

lower edge of filling nozzle.

Close the cover of the fresh water reservoir.

Model without dosing equipment "Dose"

D Pour in detergent.

Close the cover of the fresh water reservoir.

B140R

QUICKSTART

5.964-043.0 03/12

Operation

1AStarting the machine

A Sit on the seat and set main switch to "1".

2A

D

B

E

CDriving

A Set programme switch to step 1 (driving).

B Drive forward

Set the drive direction using the drive

direction button at the operator console.

C Reverse drive

Set the drive direction using the drive

direction button at the operator console.

D Determine the driving speed by pressing

the drive pedal.

E Stop the machine: Release the drive pedal.

3Cleaning Programs

AScrubbing suction

Wet clean the floor and vacuum up dirt water.

BWet scrubbing

Wet clean the floor and allow the detergent

to react.

CVacuuming

Vacuum the wastewater.

DPolishing

Polishing the floor without the application

of liquid.

EScrub the floor without applying water

(vacuum polishing)

Polish the floor without applying any fluid and

suck in the polishing dust.

FManual cleaning

Apply liquid detergent using the wall-ceiling-

floor nozzle (optional) and vacuum it again.

4AInfo button

Use the Info button to select the menu items

and do the settings.

A Turning the button to the right/left scrolls

through the menus forward/ backward.

The selected setting gets accepted by

pressing the button.

QUICKSTART

5.964-043.0 03/12

5ASwitch on the dosing equipment for

detergent (optional)

A Activate the switch for detergent dosing.

Detergent gets added automatically.

Finish operation

1AEmptying waste container

A Only BR model: Remove bulk waste

container and empty it.

2A

CD

BEmpty tanks.

몇Warning

Please observe the local provisions regarding

the wastewater treatment.

A Take the water discharge hose from the

support and lower above a suited collection

device.

B Rinse the dirty water tank with clear water.

Take the water discharge hose from the

support and lower above a suited collection

device.

Leave the cover open to let it dry.

C Remove the suction hose coupling for

draining off the fresh water and hold it over

a suitable container.

D Select the cleaning program "manual dry"

via the program switch.

3ACharging battery

A Tilt the dirt water tank backwards.

Remove battery plug and join it to the

charging cable.

Connect the charger to the mains and turn

it on.

Operation

QUICKSTART

5.964-043.0 03/12

Maintenance and care

daily

monthly

Kärcher Customer Service

1AA Check the fluff filter, clean if

required

2A B A Clean the vacuum lips and the

wiping lips, check for wear and

replace if required.

B Clean the suction channel.

3AA Check brush for wear and tear and

clean it.

Check the brushes for wear (bristle

length at least 10 mm), replace if

required.

4Only with R cleaning head Remove

bulk waste container and empty it.

5Clean the outside of the appliance with

a damp cloth which has been soaked in

mild detergent.

6AA Clean the seals between dirt water

reservoir and cover and check for

tightness, replace if required.

7Have the prescribed inspection carried

out by the customer service.

QUICKSTART

5.964-043.0 03/12

Troubleshooting

1AB C Appliance cannot be started

A Insert battery plug.

B Safety switch not activated, sit down on the

seat. Set main switch to “1”

C Check battery; charge it if required.

2A

D

B C Insufficient vacuum performance

A Clean the seals between dirt water reservoir

and cover and check for tightness, replace if

required.

B Check the fluff filter, clean if required

C Clean the vacuum lips on the vacuum bar,

turn or replace if required.

D Check suction hose for blockages;

clean if required.

Check connection between suction hose and

suction bar and suction hose and wastewater

tank.

3AInsufficient cleaning result

A Check brush for wear and tear and clean it.

Check the brushes for wear (bristle length at

least 10 mm), replace if required.

4ABCInsufficient water quantity

A Check fresh water level, refill tank if

necessary.

B Check that the hose coupling for

draining the fresh water is connected.

C Clean the fresh water filter.

Open the ball tap.

5ABrushes do not turn

A Reduce contact pressure.

–Check the brushes for blockage due to

foreign particles, remove them if found.

–Motor overload, allow to cool down. Set the

key switch to "0". Wait approx. 10 minutes

before turning the key switch to "1" again.