983211, 170 El.p65 Minuteman Electric Walk Behind Floor Scrubber Parts And Operator Manual
2018-04-26
: Sweepscrub Minuteman-170-Electric-Walk-Behind-Floor-Scrubber-Parts-And-Operator-Manual minuteman-170-electric-walk-behind-floor-scrubber-parts-and-operator-manual 2712 file product_file
Open the PDF directly: View PDF .
Page Count: 19
Download | ![]() |
Open PDF In Browser | View PDF |
170 Electric Floor Scrubber OPERATION Revised 8/03 SERVICE Model: MC17115-00 MC17230-00 MC17230-00CE PARTS CARE FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING - To reduce the risk of fire, electric shock, or injury: Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing, cleaning or maintaining. WARNING To reduce the risk of electric shock - Do not expose to rain. Store indoors. • Do not allow to be used as a toy. Close attention is necessary when used by or near children. • This machine shall be used only by instructed and authorized persons. • Use only as described in this manual. Use only manufacturer’s recommended attachments. • Inspect cord regularly. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center. Use only cord specified by manufacturer. • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces. • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • Do not handle plug or appliance with wet hands. • Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow. • Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. • Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. • Do not use without dustbag and/or filters in place. • Turn off all controls before unplugging. • Use extra care when cleaning on stairs. • Do not use to pick up flammable or combustible liquids such as gasoline or use in areas they may be present. • Connect to a properly grounded outlet only. See grounding instructions. • This machine is not suitable for picking up hazardous dust. • Close tank and lid before use. SAVE THESE INSTRUCTIONS 1 INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately. WARNING • Read Instruction Manual before operating this piece of equipment. • To reduce the risk of fire use only commercially available floor cleaners and waxes intended for machine application. • To reduce the risk of electrical shock, do not expose to rain. Store indoors. • Do not cross over supply cord, hazard exists when rotating brush crosses over the cord. • Electrical motors and components can cause an explosion when operated near volatile materials and vapors. Do not use this machine near flammable materials such a solvents, thinners, fuels, grain dust, etc. ELECTRICAL (Model MC17115-00) This floor machine is designed to operate on a standard 15 amp. 120 volt, 60 hz, AC circuit. Voltages below 105 volt AC or above 125 volts AC could cause serious damage to the motor. (Model MC17230-00) This machine is designed to operate on a standard 16 amp type L fused 230 volt, 50 hz, AC circuit. Voltages below 200 volts AC or above 250 volts AC could cause serious damage to the motor I.E.C. Class 1. GROUNDING INSTRUCTIONS • This floor finishing machine should be grounded while in use to protect the operator from electric shock. The machine is equipped with a three-prong grounding type attachment plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect this wire to other than the grounding blade. • Floor Finishing Machines Rated Less Than 150 Volts - If the machine is provided with an attachment plug as shown in Sketch A it is intended for use on a 120-volt (nominal) circuit. If a properly grounded receptacle as shown in Sketch A is not available, an adapter as shown in Sketch C is available and should be installed as shown in Sketch B if the outlet box that houses the receptacle is grounded. Be sure to fasten the grounding tab with the faceplate 2 1. Squeegee left lever 6. Drain hose for clean solution tank 2. Vacuum switch 7. Drain hose for recovery tank 3. Power cable hook-up 8. Vacuum recovery hose 4. Brush switch 9. Power assist control 5. Solution control lever 10. 3 Foot pedal for lower/raising brush BRUSH REMOVAL Unplug machine. Empty solution and recovery tanks. Remove squeegee assembly. Lower brush. Tilt machine as shown (figure 3) until machine rests on foot pedal. Brush has a snap-on push off clutch plate. Pushing brush away from the machine from the side, will release brush assembly. To install: Hold brush in the center and snap on to drive hub. 4 OPERATING INSTRUCTIONS 1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution to the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely to dissolve thoroughly, resulting in clogging the in-line solution filter. This can reduceor stop water flow to the brush. 2. Lower brush assembly. - To lower the brush, first push the pedal slightly towards the center of the machine (unlock it), then release it slowly. - To lift the brush, press the pedal down until lift mechanism engages. 3. Turn on brush switch. 4. Adjust solution control feed lever. 5. Turn on vacuum switch. 6. Lower squeegee assembly. After Use: 1. Turn off solution feed. 2. Switch off brush and raise. 3. Raise squeegee assembly. 4. Turn off vacuum motor. Solution and recovery tanks should be emptied after every use. MAINTENANCE: Daily 1. Clean float assembly & squeegee blades. 2. Wipe down outside of machine with damp cloth. Monthly 1. Check wear on squeegee blades. 2. Grease rear wheels. 3. Grease pivot points on brush motor assembly. Every 500 hours check condition of carbon brushes on vacuum motor and brush drive motor. 5 6 Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part No. 430000MCH 430001MCH 430002 430044 430046 430049 430126 430136 430141 430142 450021 711104 711161 712536 712560 712822 430126 Qty. Description 1 1 1 2 2 1 2 1 1 1 1 3 18 6 6 6 2 Base Assy. 17 B/E Machined 170 Sol./Recovery Tank Assy. Cover Poly 170 Burgundy Hinge Lid 17 B/E Side Skirt Retainer 17 Splash Skirt 17 B/E Hinge Backing Plate Gasket Seal Kit (4) Splash Skirt 170 Mounting Bracket Hinge SCR-ST-A #10 x .50 SCR-Hi/Lo #10 x 3/4 PL SCR-MC 10-24 x .62 SS SCR-MC 1/4-20 x .50 SS SCR-THMS 10-24 x .50 STPL Hinge Backing Plate 7 8 Parts List Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 130118 200173 210401 210409 210410 210414 260203 430001MCH 430037 430038 430050 430089 430090 430098 430116 430121 430199 450076 450081 450083 710353 710985 711504 711513 712092 712568 712667 760343 762331 762384 828970 828971 829559 830062 833316 Qty. 1 1 1 2 2 2 1 1 2 2 1 1 1 1 1 1 1 1 2 2 2 2 1 2 1 1 1 1 2 2 1 1 1 2 1 Description Solution Strainer Float Housing Solution Hose Fitting Brass 3/8 MPT 3/8 FPT Fitting Brass 3/8 FPT 3/8 Barb O-Ring 2-113 Hose Clamp 170 Sol./Recovery Tank Bumper Wheel Axle U Bracket Wheel Mount Filter Screen 4 x 4 Float 17B Float Valve Weldment Vac Recovery Hose 22 C/L Hose 3/8 Nylo 34” Standpipe Assy. 170/175 Hose White Wireloc 24” Crimp Clamp SS 185R WSR SS 1.908 x 2.41 x .03 Insert Fitting SCR-MC 10-32 x .37 STPL SCR-SC 3/8-16 x .62 WSR-Flat 1/4 ID SS WF .689 x 1.06 x .029 SS SCR Nylon 1/4-20 x 2.5 SCR-MC 1/4-20 x 2.25 SS Nut-Hex 1/4-20 SS Nyloc Tjube Hose 24/32B Wheel, 2.5D x 1.28W x .38ID Bushing SS .277 x .375 x .37 WSR Neop 1.87 x 2.4 x .125 Nut 1 1/2 Pipe Thread Cable Assy. 170/175 Fitting Brass 90 3/8 MPT Drain Plug 9 10 Parts List Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27A 27B 28 29 30 31 32 33A 33B 33C 33D 34 35 36 37 38 39 40 41 42 43 44 45 46 47 250041 831001 290017 430018 430029 430042 430138-1 430069 828264 430099 450038 460019 710178 712129 711106 711161 711210 711243 711380 711425 711439 711506 711509 430149 711515 712090 740429 741030 210083 829067 762398 801013 832136 430034 430108 430108 430108 710986 364-816 711510 828301 210401 342430 711513 210370 828975 829463 809413MCH 450040 711106 450076 Qty. 1 2 1 2 2 1 2 1 1 1 1 1 6 3 3 5 3 6 8 3 2 3 4 4 6 2 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 1 1 1 1 1 1 1 3 1 Description Seal, Rubber Crimp Clamp 440R Molded Vac Mtr. Gasket Z Bracket Caster Caster Mounting Bracket Wheel 6” Vacuum Manifold Assembly Spring Washer Cup Vacuum Hose Z Bracket Gasket 3.75 x 5.75 x .75 SCR-MC 1/4 - 20 x .50 STPL SCR-TR 1/4-20 x 1.00 HWH SCR-ST-A 10 x .75 PL SCR Hi/Lo #10 x 3/4 PL BLT-HH 1/4 - 20 x 1.25 STPL BLT-HH 3/8 - 16 x 1.5 STPL Nut-Nyloc 3/8 - 16 Nut-Flanged Wizz 1/4 - 20 Nut-Flanged Wizz 3/8 - 16 WSR-Flat 5/16 STPL WSR-Flat 1/2 Bushing .531 x 1 x .25 SS WSR-Flat .406 x .812 x .062 Shoulder Blt. 1/2 x 3.5 Vac Motor 220V (115V Model Only) Vac Motor 240V Adjusting Rod Weldment Crimp Clamp 560R Hose, Rubber Flex 2 x 13 Sleeve, Hose Nylon Sleeve Sol. Feed Nylon Brush Pad Driver Poly Grit Brush Strato Grit Brush SCR-SC 3/8 - 16 x 1.00 Nut-Nyloc 1/2 Washer Spring Solution Hose Fitting Brass 3/8 MPT 3/8 Barb WSR-Flat .689 x 1.06 x .029 Solution Valve Bracket WSR-Neo .75 x 1.50 x .09 WSR-Flat .75 x 2.00 x .05 Solution Valve Elbow 3/8 MPT x 3/8 Barb SCR-ST-A 10 x .75 PL Crimp Clamp SS 185R 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Part No. 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 2 1 1 1 2 5 430014 430019 430022 430025 430026 430030 430035 430051 430054 430055 430056 711579 711420 430064 430065 430066 430067 430080 430081 430088 430116 430106 430113 430114 430118 450076 710986 Description 100000 430003 430009 Qty. Motor Lift Weldment Speed Control Weldment Control Pivot Weldment Speed Control Rod Speed Control Weldment Squeegee Mount Weldment Drive Hub Return Spring Pivot Cam 17 B/E Threaded Connecting Rod Compression Spring WSR-Flat .56 x 1.00 Nut-Hex Jam 5/16-18 STPL Wheel Mount U Strut Right Mtg. Plate Wheel Carriage Squeegee Return Spring L Squeegee Return Spring S Balljoint (SP1002) Wheel Mount U Strut Left L Bkt. Motor Lift Hose 3/8 Nylo x 34" Stabilizer Bar Lower Hose 3/8 x 1.375 Nylon Cap 1/4 FPT HC4 Clear Dump Hose C/L 22" Crimp Clamp SS 185R SCR-SC 3/8 - 16 x 1.00 STPL Mounting Bkt. Quick Disc. Motor Mount Weldment Motor Brkt. Weldment 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 51A 53 54 55 56 57 58 59 60 61 Item Parts List 711202 711227 711246 711374 711379 711380 711425 711439 711506 711515 320268 711517 711523 711544 711615 711803 712042 712569 712666 740428 740432 760592 210142 828952 833325 833473 715136 711505 711373 210066 Part No. 10 1 1 1 3 1 4 1 3 2 1 3 2 9 1 2 3 3 2 1 1 2 1 1 1 1 1 3 1 1 Qty. BLT-HH 1/4 - 20 x .50 STPL BLT-HH 5/16 - 18 x .62 BLT-HH 3/8 - 16 x .87 STPL Nut-Nyloc 5/16 - 18 Nut-Flanged Wizz 5/16 - 18 Nut-Nyloc 3/8 - 16 Nut-Flanged Wizz 1/4 - 20 Nut-Flanged Wizz 3/8 - 16 WSR-Flat 5/16 STPL WSR-Flat .44 x .87 x .07 Key 1/4 x 5/16 x 1 WSR-Flat .77 x 1.37 x .03 WSR-Wave .37 x .68 x .02 WSR-Helical 1/4 Rollpin .12 x .75 Cotter Pin .06 x .75 Drive Hub Retainer Bolt Bolt-WSR HH 5/16-18 x .62 Nut-Hex Jam 1/4 - 28 SS Gearmotor 115V Gearmotor 230V Knob Oval Tapered Pedal Pad Fitting 1/4 MPT x 3/8 Barb Fitting Nylon 90° 1/4 MPT Fitting Brass 1/4 FPTx 3/8 Barb Decal Diecut Speed Control WSR-Flat 1/4 Nut-Nyloc 1/4-20 Drive Hub Retainer Bolt Description 14 15 Part No. 430123 430039SP 430039CESP 430052 430053 430059 430060 430070 430073 430074 430076 11-145 430078 430079 430085 740202 430105 430103 710180 711126 711124 711161 711128 711352 711425 711503 711506 711523 Item 1 2 2A 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 1 1 1 1 1 1 1 1 1 6 2 1 1 1 2 1 1 1 2 1 2 6 3 1 6 2 2 1 Qty. Rear Cover Dashboard 170 Screen Printed Dashboard 170CE Screen Printed Squeegee Lift Cable Assy. Solution Control Cable A Squeegee Lift Brkt. Assy. Squeegee Lift Arm Assy. Squeegee Mount Assy. Gasket Diecut PS Back Adjusting Nut 17 B/E Nylon Squeegee Insert Squeegee Gum Rubber U Profile Casting Squeegee Assy. Squeegee Bumper Wheel Rectifier Bridge 50A 600V Clevis Pin .312 x 1.75 Spring Hook SCR-MC 1/4 - 20 x .75 STPL SCR-ST-B 10 x .75 SCR-ST-B #10 x .37 NI SCR-Hi/Lo #10 x 3/4 PL SCR-ST-B Hi/Lo 8 x .62 PL Nut-Acorn 1/4 - 20 ST NI Nut-Flanged Wizz 1/4 - 20 WSR-Flat #10 WSR-Flat 5/16 STPL WSR-Wave .37 x .68 x .02 Description 28 29 30 31 32 33 34 35 35A 36 37 37B 38 39 40 41 42 43 43A 44 45 46 47 48 49 50 51 51A Item Parts List 250038 711808 712026 712041 712320 712517 712822 805634 715098CE 830540 740220 762299 762299 833823 760286 760592 762058 809754 740711CE 829014 430120 370074 832973 832974 370031 833827 830292 740477 Part No. 1 1 1 2 2 4 6 1 1 1 1 2 2 1 1 1 1 2 2 1 1 2 2 2 2 1 1 1 Qty. Retainer Clip Cotter Pin-Hair #13 Wire Eye Bolt 1/4 - 20 Blt-Sder 1/4 - 20 x .44 x .37 WSR Nylon .22 x .45 x .04 SCR-MC #8-32 x 1 SS FH SCR-THMS 10 - 24 x .50 STPL Box Cover Decal Dashboard 170CE Twist Loc Receptacle Circuit Breaker 20 amp (115V) Circuit Breaker 9 amp (120V) Grommet .50 x .09 x .75 Dome Plug 2” Wire Formed Hook Knob Oval Tapered Spacer .319 x .375 x .250 Switch Rocker Switch w/Splashguard Flanged Bushing U Channel 170 18" Hubcap Wheel Bracket Clevis Pin 1/4 x 1 3/8 Wheel 1.5 Molded O-Ring 1.25 ID x .187 Cord Assy. 14/3 75’ (115V) Cord Assy. (230V) Description 16 LIMITED WARRANTY Minuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and materials under normal use and service for a period of three years from date of purchase. In addition, Minuteman International, Inc. will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted through and approved by factory authorized repair stations. Minuteman International, Inc. will, at its option, repair or replace without charge, except for transportation costs, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals. This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords, switches, hoses, rubber parts, electrical motor components or adjustments. Parts not manufactured by Minuteman International, Inc. such as engines, batteries, battery chargers, hydraulic pumps, and tires are covered by and subject to the warranties and/ or guarantees of their manufacturers. Please contact Minuteman International, Inc. for procedures in warranty claims against these manufacturers. Special warning to purchaser — Use of replacement filters and/or prefilters not manufactured by Minuteman International, Inc. or its designated licensees, will void all warranties expressed or implied. A potential health hazard exists without exact original equipment replacement. All warranteed items become the sole property of Minuteman International, Inc. or its original manufacturer, whichever the case may be. Minuteman International, Inc. disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose. Minuteman International, Inc. assumes no responsibility for any special, incidental or consequential damages. This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies. Minuteman International, Inc. is not responsible for costs or repairs performed by persons other than those specifically authorized by Minuteman International, Inc. This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to malfunctions of the product. If a difficulty develops with this machine, you should contact the dealer from whom it was purchased. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you. World Headquarters Minuteman International, Inc. 111 South Rohlwing Road Addison, Illinois 60101 Minuteman Canada, Inc. 2210 Drew Road Mississauga, Ontario L5S 1B1 (630) 627-6900 FAX (630) 627-1130 (905) 673-3222 FAX (905) 673-5161 983211 Printed in U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2003:08:06 08:00:50-06:00 Modify Date : 2003:08:06 08:00:50-06:00 Page Count : 19 Creation Date : 2003:08:06 14:00:50Z Mod Date : 2003:08:06 14:00:50Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : kandhamb Metadata Date : 2003:08:06 14:00:50Z Creator : kandhamb Title : 983211, 170 El.p65EXIF Metadata provided by EXIF.tools