Viper Barracuda Cuda2600 Vacuum Parts And Operator Manual

: Sweepscrub Viper-Barracuda-Cuda2600-Vacuum-Parts-And-Operator-Manual viper-barracuda-cuda2600-vacuum-parts-and-operator-manual 1279 file product_file

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

BARRACUDA
DUAL MOTOR VACUUM
www.usviper.com

OWNERS MANUAL
IMPORTANT: READ OWNERS MANUAL CAREFULLY
Please fill out & return your warranty card!

MODEL#

CUDA26

SERIAL#

VIPER NORTH AMERICA
P.O. BOX 104
HAMILTON, MI 49419
(866) 418-4737
(866) 41 - VIPER

VIPER ...exceptional
value
REV.02(08-07)
VA51063

CONGRATULATIONS on your purchase of a Viper product,
and welcome to the V.I.P. family. We appreciate your
business and will do everything in our power to keep you
happy with your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best
protection by one of the most comprehensive warranties in
the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS
Safety Precautions

1

Machine Components

2

Machine Operation

3-4

Machine Maintenance & Storage

4

Troubleshooting

5

Parts Breakdown

6

Parts Lists
Accessories
Wiring Diagram

7-8
9
10

1) Do not operate machine:
- Unless trained and authorized
- Unless you have read and
understand operators manual
- In flammable or explosive areas.
- With damaged or modified cord or
plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- Without bag / filters in place.
- With the use of unapproved
extension cords.

SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
General – This carpet vacuum shall be
grounded while in use to protect the
operator from electric shock. The
machine is provided with a three-contact
grounding type attachment plug to fit the
proper grounding type receptacle. The
green (or green & yellow) conductor in
the cord is the grounding wire. Never
connect this wire to other than the
grounding pin of the attachment plug.

2) Before operating machine:
- Make sure all safety devices are in
place and operate properly.

This machine is for use on a nominal
120-volt circuit and has a grounding plug
that resembles the plug illustrated in
3) When using machine:
figure below. Make sure that the
- Do not run machine over cord.
machine is connected to an outlet having
- Do not pull machine by cord or
the same configuration as the plug. No
plug.
adapter should be used with this machine.
- Do not pull cord around sharp
edges or corners.
- Do not unplug by pulling on the
cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated
surfaces.
- Do not pick up flammable
materials or reactive metals.
- Report machine damage or faulty
operation immediately.
This machine is intended for commercial
- Do not allow children to operate
use. It is constructed for use in an indoor
machine.
environment and is not intended for any
other use. Use only recommended
4) Before leaving or servicing machine:
accessories.
- Turn off machine.
- Unplug power cord from outlet.
All operators shall read, understand and
exercise the following safety precautions:
5) When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or
approved replacement parts.
- Avoid moving parts. Do not wear
loose clothing.

1

MACHINE COMPONENTS
1

3

2

4

5

14

6

13

12
7
8

11

9

10

1) Handle
2) Power cord
3) Door latch
4) Power switch
5) Attachment tool intake & cord wrap
6) Vacuum hose
7) Brush housing
8) Brush height adjustment
9) Rear wheels
10) Exhaust vent
11) Handle height adjustment
12) Brush circuit breaker (bottom side)
13) Brush assembly (bottom side)
14) Rear door

2

3) Occasionally check the bag for
fullness & replace as necessary.
4) If brush stops spinning, there may be
an obstruction in the brush. Unplug
the power cable, raise the brush off
the floor and check for an obstruction.
Check & reset the brush circuit
breaker located on the bottom of the
brush housing.

MACHINE OPERATION
PRIOR TO VACUUMING CARPETS
1) Inspect power cable and extension
cable for damage. Replace cable if
damage is found.
2) Ensure filter bag is properly installed
NOTE: Never operate machine
without filter bag installed. This
could cause damage to the vacuum
motor.
3) Set proper height adjustment for
carpet being cleaned.

USE OF ACCESSORY TOOLS
NOTE: Accessory tools are available as
an option. Kit VA51061 includes:
Dusting brush, crevice tool, upholstery
tool, 8’ vacuum hose, etc.
1) Machine must be in upright position
whenever using attachment tools.
2) Remove vacuum hose on the vacuum
intake port on rear of machine.
3) Connect (optional) 8’vacuum hoses
to intake port & connect desired
accessory tool to end of hose.
4) Turn on vacuum switch and operate
tool using normal vacuuming
procedures.

CARPET VACUUMING
1) Depress foot pedal and lower vacuum
head to floor.
2) Turn on power switch.

3) Operate by using standard vacuuming
procedures.
4) Check bag periodically to see if it is
full. Replace if necessary.
5) To clean under desks or other tight
areas, depress the foot pedal an
additional time to lower the handle
even further.
OPERATING HINTS
1) Overlap cleaning path by approx. 2
inches
2) Work away from power outlet and
power cable in order to avoid damage
to the power cable.

3

5) Check paper bag / filter for fullness.
If it is full, replace with a new one.
6) Check vacuum motor filter and
exhaust filter for debris and clean as
needed.
NOTE: Do not clean filters with water
or a cleaning solution. Clean by tapping
of debris or blowing with air.
7) Inspect brush for strands of carpet
and debris and remove as needed.
8) Inspect brush bristles for wear and
damage. Replace brush as needed.
9) Inspect gaskets and seals for air leaks
and replace as needed.
10) Check vacuum hose for clogs and
holes and replace as needed.
11) Check vacuum motor carbon brushes
every 250 hours. Replace brushes
when they are 3/8” or less in length.
NOTE: Vacuum motor damage
caused by worn brushes is not
covered by warranty.

VACUUM BAG INSTALLATION &
REMOVAL
1) Unlock rear door latch, and allow
door to hinge open.
2) Place paper bag / filter into tank
opening.
3) On paper bag / filter, slide rubber
vacuum collar onto vacuum intake
spout.
4) Close rear door and lock into place.
NOTE: Be sure the bag / filter is
properly placed in bag housing to
ensure proper air flow.
5) To remove bag, simply reverse steps
1-4 above.
6) Do not re-use paper bag / filter.
When full, dispose of it and replace
with a new one.

MACHINE MAINTENANCE

MACHINE STORAGE

To keep the machine performing well
for many years, please follow the
following maintenance procedures.

1) Prior to storing the machine, wrap up
power cord, check paper bag / filter
for fullness and replace if necessary.
2) Clean and / or replace filters.
3) Store machine in upright position in a
dry area, with the brush head off the
floor.

!!! Always confirm that the
machine is unplugged prior to
performing any maintenance or
repairs!!!
1) Unplug machine as soon as you are
done using it.
NOTE: When unplugging machine, do
not pull cord around sharp edges or
corners & do not unplug by pulling on
the cord.
2) Clean outside of machine with a mild
cleaner.
3) Check power cord for any damage. If
any damage is detected, replace the
cord immediately.
4) Check machine for any loose or
missing nuts and bolts and replace as
necessary.

4

BASIC TROUBLESHOOTING
PROBLEM
Machine does not work

CAUSE
Power switch not in "on" position
Power cord not plugged into outlet
Power cord is faulty
Building circuit breaker tripped
Faulty wiring
Faulty on / off switch

Brush does not work

Brush circuit breaker tripped

Poor brush pickup

Incorrect brush height adjustment
Clogged brush
Brush is worn
Loose brush drive belt

Low suction

Vacuum hose clogged
Vacuum hose faulty
Filters clogged
Vacuum bag full

5

SOLUTION
Turn power switch "on"
Plug power cord into outlet
Replace with approved power cord
Reset circuit breaker
Contact Viper Distributor
Contact Viper Distributor
Check brush and belt for obstructions and
remove as needed
Reset circuit breaker
Adjust brush height
Remove debris from brush
Contact Viper Distributor
Inspect belt and replace as needed
Remove vacuum hose and check for
obstructions
Check vacuum hose for loose cuffs or holes
and replace as needed
Remove vacuum filter and exhaust filter and
clean
Check vacuum bag / filter and relplace as
needed

PARTS LIST

6

PARTS LIST
DIA
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

PART
NUMBER
VA51009
VA51025
VA51067
VA51007
GT13022
VA51034
VA51008
VA51022
VV20501
VA13489
VA51023
VF13533
VV13635
VF82028
VF13495
VF13502
VA51065
VA51064
VA51050
VA51073
VV13605
VA51041
VA51027
VA51059
VV20509
VF13520
VF13538
VF48202
VF13666
VF44012
VA51038
VF14214
VA51039
VV67504
GT13057
VA51002
VF99926-1
VA51066
ZD57000
VA51011
VA51019

DESCRIPTION
HANDLE HOUSING
PAPER BAG, DUST, 10.5qt.
CLOTH BAG, DUST(OPTIONAL)
REAR COVER AND BAG HOLDER
NUT, M5, NYLON INSERT
GASKET, ADAPTER
ELBOW ADAPTER, HOSE
PLUG AND CORD HOOK
SCREW, M5x14
NUT, ACORN, M6
HOSE, 2"
WASHER, PLAIN, φ6
SCREW, M5x20
WIRE ROPE, STAY, REAR COVER
SCREW, HEX, M6x16
NUT, M6, NYLON INSERT
FILTER, EXHAUST
HOUSING, EXHAUST FILTER
GASKET, HANDLE HOUSING, 8x13mm, SBR
LATCH PLATE
SCREW, FLAT, M6x16
NYLON WASHER
AXLE
ECCENTRIC BUSHING
SCREW, M5x10
RETAINING RING, EXTERNAL, φ12
WASHER, PLAIN, φ12xφ24x2
WHEEL, 5"
WASHER, PLAIN, φ12
SCREW, M5x12.7
SPRING, LATCH
SCREW, M5x8
SHOULDER BOLT, LATCH
CIRCUIT BREAKER, 2AMP
SCREW, SELF-TAPPING, ST5x10
BUMPER, 26"
RECTIFIER
BLOCK, BRUSH SHAFT, LEFT
MOTOR, BRUSH, 115V
MOUNT PLATE, MOTOR
PULLEY, MOTOR

7

NO
REQ'D
1
1
1
5
1
1
1
20
1
1
10
3
1
5
1
1
1
1
1
2
4
1
2
17
2
2
2
2
2
1
1
1
1
14
1
1
1
1
1
1

PARTS LIST
DIA
NO
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82

PART
NUMBER
VA51021
VF14254
VA51018
VA51035
VF13508
VA51037
VA51036
VA51042
VA51013
VA51043
VA14001
VA51014
VA51004
VA51005
VA51005A
VA51047
VA51003
VA51006
VA51015
VA51017
VA51016
VV20502
VA51048
VA51001
VA51071
VA13476
VA51040
VA51052
VA51012
VV10120
GT13070
VA51032
VA51033
ZD52000A
VA51049
VF82082
VA65001
VA51044
VF83109
VV13650
VA51026
VF91346

DESCRIPTION
DRIVE BELT
SCREW, HOLDING, M5x8
PULLEY, BRUSH
KNOB, ROLLER ADJUST
SCREW, HOLDING, M4x8
SPRING, ROLLER ADJUST
LOCK PIN, ROLLER ADJUST
ROLLER, 1.5"
CLAMP, ROLLER BRACKET
AXLE, ROLLER
RETAINING RING, EXTERNAL, φ10
ROLLER BRACKET
BOTTOM SHOE PLATE, 26"
BRUSH, 26"
BRUSH, ASSEMBLY, 26"
BRACKET, RECTIFIER
BRUSH HOUSING, 26"
SHAFT, BRUSH, 26"
BEARING
STRING GUARD, BRUSH
BLOCK, BRUSH SHAFT, RIGHT
SCREW, FLAT, M5x16
LABEL, "BARRACUDA"
BASE HOUSING, 26"
LATCH, HANDLE
SCREW, M5x40
SHOULDER BOLT, PIVOT
LABEL
TUBE, BASE HOUSING
CLAMP
SCREW, SELF-TAPPING, ST4.8x25
RETAINER RING, VACUUM MOTOR
GASKET, VACUUM MOTOR
VACUUM MOTOR, 115V
FILTER, VACUUM MOTOR
LOGO, "VIPER"
POWER CORD, 14/3C, SJTW, 50FT
STRAIN RELIEF, CORD
CATCH
SCREW, M4x10
PLATE, SWITCH
SWITCH, ROCKER

8

NO
REQ'D
1
1
1
1
1
1
1
2
4
2
4
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
2
1
1
1
4
1
1
1
1
1
1
1
1
6
1
1

ACCESSORIES

ACCESSORIES PARTS LIST(OPTIONAL)
DIA
NO
1
2
3
4
5
6
7

PART
NUMBER
VA51061
VA51060
VA20803
VA20806
VA20807
VA20209
VA20248

DESCRIPTION
KIT TOOLS (OPTIONAL)
HOSE ASSY
DUSTING TOOL
CREVICE TOOL
UPHOLSTERY TOOL
WAND
TUBE

9

NO
REQ'D
1
1
1
1
1
1
2

Black
Green

Black

Green

SJTW 14/3C
Power
Supply
Cord

White

White

Switch

Green

Black

White

10
Green

Green

Black

Circuit
Breaker

Vacuum
Motor

~

~

Brush
Motor

White

+

Red

Rectifier

CUDA26

Black

White

White

Black

Black

Yellow/Green

Black

White

Wiring Diagram



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2008:07:24 10:11:36+08:00
Creator Tool                    : pdfFactory Pro www.pdffactory.com
Modify Date                     : 2008:07:25 08:32:16+08:00
Metadata Date                   : 2008:07:25 08:32:16+08:00
Format                          : application/pdf
Creator                         : Jiang
Producer                        : pdfFactory Pro 3.10 (Windows XP Professional Chinese)
Document ID                     : uuid:81155022-e28e-41de-9e8b-3381a3510543
Instance ID                     : uuid:04176e6b-8b36-4300-bcfc-38dbc6ba1c86
Has XFA                         : No
Page Count                      : 12
Author                          : Jiang

EXIF Metadata provided by EXIF.tools