F Viper R Sl1610se Carpet Extractor Parts And Operator Manual

: Sweepscrub Viper-r-Sl1610Se-Carpet-Extractor-Parts-And-Operator-Manual viper-r-sl1610se-carpet-extractor-parts-and-operator-manual 1291 file product_file

Open the PDF directly: View PDF .
Page Count: 21

Download
Open PDF In Browser	View PDF

Nilfisk Inc.
9435 Winnetka Avenue North
Minneapolis, MN 55445
www.usviper.com

Rev.11(15-12)
VV67149U

TABLE OF CONTENTS
Machine Components
Safety Precautions
Machine Set Up
Machine Operation
Machine Maintenance & Storage
Troubleshooting
Parts Lists
Wiring Diagram

3
4
5
5-6
6-7
8
9-20
21

MACHINE COMPONENTS
2
1

3

11

4
10

5

6

7
9

8
1) Vacuum / pump on/off switch
2) Brush circuit breaker
3) Brush / spray on/off button
4) Drain hose
5) Accessory tool solution hookup
6) Brush raise and lower foot pedal

7) Spray jets
8) Brush assembly
9) Pickup head
10) Solution tank fill port
11) Recovery tank lid

3

1) Do not operate machine:
- Unless trained and authorized
- Unless you have read and
understand operators manual
- In flammable or explosive areas.
- With damaged or modified cord or
plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- Without filters in place.
- With the use of unapproved extension
cords.

SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
General – This carped extraction machine
shall be grounded while in use to protect
the operator from electric shock. The
machine is provided with a three-contact
grounding type attachment plug to fit the
proper grounding type receptacle. The
green (or green & yellow) conductor in the
cord is the grounding wire. Never connect
this wire to other than the grounding pin of
the attachment plug.

2) Before operating machine:
- Make sure all safety devices are in
place and operate properly.

This machine is for use on a nominal 120volt circuit and has a grounding plug that
resembles the plug illustrated in figure
below. Make sure that the machine is
connected to an outlet having the same
configuration as the plug. No adapter
should be used with this machine.

3) When using machine:
- Mix and handle any chemicals
according to manufacturer’s
recommendations
- Do not run machine over cord.
- Do not pull machine by cord or plug.
- Do not pull cord around sharp edges
or corners.
- Do not unplug by pulling on the cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated
surfaces.
- Do not pick up flammable materials
or reactive metals.
- Report machine damage or faulty
operation immediately.

This machine is intended for commercial
use. It is constructed for use in an indoor
environment and is not intended for any
other use. Use only recommended
accessories.

4) Before leaving or servicing machine:
- Turn off machine.
- Unplug power cord from outlet.
5) When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or
approved replacement parts.
- Avoid moving parts. Don’t wear
loose clothing.

All operators shall read, understand and
exercise the following safety precautions:

4

SLIDER EXTRACTOR SETUP

MACHINE OPERATION

!!! Read operators manual thoroughly
prior to operating or servicing this
machine!!!

PRIOR TO EXTRACTING CARPETS
1) Inspect power cable and extension
cable for damage. Replace cable if
damage is found.
2) Vacuum carpet to remove debris prior
to extracting carpet.

Carefully check the shipping carton for
signs of damage. Report any carton
damage to carrier immediately.

CARPET EXTRACTING

Check carton contents to ensure carton is
complete. Contact your Viper distributor if
anything is missing.
Contents:
• Carpet Extractor
• Short “bleeder” vacuum hose
• 50’ extension power cable

1) Turn on vacuum / pump switch.
NOTE: Solution will only spray when
the brush / spray button is pushed.
2) To start cleaning, push the brush /
spray button and begin to pull the
machine backwards.

!!! Read operators manual
thoroughly prior to operating or
servicing this machine!!!
1) Using a hose or bucket, fill tank with a
maximum of 10 gallons of hot water.

NOTE: For best cleaning results, pull
back on the machine at a pace of
approx. 10 feet in 15 seconds.
3) Release brush / spray button at the end
of the path, and continue to pull
machine back for another 12 inches to
pick up excess solution.
4) Tip machine back onto the transport
wheels and push forward to begin next
path.

2) Add distributor recommended cleaning
solution
!!! Do not use flammable liquids or
operate machine in or near
flammable liquids or vapors!!!

OPERATING HINTS
1) Overlap cleaning path by approx. 2
inches
2) Work away from power outlet and
power cable in order to avoid damage
to the power cable.

3) Connect the supplied extension power
cable to the machine. Plug cord into a
grounded wall outlet. (see grounding
instructions)
4) Drop the brush head to the floor with
the foot release pedal on the back of
the machine.

5

3) Continually check for foam buildup in
recovery tank. Use a distributor
recommended foam control solution.
NOTE: Excessive foam buildup will not
activate the float shut-off and may cause
damage to the vacuum motor.
4) Repeat extraction path on heavily
soiled areas.
5) If brush stops spinning, there may be
an obstruction in the brush. Unplug the
power cable, raise the brush off the
floor and check for an obstruction.
Check & reset the brush circuit breaker
located on the control housing.
6) When recover of the dirty solution ends,
or the solution tank is empty, you must
drain the recovery tank. (see TANK
DRAINING)

2) Remove the solution tank filter at the
fill area and place end of “bleeder”
hose into the bottom of the tank.
3) Turn on vacuum / pump switch &
vacuum out the remaining solution.
DRAINING RECOVERY TANK
1) Turn off machine, unplug and remove
power cable.
2) Unhook drain hose off the back of the
machine and remove drain hose
stopper.
3) Drain dirty solution into floor drain.

USE OF ACCESSORY TOOLS
NOTE: Prior to cleaning upholstery, be
sure to read cleaning instructions provided
by the manufacturer.
1) Disconnect black vacuum hose off the
back right side of the machine.
Connect (optional) accessory vacuum
hose to area where the standard
vacuum hose was removed.
2) Connect (optional) accessory solution
hose to brass quick connect coupler
located on the back of the machine.
3) Connect (optional) accessory tool to
solution and vacuum hoses.
4) Turn on vacuum / pump switch.
5) Operate accessory tools as needed.
6) When cleaning is completed, relieve
water pressure from solution lines by
turning off vacuum / pump switch and
then squeeze trigger for 4 seconds.

4) Replace drain hose stopper and
reattach hose to back of machine.
MACHINE MAINTENANCE
To keep the machine performing well
for many years, please follow the
following maintenance procedures.
!!! Always confirm that the machine
is unplugged prior to performing
any maintenance or repairs!!!
DAILY MAINTENANCE
1) When cleaning operation is complete
for the day, drain and rinse the
recovery tank thoroughly with clean
water.
2) Remove remaining solution from
solution tank.
3) Remove float shut-off (ping pong ball
in cage) from recovery tank and clean
with water.

DRAINING TANKS
DRAINING SOLUTION TANK
1) Disconnect vacuum hose from back of
machine and connect the “bleeder”
vacuum hose (included with machine)
to the machine back.

6

system again with 3 gallons of
clean water.
2) Inspect machine for water leaks.
3) Lubricate wheels with a water resistance
lubricant.
4) Check machine for loose or missing
nuts, screw and bolts and replace as
necessary.
MACHINE STORAGE
4) Remove and inspect brass spray jets. If
necessary, clean jets in acetic acid
solution.
NOTE: Do not clean brass jets with a
pointed object, as it will damage the jets.
5) Check brush assembly & remove any
debris or carpet fibers.
6) Check pick up head and remove any
debris or carpet fibers.
7) Check condition of the stainless steel
pickup shoes on the pickup head. The
shoes must contact the floor for the
whole length of the pickup head.
Replace as necessary.
8) Clean machine with a nonabrasive
cleaner.
9) Inspect power cable for any damage.
Replace if necessary.

1) Prior to storing the machine, ensure the
solution and recovery tanks are clean
and empty of any solution.
2) Store machine in upright position in a
dry area, with the brush head off the
floor.
3) Remove recovery tank clear lid to
allow for air circulation.
NOTE: If you are storing the machine in
an area which can freeze, be sure both
tanks and the solution plumbing are empty
of all water and dry!

MONTHLY MAINTENANCE
1) Flush pump & plumbing with an acetic
acid solution to dissolve any chemical
buildup.
Mixing Instructions:
a) Premix 16 oz. or an acetic acid
solution with 2 gallons of water and
pour into solution tank.
b) Turn vacuum / pump switch on
c) Put machine head over floor
drain and operate machine for 50
seconds.
d) Shut machine down and allow
remaining solution to sit in
machine overnight.
e) The following day, spray out
remaining solution and flush

7

BASIC TROUBLESHOOTING
PROBLEM
Machine doesn't
work

Solution pump not
working

CAUSE

SOLUTION

Not plugged in to power source

Plug into a grounded outlet

Faulty power cable

Contact Viper Distributor

Faulty extension power cable

Replace with new extension power cable

Building circuit breaker tripped

Reset circuit breaker

Vacuum / pump switch not on

Turn on switch

Vacuum / pump switch faulty

Contact Viper Distributor

Faulty solenoid

Contact Viper Distributor

Faulty solution pump

Contact Viper Distributor

Pump overheated

Determine cause and allow 30 minutes for
pump to cool

Loose or broken wiring

Contact Viper Distributor

Vacuum motor not
Vacuum / pump switch not on
working

Turn on switch

Vacuum / pump switch faulty

Faulty vacuum motor

Contact Viper Distributor
Check for obstruction and allow 30 minutes
to cool
Contact Viper Distributor

Worn carbon brushes

Contact Viper Distributor

Loose or broken wiring

Contact Viper Distributor

Air leaking around clear recovery lid

Ensure recovery lid is firmly tightened

Clogged float shut-off

Remove float shut-off and clean off debris

Float shut-off is activated

Drain recovery tank

Loose drain hose stopper

Ensure stopper is securely in place

Loose vacuum hose connections

Ensure vacuum hose connections are tight

Defective vacuum hose

Replace vacuum hose

Loose vacuum hose cuffs

Ensure cuffs are secure to the hose

Damaged or loose pickup head shoes

Contact Viper Distributor

Pulling machine too fast

Slow down cleaning operation

Solution tank is empty or low

Fill solution tank

Vacuum / pump switch not on

Turn on switch

Dirty or plugged spray tips

Clean or replace spray tips

Improper spray tip size or spray angle

Contact Viper Distributor

Worn spray tips

Contact Viper Distributor

Faulty solution pump

Contact Viper Distributor

Plugged solution tank filter

Clean or replace filter

Pinched or kinked solution hose

Check for obstructions and kinks and reroute
or replace if needed

Vacuum motor thermal overload tripped

Poor pick up

Uneven or no
solution spray

8

9

PARTS LIST
DIA NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

PART
NUMBER
VV67161
VV67163
VA13477
VV67109
VV67301
VV67302
VV67108
VF81226
VV67706
VV67113-1
VV10113
VV20509
VV13601
VV50712
VV67503
VV67509
VV67504
VF14126
GV40215
VV67111
VV67501
VF99008
VV13511
VF14212
VV67507
VV67116
VV67505
VV13652
VV67508
VV20291
VF13491
VF44203
VV67105
GT13032
VV13607
GT13056
VV80128
VV80115
VV80125A
VV20667
VV60509

DESCRIPTION
CLEAR DOME, FRICTION FIT
GASKET, CLEAR DOME
SELF-TAPPING SCREW,ST4X15
BEND, TUBE
COUPLER
GASKET, COUPLER
ELBOW
COUPLER VAC HOSE
DRAIN HOSE
VAC HOSE
CLAMP, HOSE 2"
SCREW, RHM M5X10 SST
WASHER, LOCK, SST Ø5
CLAMP, CORD
SWITCH
BUTTON, SWITCH
CIRCUIT BREAKER, 2A
SCREW, M5X12, HEX
CORD WRAP
CLAMP, DRAIN HOSE
SWITCH HOUSING
STRAIN RELIEF
WASHER, TEETH, ¢3
SCREW, M3X25
CORD
POWER CORD
BUSHING, CORD, 90°
NUT, LOCK, M3
BRACKET, SWITCH
WASHET, LOCK, ¢4
SCREW, M4X12
SWITCH ASSY
CONNECTOR
WASHER, PLAIN, Ø6XØ16X1.5
WASHER, LOCK, SST Ø6
SCREW, M6X16, PH
BARB, HOSE
ELBOW, STRECT 45°
NUT, COUPLING
WASHER, LOCK, INTERNAL TOOTH

GASKET, SOLUTION, INTAKE

10

NO
REQ'D
1
1
2
2
2
2
1
1
1
1
2
4
2
3
1
1
1
3
1
1
1
1
2
2
1
2
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1

PARTS LIST
DIA NO
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65

PART
NUMBER
VV20276
VV80125
VV10411
VV67101
VF47035A
VV67107
VA13471
VV67102
VF81504
VV67305
VV13664
VF13491
VV67162
VF81403A
VV67708
VF82090
VV67711
VV67118
VF80331
VV67119
VF99010C
VF67514
VF67515
VF20104A

DESCRIPTION
WASHER, PLAIN
COUPLING
STRAINER, LINE
SOLUTION TANK
LOGO
FILTER
SCREW, ST5X10
RECOVERY TANK
FLOAT, SHUT-OFF
BEND
WASHER，PLAIN，¢4¢12X1
SCREW，M4X12，SST
RUBBER HINGE
ELBOW, 90º, BRASS
TUBING
CLAMP(16-20)
ELBOW, 90º, BRASS
LABEL, RIGHT
DECAL, WARNING
LABEL,LEFT
CIRCUIT BREAKER,17A
BUTTON WATER PROOF COVER
BUTTON ORIENTED COVER
PLUG, DRAIN HOSE

NO
REQ'D
1
1
1
1
1
1
2
1
1
1
4
2
1
1
1
1
1
1
1
1
1
1
1
1

12

PARTS LIST

DIA
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

PART
NUMBER
VV80208

VV20274
VV20274A
VV80115
VV80128
VV10114
VV67114
VV67607
VV67604C
VV67608
VF14081
VF13539
VV67601
VV50190
VF81503
ZD55000
GT13032
VV80210
VV67117
VF13521
VF82310
VF14506
VV10113
VV67152
VF13495
VV13607
VF13551
VF82028
VV67104
VF13512
VV60406S
GT13058
GT13056
VF13474A
VV13601
VV13633
VV67140
VV67142
VV67407
VV67400
VV67110
VV67115

DESCRIPTION
COUPLER,QUICK CONNECT
WASHER,PLAIN,Ø13.5XØ32X1.5
WASHER,PLAIN,Ø14XØ32X1.5
ELBOW,STRECT,45°
BARB,HOSE
CLAMP,HOSE 3/8"
HOSE,HIGH PRESSURE
BARB,PUMP
SOLUTION SOLENOID,220V/50HZ
CONNECTOR,THREE-WAY
THIN NUT M12
WASHER,PLAIN,Ø12
MOUNTING FRAME,PUMP
PUMP,220V,100PSI
GASKET,VAC MOTOR
VAC MOTOR,2-STAGE 220V
WASHER,SST,PLAIN,Ø6XØ16X1.5
BEND,NYLON,PUMP
HOSE,SOLUTION
NUT,SST,M6
STUD
NUT,,LOCK,SS,M6
CLAMP,HOSE 2"
EXHAUST HOSE Ø48
BOLT,M6X16,HEX
WASHER,LOCK,Ø6
WASHER,SST,PLAIN,Ø6XØ22X1.5
CABLE
SPACER
SCREW,FH,M5X15,SST
HINGE,SST 4"
SCREW,FH,SST,M5X22
SCREW,SST,PH,M6X16
WASHER,SST,PLAIN,Ø5XØ15X1
WASHER,LOCK,Ø5
NUT,SST,M5
CARPET PICK-UP TOOL
STAINLESS STEEL SHOES
SPRING
MOUNTING BASE ASSY,BRUSH
SHOULDER SCREW
HOSE,SPRAYING

13

NO
REQ'D
1
1
1
1
2
6
1
1
1
1
2
4
1
1
1
1
11
1
1
4
3
6
3
1
2
8
2
1
2
8
2
4
4
8
4
1
1
2
1
1
2
1

PARTS LIST
DIA
NO
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61

PART
NUMBER
VV67120
VA13473
VV67405
VV13635
GT13014
VV67106
VA13478
VV67103A
VF14127
VV67121
VV60113S
VA75004
VF13604
VV13634
VV67200
VV67505
VF143001
GT13022
VF13501

DESCRIPTION
CLAMP
SCREW,RHM,M4X16,SST
STRAINER
SCREW,RHM,M5X20,SST
NUT,NYLON,INSERT,M4
SPACER
SCREW,M6X35,HEX
FOOT STEP
SCREW,RHM,M6X20,SST
ANTISKID PLATE
WASHER,WHEEL,AL
WHEEL,10"
WASHER,Ø5
SCREW,RHM,M5X30,SST
BOTTOM PLATE ASSY
BUSHING,90 ,CORD

°

SCREW,PH,M3X4,SST
NUT,LOCK, M5
NUT,LOCK, M12

14

NO
REQ'D
1
1
1
1
2
4
1
1
2
1
2
2
1
4
1
1
6
4
2

15

PARTS LIST
DIA NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

PART
NUMBER
VV67403-2A
VF44204
VV13601
VV13633
VV13634
VA13475
VV67407
VV20501
VV13662
VV67401
VV80128
VV67423
VV67421
VV67422
ZD57000
VV67433
VV67431-1
GT13054
VF13512A
VV67412
VV67417
VV67414
VV67404
VV67406
VF14024
VF14023
VV67411
VV67413
VV67416
GT13059
VV67415
VV67402
VV67432
VV67424
VV67436
GT13032
VV13607
VF13521
VV67405
VV67408
VV67410

DESCRIPTION
LIFT BAR
RECTIFIER
WASHER,LOCK,SST,Ø5
NUT,SST,M5
SCREW,SST,PH,M5X30
SCREW,PH,SST,M5X25
SPRING
SCREW,PH,SST,M5X14
WASHER,PLAIN,Ø5XØ12X1
MOUTING BASE,BRUSH
BARB,HOSE
INSERT,SPRAYER BODY
SPRAYER BODY
SPRAY TIP
MOTOR,110V
GASKET
BOTTOM PLATE
SCREW,BH,M5X12,SST
SCREW,FH,SST,M5X18
BRUSH
GASKET
FRAME,BRUSH
PLATE
GASKET
BEARING
SEAL
SHAFT,BRUSH
AXLE,PULLEY
SPACER
SCREW,HEX,SOCKET
DRIVEN PULLEY
BELT
DRIVING PULLEY
NOZZLE BODY
MOUNTING BRACKET，MOTOR
WASHER,SST,PLAIN,Ø6XØ16X1.5
WASHER,LOCK,Ø6
NUT,SST,M6
STRAIN RELIEF
POWER CORD
BRUSH ASSEMBLY

16

NO
REQ'D
1
1
5
5
1
2
1
2
6
1
1
2
1
4
1
1
1
10
4
1
2
2
1
1
2
2
1
1
1
4
1
1
1
4
1
4
4
4
1
1
1

17

PARTS LIST
DIA NO
1
2
3
4
5
6
7
8
9
10
11
12
13

PART
NUMBER
VV40328
VV40328-6
VV20071
VV20298
VV60531
VV80159
VV80105
VV80115
VV10933
VV80128
VV10114
VV85317
VV80241

DESCRIPTION
UPHOLSTERY TOOL
WINDOW,HAND TOOL
SCREW,5/16-18X5/8"L,HH
WASHER，LOCK，5/16“L，SST
GASKET
NOZZLE，SPRAY TIP，80º
BUSHING，BRASS
ELBOW，STREET，45 DEGREES
TRIGGER VALVE
BARB，HOSE
CLAMP，HOSE 3/8”
SOLUTION HOSE，3/8”
BARB，HOSE MAIL PLUG

18

NO
REQ'D
1
1
1
1
1
1
1
1
1
1
2
1
1

19

PARTS LIST
DIA NO
1
2
3
4
5
6
7
8
9
10

PART
NUMBER
VV60220
VV67703
VV20652
VV80241
VV10114
VV67704
VV80128
RD80208
VV67703A
VV67704A

DESCRIPTION
CUFF, 1 1/2"
HOSE，VACUUM
TIE，CABLE
HOSE BARB,MAIL PLUG，SST
CLAMP，HOSE，3/8”,SST
HOSE，SOLUTION，16'LONG
HOSE BARB
COUPLER，QUICK CONNECT
VACUUM HOSE ASSEMBLY
SOLUTION HOSE ASSEMBLY

20

NO
REQ'D
2
1
16
1
2
1
1
1
1
1

21



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2010:03:15 16:27:39+08:00
Modify Date                     : 2016:09:28 08:59:43-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29
Metadata Date                   : 2016:09:28 08:59:43-05:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : F:\圣工\VV67\SL1610SE Model (1)
Creator                         : Administrator
Document ID                     : uuid:fece34c3-b089-4951-8a47-2cb5cdb6cfeb
Instance ID                     : uuid:f46a6df2-7cb3-4100-aacd-0d5d462b8c06
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Page Count                      : 21

EXIF Metadata provided by EXIF.tools