D Viper Venom Vn1715 Vn2015 Low Speed Floor Buffer Parts And Operators Manual
2016-10-04
: Sweepscrub Viper-Venom-Vn1715-Vn2015-Low-Speed-Floor-Buffer-Parts-And-Operators-Manual viper-venom-vn1715-vn2015-low-speed-floor-buffer-parts-and-operators-manual 1283 file product_file
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
REV.0 (2014- ) TABLE OF CONTENTS Safety Precautions 3 Machine Operation 4 Machine Maintenance & Storage 4 Parts List Wiring Diagra 5-9 10 SAFETY PRECAUTIONS GROUNDING INSTRUCTIONS - General –This floor – finishing machine shall be grounded while in use to protect the operator from electric shock. The machine is provided with a three –conductor cord and a three contact grounding type attachment plug to fit the proper grounding type receptacle. The green [or green and yellow] conductor in the cord is the grounding wire. Never connect this wire to other than the grounding pin of the attachment plug. - Unless trained and authorized. Unless you have read and understand operators manual. In flammable or explosive areas. With a damaged cord or plug. If not in proper operating condition. In outdoor areas. In standing water. With the use of extension cords. 2] Before operating machine: - Make sure all safety devices are in place and operate properly. This machine is for use on a nominal 120-Volt circuit and has a grounding plug that resembles the plug illustrated in figure below. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine. 3] When using machine: - Do not run machine over cord. - Do not pull machine by cord or plug. - Do not pull cord around sharp edges of corners. - Do not unplug by pulling on the cord. - Do not stretch cord. - Do not handle plug with wet hands. - Keep cord away from heated surfaces. - Report machine damage of faulty operation immediately. 4] Before leaving or servicing machine: - Turn off machine. - Unplug cord from outlet. 5] When servicing machine: - Unplug cord from outlet. - Use manufacturer supplied or approved replacements parts. - This machine is intended for Commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories. All operators shall read, understand and exercise the following safety precautions: 1] Do not operate machine: 3 Operation of Floor Machines * READ OPERATORS MANUAL THOROUGHLY PRIOR TO OPERATING OR SERVICING THIS MACHINE. 10. To stop the machine at any time, simply release the operating trigger(s) and the machine will stop automatically. GENERAL USE MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures. 1. Remove any obstructions or other obstacles in the area which is to be cleaned. 2. Place the handle in the upright position and tilt machine back until handle rests on the floor * Be sure the machine is not plugged into an outlet 3. Attach the pad driver or brush to the machine by placing the clutch plate over the gearbox hub and turning the driver / brush ¼ turn. 4. Place machine back into its upright position. 5. Plug power cord into a grounded outlet. * Never use an extension cord in conjunction with the standard power cord. 6. The handle height may be adjusted by lifting up the compression handle which is located on the right side of the handle tube about 1 foot above floor level. Release the compression handle and adjust handle to safe operating height, then push back down on the compression handle to lock the handle in operating position. 7. To start the machine, press the red safety button on the top of the upper switch housing, and then squeeze either of the operating triggers. (the safety button must be depressed prior to squeezing the operating triggers.) 8. When the machine is in operation, both hands should be placed on the switch housing (upper handle). 9. During operation, to make the machine go right, gently raise the handle. To make the machine go left, gently lower the handle. * Always confirm that the machine is unplugged prior to performing any maintenance or repairs. 1. Unplug machine as soon as you are done using it. 2. Tilt machine back and remove pad driver or brush. * Never store a low speed machine with the pad driver or brush mounted to the machine. 3. Clean the outside of the machine with a mild cleaner. 4. Check power cord for any damage. If damage is detected, replace power cord immediately. 5. Lubricate wheels with a water resistant lubricant once a month. 6. Check machine for loose or missing nuts and bolts, and replace as necessary. 7. If the machine is used in a dusty environment, you may remove the motor cover and blow the motor clean with compressed air. This will ensure proper ventilation, and allow the motor to run cooler. STORAGE 1. Unplug machine from power source and wrap cord on handle. 2. Tilt machine back and remove pad driver or brush. 3. Store machine in upright position and in a dry area. 4 5 HANDLE GROUP FOR VN1715 & VN2015 DIA NO PART NUMBER 1 VF30016 HANDLE RELEASE 1 2 VF30015 BOLT, HANDLE RELEASE 1 3 VF30018 WASHER, PLAIN 2 4 VF13503 NUT, LOCK, M8 X 5.7 1 DESCRIPTION NO REQ'D 5 VF30017 SCREW 1 6 VF30014 COVER, HOOK 1 7 VF45125 CORD, HANDLE 1 8 AS41901 PLUG PROTECTOR, SMALL MALE 1 9 VF50120A GROMMET 1 10 VF13504 NUT, LOCK, M10 1 11 VF30027 WASHER, PLAIN 1 12 VF14114 SCREW, M8 X 55 1 13 VF30013 HOOK, CORD 1 14 VF13493 SCREW, M6 X 10 1 15 AS112205 TUBE 1 16 VF44018 LEVER,SOLUTION 1 17 VV13667 SCREW, M4 X 8 2 18 VF48306 PIN 3 19 VF44016 LEVER, LEFT, SWITCH 1 20 VF45119 CORD, POWER SUPPLY 1 21 AS22009 STRAIN RELIEF, CORD 1 22 VF30108 GASKET, HANDLE, SOLUTION 1 23 VF14223 SCREW, M6 X 25 2 SCREW, M6 X 45 2 24 VF14218 25 VF13528 26 VF30102 REAR COVER, SWITCH HOUSING 1 27 VF99010C BREAKER, CIRCUIT, 17A 1 28 VF30109 COVER 1 29 GT13013 NUT, M4 3 WASHER, TOOTH, M6 2 30 VF48309 CLAMP BLOCK 1 31 VF44017 LEVER, RIGHT, SWITCH 1 32 VF44203 SWITCH ASSEMBLY 1 33 VF14212 SCREW, M3 X 25 2 34 VF13527 WASHER, TOOTH, M4 1 35 VF13526 SCREW, M4 X 30 1 36 VF46705 SAFETY BUTTON 1 37 GV40218 SPRING, SAFETY BUTTON 1 38 VF48310 HANDLE GRIP 2 39 VF30101 FRONT COVER, SWITCH HOUSING 1 40 VF47035A "VIPER" LOGO 1 41 VF13604 42 VF14222 WASHER, TOOTH, M5 SCREW, M5 X 12 6 4 4 7 BASE GROUP FOR VN1715 & VN2015 DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 GT13080 SCREW, M6 X 30 4 2 VF30011 CLAMP BLOCK, HANDLE 2 3 VF30026 AXLE 1 4 VF30020 BRACKET, LEFT HANDLE 1 5 VV20274 WASHER, PLAIN, M13 4 6 GV40235 CLAMP BLOCK, AXLE 2 7 VV13621 SCREW, SELF-TAPPING, ST, M5 X 20 4 8 VF13474A WASHER, PLAIN, M5 4 9 VF13613 SCREW, M5 X 20 2 10 VA13474 SCREW, M5 X 16 5 11 VF13524 WASHER, PLAIN,M8 4 12 VF13519 WASHER, LOCK, M8 4 13 VF14114 SCREW, M8 X 55 4 14 MF-VF002-4A SCREW, SELF-TAPPING, 1/4"-1" 6 15 MF-VF002-2 CLUTCH PLATE 1 MF-VF022 VN2015 - PAD HOLDER, 19-INCH 1 MF-VF021 VN1715 - PAD HOLDER, 16-INCH 1 17 VF999802B GEAR BOX 1 18 VF99021 COUPLER 1 19 MT01102 SLEEVE 1 VF30004 VN2015 - BUMPER, 20-INCH 1 VF30005 VN1715 - BUMPER, 17-INCH 1 21 VF999821A BEARING,6002 LLU 1 22 VV13601 WASHER, LOCK, M5 6 23 VV13636 SCREW, M5 X 30 6 VF30006 VN2015 - FRAME, 20-INCH 1 16 20 VF30006A SHROUD & BUMPER ASSY, 20-INCH 1 VF30007 VN1715 - FRAME 17-INCH 1 VF30007A SHROUD & BUMPER ASSY, 17-INCH 1 25 YLQ19200B ROTOR WITH FAN ASSEMBLY 1 26 YCQ10501 BEARING,6203 RZ 1 27 YCQ12301 CENTRIFUGAL SWITCH 1 28 VF14549 SCREW, M4 X 10 2 24 29 VF30008 ALUMINIUM BASE, MOTOR 1 30 YCQ12302 STATIONARY SWITCH 1 31 VF999854 RUNNING CAPACITOR, 50μF / 370V 1 32 VF40152 HOSE BARB 1 33 YLQ14601 MOUNTING FRAME (SMALL), CAPACITOR 1 34 VF30019 BRACKET, HANDLE, RIGHT 1 35 VF13520 WASHER, LOCK 2 8 BASE GROUP FOR VN1715 & VN2015 DIA NO PART NUMBER DESCRIPTION NO REQ'D 36 VF50119 WASHER, PLAIN, M12 2 37 VF14214 SCREW, M5 X 8 4 38 VF48202 WHEEL, 5" 2 39 VF40994 LABEL, READ MANUAL 1 40 VF44012 SCREW, M6 X 12.7 2 41 VF13666 WASHER, M6 2 42 VF13604 WASHER, LOCK, EXTERNAL TOOTH 4 43 YCQ10615 MOUNTING FRAME (BIG), CAPACITOR 1 44 AS41902 PLUG PROTECTOR, LARGE FEMALE 1 45 YCQ10414 CLEAR COVER 4 46 YCQ10416 CAPACITOR WRAP 2 47 VF999805 START CAPACITOR (BIG), 380-400F / 150V 1 48 YLQ17507 BOLT ASSEMBLY 4 49 SEE #17 & #50 50 VF999787 MOTOR, 110V, 1.5HP 1 51 VF44003 LABEL, MOTOR 1 52 VF41079 LABEL, VIPER 1 53 VF14222 SCREW, M5 X 12 3 54 VF30001 TOP COVER, MOTOR 1 55 VF30002 CLUTCH PLATE 1 56 VF47023 BUMPER 1 9 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Administrator Create Date : 2009:06:10 15:58:47+08:00 Modify Date : 2016:09:22 10:33:37-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29 Metadata Date : 2016:09:22 10:33:37-05:00 Creator Tool : Adobe Acrobat 8.0 Combine Files Format : application/pdf Title : D:\breakdown\USVIPER\TOTAL P1 Model (1) Creator : Administrator Document ID : uuid:1f14ca3a-6033-4a38-8240-db5121a0db2a Instance ID : uuid:69704090-40c3-435b-b1e1-fd39bee88653 Producer : Acrobat Distiller 8.0.0 (Windows) Page Count : 10EXIF Metadata provided by EXIF.tools