D Viper Venom Vn1715 Vn2015 Low Speed Floor Buffer Parts And Operators Manual
2016-10-04
: Sweepscrub Viper-Venom-Vn1715-Vn2015-Low-Speed-Floor-Buffer-Parts-And-Operators-Manual viper-venom-vn1715-vn2015-low-speed-floor-buffer-parts-and-operators-manual 1283 file product_file
Open the PDF directly: View PDF 
.
Page Count: 10
REV.0 (2014- )
TABLE OF CONTENTS
Safety Precautions 3
Machine Operation 4
Machine Maintenance & Storage 4
Parts List 5 - 9
Wiring Diagra
10
SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
General –This floor – finishing machine shall be
grounded while in use to protect the operator
from electric shock. The machine is provided
with a three –conductor cord and a three contact
grounding type attachment plug to fit the proper
grounding type receptacle. The green [or green
and yellow] conductor in the cord is the
grounding wire. Never connect this wire to other
than the grounding pin of the attachment plug.
This machine is for use on a nominal 120-Volt
circuit and has a grounding plug that resembles
the plug illustrated in figure below. Make sure
that the machine is connected to an outlet
having the same configuration as the plug. No
adapter should be used with this machine.
This machine is intended for Commercial use. It
is constructed for use in an indoor environment
and is not intended for any other use. Use only
recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1] Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand
operators manual.
-In flammable or explosive areas.
-With a damaged cord or plug.
-If not in proper operating condition.
-In outdoor areas.
-In standing water.
-With the use of extension cords.
2] Before operating machine:
-Make sure all safety devices are in place
and operate properly.
3] When using machine:
-Do not run machine over cord.
-Do not pull machine by cord or plug.
-Do not pull cord around sharp edges of
corners.
-Do not unplug by pulling on the cord.
-Do not stretch cord.
-Do not handle plug with wet hands.
-Keep cord away from heated surfaces.
-Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:
-Turn off machine.
-Unplug cord from outlet.
5] When servicing machine:
-Unplug cord from outlet.
-Use manufacturer supplied or approved
replacements parts.
-
3
Operation of Floor Machines
* READ OPERATORS MANUAL
THOROUGHLY PRIOR TO OPERATING OR
SERVICING THIS MACHINE.
GENERAL USE
1. Remove any obstructions or other
obstacles in the area which is to be
cleaned.
2. Placethehandleintheuprightposition
and tilt machine back until handle rests
on the floor
* Be sure the machine is not plugged into
an outlet
3. Attach the pad driver or brush to the
machine by placing the clutch plate over
thegearboxhubandturningthedriver
/brush¼turn.
4. Place machine back into its upright
position.
5. Plug power cord into a grounded outlet.
* Never use an extension cord in
conjunction with the standard power cord.
6. The handle height may be adjusted by
lifting up the compression handle which
is located on the right side of the handle
tube about 1 foot above floor level.
Release the compression handle and
adjust handle to safe operating height,
then push back down on the
compression handle to lock the handle in
operating position.
7. To start the machine, press the red
safety button on the top of the upper
switch housing, and then squeeze either
of the operating triggers. (the safety
button must be depressed prior to
squeezing the operating triggers.)
8. When the machine is in operation, both
handsshouldbeplacedontheswitch
housing (upper handle).
9. During operation, to make the machine
go right, gently raise the handle. To
make the machine go left, gently lower
the handle.
10. To stop the machine at any time,
simply release the operating trigger(s)
and the machine will stop automatically.
MAINTENANCE
To keep the machine performing well for
many years, please follow the following
maintenance procedures.
* Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1. Unplugmachineassoonasyouare
done using it.
2. Tilt machine back and remove pad driver
or brush.
* Never store a low speed machine with
the pad driver or brush mounted to the
machine.
3. Clean the outside of the machine with a
mild cleaner.
4. Check power cord for any damage. If
damage is detected, replace power cord
immediately.
5. Lubricate wheels with a water resistant
lubricant once a month.
6. Check machine for loose or missing nuts
and bolts, and replace as necessary.
7. If the machine is used in a dusty
environment, you may remove the motor
cover and blow the motor clean with
compressed air. This will ensure proper
ventilation, and allow the motor to run
cooler.
STORAGE
1. Unplug machine from power source and
wrap cord on handle.
2. Tilt machine back and remove pad driver
or brush.
3. Store machine in upright position and in
adryarea.
4
5
DIA
NO
PART
NUMBER
NO
REQ'D
1VF30016 HANDLE RELEASE 1
2VF30015 BOLT, HANDLE RELEASE 1
3VF30018 WASHER, PLAIN 2
4VF13503 NUT, LOCK, M8 X 5.7 1
5VF30017 SCREW 1
6VF30014 COVER, HOOK 1
7VF45125 CORD, HANDLE 1
8AS41901 PLUG PROTECTOR, SMALL MALE 1
9VF50120A GROMMET 1
10 VF13504 NUT, LOCK, M10 1
11 VF30027 WASHER, PLAIN 1
12 VF14114 SCREW, M8 X 55 1
13 VF30013 HOOK, CORD 1
14 VF13493 SCREW, M6 X 10 1
15 AS112205 TUBE 1
16 VF44018 LEVER,SOLUTION 1
17 VV13667 SCREW, M4 X 8 2
18 VF48306 PIN 3
19 VF44016 LEVER, LEFT, SWITCH 1
20 VF45119 CORD, POWER SUPPLY 1
21 AS22009 STRAIN RELIEF, CORD 1
22 VF30108 GASKET, HANDLE, SOLUTION 1
23 VF14223 SCREW, M6 X 25 2
24 VF14218 SCREW, M6 X 45 2
25 VF13528 WASHER, TOOTH, M6 2
26 VF30102 REAR COVER, SWITCH HOUSING 1
27 VF99010C BREAKER, CIRCUIT, 17A 1
28 VF30109 COVER 1
29 GT13013 NUT, M4 3
30 VF48309 CLAMP BLOCK 1
31 VF44017 LEVER, RIGHT, SWITCH 1
32 VF44203 SWITCH ASSEMBLY 1
33 VF14212 SCREW, M3 X 25 2
34 VF13527 WASHER, TOOTH, M4 1
35 VF13526 SCREW, M4 X 30 1
36 VF46705 SAFETY BUTTON 1
37 GV40218 SPRING, SAFETY BUTTON 1
38 VF48310 HANDLE GRIP 2
39 VF30101 FRONT COVER, SWITCH HOUSING 1
40 VF47035A "VIPER" LOGO 1
41 VF13604 WASHER, TOOTH, M5 4
42 VF14222 SCREW, M5 X 12 4
HANDLE GROUP FOR VN1715 & VN2015
DESCRIPTION
6
7
DIA
NO
PART
NUMBER
NO
REQ'D
1GT13080 4
2VF30011 2
3VF30026 1
4VF30020 1
5VV20274 4
6GV40235 2
7VV13621 4
8VF13474A 4
9VF13613 2
10 VA13474 5
11 VF13524 4
12 VF13519 4
13 VF14114 4
14 MF-VF002-4A 6
15 MF-VF002-2 CLUTCH PLATE 1
MF-VF022 1
MF-VF021 1
17 VF999802B 1
18 VF99021 1
19 MT01102 1
VF30004 1
VF30005 1
21 VF999821A 1
22 VV13601 6
23 VV13636 SCREW, M5 X 30 6
VF30006 1
VF30006A SHROUD & BUMPER ASSY, 20-INCH 1
VF30007 VN1715 - FRAME 17-INCH 1
VF30007A SHROUD & BUMPER ASSY, 17-INCH 1
25 YLQ19200B 1
26 YCQ10501 1
27 YCQ12301 1
28 VF14549 2
29 VF30008 ALUMINIUM BASE, MOTOR 1
30 YCQ12302 STATIONARY SWITCH 1
31 VF999854 RUNNING CAPACITOR, 50μF / 370V 1
32 VF40152 HOSE BARB 1
33 YLQ14601 MOUNTING FRAME (SMALL), CAPACITOR 1
34 VF30019 BRACKET, HANDLE, RIGHT 1
35 VF13520 WASHER, LOCK 2
DESCRIPTION
SCREW, M6 X 30
CLAMP BLOCK, HANDLE
AXLE
20 VN2015 - BUMPER, 20-INCH
16 VN2015 - PAD HOLDER, 19-INCH
COUPLER
WASHER, LOCK, M5
WASHER, PLAIN, M5
SCREW, M5 X 20
SCREW, M5 X 16
WASHER, PLAIN,M8
BRACKET, LEFT HANDLE
WASHER, PLAIN, M13
CLAMP BLOCK, AXLE
SCREW, SELF-TAPPING, ST, M5 X 20
SCREW, M4 X 10
ROTOR WITH FAN ASSEMBLY
VN2015 - FRAME, 20-INCH
WASHER, LOCK, M8
SCREW, M8 X 55
VN1715 - PAD HOLDER, 16-INCH
GEAR BOX
SLEEVE
VN1715 - BUMPER, 17-INCH
BEARING,6002 LLU
BASE GROUP FOR VN1715 & VN2015
24
SCREW, SELF-TAPPING, 1/4"-1"
BEARING,6203 RZ
CENTRIFUGAL SWITCH
8
DIA
NO
PART
NUMBER
NO
REQ'D
36 VF50119 WASHER, PLAIN, M12 2
37 VF14214 SCREW, M5 X 8 4
38 VF48202 WHEEL, 5" 2
39 VF40994 LABEL, READ MANUAL 1
40 VF44012 SCREW, M6 X 12.7 2
41 VF13666 WASHER, M6 2
42 VF13604 WASHER, LOCK, EXTERNAL TOOTH 4
43 YCQ10615 MOUNTING FRAME (BIG), CAPACITOR 1
44 AS41902 PLUG PROTECTOR, LARGE FEMALE 1
45 YCQ10414 CLEAR COVER 4
46 YCQ10416 CAPACITOR WRAP 2
47 VF999805 1
48 YLQ17507 4
49
50 VF999787 MOTOR, 110V, 1.5HP 1
51 VF44003 LABEL, MOTOR 1
52 VF41079 LABEL, VIPER 1
53 VF14222 SCREW, M5 X 12 3
54 VF30001 TOP COVER, MOTOR 1
55 VF30002 CLUTCH PLATE 1
56 VF47023 1
BASE GROUP FOR VN1715 & VN2015
BUMPER
BOLT ASSEMBLY
SEE #17 & #50
START CAPACITOR (BIG), 380-400F / 150V
DESCRIPTION
9
10
