Swisher LS728C, LS10528C Microsoft 11815 User Manual To The 78e8e8eb D163 4683 A214 Bd659bd23cda

User Manual: Swisher LS728C, LS10528C to the manual

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

swisherinc.com

OWNER’S
MANUAL

MODEL NO.
LS728C
LS10528C

IMPORTANT
Read and follow all Safety
Precautions and Instructions
before operating this
equipment.

Rev.

LOG
SPLITTER
Safety
Assembly
Operation
Service and Adjustment
Repair Parts

1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
FAX 660-747-8650

PHONE 660-747-8183

Manufacturing quality lawn care equipment since 1945
11815

Made In The

USA

LIMITED WARRANTY
The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in
materials and workmanship for a period of two (2) year from the date of purchase by the original consumer
purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or
workmanship. This warranty is subject to the following limitations and exclusions:
1)

Engine Warranty

Commercial Use

Limitation

Exclusions

All engines utilized on our products have a separate warranty extended
to them by the individual engine manufacturer. Any engine service
difficulty is the responsibility of the engine manufacturer and in no
way is Swisher Mower Co., Inc. or its agents responsible for the engine
warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800233-3723. The Tecumseh Engine Service Hot-Line is 1-800-558-5402.
The Honda Engine Service Hot-Line is 1-800-426-7701.
The warranty period for any product used for commercial or rental is
limited to ninety (90) days from the date of original purchase.
This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher Mower Co., Inc., that has been subject to alteration,
misuse, abuse, improper assembly or installation, shipping damage, or
to normal wear of product.
Excluded from this warranty are normal wear, normal adjustments, and
normal maintenance. The pump, valve, and cylinder each carry separate
manufacture’s warranties. The valve and cylinder both carry a one (1) year
limited warranty. The pump carries a two (2) year limited warranty.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer.
All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or
repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this
warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,
and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any
warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS
STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of
consequential damages or limitations on how long an implied warranty may last, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights,
which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

TABLE OF CONTENTS
WARRANTY………………....….2
SAFETY..……………………….3-4
TOWING..….……..……………..5
OPERATION……………………6-8

MAINTENANCE.…………………….8-9
DECALS…..………….……………….10
PARTS BREAKDOWN…………….11-18
SPECIFICATIONS..…………………23

SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this manual.
When you see this symbol, carefully read the message that follows and be
alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw objects.
Failure to observe the following safety instructions could result in serious injury or death.
WARNING: The engine exhaust from this product contains chemicals known to the state of
California to cause cancer, birth defects or other reproductive harm.
DANGER: Your log splitter was built to be operated according to the rules for safe operation in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. If you violate any of these rules, you may cause serious
injury to yourself or others.
•

Read the manual. Learn to operate this equipment in a safe manner.

•

Do not under any circumstances alter this log splitter. This equipment was designed and
engineered in accordance with operating instructions. Altering this equipment, or using
this equipment in such a way as to circumvent its design capabilities and capacities, could
result in serious injury or fatality and WILL VOID THE WARRANTY.

•

Allow only responsible adults who have read this manual to operate this machine. Never
allow children to operate this machine.

•

Never use splitter for any other purpose than splitting wood. Any other use can result in
injury. Your splitter is a precision piece of power equipment, not a toy. Therefore,
exercise extreme caution at all times.

•

Only a single operator is to load and operate the log splitter. Keep all others, including
pets and children, a minimum of 20 feet away from your work area. More accidents
occur when more than one person operates the log splitter than any other time.

•

Always disconnect the spark plug wire and place the wire where it cannot contact the
spark plug, to prevent accidental starting the engine when setting up, transporting,
adjusting or repairing.

•

Always wear protective gear such as safety goggles, protective hearing device, steel-toed
shoes, and tight-fitting gloves without drawstrings or loose cuffs.

•

Never wear loose clothing or jewelry that can be caught by moving parts of the splitter
and pull you into it. Keep hair away from moving parts.

•

Familiarize yourself with all of the controls in a safe environment before starting to work
with this machine.

Fluid escaping from a very small hole can be almost invisible. Do not check for leaks with your
hand. Escaping fluid under pressure can have sufficient force to penetrate skin, causing serious
personal injury. Leaks can be located by passing a piece of cardboard or wood over the suspected
leak and looking for discoloration. IF injured by escaping fluid, see a doctor at once. Serious
infection or reaction can develop if proper medical treatment is not administered
immediately.

•

Split only one log at a time. Never attempt to split two logs on top of each other.

•

Do not straddle or reach across the splitting area while operating the splitter.

•

Do not step over splitter when the engine is running. You may trip or accidentally
activate the splitting wedge. Walk around to get to the other side.

•

Never place hands or feet between log and splitting wedge or between log and ram during
forward or reverse stroke.

•

Never attempt to load splitter while splitting wedge is in motion. When loading log
splitter, place hands on the sides of the log, not the ends.

•

Only use your hands to operate the control lever. Never use foot, knee, rope or any
extension device.

•

Always keep fingers clear of splits that open in log during splitter operation.

•

When splitter is in the return mode, keep hands off the machine.

•

Only operate splitter on level ground, not on the side of a hill. It could tip or rolling logs,
poor footing, etc. could cause an accident.

•

Never operate or allow someone to operate this equipment while under the influence of
alcohol or drugs.

•

Always block the wheels to prevent movement while using splitter.

•

Never operate your splitter on wet, muddy, or icy surfaces. Safe footing is essential in
preventing accidents.

•

Never operate your splitter while it is attached to the tow vehicle.

•

Never make adjustments or repairs with the engine running.

•

Never attempt to split woods across the grain. Some types of wood may burst or fly out
of your splitter and result in injury.

•

Both ends of the log should be cut as squarely as possible to prevent the log from sliding
out of the splitter during operation. Log length should be kept to 24” or less.

TOWING SAFETY
•

Do not allow persons to ride on splitter. Do not carry any cargo or wood on your
splitter. It may fall off and endanger vehicles that are following you.

•

Be sure jack stand is in the travel position and coupling secure. This must also be
retracted so not to interfere while towing. Retract kickstand by removing pin,
rotating up, and replacing pin.

•

Never exceed 45 MPH while towing your splitter. Be extra cautious when
traveling over rough terrain, especially over railroad tracks.

•

Always be careful while backing your splitter. You could jackknife your log
splitter if not careful.

•

Before using splitter, disconnect it from tow vehicle. A log could easily be
pushed forward into the vehicle.

•

See tire and wheel specifications for PSI while towing.

•

Be aware of the extra length of splitter while turning, parking, crossing
intersections, and in all driving situations.

•

OPERATION INSTRUCTIONS
POSI-LOCK COUPLER
ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED
POSITION WITH BALL IN COUPLER. TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT
COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE
RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.
TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL
WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE
BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.
AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK
TIGHTNESS BEFORE TOWING. BE SURE COUPLER HANDLE IS IN LOCKED POSITION.
WARNING:
NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE
CORRECT BALL SIZE, MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER. LOCK
COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR DAMAGES AND
REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.

OPERATION
Intended use: This log splitter is intended and designed to only split wood. NEVER use
for any other purposes. Doing so can cause injury or VOID THE WARRANTY.
ASSEMBLY INSTRUCTIONS
This log splitter has been partially assembled at the factory. Refer to the drawings and part
lists should it become necessary to disassemble the unit for repair or replacement of parts.
Inspect all components for damage.
WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or
mechanical handling equipment should be used.
IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After
assembly, see separate Engine Manual for proper fuel and oil recommendations.
1. General Assembly: Remove top, sides and ends of crate. Place crate panels aside
to avoid puncturing tires. Remove tongue assembly from top.
2. Carefully set the beam pre-assembly aside.
3. Attach tongue to tank/mount plates using two bolts and nuts. Be certain hardware
is secure. (See Assembly Figure 1)
4. Remove tank/engine assembly from base of crate and discard banding.
5. Fender Assembly: Remove fenders from box. Mount to fender brackets with 5/16
hardware provided. Make sure fender clears wheel.
6. The cylinder is tied to the base. Remove ties and slide cylinder/wedge forward
aligning clevis at cylinder end to beam. Insert pin and retaining clips, check
component to assure proper assembly. Stand beam pre-assembly vertical and
secure in position. Roll tank/engine assembly into place, aligning pivot holes. Bolt
with provided hardware. Note: Do not over tighten; this is the vertical/horizontal
pivot point.

Tank/Mount Plates

Assembly Figure 1

7. Pivot beam assembly into the horizontal position and lock with pin provided.
8. Hose Assembly: Locate the Pressure Hose, noted by the pipe fittings, and attach it
to the lower fitting on the valve. The remaining hose attaches to the top fitting of
the valve. Secure with provided hose clamp.
9. Check both the horizontal and vertical positions for any “kinks” in the hoses. Note:
Always make sure beam is locked securely into place.
See OPERATING POSITIONS for Horizontal to Vertical Splitting

OPERATION
FILLING THE HYDRAULIC RESERVOIR
Fill the hydraulic reservoir with at least five gallons of General Purpose Hydraulic fluid or
Automatic Transmission fluid. After the hydraulic reservoir and the engine crankcase are filled
correctly with their respective oils, start the engine. Remember to set the throttle and turn on the
fuel shut-off valve. The hydraulic pump should prime itself. With the engine running, move the
hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air.
When the cylinder is fully extended, retract it. Repeat this procedure several times. (An erratic
movement of the cylinder indicates that there is air in the system). You may have to add more
fluid and repeat this procedure. Once the cylinder has a smooth and constant speed indicating
that all the air has been expelled, more oil should then be added to bring the fluid level up to
approximately 3” below the fill hole. Standard models require approx. 4.5 gallons of hydraulic
fluid.
NOTE: If the tank is overfilled, it will tend to expel oil from the breather cap when the cylinder
is retracted.
START UP
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE
ENGINE AND HYDRAULIC RESERVOIR.
See separate Engine Manual for fuel and oil recommendations. Your log splitter has come
equipped with a fuel shut-off valve for towing purposes.
Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has
been used. The engine will only start when the throttle lever and fuel shut-off valve are turned
to their ON positions.
COLD WEATHER START UP
The Cold Weather Clutch enables the engine to be started without having to pull through cold,
thickened hydraulic fluid. Simply pull the handle out and slide into locked position. Start
engine, let it warm up, and release Cold Weather Clutch. After starting, assure that the lever has
reengaged.
TOWING
This unit should not be towed on any street, highway, or public road without checking the
existing federal, local, and state laws. Any licensing or modifications such as taillights, etc.,
need to comply with existing federal, local, or state vehicle requirements is the sole
responsibility of the purchaser. Obey all regulations when towing on public roads and
highways. See also TOWING SAFETY.
Be sure you are using the correct ball hitch size for the hitch coupler on the log splitter (2” ball).
Be sure safety chains are properly connected. Leave enough slack in chains for turning. See
TOWING SAFETY to read warnings about coupling.
Make sure beam attachment is locked in the horizontal position. NEVER tow splitter in the
vertical position.
Turn the fuel shut-off valve OFF to prevent flooding of the engine while traveling.
TOWING AT NIGHT
The requirements for taillights are based on States regulations. Some states allow towing at
night as long as the towed equipment does not visibly impair the tow vehicle taillights. This is
based on a state, to state requirements. The customer is responsible for meeting the states
requirements. A Taillight Kit Accessory (Part No. 7420)is available and recommended for night
driving.

If a “Statement of Origin” is required in your state, see your local dealer to receive one.

OPERATION
1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank
should always be on the lower side of the log splitter.
2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate
and up against the beam.
3. Depress the valve lever so that the cylinder will drive the wedge into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not completely split after the cylinder
has reached the end of its extension, retract the cylinder. NOTE:

Leaving the valve in the “actuate” position at the end of the stroke may damage the pump.
OPERATING POSITIONS
WARNING: THE LOG SPLITTER BEAM IS HEAVY AND CAN PINCH HANDS/FINGERS IF
CARE IS NOT TAKEN.
STANDARD HORIZONTAL TO VERTICAL
The Standard Splitter has 2 operating positions: Horizontal, Vertical.
Remove pin from below beam. Do not remove bolt and nut. Rotate beam into vertical position and pin
so beam cannot fall into horizontal position.
DO NOT TOW IN VERTICAL POSITION!

IMPORTANT: When operating splitter in wooded areas, obtain a spark arrestor for the exhaust system.
See your local engine dealer.
When preparing logs, cut ends as square as possible. The maximum length of any logs should be only
24”.
MAINTENANCE & STORAGE
WARNING: Disconnect spark plug before performing any maintenance or making adjustments.
RESERVOIR FLUID
Check the hydraulic fluid level in the reservoir tank before each use. Operating without an adequate oil
supply will cause severe damage to the pump. Change the hydraulic fluid in the reservoir per
manufacturers recommendations.
Be aware of the environment when disposing of used petroleum products. Please dispose of used
hydraulic fluid, engine oil and any by products from the maintenance of your log splitter at
approved recycling centers.
Should it become necessary to loosen or remove any hydraulic fitting or line, be sure to remove all
pressure by shutting off the engine and moving the control handle back and forth several times.
NEVER remove the cap from the hydraulic tank or reservoir while your unit is running. Hot oil
under pressure will cause injury.
Always store gasoline in an approved, tightly sealed container. Store container in a dry, cool place. Keep
fuel away from gas appliances where fumes could contact open flame, pilot lights or sparks.

Do not operate your splitter in poor mechanical condition or when needing repair. Repair and
replace worn or broken parts immediately.
Periodically tighten nuts, bolts, and hydraulic fittings.
The hydraulic system of your log splitter requires careful inspection, along with the mechanical
parts. Be sure to replace frayed, kinked, or otherwise damaged hydraulic components.
The pressure relief valve on the splitter is preset at the factory. Do not adjust valve. Only a
qualified service technician should perform this adjustment.
If the wedge becomes dull or nicked, it can be removed and sharpened. The wedge is heavy and
may still have sharp edges, wear gloves while handling the wedge.
REPAIR PARTS
Your Swisher Log Splitter has been produced with components designed specifically to this
machine. Although standard springs, hardware, etc. may look similar to parts used on other
machinery, they may in some cases be made of a different construction and/or materials.

SAFETY DECALS
Replace decals immediately if damaged.

OD07 – COLD WEATHER DECAL

OD16 – FUEL SHUT OFF DECAL

OD12 – HYDRAULIC FILL PLUG
DECAL

OD08 – OPERATOR INSTRUCTION
DECAL

OD09 – DANGER/POSITION LOCK
DECAL

SEE DETAIL

1
3

5
13

25
21

FENDERS & FENDER
BRACKETS SOLD
SEPERATELY

15
6

14 20
B

10
27

6
7

16
22

24
22

SEE DETAIL

23
5

25
31

43
42

44
30
32

45
46

37 41
42
38
47
48
49
39

54
18

18
28
51

ASSEMBLY DETAIL
LS728C, LS10528C MODELS
NOT ALL PARTS ARE ON ALL MODELS
11

SERVICE PARTS
Please have Model and Serial Numbers ready when ordering parts.
Color cannot be guaranteed upon service parts.

ITEM NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

DESCRIPTION
RETURN HOSE 54"
PRESSURE HOSE 48"
#12 HOSE CLAMP
HYDRAULIC RESERVOIR
1/2-13 X 3 1/2 GR5 BOLT
1/2-13 NYLOCK NUT
RESERVOIR VENT PLUG
3/8-16 X 1 GR5 BOLT
1/2 X 3 1/2 HITCH PIN W/ HAIR PIN
SUCTION HOSE 18"
#16 HOSE CLAMP
RETURN LINE FITTING
FILTER HEAD
FILTER ELEMENT
1/2-13 X 1 1/4 GR5 BOLT
3/8-16 2-WAY LOCK NUT
TANK BRACE
3/8-16 NYLOCK NUT

PART NUMBER
7290
7289
LS5001
7319
NB577
NB281
7379
NB604
NB648
7346
LS4999
7329
LS1112
LS1113
NB647
NB280
7352
NB182

HYDRAULIC PUMP - LS622,LS67525 MODEL
HYDRAULIC PUMP - LS928,LS11534 MODELS
1/8 X 1/2 #3 WOODRUFF KEY
5/16-18 2-WAY LOCK NUT
PUMP PULLEY

LS2001H
LS2002B
024002
NB558
7306

SET SCREW W/ NYLOCK
5/16-18 X 3/4 GR2 BOLT
FENDER BRACKET - RIGHT SIDE - LS11534 ONLY
FENDER BRACKET - LEFT SIDE - LS11534 ONLY
FENDER - LS11534 ONLY
KICKSTAND

NB312
NB143
7417
7418
7428
7398

21
22
23
24
25
26
27
28

SERVICE PARTS
Please have Model and Serial Numbers ready when ordering parts.
Color cannot be guaranteed upon service parts.

ITEM NUMBER
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58

DESCRIPTION
MOTOR BASE / AXLE
TIRE / WHEEL
COTTER PIN
WHEEL DUST COVER
CASTLE NUT
WASHER
TAPERED BEARING
BEARING SEAL
BELT
IDLER ARM
CLUTCH LEVER
SPRING
3/8-16 JAM NUT
HARDENED WASHER
3/8-16 X 2 1/2 GR5 BOLT
5/16-18 FLANGE NUT
IDLER SPRING MOUNT
WIRE LINK FOR IDLER SPRING
SHOULDER BOLT
IDLER PULLEY
WASHER
BELT COVER
#14 x 3/4 SELF-TAPPING SCREW
SAFETY CLIP PIN
TOWING TONGUE
TOWING TONGUE - LS11534
TRAVEL LOCK
SAFETY CHAIN W/ HOOK
2" BALL COUPLER
3/8-16 X 3 GR5 BOLT
3/8-16 X 3 1/2 GR5 BOLT

PART NUMBER
7297
7296
NB633
2203DC
2203CN
NB184
2203B
2203S
644
6681TK
7358
682S
NB174
NB196
NB619
NB170
2046
BRS6H
NB220
B527
NB272
7321
NB161
H11
7343
7168
7441
7366
7365
NB164
NB649

59
60
63

67
73

69
70

75
77

81
76
81A

BEAM DETAIL
ALL MODELS
NOT ALL PARTS ARE ON ALL MODELS
ITEM NUMBER
59
60
61
62
63

64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
81A

DESCRIPTION
CLIP PIN
STEEL PIN
HYDRAULIC FITTING
STATIONARY LINE ASSEMBLY
RAM CYLINDER - LS622 MODELS
RAM CYLINDER - LS928&LS67525 MODEL
RAM CYLINDER - LS11534&LS12534DMODEL
1/2-13 X 3 GR5 BOLT
SPLITTING WEDGE
1/2-13 X 2 1/2 GR5 CARRIAGE BOLT
RETURN LINE FITTING
1/2-13 JAM 2-WAY LOCK NUT
2-WAY PIPE NIPPLE
MASTER CHAIN LINK
COTTER PIN
VALVE INLET FITTING
VALVE CONTROL W/ LEVER
BEAM WELDMENT
BEAM WELDMENT - LS12534D MODEL
1/4 X 1 CLEVIS PIN
1/2-13 NUT
VALVE LEVER & GRIP
THIN GIB PLATE
THICK GIB PLATE
BOTTOM GIB PLATE
LOCK WASHER
FLAT WASHER

PART NUMBER
NB642
7293
7291
7288
7284
7354
7355
NB131
7233
NB643
7329
NB121
7292
7424
NB597
7387
7287
7624
7384
NB522
NB213Z
7423/7425
7388
7237
7333
NB508
NB555

ENGINE DETAIL
LS10528C MODELS
ITEM #
89
90
91
92
93
94
95
96
106
182
NOTSHOWN
NOTSHOWN
NOTSHOWN

DESCRIPTION
ENGINE
5/16-18 X 1 1/4 GR5 BOLT
5/16-18 2-WAY LOCK NUT
UPPER SPACER
ENGINE PULLEY
LOWER SPACER
BELLEVILLE WASHER
7/16-20 X 1 GR5 BOLT W/ NYLOCK
KEYSTOCK
WASHER
WIRING HARNESS - LS12534D MODEL
OIL DRAIN VALVE
FUEL SHUT OFF VALVE (INLINE)

PART #
N/A
NB504
NB558
BB105SL
BB105
BB105S
699
NB452N
9031
TR150W
7416
AS122
7414

93
94

106
95

182

100

ENGINE DETAIL

101

LS728C MODELS

102
99
104

103

105

ITEM #
97
98
99
100
101
102
103
104
105

DESCRIPTION
ENGINE
5/16-18 X 2 1/2 GR5 BOLT
5/16-18 2-WAY LOCK NUT
5/16-18 X 1 1/4 GR5 BOLT
KEYSTOCK
SET SCREW W/ NYLOCK
ENGINE PULLEY - LS622
BELLEVILLE WASHER
3/8-24 X 1 BOLT W/ NYLOCK

PART #
N/A
NB138
NB558
NB504
9030
NB312
7323
699
NB238N

NOTES:
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

SPECIFICATIONS
Models
LS728C

LS10528C

Splitting
Force

28 Tons

Engine

7 HP Briggs and
Stratton Intek

10.5 HP Briggs
and Stratton I/C

Splitting
Positions

Horizontal and
Vertical

Cylinder
Size

4 1/2" X 24"

Pump

2 Stage with Heavy
Duty Bearings

Pump
Specs

11 Gallons Per
Minute

16 Gallons Per
Minute

Valve

Auto Return

Oil
Capacity

Approx. 4.5 Gallon

Maximum
Log length

24"

Tire Specs

4.00 X 4.80 X 8
with High Speed
Bearings

Metal
Fenders

Ball Hitch

2" Ball

Unit
Weight

535 Lbs

550 Lbs

LOG SPLITTER
OWNER’S
MANUAL

MODEL NO.
LS728C
LS10528C

HOW TO ORDER
REPAIR PARTS:
Each Log Splitter has its own serial number. Each engine has
its own serial number. The serial number for the Log Splitter
will be found on the right hand side of the hydraulic oil
reservoir. The serial number for the engine will be found on
the top of the blower fan housing.
All Log Splitter parts listed herein may be ordered directly
from Swisher Mower & Machine Co. Inc., your nearest
Swisher dealer, or from our website.
All engine parts may be ordered from the nearest dealer of the
engine supplied with your log splitter. Parts subject to change
without notice.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
*
*
*
*

PRODUCT – SWISHER LOG SPLITTER
SERIAL NUMBER - _______________
MODEL NUMBER - _______________
ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION

www.swisherinc.com
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093

SWISHER MOWER & MACHINE CO. INC.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 20
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2006:06:23 06:26:12
Modify Date                     : 2006:06:23 06:26:12
Title                           : Microsoft PowerPoint - 11815
Creator                         : Pscript.dll Version 5.0
Author                          : Administrator

EXIF Metadata provided by EXIF.tools

Swisher LS728C, LS10528C Microsoft 11815 User Manual To The 78e8e8eb D163 4683 A214 Bd659bd23cda

Navigation menu

Versions of this User Manual:

Views

Navigation