Sysgration AXM-403 WIRELESS OPTICAL MOUSE User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	742150
Application ID	xl/H1XVy6qwsse2QmbP2dQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.7kB (58775 bits)
Date Submitted	2006-12-26 00:00:00
Date Available	2006-12-26 00:00:00
Creation Date	2006-12-15 13:58:35
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2006-12-15 13:58:35
Document Title	Microsoft Word - 文件1
Document Creator	PScript5.dll Version 5.2
Document Author:	aa

Wireless Optical Mouse / Brand Name: SANYO / Model No.: AXM403IPM, SYMS-403I
Wireless Optical Mouse
SANYO
AXM403IPM, SYMS-403I
1. Connecting with Computer:
The first time you take out this
mouse and receiver from the
packing, Factory Preset ID
enables Plug and Play function.
Plug the Receiver into PC USB
Port . Under Win2000 or higher ,
wait for the OS to detect the RF
device. Under Win98 or lower
installation of driver for the
device is necessary.
Insert the batteries into
the mouse and move it for a while , then it starts
working .
2. Inserting Batteries:
A. Push the battery cover
Compartment backwards
and open it.
B. Insert 2 AAA batteries Into
compartment with correct
orientation .
C. Slide the battery cover int
the compartment and
close the cover .
4. Power Saving Mode:
A. Suspend Mode :
Keep mouse stationary for 10 minutes, mouse
will be automatically
set to Suspend Mode. Press left
button to wake up the mouse
again.
3. ID Link:
When Factory ID has been
changed or wish to be changed ,
link ID as
below :
A. Press the ID button on the
top of the receiver and the
led on it starts blinking .
B. Press the ID button on the
bottom of the mouse .
If blinking of that led turns
faster , ID Link is OK .
! ID linking should be completed within
10 seconds or connection would be failed
connected when Low Battery Alert Led never
B. Power Off Mode :
When you wish to set the mouse to power off fades out.
mode, press mouse ID for 3 seconds. The F. Ask for maintenance solution from your
Optical Led will flash once and then fade out retailer and engineer . Personally taking apart
showing mouse power is already off. Press ID prohibited after trouble happened.
switch for waking up again .
7. Trouble Shooting:
A. When mouse doesn＇t respond, check the
battery power status, and link ID again.
B. Be sure the two DC Jacks be connected to
the right respective mouse or receiver DC
sockets
C. Check the battery pole if the optical Led
is still off after inserting batteries.
FCC Note :
CE Safety Statements
This device complies with Part 15 of the FCC rules, operation is subject
This device has bee tested and found to to the following two conditions.
（1）This device may not cause harmful interference and,
comply with the requirements set up in the （2）This
device must accept any interference received,
council directive on the approximation of the
including interference that may cause undesired operation .
law of member states relating
to EMC This equipment has been tested and comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules.
Directive 89/336/EEC, Low Voltage Directive These limits are designed to provide reasonable protection. This
equipment generates, uses and can radiated radio frequency
73/23/EEC and R&TTE Directive 99/5/EC.
The product has been approved for LVD
and covered the following countries:
Austria, Belgium, Denmark, France,
Finland, Germany, Greece, Iceland,
Ireland, Italy, Luxembourg, Netherlands,
Norway, Portugal, U.K., Spain, Sweden
energy and, if not installed and used in accordance with
the instructions, may cause harmful intererence to radio
communications.
However,
there
is
no guarantee that
interference will not occur in a particular installation if this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not expressly approved by the
party
responsible for compliance could void the user＇s authority to
operate the equipment.
The antenna(s) used for this transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c779bdb2-dd13-4f6a-9ffe-5d67dd08933c
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2006:12:15 13:58:35+08:00
Create Date                     : 2006:12:15 13:58:35+08:00
Creator Tool                    : PScript5.dll Version 5.2
Document ID                     : uuid:89cc4ff8-cc7d-4057-9032-f0427a503c74
Format                          : application/pdf
Title                           : Microsoft Word - 文件1
Creator                         : aa
Author                          : aa

EXIF Metadata provided by EXIF.tools