Systech SLZW0001 SLZW0001 User Manual SLZW0001 revised

Download:
Mirror Download [FCC.gov]
Document ID	1906961
Application ID	HzV3uW2wlzcAuUFkDxdgdQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.66kB (108242 bits)
Date Submitted	2013-02-25 00:00:00
Date Available	2013-02-25 00:00:00
Creation Date	2013-02-22 16:13:54
Producing Software	Acrobat Distiller 8.3.1 (Windows)
Document Lastmod	2013-02-22 16:13:54
Document Title	Microsoft Word - SLZW0001 User Manual revised.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	DBare

SLZW0001 User Manual
Instructions for Installation:
1. Unplug the SysLINK.
2. Observe proper ESD (grounding) procedures.
3. Remove the four screws on the bottom of the SysLINK unit.
4. Remove the top cover of the SysLINK by pressing on the tabs in the rear of the unit.
5. Open the SLZW0001 box and carefully remove the card.
6. Select any open option card connector in the SysLINK and insert the pins from the SLZW0001 into the
connector, confirming the three screw holes line up with the mezzanine locations.
7. Insert the three screws supplied with the SLZW0001 into their respective holes and tighten. Be careful
not to overtighten the screws.
8. Re-assemble the SysLINK unit.
9. Power on the SysLINK – the LED corresponding to the Systech Z-Wave Option Card will be Yellow at
first, then Green when SLZW0001 is active.
Instructions for Labeling the Unit:
Attach a label on the bottom of the Syslink that states the below:
Contains: FCCID: KJM-SLZW0001 and IC: 3288A-SLZW0001.
This device complies with FCC Rules standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Include the following statements in the user manual for the final product:
Notice: This device complies with FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Avis: Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son
fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences
et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Notice: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Avis: Sous la réglementation d'Industrie Canada, ce transmetteur radio ne peut fonctionner qu’en utilisant
seulement une antenne d'un type et d’un maximum (ou moins) de gain approuvé pour l'émetteur par Industrie
Canada. Pour réduire des potentielles interférences radio pour les autres utilisateurs, le type d'antenne et son
gain doivent être choisis de sorte que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui
est nécessaire pour une communication réussie.
Warning: Changes or modifications not expressly approved by Systech Corporation could void the user’s
authority to operate the equipment.
The SLZW0001 module is approved for co-location use with the following modules. Co-location use is
prohibited with other radio equipment or modules.
Vendor
Model
Cellular Module (1 of these)
Fusion
FW2770p
Foxlink
MV84PG
E362
Novatel
EM820W
Hauwei
Wi‐Fi Module
SparkLAN
WPER‐150GN
Bluetooth Module (1 of these)
Vencer
VD‐2100
ENW89820A1KF
Panasonic
Zigbee Module (1 of these)
Anaren
A2530E24A or A2530E24C
A8520E24A91 or A8520E24C91
Anaren
FCC ID
XU9‐FW2770P
QVZ‐MV84PG
PKRNVWE362
QISEM820W
RYK‐WPER150GN
VHVBTVD2100
T7VPAN17
X7J‐A11091301
X7J‐A10051702
The SLZW0001 module, when used in combination with the above modules must be installed in a manner so as
to provide at least 21.5 cm separation distance from the antenna to the body of a user of the final product.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:02:22 16:13:54-08:00
Create Date                     : 2013:02:22 16:13:54-08:00
Format                          : application/pdf
Title                           : Microsoft Word - SLZW0001 User Manual revised.doc
Creator                         : DBare
Producer                        : Acrobat Distiller 8.3.1 (Windows)
Document ID                     : uuid:3bbcae71-8803-4d7a-b5c1-6bb5c3a8c6c1
Instance ID                     : uuid:c6894648-3ead-4089-87d7-3639acc7630c
Page Count                      : 2
Author                          : DBare

EXIF Metadata provided by EXIF.tools