Systems and Technology STAVL0358 INTELLI TRAC X User Manual users manual

Systems & Technology Corp. INTELLI TRAC X users manual

users manual

*** USER’S MANUAL ***FCC ID : RLS-STAVL0358
Federal Communications Commission (FCC) Warning THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERECE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. The antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be do-located or operating in conjunction with any other antenna or transmitter. The antenna used must not exceed 7 dBi gain for mobile or fixed operation.
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio / TV technician for help. Warning : A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
IntelliTrac® X Series Hardware Installation Guide 1. Install SIM Card To install the SIM card: -Press the yellow button to eject the SIM card holder.-Before insert the SIM card, make sure the PIN code has been disabled. - Insert the SIM card. - Check that it fit into place correctly.Copyright © 2003 Systems & Technology Corporation
2. Install GPS and GSM AntennasConnect GPS antenna to the GPS connector. The optimum location for the GPS antenna is on the roof of thevehicle. The covert and GPS antenna are directional, make sure they are facing up and laying as flat as possible. Secure them in place with glue, or zip ties. Note : Do not block or cover the GPS antenna with metal.Connect GSM antenna to the GSM connector. The GSM antenna is non-directional, so you can hide it in any place of vehicle. 3. Install Power Cable 123412345678910111212345678910Power Input OutputPower Connector1 : Ground2 : Ignition Key3 : BAT. +8V ~ +32V4 : Mute ControlCopyright © 2003 Systems & Technology Corporation
(1) General Installation (Without immobilizer installed) Connect Ground(-Black) and BAT(+Red) wires to the battery of vehicle. (2) With immobilizer installed Connect Ground (-Black) and BAT (+Red) to the battery of vehicle. Connect Ignition Key (Pink) to the IGNITION wire.Copyright © 2003 Systems & Technology Corporation
4. Install Immobilizer Relay (Optional) (1) If the wireless relay terminal is same as car original fuel pump (or ignition, or starter) relay terminal,please just unplug the car original relay, then plug in the wireless relay.(2) If the wireless relay terminal is different with car original fuel pump (or ignition, or starter) relay terminal : Please plug the wireless relay into the spare relay socket, then a. Connect the socket Black wire to Ground. b. Connect the socket Red wire to IGNITION c. Blue & Green wires are for engine disable cutting (ignition or fuel pump or starter…)(3) For security reason, it is better do NOT install the wireless relay at IGNITION key lock area. May install the wireless relay in the hood or near the fuel pump or any confidential place for engine disable cutting. Copyright © 2003 Systems & Technology Corporation
5. Install Input Cable 123412345678910111212345678910Power Input OutputInput Connector1 : Input12 : Input2/ACC3 : Input34 : Input45 : Input56 : Input67 : Input78 : Input89 : Analog Input110 : Analog Input211 : Vout +5V12 : GroundThe Input number 1, 2, 3, 4 are positive triggered inputs and Input number 5, 6, 7, 8 are negative triggered inputs. If you would like to use power saving function, please connect the Input2/ACC to ACC wire. Theanalog inputs are reserved. Copyright © 2003 Systems & Technology Corporation
Positive Trigger:Negative Trigger:Copyright © 2003 Systems & Technology Corporation
6. Install Output Cable 123412345678910111212345678910Power Input OutputOutput Connector1 : Output12 : Output23 : Output34 : Output45 : Output56 : Output67 : Output78 : Output7 (via relay)9 : External Output Power10 : GroundThe output number 1, 2, 7 are positive triggered outputs and output number 3, 4, 5, 6 are negative triggered outputs. Pin number 7 and 8 are controlled by the same signal (OutputID = 7), Pin7 is positive trigger and pin8 is negative trigger. The OutputID = 8 is reserved for immobilizer control. Copyright © 2003 Systems & Technology Corporation
7. LED Indicators Status Description There are 4 LEDs in front panel. When you power on the unit, these 4 LEDs will become blinking. Afterblinking several times, IntelliTrac X8 will start the modem which is inside the unit. In this time, the ERR led light is still bright. This is normal condition. Waiting for several seconds, the ERR led light will put out. Thenyou can start to manipulate the IntelliTrac X8. Note 1: If the ERR led light is bright continuously, that means there is something wrong with IntelliTrac X8. You can not execute command to IntelliTrac X8.Note 2: Before powering on the IntelliTrac X8, please make sure you have inserted the SIM card. Otherwise, the ERR led light will not put out.PWR LED Status FunctionOff Power off90 ms On / 2 secs Off The device is running in power saving mode.ʳ500ms On / 500ms Off Reset procedure is in progress On Power on GPS LED Status FunctionOff The GPS is off or running in power saving mode. 1 sec On / 1 sec Off No GPS satellites signal received On GPS Ready GSM LED Status FunctionOff The device is off or running in power saving mode. 600 ms On / 600ms Off No SIM card inserted or no PIN entered, or network search in progress, or network login in progress. Copyright © 2003 Systems & Technology Corporation
90 ms On / 3 secs Off Logged to network. No call in progress.ʳOn Voice/Data call connected ERR LED Status FunctionOff The device is ready On The device is not ready Copyright © 2003 Systems & Technology Corporation
8. Unit ConfigurationConnect the download cable between IntelliTrac unit and PC serial interface and use IntelliTracInstallWizard program to configure a new IntelliTrac unit. Please refer to the InstallWizard User Manual for more detail information.Copyright © 2003 Systems & Technology Corporation

Navigation menu