Systems and Technology STAVL0358 INTELLI TRAC X User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	386487
Application ID	8sF7u0rxPdt4JWurVKvdIg==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.26kB (115778 bits)
Date Submitted	2004-01-06 00:00:00
Date Available	2004-01-05 00:00:00
Creation Date	2003-12-16 09:23:08
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2003-12-31 15:31:57
Document Title	users manual

***
USER’S MANUAL ***
FCC ID : RLS-STAVL0358
Federal Communications Commission (FCC) Warning
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERECE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
The antenna used for this transmitter must be installed to
provide a separation distance of at least 20cm from all
persons and must not be do-located or operating in
conjunction with any other antenna or transmitter. The
antenna used must not exceed 7 dBi gain for mobile or fixed
operation.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio / TV technician for
help.
Warning : A shielded-type power cord is required in order to meet
FCC emission limits and also to prevent interference to the nearby
radio and television reception. It is essential that only the supplied
power cord be used.
Use only shielded cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
IntelliTrac® X Series
Hardware Installation Guide
1. Install SIM Card
To install the SIM card:
Press the yellow button to eject the SIM card holder.
Before insert the SIM card, make sure the PIN code has been disabled.
Insert the SIM card.
Check that it fit into place correctly.
Copyright © 2003 Systems & Technology Corporation
2. Install GPS and GSM Antennas
Connect GPS antenna to the GPS connector. The optimum location for the GPS antenna is on the roof of the
vehicle. The covert and GPS antenna are directional, make sure they are facing up and laying as flat as
possible. Secure them in place with glue, or zip ties.
Note : Do not block or cover the GPS antenna with metal.
Connect GSM antenna to the GSM connector. The GSM antenna is non-directional, so you can hide it in any
place of vehicle.
3. Install Power Cable
11
10 12
10
Power
Input
Output
Power Connector
1 : Ground
2 : Ignition Key
3 : BAT. +8V ~ +32V
4 : Mute Control
Copyright © 2003 Systems & Technology Corporation
(1) General Installation (Without immobilizer installed)
Connect Ground(-Black) and BAT(+Red) wires to the battery of vehicle.
(2) With immobilizer installed
Connect Ground (-Black) and BAT (+Red) to the battery of vehicle.
Connect Ignition Key (Pink) to the IGNITION wire.
Copyright © 2003 Systems & Technology Corporation
4. Install Immobilizer Relay (Optional)
(1) If the wireless relay terminal is same as car original fuel pump (or ignition, or starter) relay terminal,
please just unplug the car original relay, then plug in the wireless relay.
(2) If the wireless relay terminal is different with car original fuel pump (or ignition, or starter) relay
terminal :
Please plug the wireless relay into the spare relay socket, then
a. Connect the socket Black wire to Ground.
b. Connect the socket Red wire to IGNITION
c. Blue & Green wires are for engine disable cutting (ignition or fuel pump or starter…)
(3) For security reason, it is better do NOT install the wireless relay at IGNITION key lock area. May
install the wireless relay in the hood or near the fuel pump or any confidential place for engine
disable cutting.
Copyright © 2003 Systems & Technology Corporation
5. Install Input Cable
11
10 12
10
Power
Input
Output
Input Connector
1 : Input1
2 : Input2/ACC
3 : Input3
4 : Input4
5 : Input5
6 : Input6
7 : Input7
8 : Input8
9 : Analog Input1
10 : Analog Input2
11 : Vout +5V
12 : Ground
The Input number 1, 2, 3, 4 are positive triggered inputs and Input number 5, 6, 7, 8 are negative triggered
inputs. If you would like to use power saving function, please connect the Input2/ACC to ACC wire. The
analog inputs are reserved.
Copyright © 2003 Systems & Technology Corporation
Positive Trigger:
Negative Trigger:
Copyright © 2003 Systems & Technology Corporation
6. Install Output Cable
11
10 12
10
Power
Input
Output
Output Connector
1 : Output1
2 : Output2
3 : Output3
4 : Output4
5 : Output5
6 : Output6
7 : Output7
8 : Output7 (via relay)
9 : External Output Power
10 : Ground
The output number 1, 2, 7 are positive triggered outputs and output number 3, 4, 5, 6 are negative triggered
outputs. Pin number 7 and 8 are controlled by the same signal (OutputID = 7), Pin7 is positive trigger and
pin8 is negative trigger. The OutputID = 8 is reserved for immobilizer control.
Copyright © 2003 Systems & Technology Corporation
7. LED Indicators Status Description
There are 4 LEDs in front panel. When you power on the unit, these 4 LEDs will become blinking. After
blinking several times, IntelliTrac X8 will start the modem which is inside the unit. In this time, the ERR led
light is still bright. This is normal condition. Waiting for several seconds, the ERR led light will put out. Then
you can start to manipulate the IntelliTrac X8.
Note 1: If the ERR led light is bright continuously, that means there is something
wrong with IntelliTrac X8. You can not execute command to IntelliTrac
X8.
Note 2: Before powering on the IntelliTrac X8, please make sure you have inserted the SIM card. Otherwise,
the ERR led light will not put out.
PWR LED Status
Function
Off
Power off
90 ms On / 2 secs Off
The device is running in power saving mode.ʳ
500ms On / 500ms Off
Reset procedure is in progress
On
Power on
GPS LED Status
Function
Off
The GPS is off or running in power saving mode.
1 sec On / 1 sec Off
No GPS satellites signal received
On
GPS Ready
GSM LED Status
Function
Off
The device is off or running in power saving mode.
600 ms On / 600ms Off
No SIM card inserted or no PIN entered, or network search in
progress, or network login in progress.
Copyright © 2003 Systems & Technology Corporation
90 ms On / 3 secs Off
Logged to network. No call in progress.ʳ
On
Voice/Data call connected
ERR LED Status
Function
Off
The device is ready
On
The device is not ready
Copyright © 2003 Systems & Technology Corporation
8. Unit Configuration
Connect the download cable between IntelliTrac unit and PC serial interface and use IntelliTrac
InstallWizard program to configure a new IntelliTrac unit. Please refer to the InstallWizard User
Manual for more detail information.
Copyright © 2003 Systems & Technology Corporation

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:12:16 09:23:08Z
Modify Date                     : 2003:12:31 15:31:57+08:00
Page Count                      : 13
Creation Date                   : 2003:12:16 09:23:08Z
Mod Date                        : 2003:12:31 15:31:57+08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2003:12:31 15:31:57+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools