Systems and Technology STAVL1239 GPS Watch Tracking Device User Manual U

Systems & Technology Corp. GPS Watch Tracking Device U

user manual

1 CAREU WT1 Vehicle Tracker User Guide Version: 0.1 Reference No.: Date: November 20, 2012 SYSTEMS & TECHNOLOGY CORP.
2General Information If any breakdown occurs due to the operation of the described product or users’ improper handling in accordance with the instructions of the document, S&T shall be liable for the General Conditions based on the delivery of the described product and the content of the document. This product is not designed for the use of life support appliances, devices or systems and thence a malfunction of the product might reasonably be expected to make personal injury. S&T customers using or selling this product for such applications will take the risk on their own; therefore, it must be agreed S&T will be fully indemnified from any damages due to illegal use or resale. All information in this document is subject to change without notice at any time. Disclaimer The information, specification, images and photos in this user guide are subject to change without notice and without obligation to notify any person of such revision change. Copyright This user guide, including all photographs, illustrations and software, to name a few, is protected under international copyright laws, with all rights reserved. This document contains confidential, restricted and proprietary information that it has been exclusively prepared for the internal use of certain designated S&T employees, and may not be duplicated or distributed, in whole or in part, without the prior written consent of S&T’s authorized delegates. Any illegal copying and disclosure of the document are absolutely prohibited, and violators are liable to the damages caused. © Systems & Technology Corp. All Rights Reserved
3 Table of Contents Chapter 1 Introduction ................................................................................................. 5 1.1 Features ........................................................................................................... 5 1.2 Scope ............................................................................................................... 6 1.3 About WT1 ..................................................................................... …………….6 1.4 Hardware Architecture ..................................................................................... 7 1.5 Related Document ........................................................................................... 8 Chapter 2 Taking a Tour of CAREU WT1 .................................................................... 2.1 Dimensions ...................................................................................................... 9 2.2 Laterel View.....................................................................................................10 2.3 Front View........................................................................................................11 Chapter 3 Getting Started with CAREU WT1 ..............................................................12 3.1 USB Device Driver Installation ........................................................................ 12 3.2 Device Configuration...................................................................................... 19 3.3 Communication Settings ................................................................................ 23 3.4 GPS Tracking Configurations......................................................................... 25 3.5 Firmware Upgrade ......................................................................................... 28 Chapter 4 Technical Specification ............................................................................. 30 Chapter 5 Regulation .................................................................................................. 34
Chapter 1 CAREU WT1 Vehicle Tracker User Chapter 1. Introduction Thank you for your purchasing the CAREU W T1 Vehicle Tracker. We are very pleased to introduce you our excellent product, and you will enjoy great benefits by applying such a smart device. The CAREU WT1 Vehicle Tracker is a n all-in-one device that integrates multiple applications of GPS (Global Position System), GSM (Global System for Mobile Communication) and GIS (Geographic Information Systems) with each other. Designed with the latest GPS technology, the CAREU WT1 delivers positioning message by GSM wireless transmission to GIS platform, and then helps back-end users proceed with the analysis and the applications of vehicle transport, management, anti-theft, security and tracking. 1.1 Features • Cost effective and easy installation • SMS, GPRS TCP/ UDP, USSD, FTP communications • Geo-fencing reports • Remote configuration • Real-time tracking (time, distance interval or intelligent mode, and heading) • Intelligent power management • Power low/lost alarm • Journey report wireless downloads • GSM/GPRS simultaneously • Firmware upgrade over the air (via GPRS from FTP) • Up data log capacity
CAREU WT1 Lite Vehicle Tracker User Guide 1.2 Scope This document will guides you to start the CAREU WT1 Vehicle Tracker. However, as this document contains basic device configuration only, please see the CAREU WT1 Protocol Document for the advanced information. 1.3 About WT1 The CAREU WT1 Vehicle Tracker transmits the wireless signals such as location, peripheral, and vehicle control data to a control center. The onboard GPS receiver provides users with location data including speed, direction, mileage and altitude. It uses an onboard GSM/ GPRS module to accomplish wireless transmission. A microcontroller can probe location and command data at regular intervals, derive actions from location, peripheral and control data, and execute such actions. Among the best features of the CAREU WT1 Vehicle Tracker, in particular, they transmit data in ASCII mode or binary mode. Peripheral data indicates the status of various peripherals connected to and/or controlled by the device. The peripherals include, but not limited to, door locks/un-locks, starter interrupt, ignition, battery, engine and panic button. The firmware in the device applies intelligent filtering to overcome coverage limitations for both GPS and GSM/GPRS networks. Motion sensor controls the status of the device, whether in sleep, idle or fully-powered mode, and thereby controls the amount of current consumed by the device. Backup battery and tamper sensing GPS Antennas primarily indicate the loss of Main Power and the interruption of GPS antenna connectivity. The device supports over-the-air firmware upgrade to deliver additional functionality without physically touching the device once installed. In consideration of technicality and marketability, the CAREU WT1 has so many excellences to be competitive enough to stand out in the market. With regard to the technicality, the CAREU WT1 saves and records more data even under inactive communication staus, and it also provides better power management, coexistence of GPRS and SMS modes. When it comes to the marketability, the CAREU WT1 users are provided with the convenience that its firmware can be upgraded through mini USB without disassembling the device.
Chapter 1 CAREU WT1 Vehicle Tracker User 1.4 Hardware Architecture As hardware is concerned, the CAREU WT1 is comprised of a micro-controller, regulator, GPS receiver, GSM/GPRS modem, G-Force sensor, flash memory data storage, I/Os interface and LED status indicators. • Users can connect PC's HyperTerminal to the Diagnostic/setting port for the AVL configuration. • G-Sensor for man down warning.
CAREU WT1 Lite Vehicle Tracker User Guide 1.5 Related Document [1] CAREU WT1 Protocol Document
CAREU WT1 Vehicle Tracker User Chapter 2. Taking a Tour of CAREU WT1 This chapter will guide you to the major connectors of the WT1 device. 2.1 Dimensions
CAREU WT1 Lite Vehicle Tracker User Guide 2.2 Lateral view No. Name Description Red Button SOS SOS Function,User define Message & Action mode Blue Button Page LCD View change key,User define function.
CAREU WT1 Vehicle Tracker User 2.3 Front View No. Name Description Micro USB USB USB for change battery & Function set. Reset Button Reset H/W Reset Key.
CAREU WT1 Lite Vehicle Tracker User Guide Chapter 3. Getting Started with CAREU WT1 3.1 USB Device Driver Installation The CAREU WT1 communicates with your host computer by either RS-232 or USB interface. In some newer editions of Windows XP, the CAREU WT1 device can be installed as a "virtual COM port" device whereby the CAREU WT1 would automatically access Windows XP's inbox USB drivers. While in some other earlier editions of Windows XP, you would need to manually install the USB driver for the CAREU WT1 device. In the following content of this section, you will be guided to how the installation can be done in both cases. To install the device driver for the CAREU WT1, connect the CAREU WT1 device to your system with an USB cable as mentioned in Mini USB Cable Connection on section 3.1. As soon as the connection is made between the CAREU WT1 and your computer, a balloon appears above the notification area saying an USB device is found. Click on this balloon to start the [Found New Hardware] wizard. Select No, not this time. Press the Next button to proceed.
CAREU WT1 Vehicle Tracker User 1. Automatic Installation If the wizard prompts to help you install the software for "STMicroelectronics Virtual COM Port". Select Install the software automatically (Recommended). Press the Next button to proceed. The wizard proceeds to install the driver.
CAREU WT1 Lite Vehicle Tracker User Guide The installation completes. In [Device Manager], the CAREU WT1 device is included under Ports (COM & LPT) as "STMicroelectronics Virtual COM Port". COM port number is displayed as well.
CAREU WT1 Vehicle Tracker User 2. Manual Installation After you select No, not this time, if the wizard only prompts to help you install software for "USB device", you need to manually install the driver. Select Install from a list or specific location (Advanced). Press the the Next button to proceed.
CAREU WT1 Lite Vehicle Tracker User Guide Select Search for the best driver in these locations. Check Include this location in the search. Press the Browse button to assign where your the CAREU WT1 device driver locates on your local disk. Press the OK button. You can download the USB device driver from http://www.systech.com.tw/downloads.php.
CAREU WT1 Vehicle Tracker User Press the Next button to proceed. The wizard proceeds to install the driver.
CAREU WT1 Lite Vehicle Tracker User Guide The installation completes. In [Device Manager], the CAREU WT1 device is included under Ports (COM & LPT) as "S&T Tracker". COM port number is displayed as well.
CAREU WT1 Vehicle Tracker User 3.2 Device Configuration 1. In Windows XP desktop, click Start | All Programs | Accessories | Communications | HyperTerminal. 2. If you are prompted to input the information of your location, complete them to proceed. 3. On the File menu of HyperTerminal, click New Connection. 4. In the Name box, type a name that describes the connection. In the Icon box, click an appropriate icon. Press the OK button to proceed. 5. For Com port properties, configure as follows: Baud Rate --> 115200 bps Data Bits --> 8 Parity --> None Stop Bits --> 1 Flow Control --> None
CAREU WT1 Lite Vehicle Tracker User Guide 6. In the connection that you have just set up, click File | Properties. Select the [Connect To] tab. From the [Connect using] drop down list, select the correct com port by checking it up at Windows XP's [DeviceManager] as previously mentioned on page 21. Go there by clicking Start | Control Panel | System | Hardware | Device Manager.
CAREU WT1 Vehicle Tracker User 7. In the File menu, click Properties. Click the [Settings] tab. Press the ASCII Setup button. 8. In the [ASCII Sending] group box. Select both Send line ends with line feeds and Echo typed characters locally. Press the OK button.
CAREU WT1 Lite Vehicle Tracker User Guide 9. Connect your the CAREU WT1 device to power as mentioned in Power and I/O Cable Connection on page 12. The device startup message will be displayed. 10. In [HyperTerminal] window, type in the command "AT$VERSION?" and press the Enter key. The hardware and firmware version will show. As long as your [HyperTerminal] window appears as the screenshot below, a connection between the device and your system has already been built up and working. It is time to send all configuration commands.
CAREU WT1 Vehicle Tracker User 3.3 Communication Settings The CAREU WT1 Vehicle Tracker communicates with your control center by either SMS or GPRS (TCP/UDP). Before the device is installed into a vehicle, communication parameters should be set. 1. SMS Configuration Use AT$SMSDST command to set a SMS control center phone number or short code. For example, if the SMS control center phone number is +886123456789, the AT$SMSDST command to be issued into HyperTerminal should be: AT$SMSDST=+886123456789 OK Then you can try to use cellular phone or SMS gateway to send a SMS message to the CAREU WT1 device. Send a SMS message --> "AT$MODID?" Device will response: $MODID=101000001 OK This proves a successful mobile phone SMS connection.
CAREU WT1 Lite Vehicle Tracker User Guide 2. GPRS Configuration Set GPRS servers by using the folloiwng commands: AT$APN=internet,username,password (APN=internet, Username=username, Password=password) OK AT$HOSTS=1,0,60.148.19.10,6000 (Server IP address = 60.148.19.10 and Port number =6000) OK AT$RETRY=5,10 (Message retry settings) OK AT$IPTYPE=1 (Using TCP/IP mode) OK AT$GPRSEN=1 (GPRS enable) OK AT$HB=60,1 (Heartbeat setting) OK Please refer to the CAREU WT1 Protocol Document for more command details.
CAREU WT1 Vehicle Tracker User 3.3 GPS Tracking Configurations After the device communication settings are done, the remote GPS tracking is ready to function. The setting of GPS tracking can be done by using AT$PDSR command. For example, AT$PDSR=1,30,0,0,2,0,0,1,1 (Tracking through GPRS by time interval 30 seconds) OK For simple testing GPRS, run the TCP Server U-Series software which is provided by S&T. It is simple server software that can wait for device connection and data.
CAREU WT1 Lite Vehicle Tracker User Guide For advanced testing, you need the software Intelli TracerPlus. Please request this software through your sales contact. You can also apply for a testing account from S&T's FleetWeb solution through your sales contact.
CAREU WT1 Vehicle Tracker User The main page of the Intelli FleetWeb appears as below:
CAREU WT1 Lite Vehicle Tracker User Guide 3.4 Firmware Upgrade The firmware of the CAREU WT1 can only be updated through USB interface. With the firmware loader tool provided by S&T, firmware update can be done for the device. Such firmware loader runs on Windows-based systems. To upgrade the firmware, follow the procedure below: 1). Connect the device to your PC with the USB cable. 2). Connect the device to power. 3). Power on the device. 4). Run ServerUSeries.exe. A window displays as follows: 5). Press browse the button to browse to the firmware provided by S&T. 6). Press the Start button to run the firmware program. 7). After the writing progresses to 100%, it takes about 20 seconds for the update to completes. 8). Firmware update completes.
CAREU WT1 Lite Vehicle Tracker User Guide Chapter 4 Chapter 4. Technical Specification Characteristics Dimensions (L x W x H) 108 x 72 x 31mm Weight 165g Radio Performance Frequency Quad-band 850/900/1800/1900MHz GSM Functionality / GPRS GPRS Mode Multi-slot class 10 GPRS Coding Scheme CS1,CS2,CS3 and CS4 GSM Antenna Internal SIM Interface E- SIM (Built-in mainboard) GPS Functionality Receiver 50 channels Sensitivity (Tracking) -160dBm Antenna Type External GPS active antenna, 3.3V ConnectorSMA female GPS Protocol NMEA 0183 Ver3.0 Onboard Components MCU 32-bit microcontroller Data Memory 8 MB Flash Motion Sensor 3-axes acceleration sensor Led Indicator GPS and GSM Indicator
CAREU WT1 Vehicle Tracker User Interface I/O Button Key Emergency Button Controls Function Button Electrical Power Source 500mA @ +5V Environment Operating Temperature –20 °C to +60 °C Battery Rechargeable Backup Battery 3.7V / 550mAH Note: The specification herein is subject to change without prior notice.
CAREU WT1 Lite Vehicle Tracker User Guide Chapter 4 Systems & Technology Corp. (S&T), founded in 1987, is a market leader in Automatic Vehicle Locating (AVL) solutions, Geographical Information Systems (GIS) and navigation. It has formed a professional development team to innovate the most advanced and comprehensive GPS tracking products for the customers and has built a global service network to provide non-stop services and support. With the well-established marketing networks of over 100 distributors in the world, S&T is your trustworthy tracking solution provider. For more product information, please contact S&T by Email, phone or fax. Web Site http://www.systech.com.tw Email avl@systech.com.tw Phone +886-2-2698-1599 Fax +886-2-2698-1211
CAREU WT1 Vehicle Tracker User Chapter 5. Regulation Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. RF Exposure Information (SAR)This device meets the government’s requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands.
CAREU WT1 Lite Vehicle Tracker User Guide Chapter 4 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
CAREU WT1 Vehicle Tracker User fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Statement: A minimum separation distance of 0 cm must be maintained between the user’s body and the device, including the antenna during body-worn operation to comply with the RF exposure requirements in Europe.
CAREU WT1 Lite Vehicle Tracker User Guide Chapter 4 DoC 法規版本法規版本法規版本法規版本 Declaration of Conformity

Navigation menu