Systems and Technology STAVL1450 GPS Vehicle Tracking Device User Manual
Systems & Technology Corp. GPS Vehicle Tracking Device
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2498928 |
| Application ID | FPpZthXKFwr5Q1Ub4BD1Tg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 61.46kB (768307 bits) |
| Date Submitted | 2015-01-14 00:00:00 |
| Date Available | 2015-07-16 00:00:00 |
| Creation Date | 2014-12-29 09:48:06 |
| Producing Software | doPDF Ver 7.3 Build 388 (Windows XP Professional Edition (SP 3) - Version: 5.1.2600 (x86)) |
| Document Lastmod | 2015-01-09 14:54:57 |
| Document Title | User Manual |
CAREU U1 PLUS User Gu CAREU U1 PLUS User Guide Version: 0.1 Reference No.: AVL Date: 2014/12/26 SYSTEMS & TECHNOLOGY COR General Information If any breakdown occurs due to the operation of the described product or users’ improper handling in accordance with the instructions of the document, S&T shall be liable for the General Conditions based on the delivery of the described product and the content of the document. This product is not designed for the use of life support appliances, devices or systems and thence a malfunction of the product might reasonably be expected to make personal injury. S&T customers using or selling this product for such applications will take the risk on their own; therefore, it must be agreed S&T will be fully indemnified from any damages due to illegal use or resale. All information in this document is subject to change without notice at any time. Disclaimer The information, specification, images and photos in this user guide are subject to change without notice and without obligation to notify any person of such revision change. Copyright This user guide, including all photographs, illustrations and software, to name a few, is protected under international copyright laws, with all rights reserved. This document contains confidential, restricted and proprietary information that it has been exclusively prepared for the internal use of certain designated S&T employees, and may not be duplicated or distributed, in whole or in part, without the prior written consent of S&T’s authorized delegates. Any illegal copying and disclosure of the document are absolutely prohibited, and violators are liable to the damages caused. © Systems & Technology Corp. All Rights Reserved Table of Contents Chapter 1 introduction. ..................................................................................... 1 1.1Features........................................................................................................ 1 1.2 Scope ........................................................................................................... 1 1.3 Overview ..................................................................................................... 1 1.4 Hardware Architecture ................................................................................ 3 1.5 Related Document ....................................................................................... 3 Chapter 2 Taking a Tour of CAREU U1 PLUS ................................................... 4 2.1 Dimensions .................................................................................................. 4 2.2 PIN Assignment ............................................................................................ 4 Chapter 3 Getting Started with CAREU U1 PLUS ............................................ 6 3.1 Device Configuration.................................................................................... 6 3.2 Communication Settings .............................................................................. 9 3.3 GPS Tracking Configurations ...................................................................... 10 3.4 Firmware Upgrade ..................................................................................... 12 Chapter 4 Technical Specification ................................................................ 13 Chapter 5 Regulation ................................................................................... 16 Chapter 6 Safety Information....................................................................... 17 Chapter 1 introduction. Designed with the latest GPS technology, the CAREU U1 PLUS delivers positioning message by wireless transmission to GIS platform, and then helps back-end users proceed with the analysis and the applications of vehicle transport, management, anti-theft, security and tracking. A microcontroller can probe location and command data at regular intervals, derive actions from location, peripheral and control data, and execute such actions. Peripheral data indicates the status of various peripherals connected to and/or controlled by the device. Among the best features of the CAREU U1 PLUS Vehicle Tracker, in particular, they transmit data in ASCII mode (Intellitrac X Series compatible mode) or binary mode. 1.1 Features ● ● ● ● ● ● ● ● ● ● ● ● ● SMS,GPRS/UMTS/HSPA TCP/UDP, USSD, FTP Real-time tracking (Time, Distance Interval or Intelligent Mode, and Heading) Firmware upgrade over the air ( form FTP) Journey report wireless download Battery low alert Geofence reports Mileage reports User-defined reports 6-Axis Sensor NMEA-0183 Output for Navigation GPS Antenna Destroyed Alarm CAN BUS interface (optional) 10/100 Ethernet (optional) 1.2 Scope This document will guides you to start the CAREU U1 PLUS Vehicle Tracker. However,as this document contains basic device configuration only, please see the CAREU U1 PLUS Protocol Document for the advanced information. 1.3 Overview Device Overview 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. GPS LED GSM LED Power Connector RS-485/CAN Connector I/O Connector Serial Connector GSM Antenna Connector GPS Antenna Connector Reset Switch RJ45 Connector Remote Receiver Connector 1.4 Hardware Architecture As hardware is concerned, the CAREU U1 PLUS is comprised of a micro-controller, regulator, GPS receiver, 2G/3G modem, G-Force sensor, flash memory data storage. ● Users can connect PC's Hyper Terminal to the diagnostic setting port for the AVL configuration. ● G-Sensor is for car accident prevention, car tow-away warning and power management. FLASH I/O SENSOR MCU GPS RS232 Powe Modem 1.5 Related Document CAREU U1 PLUS Protocol Document Chapter 2 Taking a Tour of CAREU U1 PLUS 2.1 Dimensions Dimensions (L x W x H): 72mm x 108mm x 31mm 2.2 PIN Assignment 1 3 17 19 21 23 1 3 5 7 9 1 3 5 7 9 11 13 15 2 4 18 20 22 24 2 4 6 8 10 2 4 6 8 10 12 14 16 POWER RS-485 / CAN I/O SERIAL PORT PWR Connector Pin# Signal Name Description IO Electrical Characteristic DC IN Power supply input GND Signal ground Ignition Ignition(ACC) Input DC Vin = +30 ~ +7.5V (Active high) Output1 Open-Collector Imax = 300mA IO Electrical Characteristic VI = DC8 to 30V, Output1 I/O Connector Pin# Signal Name Description Analog Input 2 Analog input 2 DC VIN = +30V ~ 0V Input 4 Positive/ Negative Input 1 Negative Trigger DC VIN = +30V ~ +7.5V (High Active) DC VIN = 0V (Low Active) DC VIN = 0V (Low Active) Input 2 Negative Trigger DC VIN = 0V (Low Active) Analog Input 1 Analog input 1 DC VIN = +30V ~ 0V GND Signal ground Output 2 Open-Collector Imax = 300mA Output 3 Open-Collector Imax = 300mA Output 4 Open-Collector Imax = 300mA 10 Input 3 Positive /Negative DC VIN = +30V ~ +7.5V (High Active) DC VIN = 0V (Low Active) SERIAL Connector Pin# Signal Name Description Supply voltage IO Electrical Characteristic Vo = 5V ( Vout 1~2 Total Imax = 500mA ) Vout1 GND Signal ground TX1 RS232 Data output RX1 RS232 Data input Vout2 GND Signal ground TX2 RS232 Data output RX2 RS232 Data input 1-Wire Vout3 output Supply voltage output 1-Wire Data Vo = 5.0V, (Vout1~2 Total Imax = 500mA) I/O input/output Supply voltage output (BOM optional) Vo = 5.0V, (Vout1~3 Total Imax = 500mA) (BOM Optional) 10 GND Signal ground 11 TX3 RS232 Data output If 1-wire version, this pin unused. 12 RX3 RS232 Data input If 1-wire version, this pin unused. 13 SPK+ Audio output 14 SPK- Audio output 15 MIC+ Microphone Input 16 MIC- Microphone Input 17 RXA RS485 input A 18 RXB RS485 input B 19 TXA RS485 output Z 20 TXB RS485 output Y 21 RS485_GND RS485 ground 22 CANH CAN High 23 CANL CAN Low 24 CAN_GND CAN ground jumper) Full Duplex (*Half Duplex setting by jumper) Full Duplex (*Half Duplex setting by jumper) Full Duplex (*Half Duplex setting by jumper) R_G C_G Full Duplex (*Half Duplex setting by Chapter 3 Getting Started with CAREU U1 PLUS To install the the CAREU U1 PLUS device, follow the instructions below for basic operations 3.1 Device Configuration 1. Connected the serial port 1 to PC COM port 2. In Windows desktop, click Start | All Programs | Accessories | Communications | HyperTerminal. 3. If you are prompted to input the information of your location, complete them to proceed. 4. On the File menu of HyperTerminal, click New Connection. 5. In the Name box, type a name that describes the connection. In the Icon box, click an appropriate icon. Press the OK button to proceed. 6. For Com port properties, configure as follows: Baud Rate --> 115200 bps Data Bits --> 8 Parity --> None Stop Bits --> 1 Flow Control --> None 7. In the connection that you have just set up, click File | Properties. Select the [Connect To] tab. From the [Connect using] drop down list, select the correct com port. 8. In the File menu, click Properties. Click the [Settings] tab. Press the ASCII Setup button. 9. In the [ASCII Sending] group box. Select both Send line ends with line feeds and Echo typed characters locally. Press the OK button. 10.Connect your the CAREU U1 PLUS device and power on,The device startup message will be displayed. 11. In [HyperTerminal] window, type in the command "AT$VERSION?" and press the Enter key. The hardware and firmware version will show. As long as your [HyperTerminal] window appears as the screenshot below, a connection between the device and your system has already been built up and working. It is time to send all configuration commands. 3.2 Communication Settings The CAREU U1 PLUS Vehicle Tracker communicates with your control center by either SMS or 2G/3G (TCP/UDP). Before the device is installed into a vehicle, communication parameters should be set. 1. SMS Configuration Use AT$SMSDST command to set a SMS control center phone number or short code. For example, if the SMS control center phone number is +886123456789, the AT$SMSDST command to be issued into HyperTerminal should be: AT$SMSDST=+886123456789 OK Then you can try to use cellular phone or SMS gateway to send a SMS message to the CAREU U1 PLUS device. Send a SMS message -->"AT$MODID?" Device will response: $MODID=101000001 OK This proves a successful mobile phone SMS connection. 2.WirelessConfiguration Set GPRS servers by using the folloiwng commands: AT$APN=internet,username,password (APN=internet, Username=username, Password=password) OK AT$HOSTS=1,0,60.148.19.10,6000 (Server IP address = 60.148.19.10 and Port number =6000) OK AT$RETRY=5,10 (Message retry settings) OK AT$IPTYPE=1 (Using TCP/IP mode) OK AT$GPRSEN=1 (GPRS enable) OK AT$HB=60,1 (Heartbeat setting) OK Please refer to the CAREU U1 PLUS Protocol Document for more command details. 3.3 GPS Tracking Configurations After the device communication settings are done, the remote GPS tracking is ready to function. The setting of GPS tracking can be done by using AT$PDSR command. For example, AT$PDSR=1,30,0,0,2,0,0,1,0 (Tracking through GPRS by time interval 30 seconds) OK 10 For simple testing GPRS, run the TCP Server U-Series software which is provided by S&T. It is simple server software that can wait for device connection and data. For advanced testing, you need the software Intelli TracerPlus. Please request this software through your sales contact. You can also apply for a testing account from S&T's FleetWeb solution through your sales contact. The main page of the Intelli FleetWeb appears as below: 11 3.4 Firmware Upgrade The firmware of the CAREU U1 PLUS can only be updated through USB interface. With the firmware loader tool provided by S&T, firmware update can be done for the device. Such firmware loader runs on Windows-based systems. To upgrade the firmware, follow the procedure below 1. 2. 3. 4. Connect the device to your PC with the USB cable. Connect the device to power. Power on the device. Run ServerUSeries.exe. A window displays as follows: 12 5. 6. 7. 8. Press browse the button to browse to the firmware provided by S&T. Press the Start button to run the firmware program. After the writing progresses to 100%, it takes about 20 seconds for the update to completes. Firmware update completes. Chapter 4 Technical Specification Hardware Requirements Description CPU 32 bits STM32F2 Series ARM Cortex M3 Internal Memory – 1 Mbyte of Flash memory – 512 bytes of OTP memory – 128 + 4 Kbytes of SRAM External Memory Default 16Mbytes, (512Mbytes for Debug only). GSM GSM Module: Vendor: uBlox SARA-U2 Series Frequency: 850/1900 (U260 for NAR version) 900/1800/2100 (U270 for EUR version) Antenna: External GPS GPS Module: Vendor: uBlox MAX-M8Q/W Sensitivity: -167 dB ( GPS & GLONASS ) -165 dB (GPS & BeiDou ) -166 dB (GPS ) Antenna: External Time to First Fix: 1. Cold Start: 26 Seconds at open sky ( GPS & GLONASS ) 27 Seconds at open sky ( GPS & BeiDou ) 29 Seconds at open sky ( GPS ) 2. Hot Start: 1 Second 3. Aided starts: 2 Seconds at open sky ( GPS & GLONASS ) 3 Seconds at open sky (GPS & BeiDou ) 2 Seconds at open sky (GPS ) I/O(standard) Analog Input x 2 A. Voltage Range: 0-30 V B. Resolution: 12 bit 13 Digital Input x 5: A. 1 High Active( ACC) B. 2 Negative Trigger C. 2 Positive /Negative Digital Output x 4 Sink Current=300mA Maximum Communication Interface RS-232 X 2 (Standard) RS485 X 1 (Full Duplex/ *Half Duplex setting by BOM) CAN X 1 Net Working 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, RMII 1-wire SIM CARD DS2482-100 Battery Life Battery Type SIM Card Access: External Master Battery: N/A Backup Battery: 1150mA Sensor Lithium Ion Built in 6 axis sensor for motion detection AGPS Yes Power Supplies 8-30 VDC 1.B+ 2.GND Temperature Operating: –20 °C to +70 °C(Without Battery) Operating: –20 °C to +60 °C(With Battery) Storage: –20 °C to +70°C Logging 150,000 positions User Report 128 Sets Note: The specification herein is subject to change without prior notice. 14 Systems & Technology Corp. (S&T), founded in 1987, is a market leader in Automatic Vehicle Locating (AVL) solutions, Geographical Information Systems (GIS) and navigation. It has formed a professional development team to innovate the most advanced and comprehensive GPS tracking products for the customers and has built a global service network to provide non-stop services and support. With the well-established marketing networks of over 100 distributors in the world, S&T is your trustworthy tracking solution provider. For more product information, please contact S&T by Email, phone or fax. Web Site http://www.systech.com.tw Email avl@systech.com.tw Phone +886 2 26981599 Fax +886 2 26981211 15 Chapter 5 Regulation Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 16 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Chapter 6 Safety Information 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Mode : UseNone XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2014:12:29 09:48:06+08:00 Modify Date : 2015:01:09 14:54:57+08:00 Metadata Date : 2015:01:09 14:54:57+08:00 Producer : doPDF Ver 7.3 Build 388 (Windows XP Professional Edition (SP 3) - Version: 5.1.2600 (x86)) Format : application/pdf Document ID : uuid:67d1ec96-d6db-4272-bb1f-43c7818e19dd Instance ID : uuid:d2851381-ef82-4ff0-bc19-8574bfb90237 Page Count : 20 Page Layout : OneColumnEXIF Metadata provided by EXIF.tools