Systems and Technology STAVL1515 GPS Vehicle Tracking Device User Manual

Systems & Technology Corp. GPS Vehicle Tracking Device

User Manual

  CAREU U1 PLUS  User Gu   CAREU U1 LITE PLUS User Guide    Version: 0.1 Reference No.: AVL Date: 2015/4/1               SYSTEMS  & TECHNOLOGY COR
  General Information If any breakdown occurs due to the operation of the described product or users’ improper handling in accordance with the instructions of the document, S&T shall be liable for the General Conditions based on the delivery of the described product and the content of the document. This product is not designed for the use of life support appliances, devices or systems and thence a malfunction of the product might reasonably be expected to make personal injury. S&T customers using or selling this product for such applications will take the risk on their own; therefore, it must be agreed S&T will be fully indemnified from any damages due to illegal use or resale. All information in this document is subject to change without notice at any time.   Disclaimer The information, specification, images and photos in this user guide are subject to change without notice and without obligation to notify any person of such revision change.   Copyright This user guide, including all photographs, illustrations and software, to name a few, is protected under international copyright laws, with all rights reserved. This document contains confidential, restricted and proprietary information that it has been exclusively prepared for the internal use of certain designated S&T employees, and may not be duplicated or distributed, in whole or in part, without the prior written consent of S&T’s authorized delegates. Any illegal copying and disclosure of the document are absolutely prohibited, and violators are liable to the damages caused.   © Systems & Technology Corp. All Rights Reserved
   Table of Contents Chapter 1 introduction. ......................................................................................... 1 1.1Features ............................................................................................................ 1 1.2 Scope ................................................................................................................ 1 1.3 Overview .......................................................................................................... 1 1.4 Hardware Architecture .................................................................................... 3 1.5 Related Document ........................................................................................... 3  Chapter 2    Taking a Tour of CAREU U1 LITE PLUS ........................................... 4 2.1 Dimensions ....................................................................................................... 4 2.2 PIN Assignment ................................................................................................ 4  Chapter 3    Getting Started with CAREU U1 LITE PLUS .................................... 5 3.1 Device Configuration ........................................................................................ 5 3.2 Communication Settings .................................................................................. 9 3.3 GPS Tracking Configurations .......................................................................... 10 3.4 Firmware Upgrade ......................................................................................... 11  Chapter 4    Technical Specification ............................................................... 12  Chapter 5    Regulation .................................................................................. 15  Chapter 6    Safety Information ..................................................................... 16
 1   Chapter 1 introduction. Designed with the latest GPS technology, the CAREU U1 LITE PLUS delivers positioning message by wireless transmission to GIS platform, and then helps back-end users proceed with the analysis and the applications of vehicle transport, management, anti-theft, security and tracking.  A microcontroller can probe location and command data at regular intervals, derive actions from location, peripheral and control data, and execute such actions.     Peripheral data indicates the status of various peripherals connected to and/or controlled by the device. Among the best features of the CAREU U1 LITE PLUS Vehicle Tracker, in particular, they transmit data in ASCII mode (Intellitrac X Series compatible mode) or binary mode. 1.1 Features ●      SMS,GPRS/UMTS/HSPA TCP/UDP, USSD, FTP                                                                           ●      Real-time tracking (Time, Distance Interval or Intelligent Mode, and Heading) ●      Firmware upgrade over the air ( form FTP) ●      Journey report wireless download ●      Battery low alert ●      Geofence reports ●      Mileage reports ●      User-defined reports ●      6-Axis Sensor ●      NMEA-0183 Output for Navigation   ●      GPS Antenna Destroyed Alarm ●      CAN BUS interface (optional) 1.2 Scope This document will guides you to start the CAREU U1 LITE PLUS Vehicle Tracker. However,as this document contains basic device configuration only, please see the CAREU U1 LITE PLUS Protocol Document for the advanced information. 1.3 Overview Device Overview
 2      1.      GPS LED 2.      GSM LED 3.      Power & I/O Connector 4.      RS-232/CAN Connector 5.      USB Connector 6.      GPS Antenna Connector 7.      Reset Switch 6.      Speaker/MIC Connector 2 1 3  4  5 6 7 8
 3  1.4 Hardware Architecture As hardware is concerned, the CAREU U1 LITE PLUS is comprised of a micro-controller, regulator, GPS receiver, 2G/3G modem, G-Force sensor, flash memory data storage.  ●      Users can connect PC's Hyper Terminal to the diagnostic setting port for the AVL configuration.  ●  G-Sensor is for car accident prevention, car tow-away warning and power management.      FLASH  I/O     SENSOR     MCU   GPS  RS232     Powe    Modem      1.5 Related Document   CAREU U1 LITE PLUS Protocol Document
 4  Chapter 2    Taking a Tour of CAREU U1 LITE PLUS 2.1 Dimensions  Dimensions (L x W x H): 105.5mm x 72mm x 28.5mm  2.2 PIN Assignment    PWR/IO Connector Pin# Signal Name  Description  IO  Electrical Characteristic 1  DC IN  Power supply input  I  DCIN = DC 8V to 30V, 2  GND  Signal ground  G   3  Ignition  Ignition(ACC) Input  I  DC Vin = +30 ~ +7.5V (Active high) 4  Output1  Open-Drain output  O  Imax = 750mA 5  Output2  Open-Drain output  O  Imax = 750mA 6  Input 1  Negative Trigger    I   Low Active 7  Input 2  Positive Trigger    I    High Active 8  Input 3  Negative Trigger    I   Low Active 9  1-Wire  1-Wire Data  I/O   10  Analog Input1  Analog Input1  I  Voltage Range DC 0~+30V
 5  Serial/CAN Connector Pin# Signal Name  Description  IO  Electrical Characteristic 1  RS232-TX  RS232 Data output  O   2  RS232RX  RS232 Data Input  I   3  Vout  Supply voltage output O  Vo = 5V ( Vout Total Imax = 500mA ) 4  GND  Ground  G   5  CAN_H  CAN_H  I/O   6  CAN_L  CAN_L  I/O    MIC/SPK Connector Pin# Signal Name  Description  IO  Electrical Characteristic 1  MIC+  Microphone Input  I   2  MIC-  Microphone Input  I   3  SPK+  Audio output  O   4  SPK-  Audio output  O    Chapter 3    Getting Started with CAREU U1 LITE PLUS  To install the the CAREU U1 LITE PLUS device, follow the instructions below for basic operations 3.1 Device Configuration  1. Connected the serial port 1 to PC COM port    2. In Windows    desktop, click Start | All Programs | Accessories | Communications | HyperTerminal.  3. If you are prompted to input the information of your location, complete them to proceed.  4. On the File menu of HyperTerminal, click New Connection.  5. In the Name box, type a name that describes the connection. In the Icon box, click an appropriate icon. Press the OK button to proceed.
 6    6. For Com port properties, configure as follows: Baud Rate --> 115200 bps Data Bits --> 8 Parity --> None Stop Bits --> 1 Flow Control --> None  7. In the connection that you have just set up, click File | Properties. Select the [Connect To] tab. From the [Connect using] drop down list, select the correct com port.
 7   8. In the File menu, click Properties. Click the [Settings] tab. Press the ASCII Setup button.    9. In the [ASCII Sending] group box. Select both Send line ends with line feeds and Echo typed characters locally. Press the OK button.  10.Connect your the CAREU U1 LITE PLUS device and power on,The device startup message will be displayed.
 8    11. In [HyperTerminal] window, type in the command "AT$VERSION?" and press the Enter key. The hardware and firmware version will show. As long as your [HyperTerminal]    window appears as the screenshot below, a connection between the device and your system has already been built up and working. It is time to send all configuration commands.
 9  3.2 Communication Settings  The CAREU U1 LITE PLUS Vehicle Tracker communicates with your control center by either SMS or 2G/3G (TCP/UDP). Before the device is installed into a vehicle, communication parameters should be set.  1. SMS Configuration Use AT$SMSDST command to set a SMS control center phone number or short code. For example, if the SMS control center phone number is +886123456789, the AT$SMSDST command to be issued into HyperTerminal should be:  AT$SMSDST=+886123456789  OK  Then you can try to use cellular phone or SMS gateway to send a SMS message to the CAREU U1 LITE PLUS device. Send a SMS message -->"AT$MODID?" Device will response: $MODID=101000001  OK  This proves a successful mobile phone SMS connection.    2.WirelessConfiguration   Set GPRS servers by using the folloiwng commands: AT$APN=internet,username,password (APN=internet, Username=username, Password=password) OK AT$HOSTS=1,0,60.148.19.10,6000  (Server IP address = 60.148.19.10 and Port number =6000) OK AT$RETRY=5,10 (Message retry settings) OK AT$IPTYPE=1 (Using TCP/IP mode) OK AT$GPRSEN=1 (GPRS enable) OK
 10  AT$HB=60,1 (Heartbeat setting) OK  Please refer to the CAREU U1 LITE PLUS Protocol Document for more command details.  3.3 GPS Tracking Configurations  After the device communication settings are done, the remote GPS tracking is ready to function. The setting of GPS tracking can be done by using AT$PDSR command. For example, AT$PDSR=1,30,0,0,2,0,0,1,0 (Tracking through GPRS by time interval 30 seconds) OK   For simple testing GPRS, run the TCP Server U-Series software which is provided by S&T. It is simple server software that can wait for device connection and data.   For advanced testing, you need the software Intelli TracerPlus. Please request this software through your sales contact.
 11    You can also apply for a testing account from S&T's FleetWeb solution through your sales contact.   The main page of the Intelli FleetWeb appears as below:                 3.4 Firmware Upgrade The firmware of the CAREU U1 LITE PLUS can only be updated through USB interface. With the firmware loader tool provided by S&T, firmware update can be done for
 12  the device. Such firmware loader runs on Windows-based systems. To upgrade the firmware, follow the procedure below  1.    Connect the device to your PC with the USB cable. 2.    Connect the device to power. 3.    Power on the device. 4.    Run ServerUSeries.exe. A window displays as follows:     5.  Press browse the button to browse to the firmware provided by S&T. 6.  Press the Start button to run the firmware program. 7.  After the writing progresses to 100%, it takes about 20 seconds for the update                       to completes. 8.  Firmware update completes. Chapter 4    Technical Specification Hardware Requirements Description CPU    STM32F103RCT6 (ARM Cotex-M3) 72MHz STM32F105RCT6 (ARM Cotex-M3) 72MHz/CAN Version Internal Memory  256Kbyte Flash/48Kbyte RAM External Memory  Default 8Mbytes, (512Mbytes for Debug only). Cellullar  Cellullar Module:  Vendor: uBlox SARA-G350(2G) / SARA-U2(3G)  Frequency: 850/900/1800/1900/2100 MHZ
 13   Antenna: Internal GPS  GPS Module:  Vendor: uBlox MAX-M8Q/W  Sensitivity:    -167 dB    ( GPS & GLONASS )   -165 dB    (GPS & BeiDou )                 -166 dB    (GPS )  Antenna: External Time to First Fix: 1.        Cold Start: 26 Seconds at open sky ( GPS & GLONASS )                   27 Seconds at open sky ( GPS & BeiDou )                   29 Seconds at open sky ( GPS    ) 2.        Hot Start: 1 Second 3.        Aided starts: 2 Seconds at open sky ( GPS & GLONASS )                       3 Seconds at open sky (GPS & BeiDou )                       2 Seconds at open sky (GPS    ) I/O(standard)   Analog Input x 1   A. Voltage Range: 0-30 V B. Resolution: 12 bit  Digital Input x 4:   A. 1 Postive Active( ACC) B. 2 Negative Trigger C. 1 Positive  Digital Output x 2 Sink Current=750mA Maximum Communication Interface RS-232 X 1 USB2.0 Full Speed CAN interface X 1 (Must to replace STM32F105xxx MCU ) 1-wire  DS2482-100 Main power Remove detect Yes GPS open/short detect Yes SIM CARD                    SIM Card Access: External Battery Life  Backup Battery: 950mA Battery Type  Lithium Ion Sensor   3 axis sensor for motion detection  6 axis (optional) AGPS  Yes
 14  Temperature  Operating: –20 °C to +60 °C(With Battery) Operating: –20 °C to +70 °C(Without Battery) Storage: –20 °C to +80°C Logging  TBD    positions User Report  TBD    Sets Note: The specification herein is subject to change without prior notice.           Systems & Technology Corp. (S&T), founded in 1987, is a market leader in Automatic Vehicle Locating (AVL) solutions, Geographical Information Systems (GIS) and navigation. It has formed a professional development team to innovate the most advanced and comprehensive GPS tracking products for the customers and has built a global service network to provide non-stop services and support.   With the well-established marketing networks of over 100 distributors in the world, S&T is your trustworthy tracking solution provider. For more product information, please contact S&T by Email, phone or fax.     Web Site  http://www.systech.com.tw  Email  avl@systech.com.tw  Phone  +886 2 26981599  Fax  +886 2 26981211
 15  Chapter 5    Regulation  Federal Communication Commission Interference Statement  This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received,  including  interference  that  may cause undesired operation.  This equipment has been  tested  and  found  to  comply  with the limits for  a  Class  B digital device, pursuant  to  Part 15 of  the  FCC  Rules.    These  limits  are designed to provide  reasonable  protection  against  harmful  interference  in  a  residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference  to  radio  communications.    However,  there  is  no  guarantee  that interference will not occur in a particular installation.    If this equipment does cause harmful  interference  to radio  or  television  reception,  which  can  be  determined  by turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the interference by one of the following measures:   Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution:  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This  transmitter  must  not  be co-located  or  operating  in conjunction  with  any other antenna or transmitter.
 16  Radiation Exposure Statement: This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an uncontrolled  environment.  This  equipment  should  be  installed  and  operated  with minimum distance 20cm between the radiator & your body.   Chapter 6    Safety Information

Navigation menu