TAIDOC TECHNOLOGY 9030A01 TD-9030A User Manual Attachment 3

Download:
Mirror Download [FCC.gov]
Document ID	2328503
Application ID	8WQylRf0xyPQOEzmUY+aVQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.23kB (252908 bits)
Date Submitted	2014-07-18 00:00:00
Date Available	2014-07-18 00:00:00
Creation Date	2014-07-17 18:04:56
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2014-07-17 18:04:59
Document Title	Attachment 3
Document Creator	Acrobat PDFMaker 9.1 Word 版
Document Author:	kolinda

User Manual
TD-9030A
Brand Name: TaiDoc
FCC ID: TM79030A01
Version 1.0
2014-07
A1.0 - 1 of 7
Description:
The TD-9030A is a low power and low costs Bluetooth 4.0 BLE module based
on the 32 bit ARMR Cortex™-M0 CPU .Perfect for communication and cable
replacement between your device and a smartphone, computer or other
devices. It is easy to setup and use thanks to real and virtual UART interface
and AT commands.
Key Features




2.4 GHz transceiver
 -93 dBm sensitivity in Bluetooth® low energy mode
 250 kbps, 1 Mbps, 2 Mbps supported data rates
 TX Power -20 to +4 dBm in 4 dB steps
 TX Power -30 dBm Whisper mode
 13 mA peak RX, 10.5 mA peak TX (0 dBm)
 RSSI (1 dB resolution)
ARM® Cortex™-M0 32 bit processor
 275 μA/MHz running from flash memory
 150 μA/MHz running from RAM
Memory
 256 kB or128 kB embedded flash program
 memory
 16 kB RAM
UART (CTS/RTS)
Applications

Medical devices
 BGM
 BPM
A1.0 - 2 of 7
1. Pinout and Terminal Description
Figure 1: Pinout
Pin
Symbol
I/O Type
Description
BAT_Monitor
Battery Voltage Monitor
VBAT
Power input
VBAT
Power input
VCC
Power Output
VCC
Power Output
VCC
Power Output
NC
NC
Not Connect
DEV_STAT
Wakeup Device
PIO-0
I/O
GPIO
10
PIO-1
I/O
GPIO
11
DTM_RTS
UART RTS signal (Note.1)
12
DTM_CTS
UART CTS signal (Note.1)
13
DTM_TX
UART TX signal (Note.1)
14
DTM_RX
UART RX signal (Note. 1)
15
GND
GND
A2.1 - 3 of 7
16
GND
GND
17
SWDCLK
JTACK Clock
18
SWDIO
I/O
JTACK Data
19
DTM_Mode
Set Low to DTM Mode
Set High to BLE Mode
20
NC
NC
Not Connect
21
BLE_RX
UART RX
22
BLE_TX
UART TX
23
BLE_CTS
UART CTS
24
BLE_RTS
UART RTS
25
NC
NC
Not Connect
26
Paring_Key
Set Low to Paring Device
27
NC
NC
Not Connect
28
LED
LED indicator
29
GND
GND
30
NC
NC
Note.1 DTM is Direct Test Mode。
Not Connect
2. Power supply
The Module accept 3.1V to 4.2V DC voltage input，Power supply should
guarantee good ripple suppression and enough current.
3. Antenna
The module integrates a chip antenna so there’s no need to use antenna on
customer’s PCB.
4. UART interface
This is a standard UART interface for communicating with other serial devices.
The UART interface provides a simple mechanism for communicating with
other serial devices using the RS232 protocol.
The UART CTS and RTS signals can be used to implement RS232 hardware
flow control where both are active low indicators.
Default parameter set is 19200,8,n,1
A2.1 - 4 of 7
5. Dimension
A2.1 - 5 of 7
FEDERAL COMMUNICATIONS COMMISION (FCC) STATEMENT
15.21
You are cautioned that changes or modifications not expressly approved
by the part responsible for compliance could void the user’s authority to
operate the equipment.
15.105(b)
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1) This device may not cause harmful interference and
2) This device must accept any interference received, including interference
that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
1. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance.
A2.1 - 6 of 7
根據 NCC 低功率電波輻射性電機管理辦法 規定:
經型式認證合格之低功率射頻電機，非經許可，公司、商號或
第十二條
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經
發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續
第十四條
使用。前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾。
A2.1 - 7 of 7

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : kolinda
Create Date                     : 2014:07:17 18:04:56+08:00
Modify Date                     : 2014:07:17 18:04:59+08:00
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2014:07:17 18:04:59+08:00
Creator Tool                    : Acrobat PDFMaker 9.1 Word 版
Document ID                     : uuid:2c73aa51-89c6-4f54-907c-3bcdd0505a4e
Instance ID                     : uuid:4489da2a-944e-463a-a027-924aa8ff60e3
Format                          : application/pdf
Title                           : Attachment 3
Description                     : 
Creator                         : kolinda
Producer                        : Adobe PDF Library 9.0
Keywords                        : 
Source Modified                 : D:20140711085818
Company                         : 
Page Layout                     : OneColumn
Page Count                      : 7

EXIF Metadata provided by EXIF.tools