TCL Communication B072 MOVETIME Track & Talk watch User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3064959
Application ID	Kf251dMRklC+MfX4hLuD+Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	149.3kB (1866243 bits)
Date Submitted	2016-07-15 00:00:00
Date Available	2017-01-12 00:00:00
Creation Date	2016-07-12 17:15:45
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2016-07-12 17:15:50
Document Title	Users Manual
Document Creator	Adobe InDesign CS6 (Windows)

MOVETIME
Track&Talk watch
Quick Start Guide
CJB1F61ALAAA
Know your watch
Overview
Front
Back
A Watch-button
B Speaker
C Volume +
On the Home screen: Press to open the
phonebook, press again to choose contacts.
In the List mode: Press to increase the volume
or page up.
D Volume -
On the Home screen: Press to enter the voice
messages list.
In the List mode: Press to decrease the volume
or page down.
When you have an incoming voice call, short
press to answer.
Press for 3 seconds to start recording.
E SOS key
Emergency calls: Long press the ‘SOS’ key for at
least 3 seconds.
F Power key
•
•
•
•
•
•
Power on/off.
Enter into the volume list.
When you have an incoming call, short press
to reject the call.
On the Home screen, short press to enter
the volume mode.
On all screens other than Home, short press
once to go back.
Depress the button for at least 8 seconds to
initiate a system reboot.
G Microphone
H Wristband
SIM slot
Charging port
Notes:
• The screen will light up by pressing any key.
• Watch only supports GPRS network and Nano SIM card without
encrypting PIN code.
Screen
Steps
G: GPRS
R: Roaming
Battery power
Signal strength
Time
Voice SMS tips
Date
When the watch is roaming, the right side of the signal bar will appear
“R”. At the same time, prompt information will display in the message
bar in the application. Note: Consult the local operators to open the
roaming service.
Inserting Nano SIM card
Basic operations on your watch
Power on/off
Press and hold the Power key for 3 seconds to power on/off your
watch.
Press and hold the Power key for 8 seconds to reboot when your
watch crashes.
SOS
Press and hold the SOS key for 3 seconds on any screen (except the
incoming/ongoing/dialing call screen) to call five key family members.
1. Once your watch has obtained a fix on your location, it will
send details of your location to 10 chosen family members.
(Application shows the SOS alarm screen with prompt).
2. It will attempt to dial 10 chosen numbers in turn. If there is no
answer within 10 seconds, it will move onto the next number in
the list until a call successfully connects.
3. If a SIM card is not inserted, or if the watch does not have a
signal, the SOS feature will instead attempt to dial 112
(Emergency services). You can press the Power Key at any time
to either cancel the call setup or hang up the call. Note: Currently
emergent number is not set by default, you can customize it.
Note: Press the Power key to interrupt the call.
Sending a voice message
1. Press Volume - for 3 seconds to start recording.
2. Release to stop recording, as well as to send the voice message.
3. When finishes sending, it will go back to the last screen.
Note: Notification icon will flash when your watch receives a voice
message.
Voice message management
• Press Volume + to scroll up the menu.
• Press Volume - to scroll down the menu.
• Short press the Power key to go back to the Home screen.
Note: The storage is limited to 30 voice messages. If there are more
than 30 messages, the message will be overwritten automatically.
Calling and answering
1. Short press Volume + to enter the family number list.
2. Short press Volume + to choose the next family number.
3. Press Volume - for 3 seconds to send a voice message to chosen
family number.
Note: Press the Power key to go back to the Home screen.
Volume adjustment
• Short press power on/off button first, then press Volume + to
increase the volume.
• Short press power on/off button first, then press Volume - to
decrease the volume.
Note: Decrease the volume to mute your watch. When you have an
incoming call, your watch will vibrate.
Power off & Airplane mode
Long press the Power key for 3 seconds to enter “Power off &
Airplane mode” screen.
Update
Watch will install the firmware automatically after finishing
downloading.
Using the application from your
smartphone
Download the application from App Store or Google play.
Pairing
Input the IMEI to pair your watch
Obtain the information of IMEI number through the package
information or pressing Volume +/- and the SOS key in the same
time until the information displayed on the screen. Then input the
IMEI number to the application information bar and confirm.
Input IMEI
and press
Confirm.
The server will send a random code to your watch and the information
displayed on the screen should be noted at this time. Input the
random code to the application information bar and confirm.
Scan the QR code to pair your watch
You can share the QR code to add some group members. Scanning
the QR code will be automatically adjusted according to the interval
time.
Functions
Application screen
Slide left
to find
the list
Hide or show the shortcut menu.
Click to refresh the watch location instantly.
Click to enter the details page of Electronic fence.
Click to jump to the navigation page.
Steps.
Power.
Click to enter the voice message screen.
Click to dial by the watch.
Member management
Touch Family numbers to open the member list.
Set the local emergency call number here.
Note: Each device will have only one administrator, and the user will
be regarded as an administrator for the first time.
Administrator can transfer the management rights in the members’
management page.
Voice message
to enter the voice screen.
Touch
When you create a voice message, the length of each recording is
15s. You can dialogue with some group members, or dialogue with
your children alone.
10
Safe zone
Touch
to enter the Safe zone screen.
In this function, you can set an area on the map as a safe area for your
child. When your child leaves the security area, you will be notified.
Pay attention that the timeliness of the notification will depend on
the frequency of the location. The longer interval time for positioning
that you set, the time to receive the notification will be relatively
longer.
Save power
Touch
to enter the power screen.
You can choose the location frequency according to the daily usage
habit. Different positioning mode will affect the positioning accuracy
and standby time. Choose the appropriate use mode according to
the actual scene.
11
Mute time
Touch Mute time to set the reminder function of your watch.
You can set to mute or cancel the vibration according to the actual
environment in use by your children. Pay attention that in the silent
mode, children can recover the setting by adjusting the volume of the
watch. But in the vibration mode, it need to be recovered through
application setting.
Upgrade
Touch Update to upgrade your watch and App.
The status bar at the bottom will display the related downloading
progress when upgrading. Be aware that the watch relies on the
network when upgrading. It will use a certain amount of data.
12
FAQ
1. Unable to obtain the position of your watch
Go to check if your watch has a SIM card or if you’re in a place where
can’t receive the signal. If SIM was inserted with device already
powered on, it will not register as this device does not support “hot
swap”. In this case user will need to restart (power off/on device) to
restore service.
2. Unable to obtain the verification code
You need to open the relevant SMS receiving service. For more
information, consult your local operators.
3. Waterproof notice
This product has an IP65 rating which means it is protected against
water jets. Do not submerge your watch in water, for example when
swimming.
4. Positioning accuracy
Your watch will provide three kinds of positioning modes: GPS,
Wi‑Fi, LBS. Position accuracy will be different according to different
positioning methods. All position information is only for reference in
a certain range.
5. Data service
The position information of watch and remote setting caused by voice
message and application will be working based on the communication
between GPRS network and cloud server. It will consume the data
which need to be paid by yourself.
6. SOS
The guardian should be familiar with the specific operation of SOS
and the operation instruction for children.
7. Whether the material of this product is harmful to children
The material in use has passed related safety testing for children,
which can ensure the safety of daily use.
8. Charging
When the charging port is corroded or dirty, it will seriously affect the
charging process which requires a clean surface. After playing sports,
wipe any sweat from your watch before charging.
13
9. Storage and use of location data for user
For all the data related to you, we will only use the queries you submit
to us. We will not use for any commercial application or development
without authorisation.
www.sar-tick.com
This product meets applicable national SAR limits of 4W/kg.
The specific maximum SAR values can be found in the section of this
user guide.
When carrying the product or using it while worn on your body, either
use an approved accessory such as a holster or otherwise maintain
a distance of 0 mm from the body to ensure compliance with RF
exposure requirements. Note that the product may be transmitting
even if you are not making a phone call.
Certification
WEEE Approval
This device is in compliance with the essential requirements and
other relevant provisions of the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE Directive).
This symbol on device means that these products must
be taken to collection points at the end of their life:
- Municipal waste disposal centres with specific bins for
these items of equipment.
- Collection bins at points of sale.
They will then be recycled, preventing substances being disposed of
in the environment, so that their components can be reused.
In European Union countries:
These collection points are accessible free of charge.
All products with this sign must be brought to these collection points.
In non European Union jurisdictions:
Items of equipment with this symbol are not to be thrown into
ordinary bins if your jurisdiction or your region has suitable recycling
14
and collection facilities; instead they are to be taken to collection
points for them to be recycled.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCRDING TO
THE INSTRUCTIONS
Following air regulation, the battery of your product is not charged.
Please charge it first.
RoHs Approval
This device is in compliance with the restriction of the use of
certain hazardous substances in electrical and electronic equipment
Directive 2011/65/EU (RoHs Directive).
CHARGERS
Chargers will operate within the temperature range of: 0°C to 40°C.
The chargers designed for your device meet with the standard for
safety of information technology equipment and office equipment
use. They are also compliant to the eco design directive 2009/125/
EC. Due to different applicable electrical specifications, a charger you
purchased in one jurisdiction may not work in another jurisdiction.
They should be used for this purpose only.
The charger shall be installed near the device and shall be easily
accessible.
Federal Communications Commission (FCC) Declaration of
Conformity
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
15
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
FCC RF Exposure Information (SAR):
This device is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the United States.
During SAR testing, this is set to transmit at its highest certified
power level in all tested frequency bands, and placed in positions that
simulate RF exposure in usage near the body with the separation of
0 mm. Although the SAR is determined at the highest certified power
level, the actual SAR level of the device while operating can be well
below the maximum value. This is because the device is designed to
operate at multiple power levels so as to use only the power required
to reach the network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
The exposure standard for wireless devices employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is 4W/kg.
Tests for SAR are conducted using standard operating positions
accepted by the FCC with the device transmitting at its highest
certified power level in all tested frequency bands.
The FCC has granted an Equipment Authorization for this model
device with all reported SAR levels evaluated as in compliance with
the FCC RF exposure guidelines. SAR information on this model
device is on file with the FCC and can be found under the Display
Grant section of HYPERLINK “http://www.fcc.gov/oet/ea/fccid”
www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2ACCJB072.
For this device, the highest reported SAR value for usage near the
body is:
Maximum SAR for this model and conditions under which it was
recorded.
Body-worn SAR
GSM 1900
16
2.57 W/kg
SAR compliance for body operation is based on a separation distance
of 0 cm between the device and the human body. During use, the
actual SAR values for this device are usually well below the values
stated above. This is because, for purposes of system efficiency and
to minimize interference on the network, the operating power of your
device is automatically decreased when full power is not needed. The
lower the power output of the device, the lower its SAR value.
Body-worn SAR testing has been carried out at a separation
distance of 0 cm. To meet RF exposure guidelines during body-worn
operation, the device should be positioned at least this distance away
from the body.
If you are not using an approved accessory ensure that whatever
product is used is free of any metal and that it positions the device
the indicated distance away from the body.
Organizations such as the World Health Organization and the US
Food and Drug Administration have suggested that if people are
concerned and want to reduce their exposure they could use a handsfree accessory to keep the wireless device away from the head or
body during use, or reduce the amount of time spent on the device.
For more information you can go to www.alcatel-mobile.com;
Additional information about electromagnetic fields and public health
are available on the following site: http://www.who.int/peh-emf
This device is equipped with a built-in antenna. For optimal operation,
you should avoid touching it or degrading it.
Licenses
This equipment is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC. The entire copy
of the Declaration of Conformity for your device can be obtained
through our Website: www.alcatel-mobile.com
Warranty
The device is warranted against any deviation from technical
specifications for a period of twelve (12) (1) months from the date
specified on your original invoice.
(1)
The warranty period may vary depending on your country.
17
Under the terms of this warranty, you must immediately inform your
vendor in case of a conformity defect on this device, and present a
proof of purchase.
The vendor or repair center will decide whether to replace or repair
this device, as appropriate.
Repaired or replaced this device is warranted ONE (1) month unless
there are statutory provisions to the contrary.
This warranty shall not apply to damage or defects to this device
due to:
1) Not following the instructions for use or installation,
2) Not being compliant with technical and safety standards
applicable in the geographical area where this device is used,
3) Improper maintenance of sources of energy, and of the overall
electric installation,
4) Accidents or consequences of theft of the vehicle in which this
device is transported, acts of vandalism, lightning, fire, humidity,
infiltration of liquids, inclement weather,
5) Connecting to or integrating into this device any equipment not
supplied or not recommended by the manufacturer,
6) Any servicing, modification or repair performed by individuals
not authorised by the manufacturer, the vendor or the approved
maintenance centre,
7) Use of this device for a purpose other than that for which it
was designed,
8) Malfunctions caused by external causes (e.g., radio interference
from other equipment, power voltage fluctuations),
9) Faulty connections resulting from unsatisfactory radio
transmission or caused by the absence of radio relay coverage.
Warranty is also excluded for this device on which markings or serial
numbers have been removed or altered.
This device is also warranted against hidden defects (defects inherent
in the design, manufacture, etc.).
There are no other express warranties than this printed limited
warranty, expressed or implied, of any nature whatsoever.
In no event shall the manufacturer be liable for incidental or
consequential damages of any nature whatsoever, including but
not limited to trading loss, commercial loss, to the full extent those
damages can be disclaimed by law. Some countries/states do not
allow the exclusion or limitation of incidental or consequential
damages, or limitation of the duration of implied warranties, so the
preceding limitations or exclusions may not apply to you.
18

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2016:07:12 17:15:45+08:00
Metadata Date                   : 2016:07:12 17:15:50+08:00
Modify Date                     : 2016:07:12 17:15:50+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:c645c9be-3788-4455-9a4f-ca8f70140ad9
Original Document ID            : xmp.did:BC91BB09EFD5E511BD9096FCF42A41D2
Document ID                     : xmp.id:AA6847301148E611AAB4B05F3C94814D
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:A96847301148E611AAB4B05F3C94814D
Derived From Document ID        : xmp.did:36C6454A4347E6118B1BAA84712685F7
Derived From Original Document ID: xmp.did:BC91BB09EFD5E511BD9096FCF42A41D2
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2016:07:12 17:15:45+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 18
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools