TCL Delonghi Home Appliances 5005HBS 802.11 b/g/n Wifi module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2934057
Application ID	vrrE2mfAAA9hxKXO32fnXw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	42.83kB (535397 bits)
Date Submitted	2016-03-17 00:00:00
Date Available	2016-09-13 00:00:00
Creation Date	2016-03-11 10:21:09
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2016-03-11 10:21:09
Document Title	User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Jumy

BroadLink 5005-HBS Wi-Fi Module
Datasheet
1. Introduction
1.1 Overview
The 5005-HBS is a highly integrated Wi-Fi module, which supportsIEEE802.11b/g/n single stream,
providing GPIO for intelligent control, and UART interfaces for device communication.
The 5005-HBS has 8Mbits flash and integrates power amplifier, low noise amplifier, and RF switch to
reduce the module size and RF design capability required.
The 5005-HBS embedded ARM Cortex-M4F MCU, the Frequency could reach 200MHz, 512KB SRAM
and 8Mbits Flash are included.
5005-HBS block diagram
1.2 Applications




Smart home appliances
Remote Control
Medical/Health Care
Network consumer devices
1.3 Key Features


Single operation voltage: 5V
Power consumption: 80mA for IDLE mode and 1.1mA for Sleep mode
Wi-Fi connectivity








802.11b, 802.11g, 802.11n (single stream) on channel 1-11@2.4GHz
WPA/WPA2 Enterprise
Transmit power: 16dBm@11b, 14dBm@11g,13dBm@11n
Receiver Sensitivity: <-78dBm (802.11b 11Mbs),<-68 dBm (802.11g 54Mbs), <-66dBm
(802.11n MCS7)
Max Data rate: 11Mbps@11b，54Mbps@11g, MCS7@11n HT20
Wi-Fi modes: Station and AP
Patent SmartConfig™ technology

On-board PCB antenna, IPEX connector for external antenna

Operating Temperature: -10 ℃ to 70 ℃
1.4 Channels
802.11b, 802.11g, 802.11n(20MHz): 11
Working Frequency of Each Channel:
channel
Frequency
channel
Frequency
2412
2442
2417
2447
2422
2452
2427
10
2457
2432
11
2462
2437

2. Product Overview
2.1 Product Picture
2.2 Block Diagram
3. Electrical Characteristics
3.1 WLAN Parameter
Frequency Range
Wireless Standard
Output Power
Antenna
Input Level Sensitivity
Protocol Stack
Data Rate
Security
Network Type
2.412 GHz ‐ 2.462 GHz
IEEE 802.11 b/g/n
802.11b:16dBm
802.11g:15dBm
802.11n:15dBm
PCB printed ANT
IPEX connector for external antenna
802.11b<‐90dBm@1Mbps
802.11b<‐80dBm@11Mbps
802.11g<‐88dBm@6Mbps
802.11g<‐70dBm@54Mbps
IPv4, TCP/UDP/FTP/HTTP/HTTPS/TLS/mDNS
11M@802.11b, 54M@802.11g, MCS7@802.11n
data encryption standard：WEP/WEPA/WPA2
encryption algorithm：WEP64/WEP128/TKIP/AES
STA/AP/STA+AP/WIFI Direct
3.2
Absolute Maximum Ratings
Symbol
Ts
TA
Description
Min.
Storage temperature
‐40
Ambient
operating ‐20
Max.
125
85
Units
℃
℃
temperature
3.3
DC Voltage and Current
Specifications
VDD
VIL(input low voltage)
VIH(input high voltage)
VOL(output low voltage)
VOH(output high voltage)
Standby
pulse current @TX
11b @16dBm 11Mbps
Min.
Typ.
4.5
‐0.4
0.7*VDD
‐0.4
0.7*VDD
60
350
pulse current @TX
11g @14dBm 54Mbps
3.4
Max.
5.5
0.7
VDD+0.4
0.3*VDD
VDD+0.4
350
Units
mA
mA
mA
IEEE802.11b Mode
ITEM
Modulation Type
Frequency range
Specification
DSSS / CCK
2412MHz~2462MHz
Channel
CH1 to CH11
Data rate
1, 2, 5.5, 11Mbps
TX Characteristics
Min
Typical
Max.
Unit
Transmitter Output Power
16
11bTarget Power
Frequency Error
‐20
dBm
+20
Constellation Error( peak EVM)@ target power
1~11Mbps
‐28
‐26
ppm
RX Characteristics
Min
Typical
Max.
Unit
Minimum Input Level Sensitivity
1Mbps (FER≦8%)
‐95
dBm
11Mbps (FER≦8%)
‐84
dBm
Maximum Input Level
‐10
dBm
(FER≦8%)
3.5
IEEE802.11g Mode
ITEM
Specification
Modulation Type
OFDM
2412MHz~2462MHz
Frequency range
CH1 to CH11
Channel
6, 9, 12, 18, 24, 36, 48, 54Mbps
Data rate
TX Characteristics
Min
Typical
Max.
Unit
Transmitter Output Power
14
11gTarget Power
+20
ppm
6Mbps
‐21
dB
54Mbps
‐31
dB
@11MHz
‐20
dBr
@20MHz
‐28
dBr
@30MHz
‐40
dBr
Max.
Unit
Frequency Error
‐20
dBm
Constellation Error( peak EVM)@ target power
Transmit spectrum mask
RX Characteristics
Min
Typical
Minimum Input Level Sensitivity
6Mbps
‐90
54Mbps
‐72
Maximum Input Level
(FER≦10%)
‐20
dBm
dBm
dBm
3.6
IEEE802.11n 20MHz Bandwidth Mode
ITEM
Specification
Modulation Type
OFDM
2412MHz~2462MHz
Frequency range
CH1 to CH11
Channel
MCS0/1/2/3/4/5/6/7
Data rate
TX Characteristics
Min
Typical
Max.
Unit
Transmitter Output Power
13
11n HT20 Target Power
+20
ppm
‐19
dB
‐30
dB
@11MHz
‐20
dBr
@20MHz
‐28
dBr
@30MHz
‐40
dBr
Max.
Unit
Frequency Error
‐20
dBm
Constellation Error( peak EVM)@ target power
MCS0
MCS7
Transmit spectrum mask
RX Characteristics
Min
Typical
Minimum Input Level Sensitivity
MCS0
‐90
MCS7
‐72
Maximum Input Level
(FER≦10%)
‐20
dBm
dBm
dBm
4. Mechanical Characteristics
5005-HBS has 4 pins. The layout of PINs is shown in the figure below.
4.1
PIN Definitions
Pins
Pin Assignment
Notes
Pin1
VCC
5V
Pin2
GND
Ground
Pin3
UART_TX_5V
Pin4
UART_RX_5V
UART
transmitter Pin
UART Receiver
Pin
1.
2.
3.
4.
TX and RX of UART0 are used to communicate with peripheral processor using power source
of 5V. Its output voltage level refers to the description in chapter 3.3 DC characteristics。
The 5005-HBS contains RC (resistance- capacitance) and WATCHDOG. Users also can use
their RESET circuit.
The WIFI indicator LED is embedded in the module.
Press the reset button for more than 5 seconds, the module would be resettled,
4.2
Printed Antenna
The 5005-HBS supports on-board PCB printed antenna. When the Operating Frequency is between
2.4G~2.5GH, S11 of antenna port is less than-10dB and peak gain is about 2.2dBi.
Antenna radiation pattern simulation
Antenna port S11 simulation curve
When integrating the Wi-Fi module with on board PCB printed antenna, make sure the three points as
below:
1. The area under the antenna end of the module should be keep clear of metallic components,
connectors, vias, traces and other materials that can interfere with the radio signal.
2. The area around the antenna end the module protrudes at least 10mm from the mother board PCB
and any metal enclosure.
3. When planning PCB layout, it is recommended that user places the antenna of Wi-Fi module as close
as possible to the edge of boarder to ensure the good performance of antenna, which is shown in the
picture below
4.3
IPEX Connectors
The external antenna is also supported by this wifi module, the dimension of IPEX connector
shown as below.
5 Reference Design
5.1 Power Supply
1. For the devices using power source of 5V, the UARTs of host device and Wi-Fi module can be
connected directly as the picture above to start communicating.
2. If the 5V power is supplied by LDO, the recommended capacitance C1 could be 10uF-22uF, if
the 5V power is supplied by DCDC, the recommended capacitance C1 could be at least 100uF
for electrolytic capacitor
3. When the wifi module is working, the peak current could reach more than 350mA, the
suggested current supply should be more than 400mA.
a. It is a OEM/Integrators Installation Manual;
b. The module is limited to OEM installation ONLY;
c. The OEM integrators is responsible for ensuring that the end‐user has no manual
instruction to remove or install module;
d. The module is limited to installation in mobile or fixed application;
e. The separate approval is required for all other operating configurations;
6 Warning
6.1 Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware‐limited to
channels 1 through 13.
This device and its antenna(s) must not be co‐located with any other transmitters
except in accordance with FCC multi‐transmitter product procedures.
Refering to the multi‐transmitter policy, multiple‐transmitter(s) and module(s) can be
operated simultaneously without C2PC.
This module is intended for OEM integrator. The OEM integrator is responsible for
the compliance to all the rules that apply to the product into which this certified RF
module is integrated. Additional testing and certification may be necessary when
multiple modules are used.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and
operated. The end user has to be informed that the FCC radio‐frequency exposure
guidelines for an uncontrolled environment can be satisfied. The end user has to also
be informed that any changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this equipment.
If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19
statement is required to be available in the users manual: This device complies with
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains
TX FCC ID: 2AHH3‐5005HBS ". If the size of the end product is larger than 8x10cm,
then the following FCC part 15.19 statement has to also be available on the label:
This device complies with Part 15 of FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Contact Us
Hangzhou Gubei Electronics Technology Co., Ltd.
Room 106, Building 1, No. 611 Jianghong Road, Binjiang, Hangzhou, Zhejiang, P.R.China
E Mail: henry.wen@broadlink.com.cn

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jumy
Create Date                     : 2016:03:11 10:21:09+08:00
Modify Date                     : 2016:03:11 10:21:09+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - 5005-HBS datasheet English version-10：10.doc
Creator                         : Jumy
Document ID                     : uuid:57a60e64-0ad4-41d8-be4e-47b620dfd2b5
Instance ID                     : uuid:f8fd8daa-b3b2-4b04-b183-63ed717769e1
Page Count                      : 15

EXIF Metadata provided by EXIF.tools