TCL Technoly Electronics 11 Wireless Module User Manual

TCL Technoly Electronics (Huizhou) Co., Ltd. Wireless Module

User Manual

TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
TCL Tonly Confidential
device. undesired operation.2.This device must accept any interference received, including interference that may cause1.This device may not cause harmful interference.conditions:This device complies with part 15 of the FCC Rules. Operation is subject to the following two For IC: This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d'Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. For FCC: Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.  “The device must not be co-located or operating in conjunction with any other antenna or transmitter.” FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.L'appareil doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateuet votre corps.FCC ConditionsLe présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radioexempts de licence.L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,même si le brouillage est susceptible d'en compromettre le fonctionnement.
Antenna Gain : 2dBiAntenna Type:PCB AntennaFor Subwoofer:Antenna Gain :3.08dBiAntenna Type:FPCB AntennaThis device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) For all products market in United States, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. And OEM shall not supply any tool or info to the end-user regarding to change the domain selection. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example: Access point, Wireless Router, Notebook, etc.). The final end product must be labeled in a visible area with the following: “Contains FCC ID: ”. ZVA11For Sound Bar:

Navigation menu