TCL Technoly Electronics 11 Wireless Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3959235
Application ID	Ts6HQ4f0TTtdl4oUiyBPEg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	126.66kB (1583217 bits)
Date Submitted	2018-08-10 00:00:00
Date Available	2018-08-10 00:00:00
Creation Date	2018-07-16 21:02:40
Producing Software	pdfFactory Pro 5.34 (Windows 7 Ultimate x64 Chinese (Simplified))
Document Lastmod	0000-00-00 00:00:00
Document Title	无线模组TWM-IA3S4规格书V1.1
Document Creator	pdfFactory Pro www.pdffactory.com
Document Author:	pc

TC
nl
To
ti
al
en
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
TC
To
nl
en
ti
al
id
nf
Co
L
TC
nl
To
ti
al
en
id
nf
Co
For IC:
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à
RSS247 de Canada d'Industrie. This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radioexempts de licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
The device should be installed and operated with a minimum distance of 20cm between the
radiator and your body.
L'appareil doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateu
et votre corps.
For FCC:
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.

“The device must not be co-located or operating in conjunction with any other
antenna or transmitter.”
FCC RF Radiation Exposure Statement Caution: To maintain compliance with the
FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that may cause
undesired operation.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
3) For all products market in United States, OEM has to limit the operation channels in CH1
to CH11 for 2.4G band by supplied firmware programming tool. And OEM shall
not supply any tool or info to the end-user regarding to change the domain selection.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for
example certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID cannot be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users (for
example: Access point, Wireless Router, Notebook, etc.). The final end product
must be labeled in a visible area with the following: “Contains FCC ID: ZVA11 ”.
For Sound Bar:
Antenna Type:FPCB Antenna
Antenna Gain :3.08dBi
For Subwoofer:
Antenna Type:PCB Antenna
Antenna Gain : 2dBi

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Title                           : 无线模组TWM-IA3S4规格书V1.1
Author                          : pc
Creator                         : pdfFactory Pro www.pdffactory.com
Producer                        : pdfFactory Pro 5.34 (Windows 7 Ultimate x64 Chinese (Simplified))
Create Date                     : 2018:07:16 21:02:40+08:00
Page Count                      : 12
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools