TCL Technoly Electronics OH000010 Bluetooth Module User Manual XXXX Module Datasheet
TCL Technoly Electronics (Huizhou) Co., Ltd. Bluetooth Module XXXX Module Datasheet
User Manual
Bluetooth Module Datasheet
蓝牙模组规格说明书
版本 Version：V1.0
公布日期 Release Date: 2017-06-28
TONLY ELECTRONICS HOLDINGS LIMITED.通力电子控股有限公司
Address:Section 37, Zhongkai Hi-tech Development Zone, Huizhou Guangdong 516006,
P.R.China
地址：中国广东省惠州市仲恺高新区惠风 6路37 号小区
网址 http://www.tonlyele.com
©2015 TONLY ELECTRONICS HOLDINGS LIMITED. All rights reserved 保留所有版权
XXXX Module Datasheet
2 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
法律声明 Legal Notice,Disclaimer,Copyright
本手册是通力电子控股有限公司机密，未经能力电子控股有限公司的事先书面许可，任何人不得复制、
传播本手册的内容。通力电子控股有限公司不对由使用本手册或执行本手册内容带来的损害负责。
本手册所涉及的知识产权归通力电子控股有限公司所有（或经合作商授权许可使用），任何人不得侵
犯。
本手册是按当前状态提供参考，本公司司保留随时更新本手册的权利,恕不另行通知。
本手册不对包括但不限于下列事项担保：适销性、特殊用途的适应性;实施该用途不会侵犯第三方的知
识产权等权利。 本文档在此未以禁止反言或其它方式授予任何知识产权使用许可，不管是明示许可还是暗
示许可。
本手册中提到的所有商标名称、商标和注册商标均属其各自所有者的财产，特此声明.
本协议以中、英文两种语言制作，两种语言文本冲突时，任何时候均以英文为准。
This data sheet contains information that is confidential to TONLY ELECTRONICS HOLDINGS
LIMITED. Unauthorized use or disclosure of the information contained herein is prohibited. You
may be held responsible for any loss or damages suffered by TONLY ELECTRONICS HOLDINGS
LIMITED . for your unauthorized disclosure hereof, in whole or in part.
Information herein is subject to change without noticed. TONLY ELECTRONICS HOLDINGS
LIMITED does not assume any responsibility for any use of, or reliance on, the information
contained herein
THIS DATA SHEET AND ALL INFORMATION CONTAINED HEREIN IS PROVIDED “AS IS”
WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE.
TONLY ELECTRONICS HOLDINGS LIMITED. SPECIFICALLY DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR
PURPOSE. NEITHER DOES TONLY ELECTRONICS HOLDINGS LIMITED. PROVIDE ANY
WARRANTY WHATSOEVER WITH RESPECT TO THE SOFTWARE OF ANY THIRD PARTY WHICH
MAY BE USED BY, INCORPORATED IN, OR SUPPLIED WITH THIS DATA SHEET, AND USER AGREES
TO LOOK ONLY TO SUCH THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. TONLY
ELECTRONICS HOLDINGS LIMITED. SHALL ALSO NOT BE RESPONSIBLE FOR ANY TONLY
ELECTRONICS HOLDINGS LIMITED DELIBERABLES MADE TO USER’S SPECIFICATION OR TO
CONFORM TO A PARTICULAR STANDARD OR OPEN FORUM.
Tonly is a trademark of TONLY ELECTRONICS HOLDINGS LIMITED. other names mentioned in this
document are trademarks/registered trademark of their respective owners.
This data shall be executed in two languages including one Chinese and one English. Any conflict
exist between the two languages, the English will prevail in any time.
XXXX Module Datasheet
3 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
版本变更说明 Document Revision History
Revision
版本
Date
日期
Author
作者
Description
描述
V1.0 2017-06-28 孙强耀 First release.
XXXX Module Datasheet
4 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
目录 Table of Contents
法律声明 Legal Notice,Disclaimer,Copyright
文档变更说明 Document Revision History
目录 Table of contents
1.系统概览 System overview
1.1 通用说明 General Descriptions
1.2 性能特点 Features
1.3系统方框图 Block Diagram
2.产品描述 Production Description
引脚与功能说明 Pin Layout & Pin Description
外观与尺寸 Appearance& Dimension
3.应用说明 ApplicationExplanation
4.电气特性 ElectricalCharacteristics
工作条件
直流特性 DC characteristics
电流消耗 Current consumption
5.射频性能 RF Performance
6.认证与法规信息 Certificate& Regulation
7.包装与订货说明 Package& Ordering information
8.环保声明 Green Policy
9.抗静电保护 ESD Protection
EXM1020
EXM1020
EXM1020
XXXX Module Datasheet
5 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
1.系统概览 System overview
Bluetooth Low Energy Module provides a highly integrated solution
for delivering low power Bluetooth v4.2 solutions. The advanced command
interface offers rapid time to market .
module complies with Bluetooth specification version v4.2. It
integrates RF, a baseband controller, making it a complete Bluetooth Low
Energy Solution.
can be used with either low cost microcontroller for intelligent
Bluetooth Low Energy applications. For simple sensor applications, the
internal scripting capabilities enable basic functions to be implemented
without the need for external host MCU or software development tools
EXM1020
XXXX Module Datasheet
6 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
2.产品说明 Production Description
Fully qualified Bluetooth version 4.2 low Energy Module
Command interface API over SPI
Castellated SMT pads for easy and reliable PCB Mounting
Environmentally friendly, RoHS compliant
Device Firmware Upgrade (DFU) over SPI or Over the Air (OTA)
Remote commands over the air
Antenna ready
Figure as below.
XXXX Module Datasheet
7 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
Pin feature descriptions
PIN
NO.
Symbol Description Function
1 VSS[4] GND. GND
2 VSS[5] GND. GND
3 I2S_WS Word select PIO[13]
4 I2S_CLK Continuous serial clock PIO[12]
5 I2S_SDA Serial data PIO[11]
6 PIO10 Programmable I/O. PIO[10]
7 VDD_Flash Power supply for Flash Type 3.3V
8 PIO9 Programmable I/O. PIO[9]
9 PIO8 Programmable I/O PIO[8]
10 Flash1_D0 External flash data in PIO[5]
11 Flash1_CLK
External flash CLK PIO[6]
12 Flash1_DI
External flash data out PIO[4]
13 Flash1_CS
External flash CS PIO[6]
14 SPI_MIOS Programmable I/O line or debug SPI
MISO selected by SPI_PIO#.
•SPI_MISO
•PIO[3]
15 SPI_MOSI Programmable I/O line or debug SPI
MOSI selected by SPI_PIO#.
•SPI_MOSI
•PIO[2]
16 SPI_CS# Programmable I/O line or debug
SPIchip select (CS#) selected
bySPI_PIO#
•SPI_CS#
•PIO[1]
17 SPI_CLK Programmable I/O line or debug SPI •SPI_CLOCK
XXXX Module Datasheet
8 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
CLK selected by SPI_PIO#. •PIO[0]
18 SPI_PIO# SPI/PIOactive-high. Input with internal pull down;
selects SPI Active-high.
19 PIO[14] Programmable I/O. PIO[14]
22 VDD_MEM VBAT for internal flash
23 VDD_BAT Power supply for moudle
24 AIO[0] Bi-directional with programmable
analog I/O.
Analogue Programmable I/O
3.应用说明 Application Explanations
Smart Audio
Smart light
IOT
4. 电气特性 Electrical Characteristics
ELECTRICAL CHARACTERISTICS
Supply Voltage 0.9 – 3.6V DC
(Absolute Maximum Ratings 0-3.6V)
Working current Depends on profiles, 3 mA (typical)
Standby current(disconnected) 3 mA
CURRENT CONSUMPTION (Power supply DC 3.0V)
Dormant 2.0uA
Deep Sleep 13 uA
Idle 1.5 mA
Tx/Rx active 5.5 mA at 4 dBm/5.5 at -90 dBm
WEIGHT AND DIMENSIONS (unit : mm)
Size 18 X14 X 2.3 (L x W x H)
Weight *?G
IC
XXXX Module Datasheet
9 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
5.射频性能 RF Performance
Specification Description
RF performance
Standard Bluetooth 4.2
Frequency Band 2.4 ~ 2.4835 GHz
Modulation Method GFSK
Maximum Data Rate 1 Mbps
Antenna PCB Antenna
Interface UART, PIO, AIO, SPI,PCM,
Operation Range 30 meters
Sensitivity -85 dBm at 0.1% BER
RF TX Power +0 dBm (avg), +4 dBm(peak)
6.认证与法规信息 Certification& Regulation
The BQB Certification：still on-going.
FCC ID：
：
ZVAOH000010
9976A-OH000010
XXXX Module Datasheet
10 TONLY ELECTRONICS HOLDINGS LIMITEDConfidential
7.环保声明 Green Policy
This module can meet ROHS&REACH compliance.XXXX
8.抗静电保护 ESD Protection
For IC:
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à
RSS247 de Canada d'Industrie. This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device. appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un
brouillage susceptible de provoquer un fonctionnement indesirable.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
For FCC:
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
“The device must not be co-located or operating in conjunction with any other
antenna or transmitter.”
FCC RF Radiation Exposure Statement Caution: To maintain compliance with the
FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
The device should be installed and operated with a minimum distance of 20cm between the
radiator and your body.
L'appareil doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateu
et votre corps.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
3) For all products market in United States, OEM has to limit the operation channels in CH1
to CH11 for 2.4G band by supplied firmware programming tool. And OEM shall
not supply any tool or info to the end-user regarding to change the domain selection.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for
example certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID cannot be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users (for
example: Access point, Wireless Router, Notebook, etc.). The final end product
must be labeled in a visible area with the following: “Contains FCC ID:
ZVAOH000010”.
Module Antenna Type: PCB ANT, 1.1dBi gain