TCT Mobile 440 One touch-H200 3G Router User Manual RAD440 V2
TCT Mobile Limited One touch-H200 3G Router RAD440 V2
RAD440 User Manual V2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2134159 |
| Application ID | H+kmbGbzRZc3wt5PLtih2Q== |
| Document Description | RAD440 User Manual V2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 44.37kB (554669 bits) |
| Date Submitted | 2013-12-05 00:00:00 |
| Date Available | 2013-12-06 00:00:00 |
| Creation Date | 2013-12-04 10:15:38 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2013-12-04 10:15:38 |
| Document Title | RAD440 User Manual V2 |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | auther |
User Manual FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. There is no country code option in the WIFI setting. In the USA, only 11 channels are available for 802.11 operation, the following table provides the frequencies for the 11 channels: Channel Number Center Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 2452 10 2457 11 2462 User Manual of Onetouch-H200 3G Router Table of Contents Hardware Description and Device connection .............................. 2 1.1 Hardware Description.................................................... 2 1.1.1 LED Indicator Status ............................................. 2 1.1.2 Interface Description ............................................. 3 1.2 Device Connection ........................................................ 3 1.2.1 Device Install ......................................................... 3 PC Setting...................................................................................... 4 WIFI Connection ........................................................................... 6 Web Configuration ........................................................................ 7 4.1 Language Setting ........................................................... 8 4.2 Setup Wizard ................................................................. 8 4.3 Network Setup ............................................................. 10 4.3.1 WAN Interface Setup........................................... 10 4.4 Wireless Setup ............................................................. 13 4.4.1 Basic Setup .......................................................... 13 User Manual of Onetouch-H200 3G Router Hardware Description and Device connection 1.1 Hardware Description 1.1.1 LED Indicator Status This 3G router contains 8 LED indicators. User can easily check the situation of device by observing LED indicator’s status Definition of LED Indicators follows below table. LED Indicator PWR WPS LAN1/2 PPP WiFi Status Description Light Power on and normal operation Off Power off or failure Light Connected Blink Connecting Off Closed or not used Light Lan port is on without data transporting Blink Lan port is on with data transporting Off Lan port is off Light Connected Blink Data transporting Off Connection off Light WiFi radio is on without data transporting Blink WiFi radio is on with data transporting Off WiFi radio is off Light In use Off Stand by Light Registered on network PHONE 2G/3G User Manual of Onetouch-H200 3G Router LED Indicator Status off Description Disconnected to network 1.1.2 Interface Description Interface and button description follows the below table. Interface/Button Description SIM slot Place to insert SIM card VOIP Voice interface (RJ11) for phone connection Lan1/2 LAN port for switch, concentrator and PC with network adaptor WPS WPS PBC mode control button. Reset By pressing the button for 3-6 seconds, the system will restore the default setting. Power Interface for power adaptor On/Off Press for power on/off 1.2 Device Connection 1.2.1 Device Install Device should be connected by following procedure: Step 1: insert the RJ45 cable in package to the LAN port of your device Step 2: insert another port of RJ45 cable to your PC Step 3: connect the power adaptor to the power slot of your device User Manual of Onetouch-H200 3G Router PC Setting In default setting, the IP address of LAN of the device is 192.168.1.1, DNS server address is 255.255.255.0，DHCP Server on. When PC connected to Onetouch-H200, normally the user needs to set the TCP/IP of PC according to follow procedure. Step 1: Click the right bottom as red part, then click “Open Network and Sharing Center”. Step 2:Click “Local Area Connection” Step 3: Click the “Properties” of Ethernet, then double-click “TCP/IPv4” User Manual of Onetouch-H200 3G Router Step 4: Normally the user should choose “Obtain an IP address automatically, then Click “OK”. Also the user can choose “Use the following IP address” as below pictures, set “IP address” as 192.168.1.X (any figure from 2-254), DNS server address as 255.255.255.0. Step 5: after configuration, select “Start”, input “ping 192.168.1.1” in command to check if PC and 3G router has been right connected. User Manual of Onetouch-H200 3G Router Note: 192.168.1.1 is the default IP address of LAN of the 3G router. If the IP address has been changed, please modify the IP address to current one. Step 6: if connected successfully, the page will show like below. WIFI Connection The connection of WIFI adaptor of PC to OneTouch-H200 should follow below steps. Step 1: Click “WIFI connection” in right bottom of desktop. User Manual of Onetouch-H200 3G Router Step 2: Choose the right WIFI hotspot, click “Connect”, when it shows “connected”, it means PC has been connected to WIFI. Note: Default SSID ofOneTouch-H200 is H200-XXXX (XXXX is the last four digits of its Mac) Step 3: If you have problem with the SSID of the device, please log on the device, choose “Wireless Setup”-“Basic Setup”, then check the current SSID. Web Configuration User Manual of Onetouch-H200 3G Router 4.1 Language Setting After log on Web page, user can set the language in the up-right part of web page. Simple Chinese and English have been offered. User can choose either one of them, then click “Apply”. 4.2 Setup Wizard Through Setup Wizard, user can configure basic networkparameter. Fast configuration should follow below procedures: Step 1: After log on, click “Setup Wizard” to start the configuration. Step 2: if user has good knowledge of router configuration, you can select “No. I Want To Configure The Router Myself”. If user wants to use Setup Wizard to configure the router, select “Yes”, then click “Next”, the page will show like below: User Manual of Onetouch-H200 3G Router Description of the page is like below table. Domain Description ISP Choose the ISP that provides the SIM card Account Input the account provided by ISP Password Input the password provided by ISP Dial Number Input the dial number provided by ISP (Default setting as above) Modem Baudrate 3G network transporting speed Authentication Method Authentication method of 3G dial-up APN Input access point name MTU Maximum transmission unit Connection Mode Connection mode of 3G dial-up Idle Timeout minutes) (In If connection mode set as “dial on demand”, set the idle timeout here to apply non-operation disconnecting. Name (DNS) Input the DNS provided by ISP. If you ISP didn’t provide it,please choose “Get Automatically From ISP”. Domain Server Address Primary DNS If necessary, input IP address of primary DNS. Secondary DNS If ISP provides another DNS, input the IP address here. Step 3: Configure WIFI network WIFI fast configure as below: User Manual of Onetouch-H200 3G Router Description of the page is like below page. Domain Description Enable When click-on, the WIFI LED indicator will be green-lighted, client can connect to the router through WIFI SSID Wireless network name. Maximum the SSID can contain 32 character, including letter, digit, underline. The SSID differs capital and small. Visibility Status Set the visibility of SSID Security Options Security option is used for encryption of the wireless network, preventing from unauthorized save and load and monitor. Five options have been provided. Please refer to wireless setting part for the details. After configuration, please click “Apply”, the wireless configuration will be finished then. 4.3 Network Setup 4.3.1 WAN Interface Setup Click “Network Setting”-“WAN Interface Setting 10 User Manual of Onetouch-H200 3G Router In above page, user can configure the relevant parameter according to actual requirement. Domain Description 2G/3G AUTO/2G/3G。 ISP Choose the ISP that provides the SIM card Account Input the account provided by ISP Password Input the password provided by ISP Dial Number Input the dial number provided by ISP (Default setting as above) Modem Baudrate 3G network transporting speed Authentication Method Authentication method of 3G dial-up APN Input access point name MTU Maximum transmission unit 11 User Manual of Onetouch-H200 3G Router Domain Description Connection Mode Auto Connect: when the user chooses “Auto Connect”, the system will connect automatically. If disconnected by other reason, the system will try to re-connect every 10 seconds. If the user pay monthly for the service, it is recommended to adopt this mode. Dial on Demand: when the user choose “Dial on Demand”, if there is any request for visiting the internet, the system will dial up automatically. If non-operation during the set idle timeout, the system will disconnect by itself. This mode is suitable for user who pays according time. Manually Connect: when the user chooses “Manually Connect”, he should dial up manually. Idle Timeout minutes) (In If stand by time reaches the set value, the connection will be cut. Name (DNS) Input the DNS provided by ISP. If you ISP didn’t provide it, please choose “Get Automatically From ISP”. Domain Server Address Primary DNS If necessary, input IP address of primary DNS. Second DNS If ISP provides another DNS, input the IP address here. 12 User Manual of Onetouch-H200 3G Router 4.4 Wireless Setup 4.4.1 Basic Setup Click “Wireless Setup”-“Basic Setup” Domain Region Enable Broadcast Description Choose the region you are located in SSID When enable SSID broadcast, the SSID will broadcasted in wireless network and visible to user. be Enable Wireless Isolation When enable wireless isolation, the same SSID user can’t communicate with each other. Name (SSID) Wireless network name. Maximum the SSID can contain 32 character, including letter, digit, underline. The SSID differs capital and small. 13 User Manual of Onetouch-H200 3G Router Domain Description Mode Choose the wireless mode, default as “Mixed 802.11b/g/n” 802.11b only–Maximum Rate is 11 Mbps。 Mixed 802.11b/g –Compatible with 802.11b and 802.11g Mixed 802.11b/g/n –Compatible with 802.11b, 802.11n and 802.11g Channel Choose wireless network channel. Default set as “Auto”, the device will search for the best available channel. Band Width Choose the right band width. Band width of 20M provides maximum 130Mbps rate. Band width of 40M provides maximum 270Mbps. Max Transmission Rate All the supported rates have been listed. Please choose the right one as the maximum transmission rate. Security Options Security option is used for encryption of the wireless network, preventing from unauthorized save and load and monitor. 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 17 Language : en-US Tagged PDF : Yes Author : auther Creator : Microsoft® Office Word 2007 Create Date : 2013:12:04 10:15:38+08:00 Modify Date : 2013:12:04 10:15:38+08:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools